Benutzeranleitung / Produktwartung GoToNova 8401 des Produzenten iOptron
Zur Seite of 43
SmartStar ® CubePro TM Instruction Manual.
2 T able of Content Table of Content .............................................................................................................. 2 1. Introduc tion ....................................................................................
3 5.5.13. Set Language ............................................................................................. 15 5.6. A lign .................................................................................................................... 15 5.
4 1. Introduction 1.1. CubePro Features CubePro TM GOTO altazimuth (A/A) Mount is the ideal portable mount to go with your traveling OTAs, such as a 60mm or 80mm ED refractor, a 90mm or 100mm Maksutov-Cassegrain or a 114mm Newtonian reflector. It can also be used to mount solar scopes.
5 1.2. CubePro TM Assembly Terms 1. Telescope (not included) 2. Dovetail Lock 3. Hand Controller 4. Altitude Lock 5. Mount 6. Tripod 7. Inner support/Tripod bolt 8.
6 2. CubePro Assembly Step 1. Extend tripod legs to full extension. Step 2. Attach mount to tripod using the long bolt (#7). Slide tray on bottom of shaft. Then screw on round blac k knob (#9). Step 3. Installing Batteries Pull the batteries compartment cove r (shown) open.
7 Step 6. Connecting Hand Controller Plug hand controller into any one of the HBX (han dbox) ports on the mount. Plug in power plug if a AC adaptor is used. Turn on power. Now you ar e ready to observe. Use the 4 Arrow keys ( ▲▼◄► ) to rotate the scope Up, Down, Left, and Right.
8 3. GOT ONOV A TM 8401 Hand Controller Figure 2. GOTONOVA 8401 Hand Controller GOTONOVA TM 8401 hand controller (HC) is the standard controller for a CubePro, as shown in Figure 2. 3.1. Key Description • MENU: Press “MENU” to enter the Main Menu.
Figure 3. 8401 HC LCD Information Screen 3.2. The LCD Screen The 8401 HC is designed to use for both iOptron’s equatorial (EQ) mount, such as the SmartStar ® -PR GOTO German Equatorial Mount and the GOTONOVA TM Equatorial Kit, and AltAzimuth (A/A) mount, which includes all SmartStar ® GOTO mounts and telescopes.
10 • Level the Mount. Adjust the leg length to make sure the bubble on the side of the mount is centered. Turn the Mount around to make sure it is always leveled. It is also recommended to use additional levels to assure very precise leveling. Leveling is critical for a good GOTO and tracking accuracy.
11 changed to N47º31'48”: 47.53º = 47º +0.53º, 0.53º=0.53x60'=31.8', 0.8'=0.8x60"=48". Therefore, 47.53º=47º31'48" or 47d31m48s.
12 Press Enter. Select Alt/Azi mount and press ENTER to go back the previous screen. 4.2.4. Set Anti-backlash For an Alt/Azi operation, both R.A. and DEC anti-backlash should be set to 0 step (factory default setting). Scroll down and select “Set anti-backlash” Press ENTER.
13 Select an object using ▲ or ▼ key. Then press ENTER. Next use the arrow keys to slew to the object until it is centered in your eyepiece. Then press ENTER. You may need using number keys to change the slewing speed to make the centering procedure easier.
14 5.2.4. Asteroids This catalog contains up to 4096 asteroids. This database is customer upgradeable. 5.2.5. Stars • Named Stars: consists of 191 stars with their common names. They are listed alphabetically. A list is attached in Appendix C. • Double Stars: consists of 40 double stars.
15 5.5.5. Set Eyepi ece Light If you have an illuminated-reticule eyepiece or illuminated polar scope, an d it is supported by GOTONOVA hand controller-- use this option to adjust the light intensity. 5.5.6. Set Backlight Adjust LCD and keypad backlight.
16 5.6.3. Three-Sta r Align It will increase the accuracy even higher and requires an even wider view of the sky. This basically asks you to choose a third star to align after two-star align. Three star alignment is not available for Alt/Azi mode. 5.6.
17 6. Maintenance and Servicing 6.1. Maintenance The CubePro is designed to be maintenance free. Do not overload the mount. Do not drop the mount which will damage the mount or affect the GOTO tracking accuracy permanently. Use a wet cloth to clean the mount and hand controller.
18 4. Star Alignment accuracy; GOTO accuracy 1. Leveling (very important). 2. Site information (minutes ahead or behind UT, DST). 3. System balancing. 4. Use most updated firmware. 5. Select right mount type (A/A). 6. Set backlash to 0 in both DEC and RA.
19 Appendix A. T echnical Specifications Mount AltAzimuth Mount Body Materials Die-cast Aluminum Motor Dual-Axis DC Servomotor, DC12V Speed Dual-Axis, 9-Gear, Electronic (1×,2×,8×,16×,64×,128×,256×,512×,MAX ） GPS 32-channel GPS GOTO System GOTONOVA TM 130,000+ objects database Tracking Automatic Payload 12 lb Counterweight 3.
20 Appendix B. GOT ONOV A TM 8401 HC MENU STRUCTURE MENU Select and Sl ew Select and Sl ew Plane ts, Sun, Mo on Plane ts, Sun, Mo on Comets Comets Asteroids Asteroids Stars Stars Mercury Venus Mars Ju.
21 Set Up Controller Set Up Controller Set Up Local Time Set Up Site Set N/S Hemisphere Set Displa y Contrast Set Eyepiece Light Set Backlight Set Anti-backs lash Set Key Beep Set Mount Type Reset All.
22 Appendix C. GOT ONOV A TM S t ar List GotoNova Deep Sky Object List for 8401 ID No. OBJECT NGC # Messier # IC# A(Abell) U(UGC) 1 Andromeda Galaxy 224 31 2 Barnards Galaxy 6822 3 Beehive Cluster 263.
23 35 Keyhole Ne bula 3372 36 Lagoon Nebula 6523 8 37 Little Gem 6445 38 Little Gem Nebula 6818 39 Little Ghost Nebula 6369 40 North Ameri can Nebula 7000 41 Omega Nebula 6618 17 42 Orion Nebula 1976 .
24 Modern Constellations No. Constellation Abbreviation No. Constellation Abbreviation 1 A ndromeda A nd 45 Lacerta Lac 2 A ntlia A nt 46 Leo Leo 3 A pus A ps 47 Leo Minor LMi 4 A quarius A qr 48 Lepu.
25 GOTONOVA Named Star List for 8401 001 Acamar 049 Ascella 097 Kaus Australis 145 Rassalas 002 Achernar 050 Ase llus Australis 098 Kaus Borealis 146 Rasa gethi 003 Acrux 051 Asellus Borealis 099 Kaus.
26 GOTONOVA Double Star List for 8401 No. Object Const SAO Name 1 Eta Cas 21732 Achird 2 Alpha Psc 110291 Alrisha 3 Theta Per 38288 4 Alpha For 168373 Fornacis 5 Alpha Aur 40186 Capella 6 Sigma Ori 13.
27 Appendix D. Set Up USB-PC Connection 1. Download USB2COM driver (cp2102.zip file for 8401) from iOptron Website 2. Install cp2101(usb2com) driver Choose the appropriate driver for your OS. In this case is a Windows XP operation system. Double click on it, and you will see: Click “Next”.
28 Select “I accept the terms of license agreement”, and click “Next” Using the default installation path, c:SiLabsMCUCP210x, or specify your own path by click “Change”.
29 When finished installation, click “Finish” 3. Plug the USB cable to the USB port on your PC, plug the other end of the USB cable to hand controller. Turn on the power on the mount. 4. Install the Hardware The computer will find a new hardware and show the following screen Select “No, not this time” and click “Next”.
30 Select “Install from a list or specific location” and click “Next”. Select “Search for the best driver in these locations,” and che ck “Include this location in the search.” Click on “Browse” and select the cp210x driver from directory c:SiLabsMCUCP210xWin2K_XP, click OK.
31 Click “Next”. The computer will start to install the driver for the USB2COM. When the installa tion is done, click “Finish”. If the computer shows “find a new hardware” screen again, just repeat the steps in this section again.
32 Now you computer should be ready for Firmware Upgrading, computer communication with the mount via ASCOM platform and planetarium software applications.
33 Double click on “Ports(COM & LPT)”, find out the COM number and write it down (in the following figure, it is COM4).
34 Appendix E. Firmware Upgrade 1. Download and install Firmware Downloader from iOptron Website 2. Double click and open “iOptron Downloader” On the interface, select appropriate port using pull-.
35 Click “Open Data File”, and select appropriate “.bin” file that matches your hand cont roller. and click “Open”. Select “Main Program” in Update Type.
36 Now the upgrade is finished. Typical Errors: 1. Invalid Port Number: in Device Manager, make sure you have the correct COM port number for CP210x. 2. Wrong “.bin” file: make sure you have the correct “.bin” file for firmware upgrade. 3. Wrong downloader, you should use iOptron Downloader instead of the Flash Downloader.
37 Appendix F . Use a PC to Control an iOptron Mount In general you need the followings to use a PC to control the mount, 1. Download USB2COM driver (cp2102, zip file for 8401 and 8402A) http://www.ioptron.com/manuals/USB_2COM_Driver.zip; 2. Install USB2COM and establish the connection between the mount and the PC (see instruction); 3.
38 Appendix G . RS-232 Command Set Abbreviations used: DD or DDD degrees or day of t he month depending on the context HH hours MM minutes or month depending on the context MM.M minutes and tenths of minutes s + or – sign, assumed to be + if omitted SS seconds SS.
39 Get the current latitude. Command: :GL# Response: HH:MM:SS.S# Get the current local time in 24 hour format. Overflows from 23:59:59 to 00:00:00. Command: :GS# Response: HH:MM:SS.S# Get the current local sidereal time in 24 hr. format. Command: :GR# Response: HH:MM:SS.
40 Stop motion in the specified axis. Note that :Qn# is identical to :Qs#, and :Qe# is identical to :Qw#. Motion is terminated only if it was not started by a slew (:MS#) command. Command: :Q# Response: (none) Motion in both axes is stopped, regardl ess of how the motion was invoked.
41 Command: :Sr HH:MM:SS.S# Response: “1” Define the commanded Right Ascension, RA. Command: :Sd sDD*MM:SS# Response: “1” Define the commanded Declination. Miscellaneous Command: :F+# :F-# :FF# :FS# :FQ# Response: (none) Advances (F+) or retracts (F-) focus adjus t motor on the eyepiece.
42 Response: (none) This command sets the guide rate. 0 – 1.0X of sidereal 1 – 0.8X of sidereal 2 – 0.6X of sidereal 3 – 0.4X of sidereal Command: :GGS# Response: ‘0’,’1’,2,’3’ This command gets the current guide rate. 0 – 1.0X of sidereal 1 – 0.
43 IOPTRON TWO YEAR TELESCOPE, MOUNT, AND CONTROLLER WARRANTY A. iOptron warrants your telescope, mount, or cont roller to be free from defects in materials and workmanship for two years. iO ptron will repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workman ship.
Ein wichtiger Punkt beim Kauf des Geräts iOptron GoToNova 8401 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie iOptron GoToNova 8401 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für iOptron GoToNova 8401 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von iOptron GoToNova 8401 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über iOptron GoToNova 8401 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon iOptron GoToNova 8401 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von iOptron GoToNova 8401 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit iOptron GoToNova 8401. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei iOptron GoToNova 8401 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
