Benutzeranleitung / Produktwartung FS 9530DN des Produzenten Kyocera
Zur Seite of 172
Advanced Operation Guide FS-9130DN FS-9530DN.
.
Contents ADVANCED OPERATION GUIDE i Content s 1 Handling Paper ............... ................ ................ ................ ................. ............ ................. ... ...........1-1 General Guidelines ............... ................. .
Contents ii ADVANCED OPERATION GUIDE.
ADVANCED OPERATION GUIDE iii Introduction This guide has the following chapters: • 1 Handling Paper Explains how to cho ose, handle and load paper. • 2 Using the Op eration Panel Explains how to use the operation pa nel to configure the printer. • 3 Fonts Shows the available fonts.
iv ADVANCED OPERATION GUIDE Conventions This manual uses the following conventions: Convention Description Example Italic Typeface Used to emphasize a key word, phrase or re ferences to additional information. Close the top cover . Refer to T oner Cont ainer Replacement on page 3-3 .
ADVANCED OPERATION GUIDE 1-1 1 Handling Paper This chapter explains the following topics: • General Guidelines..... .......................................... ....... 1-2 • S pecial Paper ............. .......................................... ..
Handling Paper 1-2 ADVANCED OPERATION GUIDE General Guidelines The printer is desi gned to print on high -quality copier bond pape r (the kind used in ordinary dry copier mach ines), but it can also accept a variety of other types of paper within the limits specified below.
Handling Paper ADVANCED OPERATION GUIDE 1-3 Paper Specifications The following table summarizes the basic paper specifications. Details are given on the following pages. Minimum and maximum p aper sizes The minimum and maximum paper size s are as follows.
Handling Paper 1-4 ADVANCED OPERATION GUIDE Selecting the Right Paper Laser printing is a process involving laser light, electrosta tic discharge, toner, and heat. In addition, as the pap er passes through the printer it undergoes considera ble sliding, bend ing, and twisting motions.
Handling Paper ADVANCED OPERATION GUIDE 1-5 Paper with other sizes (custom sizes) can also be fed from th e MP tray. The minimum size paper for man ual feed is 88 × 148 mm (3-1/2 × 5- 13/16 inches), fed lengthwise. The maximum size is 297 × 450 mm (11-11/16 × 17-3/4 inches).
Handling Paper 1-6 ADVANCED OPERATION GUIDE Paper Weight Equiv alence T able The paper weight is listed in pounds (l b) and metric grams per square meter (g/m 2 ). The shaded part indicates the sta ndard weight. Thickness (Calipe r) Thick paper is referred to as high-ca liper paper and thin paper as low- caliper paper.
Handling Paper ADVANCED OPERATION GUIDE 1-7 Moisture Co ntent Moisture content is defined as the perc ent ratio of moisture to the dry mass of the paper. Moisture ca n affect the paper’s appea rance, feedability, curl, electrostatic proper ties, and toner fusi ng characteristics.
Handling Paper 1-8 ADVANCED OPERATION GUIDE Electrostatic properties: During the printing process, the paper is electrostatically charged to attract th e toner. The paper must be able to release this ch arge so th at printed s heets do not clin g together in the output tray.
Handling Paper ADVANCED OPERATION GUIDE 1-9 S pecial Paper This section explains printing on sp ecial paper . The page printer can use the following type s of special paper.
Handling Paper 1-10 ADVANCED OPERATION GUIDE T ransp arency Transparency must be able to withstand the heat of fu sing during the printing process. It should satisfy the conditions given in the table below. If transparency jams frequently, pull the top of th e sheet very gently as it leaves the printer.
Handling Paper ADVANCED OPERAT ION GUIDE 1-11 Some label paper is manufactured with an extra marg in of top sheet around the edge. Do not remove the extra top sheet from the carrier sheet until after printing is finished. The table below lists the specific ations for adhesive label paper.
Handling Paper 1-12 ADVANCED OPERATION GUIDE Do not use envelopes that have an encapsulated liquid a dhesive. Avoid long printing runs consistin g of envelopes only.
Handling Paper ADVANCED OPERAT ION GUIDE 1-13 Media T ype The printer is capable of printing unde r the optimum setting for the typ e of paper being used.
Handling Paper 1-14 ADVANCED OPERATION GUIDE Loading Paper The following explains the produre for loading paper. Paper can be loade d into the two paper cassettes and th e MP tray. IMPORTANT: Fan the paper, then tap it on a leve l surface. This avoid media jams or skew ed printing.
Handling Paper ADVANCED OPERAT ION GUIDE 1-15 2 Hold the paper guide and mo ve it to align the paper guide with th e required paper width. Paper sizes are marked in side the paper cassette.
Handling Paper 1-16 ADVANCED OPERATION GUIDE 3 Hold the paper stopper and move it to align with the requ ired paper length. 4 Set the paper flush against the left-hand wall of the paper cassette. IMPORTANT: There is a sticker ( in the illustration) indicating paper capacity attached to the inside of the paper cassette.
Handling Paper ADVANCED OPERAT ION GUIDE 1-17 5 Set the supplied paper size plate so that the size of the paper loaded can be checked by looking at the fron t of the paper cassette.
Handling Paper 1-18 ADVANCED OPERATION GUIDE Loading Paper into the MP (Multi-Purpose) T ray Special paper as well as standard pape r can be loaded into the MP tray.
Handling Paper ADVANCED OPERAT ION GUIDE 1-19 3 Adjust the insert guides to the size of the paper to be loaded. 4 Insert the paper al ong the guides as far as it will go. IMPORTANT: When loading pape r into the MP tray, make su re that the print side is facing upward.
Handling Paper 1-20 ADVANCED OPERATION GUIDE Setting Envelopes When using the optio nal printer function, envelopes can be set in the MP tray. NOTE: Do not print on envelopes with fl ap adhesive exposed. This can cause printer malfunction. 1 Open the MP tray.
Handling Paper ADVANCED OPERAT ION GUIDE 1-21 NOTE: Do not load more paper than w ill fit under the load limits on the inside of the MP tray . If the paper is considerably cu rled in one direction, for example, if the p aper is already printed on one side , try to roll the paper in the opposite direction to co unteract the curl.
Handling Paper 1-22 ADVANCED OPERATION GUIDE.
ADVANCED OPERATION GUIDE 2-1 2 Using the Operation Panel This chapter explains the following topics: • Understanding the Oper ation Panel ............................ 2-2 • Canceling a Printing Job .......... ............................ ..... 2-10 • Using the Operation Panel .
Using the Operation Pane l 2-2 ADVANCED OPERATION GUIDE Underst anding the Operation Panel The operation panel has an LCD message display, indicators, and eight keys.
Using the Operation Panel ADVANCED OPERATION GUIDE 2-3 Operation Indicators The following indicators light up durin g normal operation and when the printer needs attention. Indicator Description Flashing: Indicates when an error occurs that you can clear by yourse lf.
Using the Operation Pane l 2-4 ADVANCED OPERATION GUIDE Message Display The message display gi ves information in the form of short messages. The nine messages listed below ar e displayed during normal warm-up and printing.
Using the Operation Panel ADVANCED OPERATION GUIDE 2-5 Indicators in Message Display The interface Indicator shows the interface tha t is currently used. It uses the following abbreviation s: Each interface has a timeout time of 30 seconds duri ng which the other interface should wait to receive a pr int job.
Using the Operation Pane l 2-6 ADVANCED OPERATION GUIDE * With only the MP tray feeding NOTE: While the printer is proc essing data, the SIZE display indicates the paper size selected by the application sof tware.
Using the Operation Panel ADVANCED OPERATION GUIDE 2-7 Media T yp e Indicator This shows the media type defin ed for the current paper cassette. Automatic cassette switch ing is available according to the media type. The media type can be specified at the oper ation panel.
Using the Operation Pane l 2-8 ADVANCED OPERATION GUIDE Keys The operatio n panel keys are used to configure the printer . Note that certain keys have a second ary function. NOTE: Settings made with these k eys affe ct only the interface currently in use.
Using the Operation Panel ADVANCED OPERATION GUIDE 2-9 Cursor Keys The four cursor keys are used in th e menu system to access an item or enter numeric values. The arrow key with the que stion mark ( ) may be pressed when the pa per jam message has appeared on the message display.
Using the Operation Pane l 2-10 ADVANCED OPERATION GUIDE Canceling a Printing Job 1 While the printer displays Processing , press [CANCEL] . Print Cancel? appears on the message display follo wed by the interface in use.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-11 Using the Operation Panel This section explains how to use the menu selection syst em. [MENU] on the operation pane l allows you to use the menu to set or chang e the printer environment such as the number of co pies to print, emulation, etc.
Using the Operation Pane l 2-12 ADVANCED OPERATION GUIDE Interface > Network Interface > Option Continued >Parallel I/F Auto >Baud Rate 115200 >Parity None >Protocol DTR(pos.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-13 Continued Continued on the next page >>I000 >>Size 012.00 point(s) >>Pitch 10.
Using the Operation Pane l 2-14 ADVANCED OPERATION GUIDE Continued Continued on the next page >Read Data >Write Data >Delete Data >Delete Font >Format >Print Partition List Hard Disk.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-15 Continued Continued on the next page >Read Data >Remove Device >RAM Disk Size >Read Data >Write Data >Delete Data >Delete .
Using the Operation Pane l 2-16 ADVANCED OPERATION GUIDE >>Duplex Path Disable Continued Continued on the next page Paper Handling > >Reset Type Adjust >MP Tray Size A4 >MP Tray Type.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-17 Continued >Printed Pages 0000001 Life Counters > Security > Others > >Sleep timer > 015 min. >Print HEX-DUMP >Restart Printer >MSG Language English >Form Feed Time Out 000sec.
Using the Operation Pane l 2-18 ADVANCED OPERATION GUIDE Continued >>Print Status Page >>Developer >>Charger >>Drum >Service > >>Paper Feed Normal >>Paper Fee.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-19 Using the Menu Selection System This section explains the proce dure for using the menu selection system. The menu selection system is activated by [MENU] while the printer is Ready . Printing the Menu Map The printer prints a full list of menu selections.
Using the Operation Pane l 2-20 ADVANCED OPERATION GUIDE Stat u s P a g e s This section explains the procedur e for printing the status pages. The status page is a list of parameters and settings for mo st basic printer configurations. You may be required to pr oduce a status page when requesting service to the printer.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-21 The following is a sample status page . The numbers below refer to the contents explained on the next page. When the Network Status is turned on, the Network Interface Status Page will be printed after the Prin ter Status.
Using the Operation Pane l 2-22 ADVANCED OPERATION GUIDE 6 Network Status This shows the IP address, Subnet Mask address, and Default Gateway address for the network in terface. 7E m u l a t i o n This shows all available emulations of the printer. The printer is shipped from the factory with PCL 6 emulation selected as the default.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-23 e-MPS e-MPS is an abbreviation for ‘enhanc ed-Multiple Printi ng System’ which implements the following functions that are available from t.
Using the Operation Pane l 2-24 ADVANCED OPERATION GUIDE * Jobs in excess will cause the earlier ones to be deleted. Job Stora ge Job storage stores print jobs either te mporarily or permanen tly, or in virtual mailboxes, as you click an appropriate radio button on the printer driver when printing from a computer.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-25 Using Quick Copy This mode enables you to print the requested number of copies of a job, simultaneously storing the job on the hard disk. When additional copies are required, you can reprint the req uired number of copies from the printer operation panel.
Using the Operation Pane l 2-26 ADVANCED OPERATION GUIDE 10 Press [OK] to finalize the copy count. Th e printer prints the specified number of copies for the job. Deleting a Quick Copy Job All quick copy jobs are automatically de leted when the printer is turned off.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-27 Releasing a Private Print/S tored Job 1 Press [MENU] . 2 Press U or V repeatedly until e-MPS > appears. 3 Press Z . 4 Press U or V repeatedly until >Private/ Stored appears. The na me entered in the printer driver ( Harold , in this example) also appears.
Using the Operation Pane l 2-28 ADVANCED OPERATION GUIDE Deleting a Private Print/S tored Job You can individually delete stored jobs by performin g the following procedure. Jobs sa ved using Private Print will be automatically deleted if you turn the power off after printing , but jobs saved using Stored Job will not be deleted automatically.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-29 Printing a Li st of Code Jobs If you select Permanent Job Storage o n the printer driver, you can have a List of Code Jobs printed using the oper ation panel. 1 Press [MENU] . 2 Press U or V repeatedly until e-MPS > appears.
Using the Operation Pane l 2-30 ADVANCED OPERATION GUIDE If you have named the virtual mailb ox with an alias on the printer driver, the alias ( Richard , in this example) will follow the number: 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press [OK] .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-31 Changing e-MPS Configuration You can change the following par ameters for e-MPS operation: • Maximum n umber of Q uick Copy/P roof-and-H old .
Using the Operation Pane l 2-32 ADVANCED OPERATION GUIDE Maximum Sp ace Assigned to T emporary Code Jobs This changes the hard disk space that holds temp orary code jobs. You can change the maximum sp ace from 0 to 99 99 (megabytes). Th e actual maximum size depends on the size of free hard disk space, howeve r.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-33 Maximum Sp ace Assigned to Permanent Code Jobs This changes the hard d isk space th at holds per manent code jobs. You can change the maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free hard disk space, howeve r.
Using the Operation Pane l 2-34 ADVANCED OPERATION GUIDE Maximum Sp ace Assigned to Virtual Mailboxes (VMB) This changes the hard d isk space for virtual m ailboxes. You can chang e the maximum space from 0 to 9999 (megabytes). The actual maximu m size depends on the size of fr ee hard di sk sp ace, however.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-35 Changing the Interface Parameters The printer is equi pped with both a parallel and serial interface or a network interface. F urther, an optio nal RS-232C inte rface card or network interfac e card may be installed if desired.
Using the Operation Pane l 2-36 ADVANCED OPERATION GUIDE 7 Press U or V to display the desired mode. The display chan ges as shown below. Press [OK] . Auto (default) Normal High speed Nibble (high) 8 Press [MENU] . The message display returns to Ready .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-37 6 Press Z . Setting items (e.g., Baud Rate ) are displayed in the message display. Pre ss U or V to display each setting item. 7 Display the setting item to be changed an d press [OK] . A blinking que stion mark ( ? ) appears.
Using the Operation Pane l 2-38 ADVANCED OPERATION GUIDE To confirm or change ne twork card parameters, proceed as fo llows: 1 Press [MENU] . 2 Press U or V repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interfac e.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-39 7 The following ex ample explains how to activate TCP/IP protocol to connect the printer in the network. You can select Netware or AppleTa lk in a similar manner. If TCP/IP is currently displays Off , select On using U or V .
Using the Operation Pane l 2-40 ADVANCED OPERATION GUIDE 12 Press [OK] . 13 Press [MENU] . The message display returns to Ready . Printing a Network In terface St atus Page You can print out a status page for the network interface.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-41 9 Press [OK] again. 10 Press [MENU] . The message display returns to Ready . >Network Status Page Off NETWORK ST A TUS P AGE FS-9530DN Page .
Using the Operation Pane l 2-42 ADVANCED OPERATION GUIDE Making Default Settings Using the operation p anel, you can se t the default for th e following items. Default Emulation The emulation mode for th e current interface can be chang ed. 1 Press [MENU] .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-43 4 Press U or V repeatedly until KPDL (AUTO) appears. 5 Press [OK] . 6 Press Z . When > Alt. Emulation is disp layed, press U or V . The names of alternative emulations appear . PCL 6 (default) KC-GL Line Printer IBM Proprinter DIABLO 630 EPSON LQ-850 7 Press [OK] .
Using the Operation Pane l 2-44 ADVANCED OPERATION GUIDE 6 Press Z . The message display chan ges to that shown below. If >Print KPDL Errs is displayed when the KPDL (AUTO) emulation is selected, press U or V to change it. 7 Press [OK] . A blinking question mark ( ? ) appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-45 8 Press U or V repeatedly until the desired pen number of 1 to 8 appears. 9 When the des ired pen nu mber is displa yed, press [OK] . 10 To change t he pen w idth, pres s Z , then press [OK] . A blinking cursor appears at the width value.
Using the Operation Pane l 2-46 ADVANCED OPERATION GUIDE 4 Press Z . The letter before the number indica tes the type of font as follows: 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press U or V repeatedly until the desired font number appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-47 7 Press [OK] . A blinking question mark ( ? ) appears. 8 Select Regular or Dark using U or V . 9 Press [OK] . 10 Press [MENU] and the message display returns to Ready . Changing the Default Font Size You can change the size of the default font.
Using the Operation Pane l 2-48 ADVANCED OPERATION GUIDE Setting the Character Pitch for Courier/Letter Gothic You can set the charac ter pitch for fixed-pitc h fonts whe n the default font is Courier or Letter Gothic. 1 Press [MENU] . 2 Press U or V repeatedly until Font > appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-49 4 Press U or V repeatedly until > Code Set appears. 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press U or V until the desired char acter code set appears. 7 Press [OK] . 8 Press [MENU] .
Using the Operation Pane l 2-50 ADVANCED OPERATION GUIDE 6 Press [OK] again. Processing appears, th en Ready . The printer pr ints a list of fonts with a short sample a nd font ID (number) for each font.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-51 Pagination In Page Set menus, you can set the number of copies, the page orientation, and other se ttings regarding pagination. Number of Copies You can set the number of co pies of each page to be prin ted for the current interface.
Using the Operation Pane l 2-52 ADVANCED OPERATION GUIDE Bring up the Zoom menu. The following display will appear. Source size indicator... This is the paper size befor e reduction. This must be the same as the paper size set for print data from the computer.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-53 1 Press [MENU] . 2 Press U or V repeatedly until Page Set > appears. 3 Press Z . 4 Press U or V repeatedly until >Zoom appears. 5 Press [OK] . A blinking cursor ( _ ) appears under the paper size.
Using the Operation Pane l 2-54 ADVANCED OPERATION GUIDE Printing Orient ation You can select the portrait or landscape page or ientation. The page orientation can be set whe never the message display indicates Ready . 1 Press [MENU] . 2 Press U or V repeatedly until Page Set > appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-55 3 Press Z . 4 Press U or V repeatedly until >Page Protect appears. 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press U or V repeatedly until Auto appears. 7 Press [OK] . 8 Press [MENU] .
Using the Operation Pane l 2-56 ADVANCED OPERATION GUIDE Carriage-Retur n (CR) Action This procedure instructs the printer what to do when it receives a carriage- return code (character code 0DH). 1 Press [MENU] . 2 Press U or V repeatedly until Page Set > appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-57 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Select On or Off using U or V . 7 Press [OK] .
Using the Operation Pane l 2-58 ADVANCED OPERATION GUIDE Setting Print Quality You can make the following settings to enh ance the print quality: Kyo cera Image Refinement (KIR), a software algor ithm.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-59 White vertical stripes Set the KIR mode to On . Try printing the status page again. If you still get white vertical stripes, adjust the print density control to a darker setting. 1 Press [MENU] .
Using the Operation Pane l 2-60 ADVANCED OPERATION GUIDE 1 Press [MENU] . 2 Press U or V repeatedly until Print Quality > appears. 3 Press Z . 4 Press U or V repeatedly until >EcoPrint Mode appears. 5 Press [OK] . A blinking question mark ( ? ) appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-61 Print Density The print density can be adjusted in five steps: from 01 (light) to 05 (dark). The factory setting is 03 . 1 Press [MENU] . 2 Press U or V repeatedly until Print Quality > appears.
Using the Operation Pane l 2-62 ADVANCED OPERATION GUIDE Operating the S torage Device The printer supp orts four types of storage device; Co mpactFlash card, USB flash memory, an option hard disk, and RAM disk. The CompactFlash card and USB flash memory are insta lled into the dedicated slots of the printer.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-63 6 Press [OK] . Processing appears and the reading of data fr om the memory card starts. 7 Press [MENU] to return to Ready . Reading Dat a Data stored on a memo ry card can be read. T o read data on a mem ory card, procee d as follows.
Using the Operation Pane l 2-64 ADVANCED OPERATION GUIDE 1 Press [MENU] . 2 Press U or V repeatedly until Memory Card > appears. 3 Press Z . 4 Press U or V repeatedly until >Write Data appears. 5 Press [OK] . A blinking question mark ( ? ) appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-65 Pa r ti t i on T yp e : Type of data written (currently only type 2 is supported). Partition Name: The destination name of data written to the card. Write Partition Length: The size of the written data on the memory card.
Using the Operation Pane l 2-66 ADVANCED OPERATION GUIDE Formatting Formatting allows data to be written to the card. A new memory card must be formatted before it can be used in th e printer. Formatting delet es any existing data on th e memory card.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-67 Printing a Li st of Data Names The printer prints a list of all data names ( referred to as partitions) stored in a memo ry card for re ference. (Pr inting a list is also available for a font card.
Using the Operation Pane l 2-68 ADVANCED OPERATION GUIDE Using USB Flash Memory The USB flash memory is available for only PDF file. PDF fil es should be stored on the root directory of USB flash memory. The PDF file name can be up to 99 single-byte characters in leng th.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-69 Removing USB Flash Memory When removing USB mem ory from the printer , be sure to proceed with this menu to ensure safe discon nection. NOTE: If you remove USB memory withou t performing this operation, an error message will appear .
Using the Operation Pane l 2-70 ADVANCED OPERATION GUIDE 6 Press [OK] . Processing appears, and the part ition list is printed. After the USB memory partition list is printed, the message display returns to Ready . Operating an Option Hard Disk By installing the option hard disk into the printer, the e-MPS function can be used.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-71 For example, if the total memory inst alled in your prin ter (FS-9130DN) is 64 MB (Default), you can set 28 MB of RAM disk.
Using the Operation Pane l 2-72 ADVANCED OPERATION GUIDE 10 Press [OK] . The selected RAM disk s ize is activated. 11 Press [MENU] . The message display returns to Ready . The operation s of the RAM dis k are the same as those of the m emory card. Refer to the relevant sections in Using the CompactFla sh Card on page 2- 62 .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-73 Paper Handling You can change the MP tray mode, th e paper size and type for each paper source, the sorter mode, the paper source, and paper destinations. MP T ray Mode The MP tray can be used in one of two modes: cassette mode or first mode.
Using the Operation Pane l 2-74 ADVANCED OPERATION GUIDE Setting the MP T ray Size When using the MP tray in the casse tte mode, you should s et the MP tr ay size to the paper size that is used to for mat the job to print.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-75 Envelope #6 Envelope DL Envelope C5 A6 B6 A5 B5 B5-R ISO B5 A4-R 7 Press [OK] . 8 Press [MENU] . The message display returns to Ready . Setting the MP T ray T ype You can automat ically select the p aper cassette acco rding to the selectio n made by the application (printer dr iv er).
Using the Operation Pane l 2-76 ADVANCED OPERATION GUIDE Letterhead Color Prepunched Envelope Cardstock Thick High quality Custom 1 ( to 8) 7 When the des ired MP tr ay type is dis played, press [OK] . 8 Press [MENU] and the message display returns to Ready .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-77 Paper Size Un it Selection The paper size unit (metric or inch system) used in the message display can be selected beforehand. At the time of Ready or when selecting the size display, the unit for some paper may be replaced with the co unterpart as shown in the following table.
Using the Operation Pane l 2-78 ADVANCED OPERATION GUIDE 7 Press U or V to select mm or inch . 8 Press [OK] . 9 Press [MENU] . The message display returns to Ready . Setting the Casset te Media T ype Make this setting to match the me dia type fed from the paper cassette of the printer.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-79 Selecting the Paper Feed Source You can select from which paper source printing will be performed. If no option units are installed, the only selectio ns are the paper cassette and MP tray of the printer.
Using the Operation Pane l 2-80 ADVANCED OPERATION GUIDE Activating the duplexer is done by selecting either short edge or long edge binding mode. NOTE: Duplex printing can be also performed from the MP tray .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-81 4 Press U or V repeatedly until >Duplex Mode appears. 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press U or V to disp lay the desired duplex mode. The display ch anges as shown below .
Using the Operation Pane l 2-82 ADVANCED OPERATION GUIDE Overriding Difference between A4 and Letter This selects whether to enable or disable the difference between A4 size and Letter size. Under the default se tting of Off , the paper size of the paper source is matched to th e paper size formatting the jobs.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-83 3 Press Z . 4 Press U or V repeatedly until >Type Adjust > appears. 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press U or V to display the desired paper type or a definable setting fr om among Custom 1 thro ugh Custom 8 to be reg istered.
Using the Operation Pane l 2-84 ADVANCED OPERATION GUIDE 3 Press [OK] . A blinking question mark ( ? ) appears. 4 Press U or V to display the desired paper thickness. The displa y changes as shown below. For details of the def ault setting for each paper type, refer to Media Type on page 1-13 .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-85 Resetting the Custom Paper T ype Resets the custom setting that are set in Creating Custom Pape r Type on page 2-82 . 1 Press [MENU] . 2 Press U or V repeatedly until Paper Handling > appears.
Using the Operation Pane l 2-86 ADVANCED OPERATION GUIDE Reading Life Counters You can display the total number of pages printed by your printer for confirmation whenever necessary . The total number of printed page s can also be checked on th e status page.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-87 Other Modes The modes described in the fo llowing pages can be accessed in the Others submenu. To enter the Others subme nu, press Z while Others > is displayed. The following submenus can be displayed by pressing Z and then U or V .
Using the Operation Pane l 2-88 ADVANCED OPERATION GUIDE 7 Press [OK] . 8 Press [MENU] . The message display returns to Ready . Automatic Form Feed Timeout Setting When the printer receives no data for a certain time, it times out and releases the current in terface: it prints whatever data it has in its buffer and feeds out the page.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-89 4 Press U or V repeatedly until >Sleep timer > appears. 5 Press Z and di splay >>Auto Sleep . 6 Press [OK] . A blinking question mark ( ? ) appears. 7 Select Off using U or V . 8 Press [OK] .
Using the Operation Pane l 2-90 ADVANCED OPERATION GUIDE Received Data Dumping It is possible to print da ta received by the printer a s hexadecimal code for the purposes of debugging programs and files. 1 Press [MENU] . 2 Press U or V repeatedly until Others > appears.
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-91 3 Press Z . 4 Press U or V repeatedly until >Restart Printer appears. 5 Press [OK] . A blinking question mark ( ? ) appears. 6 Press [OK] again. Self test appears while the printer is re setting itself, then Please Wait followed by Ready .
Using the Operation Pane l 2-92 ADVANCED OPERATION GUIDE 6 Press U or V to display the desired mode. The display chan ges as shown below. Off (default) Permanent Perm / Temp (Permanent/Tem porary) 7 When the desired mode is displaye d, press [OK] . 8 Press [MENU] .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-93 9 Press [OK] . Repeat steps 6 through 9 for each item to be changed. 10 Press [MENU] . The message display returns to Ready .
Using the Operation Pane l 2-94 ADVANCED OPERATION GUIDE Setting the Auto Continue Recovery Time Follow the procedure given below to change the recove ry time for Auto Continue . 1 Press [MENU] . 2 Press U or V repeatedly until Others > appears. 3 Press Z .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-95 Finishing These settings are possible only when the optional finisher is installed on the printer.
Using the Operation Pane l 2-96 ADVANCED OPERATION GUIDE St aple Error Detection Sett ing This setting controls whether or not message Add staples appears when the f inisher units runs out of staples d uring outpu t of a stab led job. 1 Press [MENU] .
Using the Operation Panel ADVANCED OPERAT ION GUIDE 2-97 Punch Error Detection Setting This setting is possible only when t he Punch Unit is ins talled on the optional finisher unit. This setting c ontrols whether or not the message Chad box full appears when the chad box on the punch unit becomes full.
Using the Operation Pane l 2-98 ADVANCED OPERATION GUIDE Service Menu The service menu contains maintenan c e operations to be performed by service person nel. The Print Status Page , Developer , and Drum menus appear; however, in general, you will on ly need to use the Print Status Page menus.
ADVANCED OPERATION GUIDE 3-1 3 Font s This chapter contains ex planations on the following: • List of Fonts ........... .............................
Fonts 3-2 ADVANCED OPERATION GUIDE List of Font s This section contains a full list of the printer’s internal fonts. The prin ter has 80 PCL fonts and 136 PostScript Level 3 compa tible fonts, as well as 1 bitmap font. You can pr int the font list from the printer by using the prin ter’s operation panel key.
Fonts ADVANCED OPERATION GUIDE 3-3 PCL (Scalable and Bitmap) Font s.
Fonts 3-4 ADVANCED OPERATION GUIDE KPDL Font s (1).
Fonts ADVANCED OPERATION GUIDE 3-5 KPDL Font s (2).
Fonts 3-6 ADVANCED OPERATION GUIDE.
ADVANCED OPERATION GUIDE 4-1 4 Options This chapter contains explanat ions on the following topics: • General Information..... ......................................... ....... 4-2 • Network Interface ....... ......................................
Options 4-2 ADVANCED OPERATION GUIDE General Information The printer has the following options available. For instructions on installing individual options, refer to the documentatio n included with the option.
Options ADVANCED OPERATION GUIDE 4-3 PF-700 Paper Feed er Holds approximately 500 shee ts of A5 to A3 or Ledger size paper. Up to two paper feeders can be attached to the bottom of the printer . PF-750 Paper Feed er Holds approximately 300 0 sheets of A4, B5 or Letter size paper .
Options 4-4 ADVANCED OPERATION GUIDE DF-710 Document Finis her Provides finishing with about 3,000 shee ts at a time with high-speed and large-capacity processes. Also provides a punch function. They are installed to the left side of the printer . DF-730 Document Finis her Provides finishing with abou t 1,000 sheets at a time.
Options ADVANCED OPERATION GUIDE 4-5 •M e m o r y D I M M See your dealer for purch asing information of the DIMM that are best suited for use with this printer.
Options 4-6 ADVANCED OPERATION GUIDE Network Interface The FS-9130DN/FS-9530DN have the stand ard Network interface. This printer supports the TCP /IP, IPX/SPX, NetBEUI, and AppleTalk protocols, so the network printing under vario us platforms such as Windows, Macintosh, UNIX, and NetWare is available.
Options ADVANCED OPERATION GUIDE 4-7 4 Connect the network cable. 5 Set the network address from th e printer operation panel (for de tails about the modes,r efer to Changin g Network Interf ace Paramete rs o n page 2-37 ).
Options 4-8 ADVANCED OPERATION GUIDE Hard Disk Insert the hard disk into op tion hard disk unit slot on the printer. If a hard disk unit is installed in the printer, received data can be raster ized and stored on this hard disk. This enables high-speed printing of multiple copies using an electric s ort function .
Options ADVANCED OPERATION GUIDE 4-9 4 Tighten the two screws to secure the hard disk unit to the ma in circuit board..
Options 4-10 ADVANCED OPERATION GUIDE Comp actFlash (Memory) Card Insert the memory card into the memory card slot located on the right side of the printe r. A memory ca rd is a mi crochip card that may contain option fonts, macro s, forms, etc. T he printer re ads the contents of th e card into its internal memory wh en printer is turned on.
Options ADVANCED OPERAT ION GUIDE 4-11 USB Flash Memory Connect the USB memory to the USB memo ry slot on the right side of the printer. You can then prin t PDF data stored in the USB memory. Consult your dealer for USB flash me mory usable with the printer.
Options 4-12 ADVANCED OPERATION GUIDE Exp ansion Memory Modules To expand the printer memory fo r more complex print jobs and faster print speed, you can plug in optional memory module (dual in line memory module) in the memory slot provided on the printer main controller board.
Options ADVANCED OPERAT ION GUIDE 4-13 2 Remove the screw from the memory slot cover at the back of the pr inter and remove the memory slot cover. 3 Remove the DIMM from its package.
Options 4-14 ADVANCED OPERATION GUIDE 7 When you finish installing the DIMM, mount the memory slot cover and fasten it with the screw. Removing Memory Module To remove a memory m odule, care fully pull the end clips outwards, then pull the memory module out of the socket.
Options ADVANCED OPERAT ION GUIDE 4-15 HDD Security Function Data Security Kit( C) has the fu nctions of ov erwriting an d encryption. NOTE: T o use the HDD Security featur e, an option hard disk and the Data Secu rity Kit (C) need to be p re- installed.
Options 4-16 ADVANCED OPERATION GUIDE Encryption Function The printer temporarily store s print jobs on an internal hard disk. If the hard disk is stolen, there is a risk th at th e data might be passed to unauthorized parties or modified. The Security Kit encrypts data before stori ng data on the hard disk.
Options ADVANCED OPERAT ION GUIDE 4-17 6 Press U or V to display the desired mode. The display chan ges as shown below. Normal (default) : Overwrites 3 time s. (Overwrites 2 times with random data, then 1 more time with NULL data.) Quick : Overwrites 1 time.
Options 4-18 ADVANCED OPERATION GUIDE.
ADVANCED OPERATION GUIDE 5-1 5 Computer Interface This chapter contains explanat ions on the following topics: • General Information..... ......................................... ....... 5-2 • Parallel Interface ........ .........................
Computer Interface 5-2 ADVANCED OPERATION GUIDE General Information This chapter explains th e signals us ed in the printer's parallel, USB, and serial (option) interfaces. It also lis ts pin assignments, signal functions, timings, connector specifications, and voltage le vels.
Computer Interface ADVANCED OPERATION GUIDE 5-3 Parallel Interface Communication Modes The printer features fast data transmission with th e parallel interface. The parallel interface mode can be activated from the operation panel. Refer to Changing Parallel Interface Modes on page 2-35 .
Computer Interface 5-4 ADVANCED OPERATION GUIDE * Indicates signals that are low active. ** The Paper Empty , Online, and Err or signals work only af ter you have enabled them using the O2 parameter of the FRPO comman d. 10 Out Acknowledge* [n Ack] This negative-going pu lse acknowledges the previous character received.
Computer Interface ADVANCED OPERATION GUIDE 5-5 USB Interface This printer supports th e Hi-Speed USB (Universal Serial Bus) interface specifications and interface signals ar e as follows.
Computer Interface 5-6 ADVANCED OPERATION GUIDE Serial Interface (Option) Interface Signals The pins of the printer’s RS-2 32C interface connector carry th e signals listed in the table below. The table al so indicates whether each signal is incoming or outgoing with r espect to the printer.
Computer Interface ADVANCED OPERATION GUIDE 5-7 RS-232C Protocol Parameters of the RS-232C Protocol A protocol is a set of rules the computer follows in se nding data to the printer. They are indicate d on the status page. Par ameters can be changed from the operation pa nel.
Computer Interface 5-8 ADVANCED OPERATION GUIDE H4: Parity The factory default setting is No ne ( 0 on the status printout). H5: Protocol logic The factory default setting is 0. H6: Buffer nearly -full threshold This is a percentage from 0 to 99. The factory default setting is 90.
Computer Interface ADVANCED OPERATION GUIDE 5-9 PRESCRIBE FRPO D0 command The PRESCRIBE FRPO D0 command pr ovides control over XON/XOFF operation wh en an error occurs on t he serial inte rface. The following table summarizes the error status corresponding to d ifferent D0 values.
Computer Interface 5-10 ADVANCED OPERATION GUIDE RS-232C Cable Connection Connecting the Printe r to the Computer Check that the power of both the printe r and the co mputer is switched off. 1 Discharge yourself of static electricity by touching a metal o bject suc h as a doorknob.
Computer Interface ADVANCED OPERAT ION GUIDE 5-11 3 System Properties window opens. Click on the Hardware tab, then click on the Device M anager button, and double click on Ports (COM & LPT) . 4 Double click on Communications Port . 5 The Communications Port Properties dialo g is displayed for the selected COM port.
Computer Interface 5-12 ADVANCED OPERATION GUIDE 3 System Properties opens. Click on the Device Mana ger tab, then click on the COM port to be used. 4 Click on the Properties button. 5 The Properties sheet is displayed for the selected COM po rt. Click on the Port Settings tab and set the port properties.
ADVANCED OPERATION GUIDE Glossary-1 Glossary AppleTalk AppleTalk offers file sharing and printe r sh aring and it also enables you to utilize application software that is on anothe r computer on the same AppleTalk netw ork.
Glossary-2 ADVANCED OPERATION GUIDE KIR (Kyocera Image Refinement) This is Kyocera Mita’s original smoot hing function. It uses soft ware to enhance the printer’s resolu tion and produce high-q uality printing. The default setting is On. KPDL KPDL is Kyocera’s implementation of the PostScript page descr iption language Level3.
ADVANCED OPERATION GUIDE Index-1 Index A Access code 2-26 , 2-27 Adhesive label 1- 10 Alarm (buzzer) how to set 2-92 Auto error clear changing recovery time 2-94 how to set 2-93 Automatic manual feedi.
Index-2 ADVANCED OPERATION GUIDE Finishing duplex printing error detection 2-95 punch error detection 2-97 staple error detection 2-96 Font adjusting character pi tch for fixed fonts 2-48 changing the.
ADVANCED OPERATION GUIDE Index-3 N Network interface a sample of the ne twork status page 2-41 installing interface cards 4-6 printing a network status page 2-40 protocols and parameters 2-37 Number o.
Index-4 ADVANCED OPERATION GUIDE Specifications paper 1-3 Status page how to print 2-20 understanding 2-21 Storage device deleting data 2-65 printing a list of partitions 2-67 reading/writing data 2-6.
A1.
.
is a trademark of Kyocera Corporation 2006.
Rev. 1.0 2006.4.
Ein wichtiger Punkt beim Kauf des Geräts Kyocera FS 9530DN (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kyocera FS 9530DN noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kyocera FS 9530DN - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kyocera FS 9530DN reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kyocera FS 9530DN erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kyocera FS 9530DN besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kyocera FS 9530DN verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kyocera FS 9530DN. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kyocera FS 9530DN gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
