Benutzeranleitung / Produktwartung Arima LH500 des Produzenten Intel
Zur Seite of 78
1 LH500 USER MANUAL Arima Computer Corp. Building Your Competitive Advantage.
2 TABLE OF CONTENTS: LEGAL DISCLAIMER... ... ............. ... ............. ... ............. ... ............. ... ............. ... ............. . 4 COPYRIGHT NO TI CE ............. .. .............. .. .............. ............. ... ...........
3 3.2 U SING S ETUP ... ............. ................ .............. ............. ................ ............. .............. .... 46 3.3 T ROUBLESHOOTING ......... ............. .............. ................ ............. ............. ........
4 Legal Disclaimer The information provided in this do cument is subject to change without notice. Arima Computer Corp. makes no warranty re garding this document.
5 Technical Support If a problem arises with you r system during installation or operation and is unable to be resolved from the user manual, consult the following list of resources f or help: Contact the place of purchase for help. This is th e recommended solution as they can provide the quickest assistance.
6 Safety Instruc tion Keep this manual for f uture reference. Keep the equipments in a safe, cool, dry p lace. Perform the installation on a dry, flat surface. Ground yourself by touching a plugged-in power supply, which displaces static elect ricity.
7 Chapter 1. Getting Started 1.1 Congratula tions You have in possession one of the m ost powerful and versatile Dual Intel Xeon processor solutions, the LH500.
8 1.2.1 Quick Installation Guide CN8 PCI-X Slot 1 Speed Select Jumper Open Short 133 MHz Enabled (defau lt) 100 MHz Enabled CN29 COM2 Header CN52 LED Board CN7 PCI-X Slot 2 Speed Select Jumper Open Sh.
9 1.3 Featur es Highlight CPU: Supports high productivity Dual and Single Intel Xeon processors configuration LH500 does not support Prestonia 533MHz CHIPSET: Runs state of the art Intel 7.
10 1.4 Motherboard Specificatio n Processors Dual m PG604 ZIF so cket Dual onboard 4-phase VRD (VRM 10.1 Spec.) Supports one or two Intel Xeon processors with 1MB of integrated L2 cache .
11 Intel 82546GB Anvik2 dual channel Gigabit Ethernet Controller Two RJ-45 connectors with LEDs PXE option ROM solution Two 4-pin headers for front panel LED output Integrated Graphics Controller ATI RAGE XL PCI graphics controller 8MB Frame Buffer of video memory ICH5 USB 2.
12 1.5 Motherboard Layout [major components] The following diagram indicates all the major components of the motherboard. Alternative use of PCI-X Slot 2: For the LH500-V model, PCI-X Slot 2 ca n be used for 1U/2U riser card and Adaptec ZCR (zero channel RAID) card.
13 1.6 Hardware Mo nitor Two kinds of hardware monitoring are provided with the motherboard. An ADM 1026 chip is used to provide dedicated monitoring of voltages, temperatures and f an RPM. Specifically, it monitors CN30 and CN48’s vol tages, CPU1 and CPU2’s temperatures, and finally, CN36 and CN39’s RPM.
14 Chapter 2. Hardw are Installation 2.1 Mounting the motherboard !INSTALLATION WARNING! Use Caution When Installing the ServerBoard into the System Chassis The components underneath the PS/2 Mouse/ K.
15 2.2 Installing the processor LH500 operates best when dual Intel Xeo n processors are in use. When using only on e processor, install it in CPU_1 socket. We discourage you from installing in th e CPU_2 socket if you have only one processor to install.
16 A good quality backplate should hav e tape over some parts of it that prevents electrical damage. When ever possible, use high quality backplates to prolong the life of your m otherboard. 2. Lift up the lever and locate the trian gle marking on the CPU and CPU socket.
17 3. Place the CPU wit h the correct orientation (B) as shown in the f ollowing pictures. The lever is still u p and the two triangl es are in the same corner. The CPU will not f it if the orientation is wrong. Do not try t o force the CPU into the socket; i t could result in irreparable damage to the CPU.
18 4. Lower the socket locking lever in place. 5. Now, rest the motherboard in to the chassis, align the four holes of the backplate with the four bolts of the chassis. We do not recommend you to apply thermal grease at this poi nt of the installation.
19 6. Mount the CPU heatsink to th e top of the CPU and socket. Ali gn the screws of the heatsink with th e four holes of the backplate and th e chassis bolts, then fasten them secu rely. Repeat the steps for the i nstallation of another CPU. Heatsink not included in t he package.
20 2.3 Installing the memory 2.3.1 DIMM combination The following diagram indicates the locations of memory sockets, captioned 1 st _Pair_ A th rough 3 rd _Pair_B. Types of memory supported: Six sockets of 184-pin 2.5Volt DDR DIMM supporting DDR-333/ 266.
21 DDR memory types are determined by two facto rs: speed and rank. LH500 supports DDR 333/266 speed in both single/dual rank. The rank of your memory could impact the effectiveness of the m otherboard. Table 1 indicates the setup that LH500 h as been tested on.
22 2.3.2 Installing DIMM modules 1. Open up the brackets: 2. Line up the memory with socket. Make sure the gap fits into the socket..
23 3. Push in the mem ory stick until bracket can be closed securel y onto the stick. Make sure the b rackets hold on to the memory modul e. These pictures only show one m emory stick but remember to install them in pairs .
24 2.4 Jumpers Configuration 2.4.1 Clear CMOS header Header CN19 controls CMOS setting. Posit ion your motherboard as it appears in the following diagram . Pin 1 is on the side of PCI slots, whereas pin 3 is on the side of the power supply connectors.
25 2.4.2 Enable onboard VGA heade r Header CN25 controls the onboard VGA setting. When CN25 is open, no jum per, VGA is enabled. When CN25 is on , VGA is disabled.
26 2.4.3 PCI-X Slot 1 Jumper Setting: Header CN8 controls PCI-X Slot 1 sett ing. When CN8 is open, slot 1 is set to 133 MHz. When CN8 is on, slot 1 is set to 100MHz. The frequencies describe here are maximum operating frequencies. If PCI-X channel is shared with other devi ces, then maximum operating frequency cannot be achieved.
27 2.4.4 PCI-X Slot 2 Ju mper: Header CN7 controls PCI-X Slot 2 sett ing. When CN7 is open, no jumper, slot 2 is set to 133MHz. When CN7 is on, slot 2 is set to 1 00MHz. The frequencies describe here are m aximum operating frequencies. If PCI-X channel is shared with other devices, the n maximum operating frequency cannot be achieved .
28 2.4.5 PCI-X Slot 5 Ju mper: Header CN9 controls PCI-X Slot 5 sett ing. When CN9 is open, no jumper, slot 5 is set to 133MHz. When CN9 is on, slot 5 is set to 1 00MHz. The frequencies describe here are m aximum operating frequencies. If PCI-X channel is shared with other devices, the n maximum operating frequency cannot be achieved .
29 2.4.6 LAN 82546GB Header CN49 controls the LAN 82546GB activation. W hen CN49 is open, no jumper, LAN 8254 6GB is enabled. When CN49 is on, LAN825 46GB is disabled.
30 2.5 Power Supply 2.5.1 ATX 24-pin power connector There are two 24 pin power connecto rs on the motherboard. Only one is needed to make the motherboard operational. The redundan cy is built-in for your convenience; you may choose either one to h ook up depending on the layout of your system chassis.
31 Make sure the AC adapter is not plugged into the wal l outlet during installation. The electric current co uld damage the motherboard..
32 2.5.2 ATX 8-pin power conne ctor The 8-pin connector provides dedicat ed power to the CPU. Refer to the following diagram for its location and configuration.
33 2.6 Cables & Connectors 2.6.1 Floppy disk drive connector The following diagram indicates the location of the flo ppy drive connector: To install the floppy drive, first ref er to the instructions that come with th e floppy drive. Then consult the instructions here.
34 Diagnosing an incorrectly installed flo ppy drive Drive is not automatically detected. Usually caused by faulty cables, cables put i n backwards or a bad floppy drive or m otherboard. Try another floppy drive to verif y the problem if the cable is properly installed or try replacing the actual cable.
35 2.6.2 IDE connectors The following diagram indicates the location of the IDE co nnectors: As always, read the in structions that come with the IDE drive an d then consult the instructions here. For Parallel ATA, installing ID E drives has become simpler over the years.
36 2.6.3 Front Panel Connectors You can find the pin num ber on the corner of the pin block. Pi n 2 is located closer to the oute r edge of the motherboard than pin 1. Pin 34 is closer to the outer edge of the m otherboard than pin 33. The red + indicates the an ode, or the +5V.
37 Power LED: This 3-pin connector attaches to the pow er LED. HDD Act ivity LED: This 2-pin connector attaches to the LED of the hard disk. The LED lights up when HDD is active. Power Switch: This 2-pin connector attaches to the pow er button of the system.
38 2.6.4 Rear Pa nel I/O ports The following illustration displays the motherboard I/O po rt array. Type of Port Function PS/2 Mouse connector The system will direct IRQ12 to the PS/2 mouse if one is detected. If not detected, IRQ12 can be used for expansion slot.
39 2.6.5 Back Pa nel LAN LED Back P anel LA N LED: header CN52 and CN53 control front panel LAN LED setting s. It allows the user to monitor LAN activities from the f ront of the system .
40 2.6.6 Front Panel LAN LED Connector Header CN52 controls the front panel LAN LED activati on. Front panel LAN LED are meant to show link and activity. When link is established, the LED stays on . When LAN transfer is in progress, the LED flashes. To activate the front panel LAN LED, connect the LED wires to CN52.
41 2.6.7 System Speaker Connector Header CN46 controls the speaker activation. To activate the system sp eaker, connect the speaker wire to CN46. Refer to the following diagram for the location of CN46 .
42 2.6.8 Front USB Connec tor Header CN23 controls the two front USB connections. To activate the front USB, conn ect the two USB wire to CN23. Each USB wire requi res 4 pins; CN23 has 9 pins, therefore supports two USB connections. The one ex tra pin is for chassis ground use.
43 Side A shares th e same bus as USB A, therefore two USB devices cannot use side A and USB A tog ether. Only one device will w ork at a time . The same goes for Side B an d USB B.
44 2.6.9 Front Panel Se rial Port Connect or Header CN29 controls the activation of front panel s erial port. In the specification, front panel serial port i s COM2, the back panel is COM1. Refer to the fol lowin g diagr am for lo catio n and or ientat ion of C N29.
45 CHAPTER 3. BIOS SETUP This chapter discusses the PhoenixBIOS setup program built into th e ROM BIOS. BIOS is the basic input/output system , the firmware on the motherboard that enabl es the hardware to interface with the software. The setup program allows the users to modify the basic system configurations according to their needs.
46 3.2 Using Setup The following table provides details about how to navigate the Setup program using keyboard. KEY FUNCTION Up Arrow ↑ Move to the previous item. Down Arrow ↓ Move to the next item. Left Arrow ← Move to the previous menu. Right Arrow → Move to the next menu.
47 3.3 Troubleshooting In case the system cannot be boo ted after some changes in BIOS, use the clear CMOS jum per setting to reset the BIOS to default. To avoid such problem, configure only the items that you tho roughly understand and refrain from modifying the default chipset setting s.
48 3.4 Main Menu: PhoenixBIOS Setup Utility Main Advanced Sec urity Power Bo ot Exit Item Specif ic Help System Ti me [1 2:59:59] System D ate [11/30/2002 ] Legacy Di skette A: [1.44/1 .25 MB 3 ½ ] ► IDE Pri./ATA Ma ster [200GB] ► IDE Pri./ATA Sla ve [None] ► IDE Sec.
49 3.4.1 IDE Chan nel sub-menu: When there is a drive install ed on an IDE or SATA, the sub men u will look like the followi ng: PhoenixBIOS Setup Utility Main IDE Pri.
50 Transfer Mode Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 Fast PIO 4 FPIO 3/ DMA 1 FPIO 4/ DMA 2 Select the m ethod f or moving data to/from the drive. Autotype the drive to select the optim um transfer mode. Ultra DMA Mode Disabled Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Selects the Ultra DMA m ode used for moving data to/from the drive.
51 3.4.2 Boot F eature sub-m enu: PhoenixBIOS Setup Utility Main Boot Features Item Specif ic Help Floppy check: [Disabled] Summary scre en: [Disabled] Boot-time Diagnostic Scr een: [Enabled] QuickBoot Mode: [En abled] Extended Memory Testing: [Just Zero it] Enable d Verif ies floppy type on boot; disabled speeds boot.
52 3.5 Advanced Menu: PhoenixBIOS Setup Utility Main Advanced Security Powe r Boot Exit Item Specif ic Help Multiprocessor Spec ification [1.4] Installed O/S: [WIN2000] Reset Con figuration Data: [NO].
53 Para llel AT A Disa bled Channel 0 Channel 1 Both Enable the PATA. Serial ATA Disabled Enabled Enable the SATA. Native Mode Operation Auto Parallel ATA Serial ATA Both Choose Native Mode for AT A. Note: Certain OS is not supported under native mode.
54 3.5.1 Advanced Chipset Sub M enu The Advanced Chipset Control Sub Menu looks lik e the following: PhoenixBIOS Setup Utility Advan ced Advanced Chipset Control Item Specif ic Help ► PCI Express De.
55 3.5.2 PCI Express Device Control Sub M enu The PCI Express Device Control Sub Menu looks lik e the following: PhoenixBIOS Setup Utility Advan ced PCI Express Device Control Item Specif ic Help Forc.
56 3.5.3 Advanced Pr ocessor Options Sub Menu The Advanced Processor Options Sub Men u looks like the following: PhoenixBIOS Setup Utility Advan ced Advanced Processor Options Item Specif ic Help Hyper Threa ding Technology [Enabled] Enabl es 2 nd Logical Processor.
57 3.5.4 I/O Device Configuration Sub Me nu The I/O Device Configuration Sub Menu looks lik e the following: PhoenixBIOS Setup Utility Advan ced I/O Device Configuration Item Specif ic Help Serial por.
58 3.5.5 Console Redirection Sub Menu The Console Redirection Sub Menu looks like the f ollowing: PhoenixBIOS Setup Utility Advan ced Console Redirection Item Specif ic Help Com Port Addr ess [Disable d] Baud Rate [1 9.2K] Console Type [P C ANSI] Flow Control [CTS/ RTS] Console con nection [Direc t] Continue C.
59 3.5.6 IPMI Sub Menu The IPM I Sub Menu l ooks l ike the follow ing: PhoenixBIOS Setup Utility Advan ced IPMI Item Specif ic Help BMC/Scorpio Configuration IP Address [192.
60 Date Format to show MM DD YYYY DD MM YYYY YYYY MM DD Choose how you want the data field to be shown. Date Separator . / Choose which character to use in date entries. To learn more about the IP MI selections, refer to a separate Arima IPMI manu al for detailed usage.
61 3.6 Security Menu: PhoenixBIOS Setup Utility Main Advan ced Security Powe r Boot Exit Item Specif ic Help Supervisor Pa ssword Is: Clear User Pa ssword Is: Clear Set Supervi sor Password: [Enter] Set User Pa ssword: [ Enter] Supervisor Password controls access to the setup utility.
62 3.7 Power Menu: PhoenixBIOS Setup Utility Main Advan ced Security Po wer Boot Exit Item Specif ic Help Power Savin g: [Disabled] Power Button Behavior: [On/Off] Instant O ff [Di sabled] Suspend Mo de: [ Suspend] After Power Fa ilure: [Last St ate] Maxi mum P owe r Savings conserves the greatest amount of system powe r.
63 this state but remain in a lower power mode. If you choose Suspend then you also have the option of choose Save to Disk. After Power Failure Stay Off Last State Power On Sets the mode of operation IF an AC/Power Loss occurs.
64 3.8 Bo ot Menu: All the possible devices that you can boot from are automatically detected and listed on the page. The items with a ‘+’ in front of it indicates that the item is a category with more devi ces nested under it. You can use <Enter> to di splay the nested devices.
65 3.9 Exit Menu: PhoenixBIOS Setup Utility Main Advan ced Security Powe r Boot Exit Item Specif ic Help Exit Saving Changes Exit Disca rding Changes Load Setup Defaults Discard Changes Save Ch anges Exit System Setup and save your change s to CMOS .
66 Discard Changes If, during a Setup Session, you change your m ind about changes you have made and have not yet saved th e values to CMOS, you can restore the values you previously saved to CMOS.
67 3.10 About the Bo ot Utilities The MainBoard comes with the following boot utilities: Phoenix QuietBoot™: Phoenix QuietBoot displays a graphic il lustration rather than the traditional POST messages while keeping you informed of diagnostic problems.
68 When <F10> is pressed Press <F10> switch to the PO ST screen and take one of two actions: 1. If MultiBoot is installed, the boot process continues with the POST screen until the end of POST, and then displ ays the Boot First Menu, text-based with these options: A: Load the o perat ing sy stem f rom a boot d evice o f yo ur choice.
69 3.10.2 Phoenix MultiB oot Phoenix MultiBoot expands your boot options by letting you choose your boot device, which could be a hard disk, floppy disk, or CD ROM. You can select your boot device in Setup, or you can choose a different device each time you bo ot during POST by selecting your boot device in The Boot First Menu.
70 3.11 BIOS Flash Upgrade Utility Phoenix Phlash gives you the ability to upd ate your BIOS from a floppy disk without having to inst all a new ROM BIOS chip. Phoenix Phlash is a utility for "flashing" (copying) a BIOS to the Flash ROM installed on your com puter from a floppy disk.
71 APPENDIX I: Glossary ACPI (Advanced Configuratio n and Power Interfa ce): a power m anagem ent specification that allows the operating system to control the amount of power distributed to the comp uter’s devi ces. Devices not in use can b e turned o ff, reducing unnecessary power ex penditure.
72 Closed and open jumpers: jumpers and ju mpe r pin s are acti ve when the y ar e “on” or “closed”, and inactive when they are “off” or “open ”. CMOS (Complementary Metal-Oxide Semiconductors): chips th at hold the basic startup information for the BIOS.
73 ESCD (Extended System Configuration Data): a form at for storing i nformation about Plug-n-Play de vices in the system BIOS. This inf ormation helps pro perly config ure the system each tim e it boots. Firmware: low-level soft ware tha t controls th e system hardw are.
74 PCI-to-PCI bridge: allows you to connect multiple PCI devices onto one PC I slot. PnP (Plug-n-Play): a design standard that ha s become ascendant in the industry .
75 ZCR (Z ero Channel RAID): ZCR card provides RAID-5 solution by working with the onboard SC SI/SATA/SATA-I I chip throu gh spec ial PCI-X slot with In tel RAID IOS logic , thus lowering cost o f RAI.
76 APPENDIX II: Block Diagram For your convenience, we have included this block diagram to show the i nternal design of the motherb oard in order to be tter aid you in tr oubleshooti ng.
77.
78 APPENDIX III: FAQ.
Ein wichtiger Punkt beim Kauf des Geräts Intel Arima LH500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Intel Arima LH500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Intel Arima LH500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Intel Arima LH500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Intel Arima LH500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Intel Arima LH500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Intel Arima LH500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Intel Arima LH500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Intel Arima LH500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
