Benutzeranleitung / Produktwartung Infoprint M22 MFP des Produzenten IBM
Zur Seite of 62
IB M Inf o p rin t M2 2 M FP Op ti o n S etu p G ui d e S510-2633-00 IBM.
.
IB M Inf o prin t M2 2 M FP Op ti o n S etu p G ui d e S510-2633-00 IBM.
Edition: January 2003 MarkVision is a trademark of Lexmark Inter national, Inc., registered in the United States and/or other countries. Other trademarks are the proper ty of their respective o wners. © 2003 Lexmark International, Inc. All rights reserved.
Contents Step 1: Get started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Step 2: Assemble paper handling options . . . . . . . . . . . . . 4 Step 3: Set up the printer . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Step 4: Install the scanner .
Solve setup problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Maintain your scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Get started Step 1: Get star ted Using this book This book helps you set up y our pr inter and scanner (MFP option). If you do not ha ve an option listed here , you can skip that por tion of the setup guide and continue to the ne xt task.
Selecting a location f or y our printer and MFP Height Width Depth CA UTION: The printer weighs 20.4 kg (45 lb) and requires at least two people to lift it saf ely .
3 Get started Customizing y our MFP option Y ou can customize y our MFP with various input and memor y options. The printer base provides stability when configuring the pr inter plus input options.
Step 2: Assemb le paper handling options CA UTION: If you are using a 2000-sheet dra wer , a duple x unit with one or more input dra wers, or more than one 500-sheet dra wer , you must use either a printer stand or a caster base.
5 Place po wer adapter brack et (1) aside for later use . The other pow er adapter brac ket is not used with this scanner and can be discarded. Note: Be sure to set up the Use the f ollowing table to locate the instructions you need to set up items in the order listed in your printer and the paper handling options you purchased.
4 T urn the 2000-sheet draw er over so the bottom side is up . Dra wer bottom 5 Remov e the four scre ws and rubber feet from the bottom of the 2000-sheet dra wer . 6 Place the caster cov er on the bottom of the 2000-sheet dra wer . 7 Place the frame assemb ly inside the caster cover .
8 Inser t the two long machine scre ws from the caster base hardware bag thro ugh the scre w holes of the frame assemb ly and the caster cov er , and then into the holes in the bottom of the 2000-sheet dra wer . Each scre w goes through a lock w a sher , then a flat washer , then through the frame assembly and cov er .
Installing scre ws in the 2000-sheet dra wer Assembling the caster base f or the 500 or 250-sheet dra wer 1 Inser t two shor t stabilizer scre ws (2) into the pock ets of the 2000-sheet dra wer .
Installing scre ws in the 500-sheet dra wer and caster base Dra wer bottom 1 Remov e a 500-sheet dra wer from the car ton. 2 Remo v e all packing material and tape from the drawer and paper tra y . 3 If y ou are using a table or printer stand, then place the 500- sheet dra wer in that location and go to step 8, otherwise continue to step 4.
Installing additional 500- sheet dra wer s Installing 250- sheet dra wer s Dra wer bottom 1 Remov e a 500-sheet dra wer from the car ton. 2 Remo v e all packing material and tape from the drawer and paper tra y . 3 Use a flat tip scre wdr iv er to remov e the r ubber f eet from the bottom of the 500-sheet dra wer .
11 Assemble paper handling options 5 Place the dra wer on top of the previously installed dr awer or caster base. 6 Inser t two shor t stabilizer scre ws (2) into the pockets of the 250-sheet dra wer . The screws go through the dr awer and into the top of the screws of the pre viously installed dra wer or into the caster frame assemb ly .
12 Assemble paper handling options 5 Place the duple x unit on top of any installed dra wers. If you are not using a caster base , place the duplex unit on a table or optional printer stand and go to “P ositioning the printer . ” 6 Make sure the dr awers and duple x unit lock together securely .
13 Assemble paper handling options 8 Complete steps a and b if y our configuration does not include a duple x unit. a Inser t the two shor t stabilizer posts (4) into the top of the stabilizer scre ws that were pre viously installed in the optional dra wer .
14 Assemble paper handling options Installing printer memory and netw ork options 1 Press the release latches to open the upper and lower front doors. 2 Press down on the side door latches and open the side door . Remo vi ng the shi eld 1 Loosen, but do not remo ve , the six screws on the shield.
Ins tallin g m em ory Ins talling a firm ware card Ins talling an op tion ca rd 1 Unpack the memory option. 2 Open both latches on the connector . 3 Push the memory card fir mly into the connector until it snaps into place. 1 Locate the holes on the system board near the option card connectors.
16 Assemble paper handling options 6 Inser t the two scre ws sav e d from the metal plate (or the e xtra screws shipped with the card). 7 Tighten the screws to secure the card. Re attac hing the sh ield and closing the doors 1 Align the three ke yholes on the shield with the screws.
17 Set up the printer Step 3: Set up the printer Remo ving the print car tridge pac kaging 1 Open the printer upper front door . 2 Pull the print car tridge up and out. 3 Remov e the tabs and packaging from the car tridge. 4 Reinser t the pr int car tridge into the pr inter .
Attaching decals 1 Attach the numbered decals to the recessed areas on the and o verlay optional dra wers and tra ys. 2 If English is not your pref erred language: a Locate the adhesiv e ov er la y packaged with y our pr inter . b P eel the backing off the o verla y .
Attaching the printer cables Network cable Printer power cord V erifying printer setup Note: If you see a message other than Ready on the displa y , ref er to the printer publications CD f or instructions on clear ing the message.
Pri nti ng a netw or k setup pag e Printing Quic k Reference inf ormation Configuring f or TCP/IP Assigni ng a pri nter IP address 1 Press Menu until y ou see Utilities Menu, and then press Select . 2 Press Menu until y ou see Pr int Net Setup , and then press Select to print the page.
V erify ing th e IP s etting s Note: On Windows computers, clic k Star t Programs Command prompt (or Accessories Command prompt if using Windows 2000). Attaching the scanner shelf 3 Press Menu until y ou see Std Net Setup (or Network 1 Setup or Network 2 Setup), and then press Select .
3 Remo v e the top cove r or any pre viously installed print media handling options from the printer . Y ou will not need the cov er when the scanner shelf is attached. Store the cov er , it will be needed if you remo ve the shelf . 4 Align and inser t the scanner shelf mounting brack ets into the slots on top of the printer .
23 Install the scanner Step 4: Install the scanner 1 Open the scanner bo x and then remov e all items from the box e xcept the scanner . 2 Make sure y ou hav e the follo wing items: 3 Place all items e xcept the scanner aside for later use . 4 Remov e the scanner from the bo x and place it on a flat, le vel surf ace.
Step 5: Install the f eed tra y and paper stop 1 Connect the paper e xtension to the feed tr a y . P aper e xtension F eed tra y 2 Attach the f eed tray to the automatic document f eeder .
3 Open the paper suppor t on the feed tr ay . 4 Attach the paper stop to the top cov er . Install the feed tray and paper stop 25.
Step 6: Attac h cables and po wer cor ds Attaching cab les to the printer Note: Germany: Use only the Ger man T AE type F adapter shipped with this product because it contains a billing tone filter . The adapter is designed only f or the F connector of the Ger man wall outlet.
27 Attach cables and power cords Attaching cab les to the scanner 1 Connect the scanner cab le to the scanner . 2 Connect the automatic document f eeder cable to the connector on the back of the scanner . 3 Connect the powe r adapter cord to the scanner .
Step 7: T urn on the scanner and printer P erforming a power up sequence On/off s witch 1 If y ou are using a pr int ser v er with a modem, plug the telephone f ax line cable into the phone line outlet. 2 If y ou disconnected the Ether net network cable from the print ser v er or wall outlet, reconnect it.
6 W ait f or the MFP to initialize. When the scanner comes on, there is a shor t wait cycle while the firmware is initialized. Please Set Date/Time is displa yed on the first line of the MFP control panel and “ Please Wait ... ” is displa yed on the second line.
Step 8: Chang e y our default cop y settings A number of cop y settings are av ailable f or customizing the MFP output to suit your needs . Some settings or values are displa yed only if a specific option is installed on your printer . The indicator light ne xt to the value on the control panel illuminates to indicate the current setting.
Using y our br owser Note: Many of these settings depend on the printer , options, and scanner combination y ou hav e. 1 T ype the IP address of the MFP in the URL field of your browser (f or e xample, http://192.168.236.24), and then press Enter . 2 Clic k Configuration .
Step 9: Set send and receive fax inf ormation Under standing FCC fax requirements Note: See “Electronic emission notices” on page 48 and “T elecomm unications notices” on page 48 f or more FCC inf or mation. Note: If you do not ha ve a TCP/IP environment, y ou must use the MFP control panel to set your basic f ax inf or mation.
P e r for mi n g ma nua l f ax setup Y ou can quickly change men u settings from the MFP control panel by pressing Menu and then selecting the menu f or the area you w ant to change. T o man ually enter the f ax setup information: 1 On the control panel, press Men u repeatedly until y ou see F ax Quick Setup , and then press Select .
P erforming bro wser f ax setup Note: Configuration is a task usually done by a network administrator . If you are prompted f or a passw ord during the follo wing instructions, see your network administrator f or help .
Using Mar kVisi on Professional to set fax inf orm atio n Note: Instructions for installing MarkVision Prof essional are in the CD booklet shipped with the drivers CD . Changing optional settings Sett ing up a fax transmissi on log Note: F or a complete list of f ax log options, ref er to the online inf or mation on the MFP CD .
Creat ing permanent f ax desti nations Note: Once per manent f ax destinations are created, they become accessib le on the MFP control panel. Press Fax/Scan mode repeatedly until SCAN → F a x appears in the control panel displa y . Press Menu to mo ve through the list.
Step 10: Set up netw ork scanning Note: The control panel will not displa y a Scan to ... menu item unless the men u item has been configured. P erf orming Scan to Netw ork General Setup Note: After y.
P erf orming Scan to E-mail General Setup Note: Y ou ma y want to use the network administrator’ s address as the def ault address. When an e-mail cannot be sent, notification is retur ned to this address. Creating permanent e-mail destinations Note: Bef ore you create a destination, check the list at the bottom of the W eb page.
Note: Y ou can rapidly find your e-mail recipient b y pressing # and entering the shor tcut number on the MFP control panel. Creating permanent FTP destinations Note: Bef ore you create a destination, check the list at the bottom of the W eb page. Mak e sure your recipient is not already listed.
Step 11: V erify MFP setup Making a test cop y Cop y mode is the default setting of the control panel. 1 Make sure the Ready message is displa yed. 2 Place your original document in the scanner . 3 Press Go/Send to send a cop y to your printer . Sending a test fax Send a one page test fax to someone and ask f or f eedback.
Step 12: Distrib ute MFP user instructions Finding user instructions Distrib uting user inf ormation Limiting MFP use MFP online documentation includes helpful instructions for making copies, sending f ax es, and scanning documents to e-mail, FTP destinations, or bac k to your computer .
Solve setup pr oblems Prob lem Solution Ready message not displa yed The control panel and the printer are not talking to each other , or the printer or scanner may be turned off. 1 T urn the pr inter off , and then back on. 2 T urn the pr inter and scanner off .
Maintain y our scanner Clearing a paper 1 Open the automatic document f eeder . jam 2 Carefully pull out the jammed paper . 3 Close the automatic document f eeder .
Cleaning the automatic document feeder F eed rollers The scanner par ts can become contaminated with ink, toner par ticles, or paper coatings. Clean the scanner f eed rollers if documents do not f eed smoothly or easily , or if se ver al documents f eed at one time.
45 Maintain your scanner Cleaning the document glass 1 Open the document cov er . 2 W et a clean, lint-free cloth or cotton sw ab with water . 3 Wipe the scanner glass and automatic document f eeder area by mo ving the cloth or sw ab from side to side.
Mo ving the If you need to transport the scanner , follo w these instr uctions to scanner relock the scanner: Wa r n i n g : F ailure to loc k the scan mechanism bef ore moving the unit can cause inter nal damage . 1 Raise the scanner high enough to mov e the s witch down to the lock ed position.
47 Maintain your scanner 3 Remov e the old automatic document feeder pad assemb ly by squeezing and pulling out the upper par t of the pad clamp. 4 Hold the upper par t of the new clamp , squeeze , and place it gently in the pad holder . 5 Close the automatic document f eeder .
Notices The f ollowing notices apply to machine type 4036-302. The f ollowing telecommunications notices apply to those machines in which the print ser ver is installed.
compliant. An FCC compliant telephone cord is provided with this equipment. Ref er to the setup documentation f or instr uctions about connecting the f ax telephone cable. If you e xperience problems with this equipment that you cannot resolv e, contact Le xmar k International, Inc.
This precaution ma y be par ticularly impor tant in rural areas. CA UTION: Users should not attempt to mak e such connections themselv es, b ut should contact the appropriate electr ic inspection authority , or electrician, as appropr iate. This equipment uses the f ollowing jacks: CA11A.
all analog lines. Contact customer suppor t f or ordering information. South Africa telecomm unications notice This modem must be used in conjunction with an approv ed surge protection device when connected to the PSTN.
.
Readers’ Comments — We’d Like to Hear from Y ou IBM Infoprint M22 MFP Option Setup Guide Publication No. S510-2633-00 Overall, how satisfied are you with the information in this book? V ery Sati.
Readers’ Comments — We’d Like to Hear from Y ou S510-2633-00 S510-2633-00 IBMR Cut or Fold Along Line Cut or Fold Along Line Fold and T ape Please do not staple Fold and T ape Fold and T ape Please do not staple Fold and T ape NO POST AGE NECESSARY IF MAILED IN THE UNITED ST A TES BUSINESS REPL Y MAIL FIRST -CLASS MAIL PERMIT NO.
.
IBMR Part Number: 75P51 12 Printed in U.S.A. S510-2633-00 (1P) P/N: 75P5112.
Ein wichtiger Punkt beim Kauf des Geräts IBM Infoprint M22 MFP (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie IBM Infoprint M22 MFP noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für IBM Infoprint M22 MFP - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von IBM Infoprint M22 MFP reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über IBM Infoprint M22 MFP erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon IBM Infoprint M22 MFP besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von IBM Infoprint M22 MFP verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit IBM Infoprint M22 MFP. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei IBM Infoprint M22 MFP gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
