Benutzeranleitung / Produktwartung LPCI-COM232-4 des Produzenten IBM
Zur Seite of 24
10623 Roselle Street, San Diego, CA 92 121 • (858) 550-9559 • FAX (858) 550-7322 contactus@accesi o.com • www.accesio.com MODEL LPCI-COM-8SM LPCI-COM-4SM LPCI-COM232-8 LPCI-COM232-4 USER MANUAL FILE: MLPCI-COM-8SM.
Manual LPCI-COM-8SM 2.
Notice The information in this document is provided for reference only. ACCES does n ot assume any liability arising out of the application or use of the informat ion or products d escribed herein.
Warranty Prior to shipment, ACCES equipment is thoroughly insp ected and tested to applicable sp ecifications. However, should equipment failure occu r, ACCES assu res its customers that prompt service a nd support will be available.
Table of Contents Chapter 1: Introduction ................................................................................................. 6 Specifications ..............................................................................................
Chapter 1: Introduction This serial interface card was designed for effective m ultipoint transmission in any one of three modes o n each channel. These mo des are RS232, RS422 and RS485 (EIA48 5) protocol. The RS485 mode may be run in three manne rs.
Communication Mode The card supports Half-Du plex communications with a 2-wire cable conne ction. Half-Duplex allows traffic to travel in both directions, but only one way at a time. RS485 com munications commonly use the Half- Duplex mode since they share only a sin gle pair of wires.
Specifications Communications Interface • I/O Connection: 68 Pin HVDCI SCSI style -Connector • Serial Ports: Eight cable terminated shielded male D-sub 9-pin connectors with standard I BM AT connectors compatible with RS485 specifications • Character length: 5, 6, 7, or 8 bits.
PCI BU S VH DCI 6 8 PI N C ON NEC T O R WITH AU T O-R T S CIRCUI TRY Figure 1-1: Block Diagram (Only one serial channel shown) Manual LPCI-COM-8SM 9.
Chapter 2: Installation A printed Quick-Start Guide (QSG) is pa cked with the card for your convenience. If you’ve already performed the steps from the QSG, you may find this chapter to be redundant and may skip forward to begin developing your application.
Hardware Installation 1. Make sure to set switches and jump ers from eith er the Option Selection section of this manual or from the suggestions of SETUP.EXE. 2. Do not install card into the computer until the software has been fully installed. 3. Turn OFF computer power AND unplug AC power from the system.
Chapter 3: Option Selection To help you locate the jumpers describ ed in this sect ion, refer to the Option Selection Map at t he end of this section. Operation of the serial communication s section is determined by jumper installat ion as described in the following p aragraphs.
Data Cable Wiring RS-485 SignalPin Connection Ain/out+ 2 Ain/out- 3 100 Ω to Ground 5 Baud Rate Ranges The jumper labeled CLK X8 provides a mean s to select baud rates in a higher range. When a jumper is not placed on the out the CLK X8 position, the baud ra te range is up to 115,200 baud.
6. 60" 2. 20" A B C D E F G BA UD x 8 H A B C D E F G H PO R T CO NFI G PO RT CO NFI G Figure 3-2: Option Selection Map The card has 8 separate channels which can b e individually configured.
Other jumpers: 1) RS 485 (2 wire mode ) - Two jumpers must be insta lled for each channel in thi s mode in order to connect the output and input lines. These jumpe rs are located near the cabl e connector and a re labeled with the channel letter and “485.
Chapter 4: Address Selection The card uses one address space. CO M A, COM B, COM C, COM D, COM E, COM F, COM G and COM H each occupy eight consecutive regi ster locations. The interrupt register which indicates whi ch port or ports caused the interrupt is located at base address + 64.
Chapter 5: Programming Sample Programs There are sample program s provided with the card in C, Pascal, QuickBASIC, and several Windows languages. DOS samples are located in the DOS directory and Win dows samples are located in the WIN32 directory. Windows Programming The card installs into Wi ndows as COM ports.
Address Map The core of the UART function is supplied by the EXAR XR16L788 chip. This chip is 16550 and 167 50 compatible, but has extra features that require communicating with an additional 8 registers per channel. Fo r instance, it is necessary to set the “Auto RTS” function.
Chapter 6: Connector Pin Assignments Input/Output Connections The card’s Serial Communications card use s eight individual 9-pin connectors, provided via a spider cable from a 68-pin HV DCI D-connector.
Appendix A: Application Considerations Introduction Working with RS422 and RS485 devices is not much di fferent from working with standard RS232 se rial devices and these two standards overcome defici enc ies in the RS232 standard. First, the cable length between two RS232 devices must be short; less tha n 50 feet at 9600 baud.
Parameter Conditions Min. Max. Driver Output Voltage (unloaded) 4V 6V -4V -6V Driver Output Voltage (loaded) LD and LDGND 2V jumpers in -2V Driver Output Resistan ce 50 Ω Driver Output Short-Circui .
RS485 Data Transmission The RS485 Standard allows a balanced transmissio n line to be shared in a party-line mode. As many as 32 driver/receiver pairs can share a two- wire party line network. Many characte ristics of the drivers and receivers are the same as in t he RS422 Standard.
Appendix B: HVDCI D-Connector Pinout Reference Connections will normally be made to the 9-pin con necto rs through the breakout cable. In case you wish to connect directly to the 68-pin connec tor, the pins translate as follows.
Customer Comments If you experience any problems with this manual or ju st want to give us some feedback, please email us at: manuals@accesio.com. Please detail any errors you find and in clude your mailing address so that we can send you any manual updates.
Ein wichtiger Punkt beim Kauf des Geräts IBM LPCI-COM232-4 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie IBM LPCI-COM232-4 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für IBM LPCI-COM232-4 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von IBM LPCI-COM232-4 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über IBM LPCI-COM232-4 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon IBM LPCI-COM232-4 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von IBM LPCI-COM232-4 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit IBM LPCI-COM232-4. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei IBM LPCI-COM232-4 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
