Benutzeranleitung / Produktwartung RX-D701S des Produzenten JVC
Zur Seite of 234
LVT1437-012A [A] RX-D701S A UDIO/VIDEO CONTR OL RECEIVER INSTR UCTIONS cover_RX-D701S[A]_f.p65 05.9.23, 11:05 AM 3.
RX-D701S W arnings, Cautions, and Others Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.
1 Intr oduction We would like to thank y ou for purchasing one of our JVC products. Before operating this unit, read this man ual carefully and thoroughly to obtain the best possible performance from y our unit, and retain this manual f or future ref erence.
2 Ta b le of Contents Pa r ts identification ................................................ 3 Getting started ...................................................... 6 Before Installation ..............................................................
3 A/V CONTROL RECEIVER REMOTE CONTROL RM - SRXD701U TV/VIDEO A UDIO TV DBS/CA TV DVR/D VD AM AUX VCR TV DBS D VR/DVD USB VCR TV VOL CHANNEL V OLUME FM MODE MUTING MEMORY TUNING/REW FF/TUNING SETTING D VD MENU DECODE MODE MIDNIGHT D .EQ FREQ D .EQ LEVEL C.
4 Front panel 1 ST ANDBY/ON button and standby lamp (19) 2 CC CONVERTER b utton (22) 3 SETTING button (25, 27) 4 ADJUST button (33, 35) 5 SURROUND b utton (45) 6 HDMI lamp (9, 20) 7 Source lamps (19) .
5 1 Po wer cord (16) 2 HDMI terminals (10, 11, 13, 14) VCR(DBS) IN, D VR/D VD IN, MONIT OR OUT 3 AV COMPU LINK- III ter minals (46) 4 DIGIT AL IN ter minals (16) • Coaxial: 1(D VR/D VD) • Optical:.
6 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–).
7 ANTENNA COAXIAL FM 75 AM EXT AM LOOP ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed.
8 FL FR SL SR SBL C SW SBR (*SB) SUBWOOFER OUT LEFT RIGHT LEFT RIGHT LEFT RIGHT CAUTION:SPEAKER IMPEDANCE 6 - 16 FRONT SPEAKERS CENTER SPEAKER SURROUND BACK SPEAKERS SURROUND SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed.
9 Connecting video components Do not connect the A C power plug to the wall outlet until all connections are completed. Video conversion function This receiv er can conv er t the video signals output from video components. The char t below sho ws which video signals can be con v erted into which signals by video con version.
10 Åı Î Ç MONITOR OUT ‰ Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN TV IN D B I N L R MONITOR OUT / DVD P LAY) Select the appropriate VIDEO OUTPUT (see page 32) according to the terminal used f or TV connection referring to the table belo w.
11 ) IN DVR/DVD IN HDMI ı Ή Ï Ì Ç Å Ó DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT 7 Connecting a D VD recor.
12 Å Ï Ó ı Ç Î ‰ Ì Ô DVR OUT(REC) DVR/DVD IN(PLAY) DVR OUT(REC) DVR/DVD IN(PLAY) FRONT COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVD MULTI IN CENTER SUBWOOFER SURR-L SURR-R È Y P B.
13 VCR OUT(REC) IN(PLAY) AUDIO OUT(REC) IN(PLAY) VCR VCR(DBS) IN HDMI Å ı Ή Ï Ì Ç Ó Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Å Do not connect the A C power plug to the wall outlet until all connections are completed.
14 COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Y P B P R O U VIDEO DBS IN VIDEO S-VIDEO DBS IN O U VCR(DBS) IN H D Åı Î Ç ‰ Do not connect the A C power plug to the wall outlet until all connections are completed.
15 7 Connecting a video component to the A UX input jacks The A UX input jacks on the front panel (inside the front door) are conv enient when connecting and disconnecting the component frequently . Before making connections , press PUSH-OPEN to show the jacks .
16 DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals on the rear of the receiver ha ve been set for use with the f ollo.
17 USB USB connection This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA ter minal on the rear . Y ou can enjoy the sound reproduced through y our PC with eith.
18 Now PC is read y for pla yback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recogniz es the receiver whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiv er is turned on.
19 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the displa y . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as f ollo ws: D VR/D VD: Select this f or the D VD recorder or D VD play er.
20 NO TES • “HDMI” is availab le only for the source with “HDMI” selected in the video input setting (see the left column). • “DIGIT AL ” is a vailab le for the source assigned f or “DIGIT AL IN 1, ” “DIGIT AL IN 2, ” or “DIGIT AL IN 3.
21 Selecting the digital decode mode This receiver automatically detects the incoming digital signal for mat when “HDMI” or “DIGIT AL ” is selected in the audio input setting (see page 20).
22 Basic adjustment of auto memory This receiv er memorizes sound settings for each source: • when you turn off the power , and • when you change the source . When you change the source , the memorized settings f or the newly selected source are automatically recalled.
23 To obtain the best possib le sound effect from Surround/DSP modes (see pages 41 to 45), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 23 to 32, how to set speakers and other basic items of the receiv er are explained.
24 When your c lapping sound is detected successfully • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 10 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as f ollows f or about 10 seconds: Ex.
25 Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. For e xample, when “S BA CK SPK” is set to “S BACK SPK: NO, ” you cannot select the follo wing items: S BACK OUT , SB SPK DIST .
26 SURROUND BACK SPEAKER SURROUND SPEAKER CENTER SPEAKER FRONT SPEAKER FR SPK DISTANCE SURROUND BACK OUT FL SPK DISTANCE SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR SPK : SMALL S BACK SPK : SMALL S BACK OUT : 2SPK ∞ :ENTER :EXIT SETTING MENU (2) 5 DISTANCE UNIT : meter FL SPK DIST .
27 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
28 DIGITAL IN 1 DIGITAL IN 1 : 2 DVR/DVD 3 DVR/DVD DBS VCR TV 3 Press SET . 4 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . I n this e xample, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN 1” appears on the displa y .
29 In this case, set the distance as f ollows: Left front speaker (FL): “FL SPK DIST .: 3.0m (10ft)” Right front speaker (FR): “FR SPK DIST .: 3.0m (10ft)” Center speaker (C): “C SPK DIST .: 3.0m (10ft)” Left surround speaker (SL): “SL SPK DIST .
30 Selecting the main or sub channel —DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 42), which includes two monaural channels separately . When the receiver detects Dual mono signals , the DU AL MONO indicator lights up on the displa y .
31 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 16) so that the correct source name will appear when y ou select the digital source.
32 Selecting the output video signals —VIDEO OUTPUT To use the video conv ersion function (see page 9), you need to select this setting according to the connection method f or a TV . VIDEO OUTPUT : HDMI Select this when connecting a TV with the HDMI cable.
33 Sound adjustments Y ou can make sound adjustment to y our pref erence after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting.
34 DIGITAL EQ 250Hz ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR L LEVEL : 0 SURR R LEVEL : 0 S BACK L LEVEL : 0 S BACK R LEVEL : 0 ∞ :ENTER :EXIT .
35 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
36 From the remote control: 1 Press TEST to check the speaker s’ output balance . • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the speakers . EX.: • On the displa y , “TEST L ” star ts flashing, and a test tone comes out of the speakers cloc kwise.
37 7 Attenuating the input signal—INPUT A TT When the input lev el of analog source is too high, the sound will be distor ted. If this happens, you need to atten uate the input signal lev el to prev ent the sound distor tion. • Once you hav e made an adjustment, it is memorized for each source.
38 7 Adjusting the sound localization of the center channel—CENTER GAIN This setting is av ailable only when Neo:6 Music is in use. • If “CENTER SPK” is set to “NO” (see page 28), this item is not adjustable. • Once you hav e made an adjustment, it is memorized until you change the setting.
39 T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in.
40 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10.
41 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed.
42 DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software b y using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the follo wing DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
43 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls.
44 Using the Surround/DSP modes Av ailable Surround/DSP modes v ary depending on the speaker settings and the incoming signals. See the tab le below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels.
45 On the front panel: Before y ou star t, remember... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again.
46 AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD player*, and VCR) through this receiver .
47 One-touch DVD play Simply by starting playbac k on the D VD player , you can enjo y the D VD playback without setting other s witches manually . The follo wing is set automatically: •T ur ning on the receiver . • Changing the source to “D VR/D VD .
48 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals—remote codes “A” and “B.
49 Y ou can alwa ys perform the following operation: D VR/D VD : Tu rn on or off the D VD recorder or D VD play er. After pressing D VR/D VD , you can perf or m the f ollowing operations on the D VD recorder and D VD player . 3 : Star t playbac k. 7 : Stop pla yback.
50 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Refer also to the man uals supplied with the other products.
51 ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR.
52 Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S.
53 Tr oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solve, contact y our JVC’ s service center. PROBLEM The power does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the displa y , then the receiver turns off.
54 PROBLEM Remote control does not operate as y ou intend. Remote control does not work. Continuous hiss or buzzing during FM reception. Occasional crac king noise during FM reception. POSSIBLE CA USE The remote control is not ready f or your intended operation.
55 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 130 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% total harmonic distor tion (IEC268-3/DIN). At surround operation: F ront channels: 130 W per channel, min.
1105RYMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D701S cover_RX-D701S[A]_f.p65 05.11.1, 1:30 PM 2.
LVT1437-007A [J] RX-D702B A UDIO/VIDEO CONTR OL RECEIVER INSTR UCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No.
W arnings, Cautions, and Others Mises en gar de , précautions et indications diverses Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line.
1 Intr oduction We would like to thank y ou for purchasing one of our JVC products . Before operating this unit, read this man ual carefully and thoroughly to obtain the best possible performance from y our unit, and retain this manual f or future ref erence.
2 Ta b le of Contents Pa r ts identification ................................................ 3 Getting started ...................................................... 6 Before Installation ..............................................................
3 A/V CONTROL RECEIVER REMOTE CONTROL RM - SRXD701J TV/VIDEO A UDIO TV/SIRIUS DBS/CA TV DVR/D VD FM/AM AUX VCR TV DBS D VR/DVD USB VCR TV VOL CHANNEL VOLUME FM MODE MUTING MEMORY TUNING/REW FF/TUNING SETTING D VD MENU DECODE MODE MIDNIGHT D .EQ FREQ D .
4 AUDIO/VIDEO CONTROL RECEIVER STANDBY/ON CC CONVERTER SETTING ADJUST SURROUND DVR / DVD VCR DBS TV/SIRIUS USB FM/AM SOURCE SELECTOR / MULTI JOG MASTER VOLUME SET / TUNER PRESET AUX HDMI PUSH-OPEN 45 .
5 1 Po wer cord (16) 2 HDMI terminals (10, 11, 13, 14) VCR(DBS) IN, D VR/D VD IN, MONIT OR OUT 3 AV COMPU LINK- III ter minals (46) 4 DIGIT AL IN ter minals (16) • Coaxial: 1(D VR/D VD) • Optical:.
6 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–).
7 ANTENNA COAXIAL FM 75 AM EXT AM LOOP ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed.
8 FL FR SL SR SBL C SW SBR (*SB) SUBWOOFER OUT LEFT RIGHT LEFT RIGHT LEFT RIGHT CAUTION:SPEAKER IMPEDANCE 6 - 16 FRONT SPEAKERS CENTER SPEAKER SURROUND BACK SPEAKERS SURROUND SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed.
9 Connecting audio and video components Do not connect the A C power plug to the wall outlet until all connections are completed. Video conversion function This receiv er can conv er t the video signals output from video components. The char t below sho ws which video signals can be con v erted into which signals by video con version.
10 Åı Î Ç MONITOR OUT ‰ Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN TV/SIRIUS IN D B I N L R MONITOR OUT / DVD P LAY) Select the appropriate VIDEO OUTPUT (see page 32) according to the terminal used f or TV connection referring to the table belo w .
11 ) IN DVR/DVD IN HDMI ı Ή Ï Ì Ç Å Ó DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT 7 Connecting a D VD recor.
12 Å Ï Ó ı Ç Î ‰ Ì Ô DVR OUT(REC) DVR/DVD IN(PLAY) DVR OUT(REC) DVR/DVD IN(PLAY) FRONT COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVD MULTI IN CENTER SUBWOOFER SURR-L SURR-R È Y P B.
13 VCR OUT(REC) IN(PLAY) AUDIO OUT(REC) IN(PLAY) VCR VCR(DBS) IN HDMI Å ı Ή Ï Ì Ç Ó Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Å Do not connect the A C power plug to the wall outlet until all connections are completed.
14 Do not connect the A C power plug to the wall outlet until all connections are completed. 7 Connecting a DBS tuner: Stereo audio cable (not supplied) White Component video cable (not supplied) Comp.
15 TV/SIRIUS IN D B I N L R 2 5 ∞ 3 7 Connecting a video component to the A UX input jacks The A UX input jacks on the front panel (inside the front door) are conv enient when connecting and disconnecting the component frequently . Before making connections , press PUSH-OPEN to show the jacks .
16 DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals on the rear of the receiver ha ve been set for use with the f ollo.
17 USB connection This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA ter minal on the rear . Y ou can enjoy the sound reproduced through y our PC with either o.
18 Now PC is read y for pla yback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recogniz es the receiver whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiv er is turned on.
19 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the displa y . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as f ollo ws: D VR/D VD: Select this f or the D VD recorder or D VD play er.
20 NO TES • “HDMI” is availab le only for the source with “HDMI” selected in the video input setting (see the left column). • “DIGIT AL ” is a vailab le for the source assigned f or “DIGIT AL IN 1, ” “DIGIT AL IN 2, ” or “DIGIT AL IN 3.
21 Selecting the digital decode mode This receiver automatically detects the incoming digital signal for mat when “HDMI” or “DIGIT AL ” is selected in the audio input setting (see page 20).
22 Basic adjustment of auto memory This receiv er memorizes sound settings for each source: • when you turn off the power , and • when you change the source . When you change the source , the memorized settings f or the newly selected source are automatically recalled.
23 To obtain the best possib le sound effect from Surround/DSP modes (see pages 41 to 45), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 23 to 32, how to set speakers and other basic items of the receiv er are explained.
24 When your c lapping sound is detected successfully • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 10 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as f ollows f or about 10 seconds: Ex.
25 Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. For e xample, when “S BA CK SPK” is set to “S BACK SPK: NO, ” you cannot select the follo wing items: S BACK OUT , SB SPK DIST .
26 SURROUND BACK SPEAKER SURROUND SPEAKER CENTER SPEAKER FRONT SPEAKER FR SPK DISTANCE SURROUND BACK OUT FL SPK DISTANCE SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR SPK : SMALL S BACK SPK : SMALL S BACK OUT : 2SPK ∞ :ENTER :EXIT SETTING MENU (2) 5 DISTANCE UNIT : meter FL SPK DIST .
27 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
28 DIGITAL IN 1 DIGITAL IN 1 : 2 DVR/DVD 3 DVR/DVD DBS VCR TV 3 Press SET . 4 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . I n this e xample, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN 1” appears on the displa y .
29 In this case, set the distance as f ollows: Left front speaker (FL): “FL SPK DIST .: 3.0m (10ft)” Right front speaker (FR): “FR SPK DIST .: 3.0m (10ft)” Center speaker (C): “C SPK DIST .: 3.0m (10ft)” Left surround speaker (SL): “SL SPK DIST .
30 Selecting the main or sub channel —DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 42), which includes two monaural channels separately . When the receiver detects Dual mono signals , the DU AL MONO indicator lights up on the displa y .
31 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 16) so that the correct source name will appear when y ou select the digital source.
32 Selecting the output video signals —VIDEO OUTPUT To use the video conv ersion function (see page 9), you need to select this setting according to the connection method f or a TV . VIDEO OUTPUT : HDMI Select this when connecting a TV with the HDMI cable.
33 Sound adjustments Y ou can make sound adjustment to y our pref erence after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting.
34 Setup menu configuration • Items on the menus shown belo w are all set to the initial v alues when shipped from the f actory . • Some of the menus or some items on the menu cannot be sho wn or cannot be adjusted depending on the current settings and the connections.
35 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
36 From the remote control: 1 Press TEST to check the speaker s’ output balance . • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the speakers . EX.: • On the displa y , “TEST L ” star ts flashing, and a test tone comes out of the speakers cloc kwise.
37 7 Attenuating the input signal—INPUT A TT When the input lev el of analog source is too high, the sound will be distor ted. If this happens, you need to atten uate the input signal lev el to prev ent the sound distor tion. • Once you hav e made an adjustment, it is memorized for each source.
38 7 Adjusting the sound localization of the center channel—CENTER GAIN This setting is av ailable only when Neo:6 Music is in use. • If “CENTER SPK” is set to “NO” (see page 28), this item is not adjustable. • Once you hav e made an adjustment, it is memorized until you change the setting.
39 T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM/AM to select the band. The last receiv ed station of the selected band is tuned in. • Each time y ou press the button, the band alternates between “FM” and “AM.
40 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10.
41 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed.
42 DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software b y using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the follo wing DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
43 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls.
44 Using the Surround/DSP modes Av ailable Surround/DSP modes v ary depending on the speaker settings and the incoming signals. See the tab le below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels.
45 On the front panel: Before y ou star t, remember... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again.
46 AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD player*, and VCR) through this receiver .
47 One-touch DVD play Simply by starting playbac k on the D VD player , you can enjo y the D VD playback without setting other s witches manually . The follo wing is set automatically: •T ur ning on the receiver . • Changing the source to “D VR/D VD .
48 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals—remote codes “A” and “B.
49 123 456 789 10 0 10 Y ou can alwa ys perform the following operation: D VR/D VD : Tu rn on or off the D VD recorder or D VD play er. After pressing D VR/D VD , you can perf or m the f ollowing operations on the D VD recorder and D VD player . 3 : Star t playbac k.
50 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Refer also to the man uals supplied with the other products.
51 ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR.
52 Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S.
53 Tr oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solve, contact y our JVC’ s service center. PROBLEM The power does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the displa y , then the receiver turns off.
54 PROBLEM Remote control does not operate as y ou intend. Remote control does not work. Continuous hiss or buzzing during FM reception. Occasional crac king noise during FM reception. POSSIBLE CA USE The remote control is not ready f or your intended operation.
55 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 150 W per channel, min. RMS, driven into 6 Ω at 20Hz to 20 kHz with no more than 0.8% total harmonic distortion. At surround operation: F ront channels: 150 W per channel, min.
warranty.p65 05.8.25, 1:20 PM 1.
warranty.p65 05.8.25, 1:20 PM 2.
0805RYMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D702B cover_RX-D702B[J]_f.p65 05.8.25, 1:20 PM 2.
English Français LVT1437-008A [C] INSTR UCTIONS MANUEL D’INSTR UCTIONS RX-D702B A UDIO / VIDEO CONTR OL RECEIVER RECEPTURE DE COMMANDE A UDIO/VIDEO cover_RX-D702B[C].
W arnings, Cautions, and Others Mises en gar de , précautions et indications diverses Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line.
1 English Intr oduction We would like to thank y ou for purchasing one of our JVC products . Before operating this unit, read this man ual carefully and thoroughly to obtain the best possible performance from y our unit, and retain this manual f or future ref erence.
2 English Ta b le of Contents Pa r ts identification ................................................ 3 Getting started ...................................................... 6 Before Installation ......................................................
3 English A/V CONTROL RECEIVER REMOTE CONTROL RM - SRXD701U TV/VIDEO A UDIO TV DBS/CA TV DVR/D VD AM AUX VCR TV DBS D VR/DVD USB VCR TV VOL CHANNEL VOLUME FM MODE MUTING MEMORY TUNING/REW FF/TUNING SETTING D VD MENU DECODE MODE MIDNIGHT D .EQ FREQ D .
4 English Front panel 1 ST ANDBY/ON button and standby lamp (19) 2 CC CONVERTER b utton (22) 3 SETTING button (25, 27) 4 ADJUST button (33, 35) 5 SURROUND b utton (45) 6 HDMI lamp (9, 20) 7 Source lam.
5 English 1 Po wer cord (16) 2 HDMI terminals (10, 11, 13, 14) VCR(DBS) IN, D VR/D VD IN, MONIT OR OUT 3 AV COMPU LINK- III ter minals (46) 4 DIGIT AL IN ter minals (16) • Coaxial: 1(D VR/D VD) • .
6 English Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–).
7 English ANTENNA COAXIAL FM 75 AM EXT AM LOOP ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed.
8 English FL FR SL SR SBL C SW SBR (*SB) SUBWOOFER OUT LEFT RIGHT LEFT RIGHT LEFT RIGHT CAUTION:SPEAKER IMPEDANCE 6 - 16 FRONT SPEAKERS CENTER SPEAKER SURROUND BACK SPEAKERS SURROUND SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed.
9 English Connecting video components Do not connect the A C power plug to the wall outlet until all connections are completed. Video conversion function This receiv er can conv er t the video signals output from video components. The char t below sho ws which video signals can be con v erted into which signals by video con version.
10 English Åı Î Ç MONITOR OUT ‰ Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN TV IN D B I N L R MONITOR OUT / DVD P LAY) Select the appropriate VIDEO OUTPUT (see page 32) according to the terminal used f or TV connection referring to the table belo w.
11 English ) IN DVR/DVD IN HDMI ı Ή Ï Ì Ç Å Ó DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT 7 Connecting a D .
12 English Å Ï Ó ı Ç Î ‰ Ì Ô DVR OUT(REC) DVR/DVD IN(PLAY) DVR OUT(REC) DVR/DVD IN(PLAY) FRONT COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVD MULTI IN CENTER SUBWOOFER SURR-L SURR-R .
13 English VCR OUT(REC) IN(PLAY) AUDIO OUT(REC) IN(PLAY) VCR VCR(DBS) IN HDMI Å ı Ή Ï Ì Ç Ó Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Å Do not connect the A C power plug to the wall outlet until all connections are completed.
14 English COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Y P B P R O U VIDEO DBS IN VIDEO S-VIDEO DBS IN O U VCR(DBS) IN H D Åı Î Ç ‰ Do not connect the A C power plug to the wall outlet until all connections are completed.
15 English 7 Connecting a video component to the A UX input jacks The A UX input jacks on the front panel (inside the front door) are conv enient when connecting and disconnecting the component frequently . Before making connections , press PUSH-OPEN to show the jacks .
16 English DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals on the rear of the receiver ha ve been set for use with th.
17 English USB USB connection This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA ter minal on the rear . Y ou can enjoy the sound reproduced through y our PC w.
18 English Now PC is read y for pla yback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recogniz es the receiver whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiv er is turned on.
19 English Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the displa y .
20 English NO TES • “HDMI” is availab le only for the source with “HDMI” selected in the video input setting (see the left column). • “DIGIT AL ” is a vailab le for the source assigned f or “DIGIT AL IN 1, ” “DIGIT AL IN 2, ” or “DIGIT AL IN 3.
21 English Selecting the digital decode mode This receiver automatically detects the incoming digital signal for mat when “HDMI” or “DIGIT AL ” is selected in the audio input setting (see page 20).
22 English Basic adjustment of auto memory This receiv er memorizes sound settings for each source: • when you turn off the power , and • when you change the source . When you change the source , the memorized settings f or the newly selected source are automatically recalled.
23 English To obtain the best possib le sound effect from Surround/DSP modes (see pages 41 to 45), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 23 to 32, how to set speakers and other basic items of the receiv er are explained.
24 English When your c lapping sound is detected successfully • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 10 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as f ollows f or about 10 seconds: Ex.
25 English Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. For e xample, when “S BA CK SPK” is set to “S BACK SPK: NO, ” you cannot select the follo wing items: S BACK OUT , SB SPK DIST .
26 English SURROUND BACK SPEAKER SURROUND SPEAKER CENTER SPEAKER FRONT SPEAKER FR SPK DISTANCE SURROUND BACK OUT FL SPK DISTANCE SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR SPK : SMALL S BACK SPK : SMALL S BACK OUT : 2SPK ∞ :ENTER :EXIT SETTING MENU (2) 5 DISTANCE UNIT : meter FL SPK DIST .
27 English Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
28 English DIGITAL IN 1 DIGITAL IN 1 : 2 DVR/DVD 3 DVR/DVD DBS VCR TV 3 Press SET . 4 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . I n this e xample, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN 1” appears on the displa y .
29 English In this case, set the distance as f ollows: Left front speaker (FL): “FL SPK DIST .: 3.0m (10ft)” Right front speaker (FR): “FR SPK DIST .: 3.0m (10ft)” Center speaker (C): “C SPK DIST .: 3.0m (10ft)” Left surround speaker (SL): “SL SPK DIST .
30 English Selecting the main or sub channel —DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 42), which includes two monaural channels separately .
31 English Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 16) so that the correct source name will appear when y ou select the digital source.
32 English Selecting the output video signals —VIDEO OUTPUT To use the video conv ersion function (see page 9), you need to select this setting according to the connection method f or a TV . VIDEO OUTPUT : HDMI Select this when connecting a TV with the HDMI cable.
33 English Sound adjustments Y ou can make sound adjustment to y our pref erence after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting.
34 English DIGITAL EQ 250Hz ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR L LEVEL : 0 SURR R LEVEL : 0 S BACK L LEVEL : 0 S BACK R LEVEL : 0 ∞ :ENTE.
35 English Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
36 English From the remote control: 1 Press TEST to check the speaker s’ output balance . • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the speakers . EX.: • On the displa y , “TEST L ” star ts flashing, and a test tone comes out of the speakers cloc kwise.
37 English 7 Attenuating the input signal—INPUT A TT When the input lev el of analog source is too high, the sound will be distor ted. If this happens, you need to atten uate the input signal lev el to prev ent the sound distor tion. • Once you hav e made an adjustment, it is memorized for each source.
38 English 7 Adjusting the sound localization of the center channel—CENTER GAIN This setting is av ailable only when Neo:6 Music is in use. • If “CENTER SPK” is set to “NO” (see page 28), this item is not adjustable. • Once you hav e made an adjustment, it is memorized until you change the setting.
39 English T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in.
40 English 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10.
41 English Creating realistic sound fields Reproducing theater ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed.
42 English DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software b y using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the follo wing DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
43 English Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls.
44 English Using the Surround/DSP modes Av ailable Surround/DSP modes v ary depending on the speaker settings and the incoming signals. See the tab le below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels.
45 English On the front panel: Before y ou star t, remember... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again.
46 English AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD player*, and VCR) through this receiver .
47 English One-touch DVD play Simply by starting playbac k on the D VD player , you can enjo y the D VD playback without setting other s witches manually . The follo wing is set automatically: •T ur ning on the receiver . • Changing the source to “D VR/D VD .
48 English Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals—remote codes “A” and “B.
49 English Y ou can alwa ys perform the following operation: D VR/D VD : Tu rn on or off the D VD recorder or D VD play er. After pressing D VR/D VD , you can perf or m the follo wing operations on the D VD recorder and D VD player . 3 : Star t playbac k.
50 English By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Refer also to the man uals supplied with the other products.
51 English ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR.
52 English Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S.
53 English Tr oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solve, contact y our JVC’ s service center. PROBLEM The power does not come on. The receiver turns off (enters standby mode).
54 English PROBLEM Remote control does not operate as y ou intend. Remote control does not work. Continuous hiss or buzzing during FM reception. Occasional crac king noise during FM reception. POSSIBLE CA USE The remote control is not ready f or your intended operation.
55 English Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 150 W per channel, min. RMS, driven into 6 Ω at 20Hz to 20 kHz with no more than 0.8% total harmonic distortion.
0905RYMMDWJEIN EN, FR © 2005 Victor Company of Japan, Limited cover_RX-D702B[C].p65 05.9.14, 1:40 PM 2.
LVT1437-009A [UJ] RX-D702B A UDIO / VIDEO CONTR OL RECEIVER INSTR UCTIONS cover_RX-D702B[UJ]_f.p65 05.9.9, 4:50 PM 3.
RX-D702B W arnings, Cautions, and Others Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.
1 Intr oduction We would like to thank y ou for purchasing one of our JVC products . Before operating this unit, read this man ual carefully and thoroughly to obtain the best possible performance from y our unit, and retain this manual f or future ref erence.
2 Ta b le of Contents Pa r ts identification ................................................ 3 Getting started ...................................................... 6 Before Installation ..............................................................
3 A/V CONTROL RECEIVER REMOTE CONTROL RM - SRXD701U TV/VIDEO A UDIO TV DBS/CA TV DVR/D VD AM AUX VCR TV DBS D VR/DVD USB VCR TV VOL CHANNEL VOLUME FM MODE MUTING MEMORY TUNING/REW FF/TUNING SETTING D VD MENU DECODE MODE MIDNIGHT D .EQ FREQ D .EQ LEVEL C.
4 Front panel 1 ST ANDBY/ON button and standby lamp (19) 2 CC CONVERTER b utton (22) 3 SETTING button (25, 27) 4 ADJUST button (33, 35) 5 SURROUND b utton (45) 6 HDMI lamp (9, 20) 7 Source lamps (19) .
5 1 Po wer cord (16) 2 VO LTA GE SELECT OR (6) 3 HDMI terminals (10, 11, 13, 14) VCR(DBS) IN, D VR/D VD IN, MONIT OR OUT 4 AV COMPU LINK- III ter minals (46) 5 DIGIT AL IN ter minals (16) • Coaxial:.
6 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–).
7 ANTENNA COAXIAL FM 75 AM EXT AM LOOP ANTENNA 110V 127V 220V 230 - 240V Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed.
8 FL FR SL SR SBL C SW SBR (*SB) SUBWOOFER OUT LEFT RIGHT LEFT RIGHT LEFT RIGHT CAUTION:SPEAKER IMPEDANCE 6 - 16 FRONT SPEAKERS CENTER SPEAKER SURROUND BACK SPEAKERS SURROUND SPEAKERS 110V 127V 220V 230 - 240V Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed.
9 Connecting video components Do not connect the A C power plug to the wall outlet until all connections are completed. Video conversion function This receiv er can conv er t the video signals output from video components. The char t below sho ws which video signals can be con v erted into which signals by video con version.
10 Åı Î Ç MONITOR OUT ‰ Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN TV IN D B I N L R MONITOR OUT / DVD P LAY) 110V 127V 220V 230 - 240V Select the appropriate VIDEO OUTPUT (see page 32) according to the terminal used f or TV connection referring to the table belo w.
11 ) IN DVR/DVD IN HDMI ı Ή Ï Ì Ç Å Ó DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT 110V 127V 220V 230 - 240V.
12 Å Ï Ó ı Ç Î ‰ Ì Ô DVR OUT(REC) DVR/DVD IN(PLAY) DVR OUT(REC) DVR/DVD IN(PLAY) FRONT COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVD MULTI IN CENTER SUBWOOFER SURR-L SURR-R È Y P B.
13 110V 127V 220V 230 - 240V VCR OUT(REC) IN(PLAY) AUDIO OUT(REC) IN(PLAY) VCR VCR(DBS) IN HDMI Å ı Ή Ï Ì Ç Ó Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Å Do not connect the A C power plug to the wall outlet until all connections are completed.
14 110V 127V 220V 230 - 240V COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Y P B P R O U VIDEO DBS IN VIDEO S-VIDEO DBS IN O U VCR(DBS) IN H D Åı Î Ç ‰ Do not connect the A C power plug to the wall outlet until all connections are completed.
15 7 Connecting a video component to the A UX input jacks The A UX input jacks on the front panel (inside the front door) are conv enient when connecting and disconnecting the component frequently . Before making connections , press PUSH-OPEN to show the jacks .
16 DIGITAL OUT PCM/STREAM 110V 127V 220V 230 - 240V 110V 127V 220V 230 - 240V DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actory , the DIGIT AL IN ter minals on the rear of.
17 USB USB connection This receiver is equipped with a USB terminal on the front panel and a USB WIRELESS ANTENNA ter minal on the rear . Y ou can enjoy the sound reproduced through y our PC with eith.
18 Now PC is read y for pla yback thr ough the USB connection. After installation is completed, you can use y our PC as the playbac k source. The PC automatically recogniz es the receiver whenev er the transmitter is connected to the PC or the USB cable is connected between the PC and the receiv er while the receiv er is turned on.
19 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the displa y . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as f ollo ws: D VR/D VD: Select this f or the D VD recorder or D VD play er.
20 NO TES • “HDMI” is availab le only for the source with “HDMI” selected in the video input setting (see the left column). • “DIGIT AL ” is a vailab le for the source assigned f or “DIGIT AL IN 1, ” “DIGIT AL IN 2, ” or “DIGIT AL IN 3.
21 Selecting the digital decode mode This receiver automatically detects the incoming digital signal for mat when “HDMI” or “DIGIT AL ” is selected in the audio input setting (see page 20).
22 Basic adjustment of auto memory This receiv er memorizes sound settings for each source: • when you turn off the power , and • when you change the source . When you change the source , the memorized settings f or the newly selected source are automatically recalled.
23 To obtain the best possib le sound effect from Surround/DSP modes (see pages 41 to 45), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 23 to 32, how to set speakers and other basic items of the receiv er are explained.
24 When your c lapping sound is detected successfully • On the TV screen, “SUCCESSFUL, ” “RESUL T , ” and the setting v alues appear . The setting values are shown f or about 10 seconds. Ex.: • On the display , “SUCCESSFUL ” appears, then the setting values are sho wn as f ollows f or about 10 seconds: Ex.
25 Basic setting items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting. For e xample, when “S BA CK SPK” is set to “S BACK SPK: NO, ” you cannot select the follo wing items: S BACK OUT , SB SPK DIST .
26 SURROUND BACK SPEAKER SURROUND SPEAKER CENTER SPEAKER FRONT SPEAKER FR SPK DISTANCE SURROUND BACK OUT FL SPK DISTANCE SETTING MENU (1) 5 SUBWOOFER : NO FRONT SPK : LARGE CENTER SPK : SMALL SURR SPK : SMALL S BACK SPK : SMALL S BACK OUT : 2SPK ∞ :ENTER :EXIT SETTING MENU (2) 5 DISTANCE UNIT : meter FL SPK DIST .
27 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
28 DIGITAL IN 1 DIGITAL IN 1 : 2 DVR/DVD 3 DVR/DVD DBS VCR TV 3 Press SET . 4 To select the appropriate setting, press 2 or 3 repeatedly , then press SET . The on-screen display returns to the pre vious SETTING MENU . I n this e xample, “SETTING MENU (4)” appears on the TV screen and “DIGIT AL IN 1” appears on the displa y .
29 In this case, set the distance as f ollows: Left front speaker (FL): “FL SPK DIST .: 3.0m (10ft)” Right front speaker (FR): “FR SPK DIST .: 3.0m (10ft)” Center speaker (C): “C SPK DIST .: 3.0m (10ft)” Left surround speaker (SL): “SL SPK DIST .
30 Selecting the main or sub channel —DUAL MONO Y ou can select the playbac k sound (channel) you want while playing digital softw are recorded (or broadcasted) in Dual Mono mode (see page 42), which includes two monaural channels separately . When the receiver detects Dual mono signals , the DU AL MONO indicator lights up on the displa y .
31 Setting the digital input (DIGIT AL IN) terminals—DIGIT AL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals—DIGIT AL IN 1/2/3 (see page 16) so that the correct source name will appear when y ou select the digital source.
32 Selecting the output video signals —VIDEO OUTPUT To use the video conv ersion function (see page 9), you need to select this setting according to the connection method f or a TV . VIDEO OUTPUT : HDMI Select this when connecting a TV with the HDMI cable.
33 Sound adjustments Y ou can make sound adjustment to y our pref erence after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses for details. •Y ou cannot select the items which is not av ailable with the current setting.
34 DIGITAL EQ 250Hz ADJUST MENU (1) 5 SUBWOOFER LEVEL : 0 FRONT L LEVEL : 0 FRONT R LEVEL : 0 CENTER LEVEL : 0 SURR L LEVEL : 0 SURR R LEVEL : 0 S BACK L LEVEL : 0 S BACK R LEVEL : 0 ∞ :ENTER :EXIT .
35 Menu operating procedure When operating, the on-screen displa y appears on the TV screen regardless of the SUPERIMPOSE setting (see page 32). Before y ou star t, remember... There is a time limit in doing the f ollowing steps . If the setting is canceled bef ore you finish, start from step 1 again.
36 From the remote control: 1 Press TEST to check the speaker s’ output balance . • On the TV screen, “TEST T ONE” appears. The indicator corresponding to the speaker appears while a test tone comes out of the speakers . EX.: • On the displa y , “TEST L ” star ts flashing, and a test tone comes out of the speakers cloc kwise.
37 7 Attenuating the input signal—INPUT A TT When the input lev el of analog source is too high, the sound will be distor ted. If this happens, you need to atten uate the input signal lev el to prev ent the sound distor tion. • Once you hav e made an adjustment, it is memorized for each source.
38 7 Adjusting the sound localization of the center channel—CENTER GAIN This setting is av ailable only when Neo:6 Music is in use. • If “CENTER SPK” is set to “NO” (see page 28), this item is not adjustable. • Once you hav e made an adjustment, it is memorized until you change the setting.
39 T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in.
40 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10.
41 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speak ers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed.
42 DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software b y using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver pro vides the follo wing DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
43 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls.
44 Using the Surround/DSP modes Av ailable Surround/DSP modes v ary depending on the speaker settings and the incoming signals. See the tab le below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels.
45 On the front panel: Before y ou star t, remember... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again.
46 110V 127V 220V 230 - 240V AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD player*, and VCR) through this receiver .
47 One-touch DVD play Simply by starting playbac k on the D VD player , you can enjo y the D VD playback without setting other s witches manually . The follo wing is set automatically: •T ur ning on the receiver . • Changing the source to “D VR/D VD .
48 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals—remote codes “A” and “B.
49 Y ou can alwa ys perform the following operation: D VR/D VD : Tu rn on or off the D VD recorder or D VD play er. After pressing D VR/D VD , you can perf or m the f ollowing operations on the D VD recorder and D VD player . 3 : Star t playbac k. 7 : Stop pla yback.
50 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Refer also to the man uals supplied with the other products.
51 ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manuf acturers’ codes f or VCR” on the right. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR.
52 Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S.
53 Tr oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solve, contact y our JVC’ s service center. PROBLEM The power does not come on. The receiver turns off (enters standby mode). “O VER HEA T” flashes on the displa y , then the receiver turns off.
54 PROBLEM Remote control does not operate as y ou intend. Remote control does not work. Continuous hiss or buzzing during FM reception. Occasional crac king noise during FM reception. POSSIBLE CA USE The remote control is not ready f or your intended operation.
55 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 130 W* per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 0.8% total harmonic distor tion (IEC268-3/DIN).
DIGITAL IN 2(DBS) 1(DVR/ DVD) LEFT RIGHT LEFT RIGHT LEFT RIGHT ANTENNA COAXIAL AM LOOP FM 75 AM EXT SUBWOOFER OUT 3(VCR) DIGITAL OUT PCM/STREAM ANTENNA USB WIRELESS CAUTION:SPEAKER IMPEDANCE 6 - 16 LE.
Ein wichtiger Punkt beim Kauf des Geräts JVC RX-D701S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC RX-D701S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC RX-D701S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC RX-D701S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC RX-D701S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC RX-D701S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC RX-D701S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC RX-D701S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC RX-D701S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
