Benutzeranleitung / Produktwartung GVT0142-001A des Produzenten JVC
Zur Seite of 88
COMP A CT COMPONENT SYSTEM FS-Y1 Consists of CA-FSY1 and SP-FSY1 GVT0142-001 A [J] INSTR UCTIONS For Custo mer Use: Enter below the Model No . and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information f or future reference .
G-1 IMPORTANT FOR LASER PRODUCTS CAUTION T o reduce the risk of electr ical shocks, fire , etc.: 1. Do not remove scre ws, cov ers or cabinet. 2. Do not expose this appliance to rain or moisture. CAUTION — STANDBY/ON button! Disconnect the mains plug to shut the power off completely (the ST ANDBY lamp goes off).
1 Introduction Introduction About discs ...................................................... 3 Description of parts ......................................... 5 Getting started Using the remote control ................................. 6 Putting the batteries in the remote control .
2 7 Important cautions Installation of the system • Select a place which is lev el, dry and neither too hot nor too cold; between 5°C and 35°C (between 41°F and 95°F). • Leav e sufficient distance between the system and the TV . • Do not use the system in a place subject to vibration.
3 Introduction About discs This system has been designed to play back the f ollowing discs: DV D V I D E O, DV D AU D I O , V C D, S V C D, C D This system can also play bac k the f ollowing discs: • Finalized D VD-R/-RW discs recorded in the D VD VIDEO f ormat.
4 Notes on all files • The system can only recognize and pla y files with one of the follo wing e xtensions, which can be in any combination of upper and lower case; • MP3: “.MP3”, “.mp3” • WMA: “.WMA” , “.wma” • JPEG: “.JPG”, “.
5 Introduction The numbers represent the page numbers. * Connect headphones (not suppl ied) with a stereo mini plug. If the headphones are connected, th e speakers and subwoof er will not produce any sound.
6 The numbers represent the page numbers. If the range or effectiv eness of the remote control decreases, replace the batteries. Use two R6 (SUM-3)/AA(15F) type dr y-cell batter ies. CAUTION • Do not use a use d battery and a ne w battery together .
7 Introduction This page is for when operating y our TV using the remote control o f this product. Setting the manufacturer's code 1 Slide the remote control mode selector to the TV side. 2 Keep pressing down TV. NOTE Keep pressing down TV until Step 4 is com plete.
8 Connection When positioning the antenna, listen to an actual radio prog ram (ref er to “Listening to a radio broadcast” on page 32). Connecting antennas C onnecting AM loop antenna ( supplied ) 1 Set up the AM loop antenna. 2 Connect antenna cords.
9 Connecting up Connection There is no d iff erence between the left and r ight speakers. CAUTION • DO NOT conn ect more than one speaker to one speaker terminal. • The speakers of this product are magneticall y shielded, but color irregulari ties may occur on the TV depending on how the speake rs are installed.
10 Connecting up Connection This page is for when connecting the main unit with other de vices. Connecting subwoofer Connecting with other audio device When you want to hear sound from the subwoof er , press S.WFR OUT on the remote co ntrol to display “SUBWOOFER” on the displa y window on the main unit.
11 Connecting up Connection CAUTION Connect the mai n unit di rectl y with a TV (or a monitor) withou t routing through a VCR. Otherwis e it may cause picture distor tion while pla ying. Also, when c onnecting the main unit to a T V with a VCR built in, there may be picture distortion while playing .
12 (Refer to page 17 for pla yin g MP3/WMA and JPEG.) • The power will be turned on when any of PLA Y 3 , FM, AM, A UX, or 0 on the main unit and D VD/CD 3 , FM, AM, A UX, or 0 OPEN/CLOSE on the remote control i s pressed while th e power is off .
13 Basic operations Display window during disc playback Ex.: When a D VD VIDEO is play ed Ex.: When a D VD A UDIO is pl ay ed If “BONUS” or “B.S .P . ” is display ed during a D VD A UDIO pl a yback, ref er to page 27. Ex.: When an SVCD or VCD is playe d • When playing an SVCD , the SVCD indi cator lights instead of th e VCD indicator.
14 Playing discs (continued) NOTE • Set the remote control mode selector to AUDIO before using the number buttons. • For a VCD or SVCD, this operation can be carried out when the disc is stopp ed, or during playback without the PBC functi on.
15 Basic operations Press during playback. NOTE • This operation may not be carried out for some discs. • It is not possible to go back to the previous title. Press SLOW or SLOW during pause. • Each time you press the b utton, the pla yback speed increases ( × 1/32, × 1/16, × 1/8, × 1/4, × 1/ 2).
16 Playing discs (continued) Press DIMMER repeatedly. • Each time you press the b utton, the dimmer mode changes as follows: • When the unit is tur ned off, pressing DISPLA Y tur ns off the clock indication to sav e th e power consumption. The items abov e can be carr ied out for all sources.
17 Advanced operations Display of an MP3/WMA disc is described here as an e xample. F or a JPEG disc, read “trac k” as “file”. NOTE When playing a disc contai ning both MP3/WMA and JPEG files, set one of them to be playe d (page 29). 1 Load a disc.
18 NOTE Set the remote control mode select or to AUDIO before using the number butt ons. This system can store the stop point, and when you start playback again b y pressing D VD/CD 3 (e ven while on standb y), it star ts from the position where you hav e sto pped—Resume Play .
19 Advanced operations NOTE Set the rem ote control mode selector to AUDIO before using the nu mber buttons. 1 Press MENU or TOP MENU while the disc is stopped or during playback *1 . • The disc menu screen will be display ed. •O n l y TO P M E N U can be used f or D VD A UDIOs.
20 NOTE Set the remote control mode select or to AUDIO before using the number butt ons. It is possible to program a maximum of 99 chapters or trac ks. The same chapter or trac k can be programmed more than once. 1 While the disc is stopped, press PLAY MODE repeatedly to display “PRGM.
21 Advanced operations To program on the display window on th e main unit, operate as follows: (1) Select a title/grou p using the number buttons . (2) Designate a chapter/track number using the number b uttons. • Ref er to “How to use the n umber buttons” (page 15).
22 Refer to page 17 for Repeat Playbac k of MP3 and JPEG files. 1 Press REPEAT during playback. • Each time you press the button, the Repeat mode and its indication chang e as f ollows: F or D VD VI.
23 Advanced operations 1 Press ON SCREEN twice during playback. The menu bar (page 28) will be displa yed. 2 Press cursor 2 / 3 to select . 3 Press ENTER.
24 1 Press SUBTITLE during playback of a di sc containing subtitles in several languages. • Each time you press th e b utton, the subtitle will be alter nated between ON and OFF . 2 Press cursor 5 / ∞ to select a subtitle language. • F or a language code such as “AA”, refer to “Language codes” (page 38).
25 Advanced operations 1 Press ZOOM du ring playback or while paused. • Each time you press the button, the picture magnification will be chan ged. • (F or a JPEG) Y ou cannot chan ge the picture magnification dur ing slide-show playbac k. 2 Select the portion you want to see by using cursor 3 / 5 / 2 / ∞ .
26 Other convenient functions (continued) The two speak ers produce an effect resembling surround-sound. 1 Press 3D PH ONIC during playback. • Each time y ou press the b utton, the 3D PHONIC will be alternated as fol lows: • While 3D PHONIC is activ ated, “ 3D PHONIC ” appears and the 3D PHONIC indicator lights on the display window .
27 Advanced operations NOTE Set the remote control mode select or to AUDIO before using the number buttons. There are some D V D A UDIO di scs with a speci al group , called “Bonus Group”, recorded. NOTE This operation can be carrie d out when “BONUS” is lit on the display window on the main uni t.
28 NOTE • Set the remote control mode selector to AUDIO before using the number buttons. • This operation can be carried out when there is a disc loaded. There are some functions that may no t work while the di sc is stopped. 1 Press ON SCREEN twice.
29 Advanced operations NOTE The playback status mark has the same meaning of the mark on t he On-screen guid e ( page 15). The initial settings of the system can be changed according to the environment the system is used in. NOTE • S et the rem ote cont rol mode s elector to AUDIO before using the number buttons.
30 Preferences (continued) AUDIO Items Contents ( : initial setting) DIGIT AL A UDIO OUTPUT Select an output signal type fr om the fol lowing in accordance with the de vice connected to the digital aud io output terminal (A V amplifier , etc.). (See the list below f or the pref erence items and ou tput signal.
31 Advanced operations AD Andorra AE United Arab Emirates AF Afghanistan AG Antigua and Barbuda AI Anguilla AL Albania AM Armenia AN Netherlands Antilles AO Angola AQ Antarctica AR Argentina AS Americ.
32 NOTE • Set the remote control mode selector to AUDIO before using the number buttons. Y ou can tu ne in to FM or AM. 1 Press FM or AM. 2 Press ¢ / 4 to select the station (frequency). A utomatic tuning: Hold down ¢ / 4 until the system starts searching, and then re lease the button.
33 Presetting stations in the system allows y ou to easily tune in to a station. NOTE Set the remote control mode select or to AUDIO before using the number buttons. The system stores up to 30 FM stations and up to 15 AM stations. 1 Select a statio n you want to store (page 32 for how to select).
34 Connect the other audio device to this system in adv ance (pa ge 10). 1 Press AUX. The source changes to A UX. 2 Play the other audio device. F or details, refer to the manual of the de vi ce connected. 3 Adjust the vol ume and the sound quality of the system (page 10).
35 How the daily timer w orks Once the daily timer has been set, the timer indicato r and time r number indicator (1/2/3) are lit on the display window . Daily ti mer tur ns on the system at the same time e v eryday until the timer setting is canceled manually or another dail y timer is activated.
36 When the time you specif y elapses, the system will be tur ned off by itself . Press SLEEP. Each time you press the button, the time indicated on the display window on the main unit changes (in minutes). Changing the time Reselect the time by pressing SLEEP repeatedly .
37 Reference When you encounter a problem that seems to be a fault, check the f ollowing points be f ore contacting your JVC service center : Power source 7 Power does not come on. • The power cord is not connected to the main unit or an A C outlet.
38 Reference Others 7 It is not possible to switch audio or subtit les between langu ages. • The disc does not contain 2 or more languages. → If only a single lang uage is recorded on the disc, switching to another languag e is impossible (page 24).
39 General P ower source: AC 120 V , 60 Hz P ower consumption: 25 W (in operati on) 1.0 W (on standb y) Wei ght: 2.7 kg (6.0 lbs) External dimensions 150 mm x 152 mm x 246 mm ( WxHxD ) : ( 5 15 / 16 in.
FS-Y1[J].book Page 40 Monday, J anuary 31, 2005 12:04 PM.
BT -51005-9 (0904) FS-Y1[J].book Page 41 Monday, J anuary 31, 2005 12:04 PM.
2005 Victor Company of Japan, Limited EN 0 2 05AIMMWJEM FS-Y1 COMPACT T COMPONENT SYSTEM c FS-Y1[J].book Page 42 Monday, J anuary 31, 2005 12:04 PM.
FS-Y1 — Consists of CA-FSY1 and SP-FSY1 — Composé CA-FSY1 et SP-FSY1 INSTR UCTIONS Français English GVT0142-002 A [C] MANUEL D’INSTRUCTIONS COMP A CT COMPONENT SYSTEM SYSTEME DE COMPOSANTS COMPACT FS-Y1[C].
G-1 IMPORTANT FOR LASER PRODUCTS CAUTION T o reduce the risk of electr ical shocks, fire , etc.: 1. Do not remove scre ws, cov e rs or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d’éviter tout risque d’électrocution, d’incendie, etc.
G-2 FS-Y1[C].book Page 2 Wednesd ay, February 16, 2005 7:46 AM.
G-3 For Canada/ pour le Ca nada CA UTION: T O PREVENT ELECTRIC SHOCK, MA TCH WIDE BLADE OF PLUG T O WIDE SLO T , FULL Y INSERT . A TTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTR ODUIRE LA LAME LA PLUS LARGE DE LA FICHE D ANS LA BORNE CORRESPOND ANTE DE LA PRISE ET POUSSER JUSQU AU FOND .
1 Introduction English Introduction About discs ...................................................... 3 Description of parts ......................................... 5 Getting started Using the remote control ................................. 6 Putting the batteries in the remote control .
2 English 7 Important cautions Installation of the system • Select a place which is lev el, dry and neither too hot nor too cold; between 5°C and 35°C. • Leav e sufficient distance between the system and the TV . • Do not use the system in a place subject to vibration.
3 Introduction English About discs This system has been designed to play back the f ollowing discs: DV D V I D E O, DV D AU D I O , V C D, S V C D, C D This system can also play bac k the f ollowing discs: • Finalized D VD-R/-RW discs recorded in the D VD VIDEO f ormat.
4 English Notes on all files • The system can only recognize and pla y files with one of the follo wing e xtensions, which can be in any combination of upper and lower case; • MP3: “.MP3”, “.mp3” • WMA: “.WMA” , “.wma” • JPEG: “.
5 Introduction English The numbers represent the page numbers. * Connect headphones (not suppl ied) with a stereo mini plug. If the headphones are connected, the speakers and subwoof er will not produce any sound.
6 English The numbers represent the page numbers. If the range or effectiv eness of the remote control decreases, replace the batteries. Use two R6 (SUM-3)/AA(15F) type dr y-cell batter ies. CAUTION • Do not use a use d battery and a ne w battery together .
7 Introduction English This page is for when operating y our TV using the remote control o f this product. Setting the manufacturer's code 1 Slide the remote control mode selector to the TV side. 2 Keep pressing down TV. NOTE Keep pressing down TV unti l Step 4 is complete.
8 Connection English When positioning the antenna, listen to an actual radio prog ram (ref er to “Listening to a radio broadcast” on page 32). Connecting antennas C onnecting AM loop antenna ( supplied ) 1 Set up the AM loop antenna. 2 Connect antenna cords.
9 Connecting up Connection English There is no d iff erence between the left and r ight speakers. CAUTION • DO NOT conn ect more than one speaker to one speaker terminal. • The speakers of this product are magneticall y shielded, but color irregulari ties may occur on the TV depending on how the speake rs are installed.
10 Connecting up Connection English This page is for when connecting the main unit with other de vices. Connecting subwoofer Connecting with other audio device When you want to hear sound from the subwoof er , press S.WFR OUT on the remote co ntrol to display “SUBWOOFER” on the displa y window on the main unit.
11 Connecting up Connection English CAUTION Connect the mai n unit di rectl y with a TV (or a monitor) withou t routing through a VCR. Otherwis e it may cause picture distor tion while pla ying. Also, when c onnecting the main unit to a T V with a VCR built in, there may be picture distortion while playing .
12 English (Refer to page 17 for pla yin g MP3/WMA and JPEG.) • The power will be turned on when any of PLA Y 3 , FM, AM, A UX, or 0 on the main unit and D VD/CD 3 , FM, AM, A UX, or 0 OPEN/ CLOSE on the remote control is pressed while the power is off .
13 Basic operations English Display window during disc playback Ex.: When a D VD VIDEO is play ed Ex.: When a D VD A UDIO is pl ay ed If “BONUS” or “B.
14 Playing discs (continued) English NOTE • Set the remote control mode selector to AUDIO before using the number buttons. • For a VCD or SVCD, this operation can be carried out when the disc is stopp ed, or during playback without the PBC functi on.
15 Basic operations English Press during playback. NOTE • This operation may not be carried out for some discs. • It is not possible to go back to the previous title. Press SLOW or SLOW during pause. • Each time you press the b utton, the pla yback speed increases ( × 1/32, × 1/16, × 1/8, × 1/4, × 1/2).
16 English Playing discs (continued) Press DIMMER repeatedly. • Each time you press the b utton, the dimmer mode changes as follows: • When the unit is tur ned off, pressing DISPLA Y tur ns off the clock indication to sav e th e power consumption.
17 Advanced operations English Display of an MP3/WMA disc is described here as an e xample. F or a JPEG disc, read “trac k” as “file”. NOTE When playing a disc contai ning both MP3/WMA and JPEG files, set one of them to be playe d (page 29). 1 Load a disc.
18 English NOTE Set the remote control mode select or to AUDIO before using the number butt ons. This system can store the stop point, and when you start playback again b y pressing D VD/CD 3 (e ven while on standb y), it star ts from the position where you hav e sto pped—Resume Play .
19 Advanced operations English NOTE Set the remote control mode selector to AUDIO before using the number buttons. 1 Press MENU or TOP MENU while the disc is stopped or during playback *1 . • The disc menu screen will be display ed. •O n l y TO P M E N U can be used for D VD AU D I O s .
20 English NOTE Set the remote control mode select or to AUDIO before using the number butt ons. It is possible to program a maximum of 99 chapters or trac ks. The same chapter or trac k can be programmed more than once. 1 While the disc is stopped, press PLAY MODE repeatedly to display “PRGM.
21 Advanced operations English To program on the display window on the ma in unit, operate as follows: (1) Select a title/grou p using the number buttons . (2) Designate a chapter/track number using the number b uttons. • Ref er to “How to use the number b uttons” (page 15).
22 English Refer to page 17 for Repeat Playbac k of MP3 and JPEG files. 1 Press REPEAT during playback. • Each time you press the button, the Repeat mode and its indication chang e as f ollows: F or.
23 Advanced operations English 1 Press ON SCREEN twice during playback. The menu bar (page 28) will be displa yed. 2 Press cursor 2 / 3 to select . 3 Press ENTER.
24 English 1 Press SUBTITLE during playback of a di sc containing subtitles in several languages. • Each time you press th e b utton, the subtitle will be alter nated between ON and OFF . 2 Press cursor 5 / ∞ to select a subtitle language. • F or a language code such as “AA”, refer to “Language codes” (page 38).
25 Advanced operations English 1 Press ZOOM du ring playback or while paused. • Each time you press the button, the picture magnification will be chan ged. • (F or a JPEG) Y ou cannot chan ge the picture magnification dur ing slide-show playbac k.
26 Other convenient functions (continued) English The two speak ers produce an effect resembling surround-sound. 1 Press 3D PH ONIC during playback. • Each time y ou press the b utton, the 3D PHONIC.
27 Advanced operations English NOTE Set the remote control mode select or to AUDIO before using the number buttons. There are some D V D A UDIO di scs with a speci al group , called “Bonus Group”, recorded. NOTE This operation can be carrie d out when “BONUS” is lit on the display window on the main uni t.
28 English NOTE • Set the remote control mode selector to AUDIO before using the number buttons. • This operation can be carried out when there is a disc loaded. There are some functions that may no t work while the di sc is stopped. 1 Press ON SCREEN twice.
29 Advanced operations English NOTE The playback status mark has the same meaning of the mark on t he On-screen guid e ( page 15). The initial settings of the system can be changed according to the environment the system is used in. NOTE • S et the rem ote cont rol mode s elector to AUDIO before using the number buttons.
30 Preferences (continued) English AUDIO Items Contents ( : initial setting) DIGIT AL A UDIO OUTPUT Select an output signal type fr om the fol lowing in accordance with the de vice connected to the digital aud io output terminal (A V amplifier , etc.).
31 Advanced operations English AD Andorra AE United Arab Emirates AF Afghanistan AG Antigua and Barbuda AI Anguilla AL Albania AM Armenia AN Netherlands Antilles AO Angola AQ Antarctica AR Argentina A.
32 English NOTE • Set the remote control mode selector to AUDIO before using the number buttons. Y ou can tu ne in to FM or AM. 1 Press FM or AM. 2 Press ¢ / 4 to select the station (frequency). A utomatic tuning: Hold down ¢ / 4 until the system starts searching, and then re lease the button.
33 English Presetting stations in the system allows y ou to easily tune in to a station. NOTE Set the remote control mode select or to AUDIO before using the number buttons. The system stores up to 30 FM stations and up to 15 AM stations. 1 Select a statio n you want to store (page 32 for how to select).
34 English Connect the other audio device to this system in adv ance (pa ge 10). 1 Press AUX. The source changes to A UX. 2 Play the other audio device. F or details, refer to the manual of the de vi ce connected. 3 Adjust the vol ume and the sound quality of the system (page 10).
35 English How the daily timer w orks Once the daily timer has been set, the timer indicato r and time r number indicator (1/2/3) are lit on the display window . Daily ti mer tur ns on the system at the same time e v eryday until the timer setting is canceled manually or another dail y timer is activated.
36 English When the time you specif y elapses, the system will be tur ned off by itself . Press SLEEP. Each time you press the button, the time indicated on the display window on the main unit changes (in minutes). Changing the time Reselect the time by pressing SLEEP repeatedly .
37 Reference English When you encounter a problem that seems to be a fault, check the f ollowing points be f ore contacting your JVC service center : Power source 7 Power does not come on. • The power cord is not connected to the main unit or an A C outlet.
38 Reference English Others 7 It is not possible to switch audio or subtit les between langu ages. • The disc does not contain 2 or more languages. → If only a single lang uage is recorded on the disc, switching to another languag e is impossible (page 24).
39 English General P ower source: AC 120 V , 60 Hz P ower consumption: 25 W (in operati on) 1.0 W (on standb y) Wei ght: 2.7 kg External dimensions (W x H x D): 150 mm x 152 mm x 246 mm DVD player Pla.
2005 Victor Company of Japan, Limited EN, FR 0205AIMMDWJEM FS-Y1 COMPACT T COMPONENT SYSTEM c FS-Y1[C].book Page 40 Wednesd ay, February 16, 2005 7 :46 AM.
Ein wichtiger Punkt beim Kauf des Geräts JVC GVT0142-001A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC GVT0142-001A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC GVT0142-001A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC GVT0142-001A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC GVT0142-001A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC GVT0142-001A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC GVT0142-001A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC GVT0142-001A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC GVT0142-001A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
