Benutzeranleitung / Produktwartung Celeron M Half Size CPU Card With VGA/LAN des Produzenten Intel
Zur Seite of 82
USER ’ S MANUAL PCI-471LF Celeron ® M Half Size CPU Card With VGA/LAN PCI-471LF M2.
Copyright Notice PCI-471LF Celeron® M Hal Size CPU Card With VGA /LAN OPERATION MANUAL COPYRIGHT NOTICE This operation m anual is meant to assist bot h Embedded Computer manufacturers and end users in inst alling and setting up the system. The information contained in this document is subject to change without any notice.
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to provide reasonable protection against harm ful interference when the equ ipment is operated in a comm ercial environment.
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ...........
Contents 2-29 PCI Slot 3.3V Voltage Selection ..….............................. 2-21 2-30 Inverter Connector …………………………………….. 2-21 2-31 Reset / NMI / Clear Watchdog Selection ……………… 2-22 2-32 AT/ATX Power Selection …………………………….
Contents APPENDIX A EXPANSION BUS PCI Bus Pin Assignment ..............................................…......... A-2 EPCI Connector ..........................………....................….......... A-3 Compact Flash Card Conn ector Pin Assignm ent …………….
Page:1-1 INTRODUCTION This chapter gives you t he information for PC I-471LF. It also outlines the System specification. Section includes: z About This Manual z System Specifications z Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start.
Chapter 1 Introduction Page: 1-2 PCI-471LF USER ′ S MANUAL 1-1. ABOUT THIS MANUAL Thank you for purchasi ng our PCI-471LF Intel ® Celeron® M Half Si ze Card enhanced with VGA / LAN, which is ful ly PC / AT compatible. PCI-471LF provides faster processin g speed, greater exp andability and can handle more task than before.
Chapter 1 Introduction PCI-471LF USER ′ S MANUAL Page: 1-3 1-2. SYSTEM SPECIFICATION z CPU : Intel® Celeron® M processor ULV Celeron M 600MHz, without L2 cache System bus frequency at 400MHz Auto detect voltage regulat or z SYSTEM CHIPSET : Intel® 852GM chipset z MEMORY : Supports up to 1GB DDR266 SDR AM.
Chapter 1 Introduction Page: 1-4 PCI-471LF USER ′ S MANUAL z DISPLAY : Built in Intel 852GM, support CRT, LVDS (18 bit). z IDE INTERFACE : One IDE ports support up to four IDE devices. Supports UDMA 33/66/100. z FLOPPY DISK DRIVER INTERFACE : Supports up to two Floppy Di sk Drives, 3.
Chapter 1 Introduction PCI-471LF USER ′ S MANUAL Page: 1-5 z INTERRUPT CONTROLLERS : 82C59 x 2 z INTERRUPT LEVELS : 15 z OPERATING TEMPERATURE : 0 to 60 ° C (32 ° F to 140 ° F) z INPUT POWER REQUIREMENT : ATX power: +5V, +12V. AT power: z BOARD DIMENSION : 185mm x 122mm (7.
Page 2-1 HARDWARE CONFIGURATION ** QUICK START ** CHAPTER 2 Helpful informati on describes the jumper & connector settings, and component locati ons.
Chapter 2 Hardware Config uration Page: 2-2 PCI-471LF USER ′ S MANUAL 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM Port Connector ..........
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-3 2-2. COMPONENT LOCATIONS PCI-471LF Connector, Jumper and Component locations.
Chapter 2 Hardware Config uration Page: 2-4 PCI-471LF USER ′ S MANUAL 2-3. HOW TO SET THE JUMPERS You can configure your board by setti ng jumpers. Jum per is consists of two or three met al pins wi.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-5 JUMPER DIAGRAMS 2 pin Jumpe r loo ks l i ke t his Ju mper Ca p looks like this 3 pin Jumpe r loo ks l i ke t his Ju mper Bl ock .
Chapter 2 Hardware Config uration Page: 2-6 PCI-471LF USER ′ S MANUAL 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 NDCDA 2 NSINA 3 NSOUTA 4 NDTRA 5 GND 6 NDSRA 7 NRTSA 8 NCTSA 9 NRIA 10 NC COM2 : COM2 Connector The COM2 is selectable as R S-232/422/485.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-7 2-5. COM1 RI & VOLTAGE SELECTION JP6 : COM1 RI & Voltage Selection The selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION RI 1-2 VCC12 3-4 VCC 5-6 ***Manufacturing Default – R I.
Chapter 2 Hardware Config uration Page: 2-8 PCI-471LF USER ′ S MANUAL 2-6. COM2 RI & VOLTAGE SELECTION JP7 : COM2 RI & Voltage Selection The selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION RI 1-2 VCC12 3-4 VCC 5-6 ***Manufacturing Default – R I.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-9 2-7. RS232/422/485 (COM2) SELECTION JP8 : RS-232/422/485 (COM 2) Selection This connector is used to set the COM 2 function.
Chapter 2 Hardware Config uration Page: 2-10 PCI-471LF USER ′ S MANUAL 2-8. KEYBOARD OR PS/2 MOUSE CONNECTOR DIN : Keyboard or PS/2 M ouse Connector DIN connector can support keyboard, Y-cable, or PS/2 M ouse, user may select the right device to used on “Keyboard or PS/2 M ouse Selection”.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-11 2-10. EXTERNAL KEYBOARD CONNECTOR EXKB1 : External Keyboard Connector The pin assignment is as follows : PIN ASSIGNMENT 1 L _ KCLK 2 L _ KDAT 3 GND 4 PS2V5 2-11. RESET CONNECTOR JPAENL (9,11) : Reset Connector.
Chapter 2 Hardware Config uration Page: 2-12 PCI-471LF USER ′ S MANUAL 2-13. ATX POWER BUTTON JPANEL (10,12) : ATX Power Button The pin assignment is as follows : PIN ASSIGNMENT 10 PULL HIGH 12 PWB_SIOJ 2-14.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-13 2-16. KEYLOCK CONNECTOR JPAENL (13,14) : Keylock Connector The pin assignment is as follows: PIN ASSIGNMENT 13 KEYLOCK 14 GND 2-17.
Chapter 2 Hardware Config uration Page: 2-14 PCI-471LF USER ′ S MANUAL 2-19. SYSTEM FAN CONNECTOR JSFAN1 : System Fan connector The pin assignment is as follows: PIN ASSIGNMENT 1 GND 2 +12V 3 FAN0 2-20.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-15 2-21. VGA CONNECTOR VGA : VGA CRT Connector The pin assignments are as follows: PIN ASSIGNMENT 1 RED 2 GREEN 3 BLUE 4 NC 5 GND .
Chapter 2 Hardware Config uration Page: 2-16 PCI-471LF USER ′ S MANUAL 2-22. HARD DISK DRIVE CONNECTOR IDE1: Hard Disk Drive Connector The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNME.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-17 2-23. FLOPPY DISK DRIVE CONNECTOR FDD1 : Floppy Disk Drive Connector You can use a 34-pin daisy-chain cable to connect two-FDDs. On one end of this cable is a 34-pin fl at cable to attach the FDD on the board, and the other side is attaches two FDDs.
Chapter 2 Hardware Config uration Page: 2-18 PCI-471LF USER ′ S MANUAL 2-24. PRINTER CONNECTOR PRNT1 : Printer Connector As to link the Printer t o the card, you need a cable to connect both DB 25 connector and parallel port.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-19 2-25. UNIVERSAL SERIAL BUS CONNECTOR USB1: Universal Serial Bus Connector The pin assignments are as follows: PIN ASSIGNMENT 1 VCC 2 USBC0N 3 USBC0P 4 GND 5 GND 6 VCC 7 USBC1N 8 USBC1P 9 GND 10 GND 2-26.
Chapter 2 Hardware Config uration Page: 2-20 PCI-471LF USER ′ S MANUAL 2-27. ATX POWER CONNECTOR PW1 : ATX Power Connector The pin assignments are as follows: PIN ASSIGNMENT 1 VCC 2 VCC 3 GND 4 GND 5 VCC12 6 V5SB 7 VCC 8 GND 9 PS_ON 10 VCC12J 2-28.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-21 2-29. PCI SLOT 3.3V VOLTAGE SELECTION JP9 : PCI Slot 3.3V Voltage Sel ection. The selections are as follows: FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION 3.3V from Mainboard 1-2 3-4 1 2 3 4 3.
Chapter 2 Hardware Config uration Page: 2-22 PCI-471LF USER ′ S MANUAL 2-31. RESET/NMI/CLEAR WATCHDOG SELECTION JP2 : Reset/NMI/C lear Watchdog Selection The selections are as follows: FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION RESET 1-2 JP2 NMI 3-4 JP2 CLEAR WATCHDOG 5-6 JP2 SMI 9-10 JP2 ***Manufacturing Default is set as open.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-23 2-32. AT/ATX POWER SELECTION JP1, JP2 (1-2), JP15 : AT/ ATX Power Selection The selections are as follows: JUMPER SETTING (pin closed) FUNCTION JP1 JP2 (1-2) JP15 JUMPER ILLUSTRATION AT Open Close Close ATX Close Open Open ***Manufacturing Default is set as ATX.
Chapter 2 Hardware Config uration Page: 2-24 PCI-471LF USER ′ S MANUAL 2-33. LVDS CONNECTOR CNT3 : LVDS Connector. The pin assignments are as follows: 2 1 CN T 3 PIN ASSIGNMENT PIN ASSIGNMENT 1 LCD_.
Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-25 2-34. LVDS PANEL VOLTAGE SELECTION JP12 : LVDS Panel Voltage Selection. The selections are as follows: SELECTION JUMPER SETTING.
Page: 3-1 SOFTWARE UTILITIES This chapter comprises the detaile d inform ation of VGA driver, LAN driver, and Flash BIOS update . It also describes how to install the watchdog tim er configuration. Section includes: z VGA Driver Utility z Flash BIOS Update z LAN Driver Utility z Intel® Chipset Software Installation Utility z USB2.
Chapter 3 Software Configuration Page:3-2 PCI-471LF USER ′ S MANUAL 3-1. INTRODUCTION Enclosed with our PCI-471LF packag e is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes.
Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-3 3-2-1. Installation of VGA Driver: To install the VGA Driver, simp ly follow the following steps: 1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD ROM drive. 2. Under Windows 9X/NT4.
Chapter 3 Software Configuration Page:3-4 PCI-471LF USER ′ S MANUAL FLASH MEMORY WRITER v7.XX (C) Award Software 2001 All Ri ghts Reserved Flash Type – SST 49LF004A /3.
Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-5 FLASH MEMORY WRITER v7.XX (C) Award Software 2001 All Ri ghts Reserved Flash Type – SST 49LF004A /3.
Chapter 3 Software Configuration Page:3-6 PCI-471LF USER ′ S MANUAL 3-5. INTEL® C HIPSET SOFTWARE INSTALLATION UTILITY 3-5-1. Introduction The Intel® Chipset Software Installatio n Utility installs to the target system the Windows* INF files that outline to the operating system how the chipset components will be confi gured.
Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-7 3-6. USB2.0 SOFTWARE INSTALLATION UTILITY 3-6-1. Installation of Utility for Windows 98SE/ 2000/XP Intel USB 2.0 Enhanced Host Controller dri ver can only be used on Windows 98SE, Windows 2000 and Windows XP on Intel Desktop boards.
Chapter 3 Software Configuration Page:3-8 PCI-471LF USER ′ S MANUAL 3-7. WATCHDOG TIMER CONFIGURATION The I/O port address of the watchdog tim er is 2E(hex) and 2F(hex).
Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-9 Mov al, 07h ; Select Logical Device 8 of watchdog tim er Out dx,al Inc dx Mov al, 08h Out dx,al ;---------------------------------.
Page: 4-1 AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: z Introduction z Entering Setup z The Standard CMOS Features z The Advanced BIOS Features z The Advanced C.
Chapter 4 Award BIOS Setup Page: 4-2 PCI-471LF USER ′ S MANUAL 4-1. INTRODUCTION This chapter will show you the function o f the BIOS in managing the features of your system . The PCI-471LF Celeron® M Half Size CPU Card is equipped with the BIOS for system ch ipset from Award Software Inc.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-3 4-2. ENTERING SETUP When the system is powered on , the BIOS will enter th e Power-On Self Test (POST) routines and the following messa.
Chapter 4 Award BIOS Setup Page: 4-4 PCI-471LF USER ′ S MANUAL 4-3. THE STANDARD CMOS FEATURES Highlight t he 〝 STANDARD CMOS FEATURES 〞 and press the <ENTER> key and the screen will d isp.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-5 IDE Primary Master / Slav e: IDE Secondary Master / Slav e: The BIOS can automatically detect th e specificati ons and optimal operating mode of al most al l IDE hard drives.
Chapter 4 Award BIOS Setup Page: 4-6 PCI-471LF USER ′ S MANUAL LBA (Logical Block Addressing): During drive accesses, the IDE controller transforms the dat a address described by sector, head and cylinder number into a physical block address, significantly i mproving data transfer rates.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-7 HARD DISK ATTRIBUTES: Type Cylinders Heads V-P comp LZone Sect Capacity 1 306 4 128 305 17 10 2 615 4 300 615 17 20 3 615 6 300 615 17 .
Chapter 4 Award BIOS Setup Page: 4-8 PCI-471LF USER ′ S MANUAL 4-4. THE ADVANCED BIOS FEATURES Choose the 〝 ADVANCED BIOS FEATURES 〞 in the main menu, the screen shown as below.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-9 FIRST/SECOND/ BOOT DEVICE: The BIOS attempt to load the operating system from the devices in the sequence selected in these items.
Chapter 4 Award BIOS Setup Page: 4-10 PCI-471LF USER ′ S MANUAL OS SELECT FOR DRAM >64MB : Select the operating sy stem that is running with greater t han 64MB or RAM on the system. You m ay choose OS2 or Non-OS2. 4-5. ADVANCED CHIPSET FEATURES Choose the 〝 ADVANCED CHIPSET FEATURES 〞 fr om t he main men u, the screen shown as below.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-11 DRAM DATA INTEGRITY MODE: Select Parity or ECC (error-correcting c ode), according to the type of installed DRAM. SYSTEM BIOS CACHEABLE: Selecting Enabled allows caching of the system BIOS ROM at F0000h- FFFFFh, resulting in better system perform ance.
Chapter 4 Award BIOS Setup Page: 4-12 PCI-471LF USER ′ S MANUAL 4-6. INTEGRATED PERIPHERALS Choose 〝 INTEGRATED PERIPHERALS 〞 fro m th e ma in se tu p men u , a display will be shown o n screen .
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-13 VIA ONCHIP IDE DEVICE: The options for these item s are found in its sub m enu. By pressing the <ENTER> key, you are prom pt to .
Chapter 4 Award BIOS Setup Page: 4-14 PCI-471LF USER ′ S MANUAL hard drive and your system software bot h support Ultra DMA/33, select Auto to enable BIOS support. 4. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-15 SUPER IO DEVICE: The options for these item s are found in its sub m enu. By pressing the <ENTER> key, you are prom pt to enter .
Chapter 4 Award BIOS Setup Page: 4-16 PCI-471LF USER ′ S MANUAL This item allows you to select IR transmission routes, one is RxD2m, TxD2 (COM Port) and the other is IR-R x2Tx2 8. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-17 4-7. POWER MANAGEMENT SETUP Choose 〝 POWER MANAGEMENT SETUP 〞 option on the m ain me nu, a display will be shown o n screen as bel.
Chapter 4 Award BIOS Setup Page: 4-18 PCI-471LF USER ′ S MANUAL VIDEO OFF OPTION: When enabled, this feature allows the VGA adapter to operate in a power saving mode. Always On Monitor will remain on during power saving modes. Suspend --> Off Monitor blanked when the systems enters the Suspend mode.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-19 RESUME BY ALARM: When Enabled, your can set the date and tim e at which the RTC (real-time clock) alarm awakens the system from Suspend mode.
Chapter 4 Award BIOS Setup Page: 4-20 PCI-471LF USER ′ S MANUAL 4-8. PNP/PCI CONFIGURATION Choose 〝 PNP/PCI CONFIGURATION 〞 f ro m th e main men u , a d is pl ay will be shown on screen as below.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-21 RESOURCE CONTROLLED BY: The Award Plug and Play B ios can automat ically configure all of the booth and Plug and Play-compatible devices. However, this capability means absolutely nothing unl ess you are using a Plug and Play operating system such as Windows 95.
Chapter 4 Award BIOS Setup Page: 4-22 PCI-471LF USER ′ S MANUAL 4-9. PC HEALTH STATUS Choose 〝 PC HEALTH STATUS 〞 from the main menu, a display will be shown on screen as below: Phoenix - AwardB.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-23 VCORE: This item shows you the current system voltage. 3.3V / +5V / +12V / -12V / -5V: Show you the voltage of 3.
Chapter 4 Award BIOS Setup Page: 4-24 PCI-471LF USER ′ S MANUAL 4-11. LOAD FAIL-SAFE DEFAULTS By pressing the <ENTER> key on this item , you get a confirm ation dialog box with a message si mi.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-25 4-13. PASSWORD SETTING User is allowed to set eit her supervisor or user password, or both of them.
Chapter 4 Award BIOS Setup Page: 4-26 PCI-471LF USER ′ S MANUAL 4-14. SAVE & EXIT SETUP After you have complet ed adjusting all the sett ings as required, you m ust remember to save these setting into the CMOS RAM.
Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-27 4-15. EXIT WITHOUT SAVING If you wish to cancel any changes you have m ade, you ma y select the “EXIT WITHOUT SAVING” and the orig inal setting stored in the CMOS will be retained.
Page: A-1 EXPANSION BUS This appendix indicates the pi n assignments. Section includes: z PCI BUS Pin Assignment z PPCI BUS Pin Assignment z Compact Flash Ca rd Connector Pin Assignm ent APPENDIX A.
Appendix A Expansion Bus Page: A-2 PCI-471LFUSER ′ S MANUAL PCI BUS PIN ASSIGNMENT Like ISA-BUS connector, the PCI-BUS edge connector i s also divided into two sets: one consists of 98-pi n; the other consists of 22-pi n.
Appendix A Expansion Bus PCI-471LF USER ′ S MANUAL Page: A-3 EPCI CONNECTOR You will find a EPCI connector in our PCI-471LF. The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNMENT A1 GND .
Appendix A Expansion Bus Page: A-4 PCI-471LFUSER ′ S MANUAL COMPACT FLASH CARD CONNECTOR PIN ASSIGNMENT The pin assignments of Compact Flash Card connector are stated below.
Page: B-1 TECHNICAL SUMMARY This section introduce you the m aps concisely. Section includes: z Block Diagram z Interrupt Map z RTC & CMOS RAM Map z Timer & DMA C hannels Map z I / O & Mem.
Appendix B Technical Summary Page: B-2 PCI-471LF USER ′ S MANUAL BLOCK DIAGRAM.
Appendix B Technical Summary PCI-471LF USER ′ S MANUAL Page: B-3 INTERRUPT MAP IRQ ASSIGNMENT 0 System TIMER 1 Keyboard 2 Cascade 3 Serial port 2 4 Serial port 1 5 Available 6 Floppy 7 Parallel port.
Appendix B Technical Summary Page: B-4 PCI-471LF USER ′ S MANUAL RTC & CMOS RAM MAP CODE ASSIGNMENT 00 Seconds 01 Second alarm 02 Minutes 03 Minutes alarm 04 Hours 05 Hours alarm 06 Day of week .
Appendix B Technical Summary PCI-471LF USER ′ S MANUAL Page: B-5 TIMER & DMA CHANNELS MAP Timer Channel Map : Timer Channel Assignment 0 System timer interrupt 1 DRAM Refresh request 2 Speaker t.
Appendix B Technical Summary Page: B-6 PCI-471LF USER ′ S MANUAL I/O & MEMORY MAP Memory Map : MEMORY MAP ASSIGNMENT 0000000-009FFFF Sy stem memory used by DOS and application 00A0000-00BFFFF Display buffer memory for VGA/ EGA / CGA / MONOCHROME adapter 00C0000-00DFFFF Reserved for I/O device BIOS ROM or RAM buffer.
Ein wichtiger Punkt beim Kauf des Geräts Intel Celeron M Half Size CPU Card With VGA/LAN (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Intel Celeron M Half Size CPU Card With VGA/LAN noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Intel Celeron M Half Size CPU Card With VGA/LAN - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Intel Celeron M Half Size CPU Card With VGA/LAN reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Intel Celeron M Half Size CPU Card With VGA/LAN erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Intel Celeron M Half Size CPU Card With VGA/LAN besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Intel Celeron M Half Size CPU Card With VGA/LAN verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Intel Celeron M Half Size CPU Card With VGA/LAN. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Intel Celeron M Half Size CPU Card With VGA/LAN gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
