Benutzeranleitung / Produktwartung 324RX-Series des Produzenten Husqvarna
Zur Seite of 36
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 324R X-SERIES Oper ator’ s manual (EP A) Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment HELMET A helmet should be worn if the trees being cleared are taller than 2 m. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection.
English – 5 SAFETY INSTR UCTIONS Cutting attachment guar d This guard is intended to pre vent loose objects from being thrown to wards the operator .
6 – English SAFETY INSTR UCTIONS Cutting equipment Saw b lades are intended for cutting fibrous types of wood. Grass b lades and grass cutters are intended f or cutting coarse grass . A trimmer head is intended for trimming grass . Locking n ut A locking n ut is used to secure some types of cutting attachment.
English – 7 SAFETY INSTR UCTIONS • See instructions under the heading Star t. Star t the machine and apply full throttle. Release the throttle and check that the cutting attachment stops and remains at a standstill. If the cutting attachment rotates with the throttle in the idle position then the carburettor idle setting m ust be check ed.
8 – English SAFETY INSTR UCTIONS 2 K eep the teeth of the blade correctly shar pened! F ollow our instructions and use the recommended file gauge. An incorrectly shar pened or damaged b lade increases the risk of accidents. 3 Maintain the correct blade setting! F ollow our instructions and use the recommended blade setting tool.
English – 9 SAFETY INSTR UCTIONS • Make sure that the b lade is well suppor ted when you file it. Use a 5.5 mm round file with a file holder . • The filing angle is 15 ° . File alter nate teeth to the right and those in between to the left.
10 – English SAFETY INSTR UCTIONS General safety precautions Starting • The complete clutch cov er and shaft must be fitted before the machine is star ted, otherwise the clutch can come loose and cause personal injur y . • Ne ver start the machine indoors.
English – 11 SAFETY INSTR UCTIONS • The transpor t guard must alw a ys be fitted to the cutting attachment when the machine is being transpor ted or in storage. General w orking instructions Basic safety rules 1 Look around you: - T o ensure that people, animals or other things cannot aff ect your control of the machine .
12 – English SAFETY INSTR UCTIONS Correct balance Let the cutting attachment rest lightly on the ground. If you use a saw b lade it should balance about 10 cm above the ground to pre vent contact with stones and the like . Adjust the position of the suppor t hook to balance the clearing saw correctly .
English – 13 SAFETY INSTR UCTIONS Grass clearing using a grass b lade • Grass b lades and grass cutters m ust not be used on woody stems. • A grass b lade is used for all types of tall or coarse grass .
14 – English SAFETY INSTR UCTIONS Cutting • The trimmer is ideal for cutting gr ass that is difficult to reach using a normal lawn mower . K eep the cord parallel to the ground when cutting. A void pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
English – 15 WHA T IS WHA T? What is what on the c learing saw? 1 Blade 2 Grease filler cap , be v el gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop s w.
16 – English ASSEMBL Y Fitting the handlebar • Remov e the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar , (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar .
English – 17 ASSEMBL Y Fitting a blade guar d, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CA UTION! Use the recommended blade guard. See the T echnical data section.
18 – English ASSEMBL Y arrow in the diagr am shows the area where y ou should operate the soc ket spanner when loosening or tightening the nut. Fitting a trimmer guar d and Superauto II 1" trimmer head • Fit the correct trimmer guard (A) for use with the trimmer head.
English – 19 ASSEMBL Y Adjusting the harness and c learing saw Standar d harness Quick release At the front is an easily accessible , quick release . Use this if the engine catches fire or in any other emergency situation that requires you to free y ourself from the machine and harness.
20 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a f our-stroke engine. Make sure that there is alwa ys sufficient oil in the oil tank. Gasoline • Use high-grade unleaded petrol of at least 86 octane . • If the machine is not used f or some time the fuel tank should be emptied and cleaned.
English – 21 ST AR TING AND ST OPPING Chec k bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole .
22 – English ST AR TING AND ST OPPING W arm engine Ignition: Set the stop s witch to the star t position. Choke: Put the choke in w orking position. Primer bulb: Press the primer bulb repeatedly until fuel begins to fill the bulb . The bulb need not be completely filled.
English – 23 MAINTENANCE Carb urettor Function • The carburettor go v erns the engine’s speed via the throttle control. Air and fuel are mixed in the carb urettor. The air/fuel mixture is adjustable . Correct adjustment is essential to get the best perf ormance from the machine.
24 – English MAINTENANCE If the machine is low on po wer , difficult to star t or runs poor ly at idle speed: alwa ys check the spark plug first bef ore taking any further action. If the spark plug is dir ty , clean it and check that the electrode gap is 0,6-0,7 mm.
English – 25 MAINTENANCE • See the cutting attachment packaging f or correct shar pening instructions. • Shar pen b lades and cutters using a single-cut flat file. • Shar pen all edges equally to maintain the balance of the blade . Sharpening the saw b lade • See the cutting attachment packaging f or correct shar pening instructions.
26 – English MAINTENANCE Maintenance schedule Below y ou will find some general maintenance instructions. Daily maintenance • Check the engine oil le vel and top up if necessary . • Check throttle trigger and throttle trigger lock out function.
English – 27 TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le v el is calculated as the time-weighted energy total f or noise pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max.
28 – English TECHNICAL D A T A 324Rx Appro ved accessories T ype Cutting attachment guar d, Art. no. Arbor shaft thread M10 Grass b lade/grass cutter Grass 255-4 (Ø 255 4 teeth) 503 93 42-02 Grass .
English – 29 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine .
1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
.
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
´®z+H9y¶5O¨ ´®z+H9y¶5O¨ T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
.
´®z+H9y¶5O¨ 2004-03-29 ´®z+H9y¶5O¨ 1140258-95.
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna 324RX-Series (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna 324RX-Series noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna 324RX-Series - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna 324RX-Series reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna 324RX-Series erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna 324RX-Series besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna 324RX-Series verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna 324RX-Series. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna 324RX-Series gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
