Benutzeranleitung / Produktwartung 7176-000-090-500 des Produzenten Kettler
Zur Seite of 28
Match 5.0 T able T ennis T able Models 7136-000-500 & 7176-000- 090- 500 Printed on recycled paper . Made in Germany Picture Similar KETTLER ® International Inc. • 1355 London Bridge Road • Virginia Beach, V A 23453 USA www .kettlerusa.com info@kettlerusa.
Note on Safety All KETTLER ® products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products.
Before Assembly (continued) General Assembly Instructions • The equipment must be assembled with care by two adults. • Separate all the parts including the hardware. Compare quantities with the package contents section and that all items are undamaged.
Items below are shown at actual size Number Incl. - 1-6mm, 2-8mm Number Incl. - 2 (outdoor only) Number Included - 2 Number Included - 2 Number Included - 1 Number Included - 1 Number Included - 2 Num.
Package Contents (continued) Items below are shown at actual size Number Included - 18 m6 Number Included - 2 Number Included - 8 m8 Number Included - 8 Number Included - 4 Number Included - 8 m12x6x3.
Assembly Begin the assembly of your table by carefully removing the plastic wrap and all of the loose contents. Separate the two table tops by removing the four plastic corner protectors and the plastic side strips. Step 1 2 Required Align footlock with stemtube.
Assembly Step 2 A B C D E F 4 Required 4 Required m8 8 Required dia 16x8 4 Required m8x125 4 Required dia 25x8 8 Required End view and perspective view 4 Required Paying attention to position of wheelbase, assemble the stemtubes to base in order shown.
J K L Assembly Step 2 (continued) G H I Photo K shows the non locking stemtube being installed. Step E to step J are the same for the locking and non locking stemtube.
Step 3 Assembly Install non-locking wheels. Do not over torque; wheels should roll smoothly . Install non-locking wheels on both wheelbase assemblies. A B C D E 2 Required m8x1 10 8 Required dia 16x8 .
Step 4 Assembly Install locking wheels. The grooves of wheels should face inward. Again, do not over torque; wheels should roll smoothly . Push down foot lock to lock the wheels.
Assembly Step 5 Paying attention to position of wheelbase, snap alignment struts into place. Bolt locking struts to base. Bolt the locking strut with thumb latch to the same side as locking wheels. Bolt strut without latch to the side of non-locking wheels.
Assembly Step 6 Bolt one M8 crossbar between each wheelbase. This crossbar is being assembled temporarily to create a support base and will be removed at a later step. For outdoor tables only: slide the shimpad onto wheelbase (steps B, C, and D). The assembly thus far should match photo E.
Assembly Step 7 Insert endcap into the bottom of netpost bar . Using M6 crossbar , assemble crossbar and netpost bars to alignment struts. The netpost bar installation is repeated on the other wheelbase assembly . Fastener quantities include installation on both wheelbase assemblies.
Assembly Step 8 Screw eyelets to four Jbars. Assemble safety levers to two of the Jbars. Slide handgrip onto safety lever . Note the orientation of the slot in the safety lever and the Jbar as shown in photo E. 4 Required dia 12x6 2 Required m6 4 Required 2 Required m6x30 2 Required A B C D E F G 4 Required 3.
Assembly Step 9 Screw eyelets to support leg on table-top half. Repeat for second table-top half. 4 Required A B C 4 Required 3.9x13 Support Leg 15.
A B C D Step 10 Important: have two people complete steps 10-12. With assistance, lift one table top onto the wheelbase; the legs will be facing outward. Have one person support the top while it is resting on the base while the other completes assembly .
A B C D Step 11 Raise safety lever up straight. Bolt the safety lever to leg. Bolt the Jbars to leg. Insert footcaps. E F Assembly 1 Required m6x37 2 Required dia 12x6 3 Required m6 1 Required m 16x8x.
Step 11 continued Assembly J K L Leg Step 12 Bolt locking struts to support leg. A B C D E F G 2 Required m6x49 2 Required m6 4 Required m12x6 18 Now , remove the temporary crossbar assembled in step 6.
Assembly 19 A B C D T o properly open table into playing position: lock wheels (H), push the thumb latch down on the left locking strut. Squeeze the strut on the right side and lower table into playing position. Support the table as you lower it; never allow it to drop down.
A C D Step 13 Slide net post onto netpost bar and screw into place. Insert guide plug. Repeat on other side of table. Assembly 2 Required 4.8x25 2 Required A B Step 14 Attach ball/racquet holder to netpost.
A B Step 15 Screw sideshroud into place. Repeat installation of second shroud on opposite side wheelbase assembly . Assembly 6 Required 3.9x25 21 3 Screws.
Assembly Net Assembly Net assembly: Slide Jpin through net.. Place Jpin in designated slots. T ie string to tension tab. Place string in slots over Jpin and net post. Adjust net tension by adjusting tension tab. Remove protective plastic film from table surface.
Assembly 23 Folding T able Folding T able: T o properly fold the table, lock the wheels, press the safety lever up and lift top. Once the top is halfway up you can release lever and continue to fold the top. A B C Remove Film Remove protective plastic film from table surface.
THERE ARE NO W ARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANUF ACTURER ON KETTLER ® PRODUCTS, EXCEPT THE MANUF ACTURER’S LIMITED W ARRANTY AGAINST DEFECTS IN MA TERIAL .
25 Ordering Spare Parts When ordering spare parts, always state the full model number , spare part number , the quantity required and the serial number . Example order: Model 7136-500/spare part number 70130761/qty 1/serial number… Important: Spare part prices do not include fastening materials; if fastening material (bolts, nuts, washers, etc.
12 1 25 13 17 4 4 7 2 3 23 25 22 8 10 11 19 29 28 30 32 27 15 20 21 31 25 12 1 25 33 33 13 17 6 5 2 3 7 23 9 37 34 26 35 36 38 Spare Parts 26.
Spare Parts 1 T op 2 941301 17 94130125 2 Leg 2 941 1 1 138 941 1 1 129 3 Footcap 4 70130540 70130540 4 Clamp (outdoor table) 8 10128028 5 Clamp 25mm (indoor table) 4 941 10341 6 Clamp 18mm (indoor ta.
KETTLER ® International Inc., 1355 London Bridge Road, Virginia Beach, V A 23453 USA www .kettlerusa.com • E-mail: info@kettlerusa.com For parts/service: call 866-804-0440 or e-mail parts@kettlerusa.com Docu 7 . 05 .1 1 ©201 1 KETTLER ® All rights reserved.
Ein wichtiger Punkt beim Kauf des Geräts Kettler 7176-000-090-500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kettler 7176-000-090-500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kettler 7176-000-090-500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kettler 7176-000-090-500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kettler 7176-000-090-500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kettler 7176-000-090-500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kettler 7176-000-090-500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kettler 7176-000-090-500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kettler 7176-000-090-500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
