Benutzeranleitung / Produktwartung I945P des Produzenten Intel
Zur Seite of 70
TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice.
ii DISCLAIMER OF W ARRANTIES: THERE ARE NO W ARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE F ACE OF THE MANUFACTURER LIMITED W ARRANTY . THE MANUF ACTURER EXPRESSL Y EXCLUDES ALL OTHER W ARRANT.
iii P ost P or t F r equently Asked Questions Below is a list of some basic POST Codes, possible problems and solutions. For more detailed information about POST Codes, refer to Appendix in this manual. P O S T CO DE P ro b l em S o lut i on FFh o r CFh 1 .
iv T able of Contents Section 1 Introduction Package Contents ...................................................... 1- 1 Mainboard Features ................................................... 1- 2 System Block Diagram ................................
v Power BIOS Features ................................................ 4-19 Defaults Menu ........................................................... 4-22 Supervisor/User Password Setting ... ......................... 4- 2 3 Exit Selecting ...........
vi Page Left Blank.
Introduction Page 1-1 Section 1 INTRODUCTION 1-1 Package Contents Contents A. Mainboard B. User ’ s manual C. Floppy drive cable D. HDD drive cable E . CD (drivers and utilities) F . I/O Shield G. S-A T A II data and power cable Optional Items H. Extra USB2.
Introduction Page 1-2 1-2 Mainboard Fea tur es Brief Introduction Intel ® Pentium ® 4 processors The Pentium 4 processor is designed to deliver performance across applications and usages where end-users can truly appreciate and experience the performance.
Introduction Page 1-3 Ultra A T A100 The mainboard provides an Ultra A T A100 Bus Master IDE controller . This controller supports Ultra A T A100 protocols which are ideal to support demand- ing applications such as real-time video, multimedia, and a high performance operating system.
Introduction Page 1-4 Special Features & Magic Health Reports your system hardware status for every boot-up to help detect faults early. Monitor hardware status including CPU temperature, CPU/Memory/ Chipset voltage, fan RPM speed for chassis fan, CPU fan & Power supply fan.
Introduction Page 1-5 1-3 System Block Diagram.
Introduction Page 1-6.
Specification Page 2-1 Section 2 SPECIFICA TION Mainboard Specification Processor Socket LGA775 for Intel ® Celeron D ® 3xx series, Intel ® Pentium 4 ® 5xx/ 6xx series, P4EE up to 3.
Specification Page 2-2 IDE One IDE interface (up to 2 IDE devices) with UDMA-33, A T A-66/100 support from embedded IDE controller USB Eight USB connectors compliant with USB2.
Specification Page 2-3 BIOS Flash EEPROM with A ward Plug&Play BIOS Support ACPI S3 (Suspend T o RAM) mode in ACPI compliant O/S Support EZ Boot for fast bootable device selection .
Specification Page 2-4 Special Features Support KBPO function – Keyboard power on, turn on the computer from keyboard Support W ake-On-LAN by PME Support USB resume in S3 Onboard Pos.
Installation Page 3-1 Mainboard Layout Section 3 INST ALLA TION Note: Depending on the model you purchased, some components are optional and may not be available.
Installation Page 3-2 Easy Installation Procedure The following must be completed before powering on your new system: 3-1. CPU Installation 3-2. Jumper Settings 3-3. System Memory 3-4. VGA card installation 3-5. Device Connectors 3-1 CPU Installation Step 1 Open load plate ( A ) , DO NOT touch socket contacts ( B ).
Installation Page 3-3 Step 3 Remove the processor from the protective cover. Do not touch the bottom of the processor. The processor cover should not be discarded. Always replace the processor cover if the processor is removed from the socket. Step 4 Hold the processor with thumb and index fingers as shown.
Installation Page 3-4 3-2 Jumper Settings 1 Settings: 1-2: Normal (Default) 2-3: Clear CMOS JCMOS: Clear CMOS data Jumper If the CMOS data becomes corrupted or you forgot the supervisor or user password, clear the CMOS data to reconfigure the system back to the default values stored in the ROM BIOS.
Installation Page 3-5 JPCIE1~JPCIE2: PCI-E slot Control Jumper These jumpers redirect the PCI-E signals from PCI-EXP2 and PCI-EXP3 to the PCI-EXP4 connector. This allows 4x bandwidth on PCI-EXP4 slot to cater for higher bandwidth cards such as VGA and RAID connectors.
Installation Page 3-6 3-3 System Memor y Configuration The mainboard accommodates four 240-pin DDR2 DIMM sockets. • Supports up to 4GB of 400/533/667MHz DDR2 SDRAM (2GB and 400/ 533MHz for i945PL chipset support only). • Supports dual channel memory interface.
Installation Page 3-7 Memory configurations supported: M M I D 1 ) t i b - 4 6 ( M M I D 2 ) t i b - 8 2 1 ( M M I D 3 ) t i b - 8 2 1 ( M M I D 4 ) t i b - 8 2 1 ( 1 # M M I DS D / S SS D / S SS D / .
Installation Page 3-8 3-4 VGA Card Installation When installing the VGA card, make sure the card edge connector is fully inserted into the slot and the clicker is locked properly. <Figure 10> T o install a single VGA card in Single Mode, insert the VGA into the "PCI-EXP1" VGA slot.
Installation Page 3-9 “PCI-EXP4” VGA slot operates at PCI-E x4 bandwidth, the following table of VGA cards have been tested compatible with this slot.
Installation Page 3-10 3-5 Device Connectors The I/O back panel for this mainboard is shown below. When installing the mainboard into the computer case, use the bundled I/O shield to protect this back panel. <Figur e 13> - I/O Ports USB2.0 x 4 ports Parallel Port PS/2 Mouse PS/2 Keyboard RJ45 LAN COM S/PDIF-out Coaxial Jack 7.
Installation Page 3-11 FDD : Floppy Controller Connector This connects to the floppy disk drive. IDE1: A T A-66/100 IDE Connector This mainboard is equipped with 1 IDE connectors to support up to 2 A T A-100 IDE drives. It supports PIO and DMA mode operations for maximum data transfer rate of 100MB/sec per channel.
Installation Page 3-12 CD-IN: CD Audio_IN Connector The CD-IN connector is used to receive audio from a CD-ROM drive, TV tuner or MPEG card. CD_IN_Le ft 1 CD_IN_Ri ght CD_Referenc e CFP A : Front Panel Audio Connector This audio connector connects to the audio jacks located on the front panel.
Installation Page 3-13 CUSB3 CUSB4 CUSB3/CUSB4: Four USB 2.0 ports This mainboard includes additional USB2.0 ports, identified by 10-pin connector. If you wish to use the additional USB ports, install the card-edge bracket to the system chassis then insert its cables to this 10-pin connector.
Installation Page 3-14 CFP: Front Panel Connector HD_LED This LED will light up whenever the hard drive is being accessed. PWR_LED This connects to the power bu.
Installation Page 3-15 3-6 T T T T T her her her her her mo Stic mo Stic mo Stic mo Stic mo Stic k Function (Optional) k Function (Optional) k Function (Optional) k Function (Optional) k Function (Optional) This mainboard is equipped with a digital thermometer capability to monitor any temperature.
Installation Page 3-17 3-9 ACPI S3 (Suspend T o RAM) Function This mainboard supports the STR (Suspend T o RAM) power management scheme by maintaining the appropriate power states in the RAM interface signals. The power source to the RAM is kept active during STR (ACPI S3).
Installation Page 3-17 3-9 ACPI S3 (Suspend T o RAM) Function This mainboard supports the STR (Suspend T o RAM) power management scheme by maintaining the appropriate power states in the DDR SDRAM interface signals. The power source to the DDR SDRAM is kept active during STR (ACPI S3).
Installation Page 3-18.
BIOS Page 4-1 Section 4 BIOS SETUP Main Menu The ROM BIOS contains a built-in Setup program which allows user to modify the basic system configuration and hardware parameters. The modified data is stored in a battery-backed CMOS, so that data will be retained even when the power is turned off.
BIOS Page 4-2 The main menu displays all the major selection items. Select the item you need to reconfigure. The selection is made by moving the cursor (press any direction (arrow key ) to the item and pressing the ‘Enter’ key.
BIOS Page 4-3 4-2 Advanced BIOS Fe atur es Selecting the “ADV ANCED BIOS FEA TURES” option in the CMOS SETUP UTILITY menu allows users to change system related parameters in the displayed menu. This menu shows all of the manufacturer ’ s default values for the board.
BIOS Page 4-4 Hyper-Threading T echnology Enables the CPU Hyper-Threading T echnology . Options: Enables, Disabled. It is recommend to enable Hyper-Threading T echnology on system with Windows XP and Linux 2.4 and disabling it for legacy OS.
BIOS Page 4-5 functionality. APIC is an Intel chip that provides symmetric multiprocessing (SMP) for its Pentium systems. Options: Enabled, Disabled. HDD S.M.A.R.T. Capability The S.M.A.R.T . (Self-Monitoring, Analysis, and Reporting T echnology) system is a diagnostics technology that monitors and predicts device performance.
BIOS Page 4-6 DRAM Timing Selectable For setting DRAM T iming, select By SPD to follow Intel PC DDR SDRAM Serial Presence Detect Specification. Options: Manual, By SPD. CAS Latency Time This item specifies the number of clock cycles needed after a Column Address Strobe (CAS) signal before data can be read.
BIOS Page 4-7 4-4 Integrated Peripherals Figur e 5: Integrated Peripherals Realtek Lan Boot ROM Enable/disable the onboard Realtek Lan Boot ROM for booting from LAN. Options: Enabled, Disabled. PCI Express Function Scroll to PCI Express Function and press <Enter>.
BIOS Page 4-8 Chipset IDE Devices Scroll to Chipset IDE Devices and press <Enter>. The following screen appears: Delay For HDD (Secs) This item allows you to set longer time stand by before system Scan HDD at post screen. Some HDD may need a longer stand by time before it can be detected.
BIOS Page 4-9 support Ultra DMA-33/66/100, select Auto to enable UDMA mode by BIOS. Options: Auto, Disabled. *** Chipest Serial A T A Setting *** Chipest Serial A T A This sets the mode of SA T A. Combined mode will force SA T A to replace one of the traditional IDE Primary or Secondary ports.
BIOS Page 4-10 USB Keyboard Support Enable/Disable support for USB keyboard under DOS. Options: Auto, Enabled, Disabled. USB Mouse Support Enable/Disable support for USB mouse under DOS. Options: Enabled, Disabled. High Definition Audio (Intel ® High Definition Audio Controller) This item allows you disable the on-chip Audio.
BIOS Page 4-11 Parallel Port Mode This field allows the user to select the parallel port mode. Options: SPP, EPP, ECP, ECP+EPP. EPP Mode Select This field allows the user to select the EPP mode for parallel port mode. Options: EPP1.9, EPP1.7. ECP Mode USE DMA This field allows the user to select DMA1 or DMA3 for the ECP mode.
BIOS Page 4-12 4-5 Power Management Setup Choose the “POWER MANAGEMENT SETUP” in the CMOS SETUP UTILITY to display the following screen. This menu allows the user to modify the power management parameters and IRQ signals. In general, these parameters should not be changed unless it’ s absolutely necessary .
BIOS Page 4-13 PCI Express PME PCI-E device PME function. Options: Enabled, Disabled. Power Management Use this to select your Power Management selection. The default is User define. Max. saving : Maximum power savings. Inactivity period is 1 minute in each mode.
BIOS Page 4-14 W ake-Up by PCI Card An input signal form PME on the PCI card awakens the system from S3 suspend state. Options: Enabled, Disabled. Power On by Ring When enabled, any modem activity awakens the system from soft-off state. Options: Enabled, Disabled.
BIOS Page 4-15 4-6 PNP/PCI/PCI-E Configuration This page lets the user to modify the PCI/PCI-E IRQ signals when various PCI/ PCI-E cards are inserted. W ARNING: Conflicting IRQ’s may cause system unable to locate certain devices. Figur e 7: PNP/PCI Configuration Setup Resources Controlled By Determines what controls system PNP/PCI resources.
BIOS Page 4-16 Interrupt requests are shared as shown below: 4-7 PC Health Status Figur e 8: PC Health Status Show PC Health in POST When this function is enabled the PC Health information is displayed during the POST (Power On Self T est). Options: Enabled, Disabled.
BIOS Page 4-17 Current System/CPU T emperature Displays the current system/CPU temperature. Thermo Stick T emperature Displays the current thermo Stick temperature. Current CPU/Chassis/Power F AN Speed Displays the current speed of the CPU, chassis, and power fan speed in RPMs.
BIOS Page 4-18 SmartFan Function Scroll to SmartFan Function and press <Enter>. The following screen appears: Smart CPU F AN Function This item selects how the fan speed should be set. Full speed fixes fan speed at100% duty cycle. Control the Fan by Duty-Cycle directly .
BIOS Page 4-19 4-8 Po wer BIOS Fe atures This page lets you adjust various parameters to obtain improved performance for overclocking. W arning : Overclocking requires expert knowledge and risks permanent damage to system components. W e recommend you leave these parameters at their default values for proper operation.
BIOS Page 4-20 CPU CLOCK/SPEED Enables you to increment the CPU’ s clock generator at 1MHz step. This works together with CPU Clock Ratio (below) to set the CPU operating frequency. CPU Clock Generator x CPU Clock Ratio = CPU Frequency For example, if you have a processor that is rated at 2.
BIOS Page 4-21 PCI Freq Sel Enables you to select the PCI Frequency. Options: Sync., 37.5MHz, 40MHz, 33.3MHz. System Memory Frequency Enables you to select a ratio of the DDR2 DRAM to match the installed DRAM frequency . W e recommend that you leave this item at the default value.
BIOS Page 4-22 Chipset V oltage This item allows you to adjust the Chipset voltage. Options: -0.00V to +0.30V in 0.1V increments. W e recommend that you leave this at the default value. VDIMM V oltage This item allows you to adjust the DIMM slot voltage.
BIOS Page 4-23 4-10 Super visor/User Pass word Setting This function lets you set either Supervisor or User Password, or both, to prevent unauthorized changes to BIOS menus. supervisor password: full rights to enter and change options of the setup menus.
BIOS Page 4-24 4-11 Exiting BIOS Save & Exit Setup Pressing <Enter> on this item asks for confirmation: Save to CMOS and EXIT (Y/N)? Y Pressing “Y” stores the selections made in the menus in CMOS – a special section of memory that stays on after you turn your system off.
Drivers Installation Page 5-1 Section 5 DRIVER INST ALLA TION Easy Driver Installation Insert the bundled CD into the CD-ROM and the main menu screen will appear. The main menu displays links to the supported drivers, utilities and software. Method 1 This item installs all drivers automatically.
Drivers Installation Page 5-2 Realtek Sound Manager Quick User-guide Introduction To obtain the best performance from your audio system, run the "Sound Manager" utility to adjust the settings to suit your needs. This section of the manual is intended to provide a quick user-guide to setup "Sound Manager".
Drivers Installation Page 5-3 Speaker Configuration: <Figure 3> 3 . This page displays the mainboards's phone jack function when a corresponding audio mode is selected. Figure 3 above shows the phone jack setup for 8 channel mode. 4 . This page lets you test the 3D Positional Audio features.
Drivers Installation Page 5-4 <Figure 6> SPDIF: 6 . This page shows S/PDIF-Out function on your system. S/PDIF-Out: Choose the type of audio source that will appear on the S/PDIF- out connector. 5 . This page displays information regarding the audio hardware and software.
Drivers Installation Page 5-5 7 . This mainboard is equipped with jack re-tasking feature for Front Panel audio. Simply plug Microphone/ Line-out into any front panel jack and it will work. <Figure 7> Audio Wizard: 8 . Figure 8 below shows the back panel audio.
Drivers Installation Page 5-6.
Appendix A-1 Appendix A A-1 Flashing the BIOS Download the xxxxx.EXE file corresponding to your model from our website to an empty directory on your hard disk or floppy. Run the downloaded xxxxx.EXE file and it will self extract. Copy these extracted files to a bootable floppy disk.
Appendix A-2 5. Key in File Name to save previous BIOS to file. 6. T o confirm and proceed, please key in [Y] to start the programming. 7. The BIOS update is finished. xxxxx.bin F1 : Reset F10 : Exit XXXXX XXXX xxxxx.bin xxxxx.bin XXXXX XXXX xxxxx.bin xxxxx.
Appendix B-1 Appendix B B-1 POST CODES POST (hex) DESCRIPTION CF h T est CMOS R/W functionality . C0h Early chipset initialization: - Disable shadow RAM - Disable L2 cache (socket 7 or below) - Program basic chipset registers C1h Detect memory - Auto-detection of DRAM size, type and ECC.
Appendix B-2 18h Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586 or 686). 19-1Ah Reserved 1Bh Initial interrupts vector table. If no special specified, all H/W interrupts are directed to SPURIOUS_INT_HDLR & S/W interrupts to SPURIOUS_soft_HDLR.
Appendix B-3 43h T est 8259 functionality . 4 4 h Reserved 45-46h Reserved 4 7 h Initialize EISA slot 4 8 h Reserved 4 9 h 1 . Calculate total memory by testing the last double word of each 64K page. 2 . Program writes allocation for AMD K5 CPU. 4A-4Dh Reserved 4E h 1.
Appendix B-4 6E h Reserved 6Fh 1. Initialize floppy controller 2 . Set up floppy related fields in 40:hardware. 70-72h Reserved 7 3 h (Optional Feature) Enter A WDFLASH.EXE if : -A WDFLASH is found in floppy drive. -AL T+F2 is pressed 7 4 h Reserved 7 5 h Detect & install all IDE devices: HDD, LS120, ZIP, CDROM….
Ein wichtiger Punkt beim Kauf des Geräts Intel I945P (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Intel I945P noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Intel I945P - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Intel I945P reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Intel I945P erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Intel I945P besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Intel I945P verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Intel I945P. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Intel I945P gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
