Benutzeranleitung / Produktwartung E1660Sw des Produzenten AOC
Zur Seite of 59
.
2 Safety ............................................................................................................................... ......................................... 4 National C onventio ns ...........................................
3 EPEA T Declar ation ............................................................................................................. ............................. 5 4 Service .........................................................................
4 Safety National Conventions The following subsections desc ribe n otational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text ma y be accompanied by an icon and printe d in bold type or in italic type.
5 Power The monitor should be operat ed only from the type of power source indicated on the lab el . If you are not sure of the type of power supplied to your hom e, consu lt your dealer or local power company . The monitor is equipped with a three-pronged grounded plug, a plu g with a third (grounding) pin.
6 Inst allation Do not place the monitor on a n unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
7 Cleaning Clean the cabinet regularly with cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the pro duct cabi net. When cleaning, make sure no detergent is leaked into the product. T he cleaning cloth should not be too r ough as it will scratch the screen surface.
8 Other If the product is emitting a strange smell, sound or smoke, disconnect the po wer plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating ope nin gs are not blocked by a table or curtain. Do not engage the LCD monitor in severe vib ration or high impact conditions during operation.
9 Setup Content s in Box Monitor CD Manual S tand Base Power C able Analog Cable.
10 Setup S t and & Base Please setup or remove the base follo wing the step s as below . Setup: Remove:.
11 Adjusting V iewing Angle For optimal viewing it is recommended to look at the full fa ce of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not toppl e the mon i tor when you change the monitor's angl e.
12 Connecting the Monitor Cable Connections In Back of Monitor an d Computer: 1. Power 2. Analog (DB-15 VGA cable) T o protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the po wer cable to the AC port on the back of the monitor .
13 W all Mounting Preparing to Install An Optional Wa ll Mountin g Arm. This monitor can be attached to a wall mounting arm you p urchase separately . Disconnect po wer before this procedure. Follow these steps: 1 Remove the base. 2 Follow the manufacturer's instructi ons to assemble the wall mounting arm.
14 Adjusting Setting Optimal Resolution Windows Vist a For Window s Vista: 1 Click ST ART . 2 Click CONTROL P ANEL. 3 Click Appearance and Pers onalization.
15 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1366 by 768..
16 Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y ..
17 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1366 by 768. Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1366 by 768 .
18 Hotkeys 1 Auto/Exit 2 </ECO 3 >/Image Ratio 4 Menu/Enter 5 Power Power Press the Power button to turn on/off the monitor . Menu/Enter When the OSD is closed, press Source button will be Source hot ke y function.
19 OSD Setting Basic and simple instruction o n the control keys. 1) Press the MENU-button to activate the OSD window . 2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the ME NU-button to activate it .
20 Luminance 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Luminance), and press to enter. 3 Press 〈 or 〉 to select submenu, and press to enter .
21 4 Press 〈 or 〉 to adjust. 5 Press to exit . Brightness 0-100 Backlight Adju stment Contrast 0-100 Contra st from Digital-register. Eco mode Standard Standard Mode Tex t Text Mode Internet Inter.
22 Image Setup 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Image Setup), and press to enter . 3 Press 〈 or 〉 to select submenu, and press to enter .
23 4 Press 〈 or 〉 to adjust. 5 Press to exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Lin e nois e. Phase 0-100 Adjust Picture Phas e to reduce Horiz ontal-Line noise Sharpness 0-100 Adjust picture sharpness H.Position 0-100 Adjust the hori zontal position of the picture.
24 Color Setup 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Color Setup), and press to enter . 3 Press 〈 or 〉 to select submenu, and press to enter .
25 4 Press 〈 or 〉 to adjust. 5 Press to exit . Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM.
26 Picture Boost 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Picture Boost), and press to enter . 3 Press 〈 or 〉 to select submenu, and press to enter .
27 4 Press 〈 or 〉 to adjust. 5 Press to exit . Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H.
28 OSD Setup 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (OSD Setup), and press to enter . 3 Press 〈 or 〉 to select submenu, and press to enter .
29 4 Press 〈 or 〉 to adjust. 5 Press to exit . H.Position 0-100 Adjust the horizontal posit ion of OSD V.Position 0-100 Adjust t he verti cal pos ition of OSD Timeout 5-120 Adjust the OSD Timeout .
30 Extra 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Extra), and press to enter . 3 Press 〈 or 〉 to select submenu, and press to enter .
31 4 Press 〈 or 〉 to adjust. 5 Press to exit . Auto /Analog Auto /Analog Select Input Signal Source Auto Config yes or no Auto adjust the picture to default Off timer 0-24hrs Select DC off time Im.
32 Exit 1 Press (Menu) to display menu. 2 Press 〈 or 〉 to select (Exit), and press to enter . 3 Press to exit Exit Exit the main OSD.
33 LED Indicator Stat us LED Color Full Power Mode Green or Blue Active-off Mode Orange or red.
34 Driver Monitor Driver Windows 7 1.S tart Windo ws® 7 2.Click on the 'St art' button and then click on 'Control Panel'. 3. Click on the 'Display' icon.
35 4.Ckick on the “Change display settings ” button. 5. Click the “ A dvanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
36 7.Click the “Driver” tab. 8. Open the "Update Driver Soft ware-Generi c PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer" .
37 10. Click the “Have Disk” button. Click on the “Brow se” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter desi gn ator for the CD -ROM drive). 11. Select the "xxx.inf" file and click the “Open” button.
38 Windows Vist a 1. Click "S tart " and "Control Pane l". Then, doubl e-click o n " Appearance and Personalization". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings.
39 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue".
40 Windows XP 1. S tart Windows® XP 2. Click on the 'S tart' button and t hen click on 'Control Panel'. 3. Select and click on the categor y ‘Appe arance and Themes’ 4.
41 5. Select the 'Settings' tab then click on the 'Advanced' butt on. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your m onitor is properly configur ed. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
42 8. Select the 'Install from a list or specific location [ advanced]' radio button and the n click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
43 Windows 2000 1. S tart Windows® 2000 2. Click on the 'S tart' button, point to 'S ettings', and then click on 'Control Pane l' . 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
44 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor disp lay setting by using on screen menus instead of the OSD button on the monitor .
45 e-Saver Welcome to use AOC e-Saver monitor po wer management software! The AOC e-Saver features Smart Shutdown functions for your monitors, all ows your monitor to timely shutdo wn when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your p references (see example below).
46 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window . Y ou only need to drag the window to a correspondi ng pane, when you want to access it.
47 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure th e power button is ON and the Power Cor d is properly connected to a grounded power outlet and to the monitor . No images on the screen Is the power cord connected properly? Check the power cord connection and po wer supply .
48 Monitor Is Stu ck In A ctive Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor's video cable is prop erly connected to the computer . Inspect the monitor's video cable and mak e sure no pin is bent.
49 S pecification General S pecification Panel Model name E 1660S w Driving system TFT Color LCD Viewable Image Size 39.5 cm diagonal Pixel pitch 0.252 mm (H) x 0. 252 mm (V) Video R, G , B Analog lnterface Separate Sy nc. H/V TTL Display Color 262,144 Colors Dot Clock 85.
50 Preset Display Modes ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHz) V ERTICAL FREQUENCY(Hz) Dos-mode 720 x 400 31.47 70 VGA 640 x 480 31.47 60 SVGA 800 x 600 37.
51 Pin Assignment s Pin Number 15-Pin Side of the Signal Cabl e 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.
52 Regulation FCC Notice FCC Class B Radio Freq u ency Interference St at ement W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to compl y with the limits for a Class B digit al device, pursuant to Part 15 of the FCC Rules.
53 WEEE Declaration Disposal of W aste Equipment by Users in Pr ivate Household in the Europe an Un ion. This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household wast e.
5 4 E P E AT Declaration EPEA T is a syst em to help p urchasers in the publ ic and priv ate sector s evaluate , compare and select desktop computers, n otebooks a nd monitor s based on t heir enviro nmental attr ibutes.
5 5 Service W arranty St atement for Europe LIMITED THREE-YEAR W ARRANTY* AOC Color Monitors sold within Europe AOC International (Europe) BV warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of c onsumer purchase.
5 6 modified or altered; you bear the sole responsibility and liabilit y for any such modification or alteration. ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERC.
5 7 W arranty St atement for North & South America (excluding Brazil) W ARRANTY ST A TEMENT for AOC Color Monitors Including those Sold within North America as S pecified Envision Peripherals, Inc.
5 8 ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FIT NESS FOR A P ARTICULAR PURPOSE) ARE LIMIT ED IN DURA T ION TO A PERIOD OF THREE (3) YEA RS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CR T TUBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
WARRANTY PERIOD COVERAGE AT NO CHARGE CUSTOMER CHARGES Within the first three months of purchase: Covered by EASE - New AOC monitor - Call tag dispatched and return freight charges via UPS - None* Bet.
Ein wichtiger Punkt beim Kauf des Geräts AOC E1660Sw (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AOC E1660Sw noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AOC E1660Sw - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AOC E1660Sw reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AOC E1660Sw erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AOC E1660Sw besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AOC E1660Sw verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AOC E1660Sw. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AOC E1660Sw gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
