Benutzeranleitung / Produktwartung 43355 des Produzenten Hunter Fan
Zur Seite of 43
Owner’ s Manual Model 43355 PROGRAMMABLE THERMOST A T M AM 4 TEMP.
2 Introduction CONGRA TULA TIONS! Y our new Climate T echnology electronic thermostat will provide years of reliable service . By saving en- ergy , your thermostat will pay for itself during its first season of use .
3 T able of Contents Read T his Before Installing Thermostat 5 F eatures 7 What Y ou Need 8 Remove Old T hermostat 8 Wire Labeling 9 Mount W allplate and Thermostat 11 Connect Wires and Mount Thermost.
4 P ermanent Manual Override 26 V acation Override (Programmable Hold) 27 Home T oday 28 Energy Monitor 30 F ilter Monitor 31 Auto Recovery 32 SP AN Setting Mode 34 Backlighting 35 Low Battery Warning.
5 Read This Before Installing Thermostat IMPORT ANT 1 Read the entire installation section of this Owner’s Manual thoroughly before you begin to install or operate your Climate T echnology T her - mostat. INST ALLA TION 2 All installation is normally performed at your thermostat.
6 Read This Before Installing Thermostat (continued) POWER FAILURE 7 Whenever the main power is interrupted or fails , the battery power retains the programs and cur - rent time . AUTO RECOVERY 8 Y our thermostat is set from the factory to gradually recover the room temperature from an energy sav- ing program to your comfort program.
7 F eatures energy home today fan auto on system heat cool off r eset day/time prog day program filter hold /return.
8 INST ALLA TION What Y ou Need T his thermostat includes two #8 screws and two w all anchors for mounting. T o install your thermostat, you should have the following tools and materials . ■ Phillips and Slotted Screwdrivers ■ Hammer ■ Electric drill and 3/16" bit ■ T wo 1.
9 Wire Labeling ■ Each wire coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually mark ed with a code letter as shown in T able A on the next page . ■ Note that this thermostat has multiple function terminals that allow Single-Stage Heat Pump ca- pability .
10 INST ALLA TION T able A NO TE: Do not connect a “Common” wire (sometimes labeled “C”) to any terminal on this thermostat. Tape up the wire and do not use.
11 Mount W allplate and Thermostat ■ Remove the wallplate from your thermostat by pressing the release tab on the bottom of the thermostat. (See F igure 2.) ■ P osition w allplate on wall and pull existing wires through large opening. Then level for appearance .
12 INST ALLA TION Connect Wires and Mount Thermostat Cover to W all Plate ■ Match and connect the labeled wires to the appro- priate coded terminal screws on the wallplate . (See F igure 4, 5.) Ignore any wires which may be present, but which were not connected to the old thermostat.
13 Selector Switches In order for this Climate T echnology thermostat to control your system, the system type must be speci- fied by selector switches on the printed circuit board inside the thermostat. NO TE: When changing these features after instal- lation, move the HEAT / COOL selector switch to OFF before removing the thermostat from the wall.
14 PROGRAMMING Setting Time and Day ■ T he LCD will show this information when batteries are first installed, or after the Reset button is pressed. T he temperature will update after a few seconds . ■ During time and day setting mode , the temperature and program displays will go blank.
STEP 3: ■ Press again to change from minute setting to day setting. The current day will be flashing. ■ Press to change the Day up or down to the current day . STEP 4: ■ Press again to change back to the normal display . NO TE: You may press hold /return at any time during Day and Time setting to return to the normal display.
16 PROGRAMMING Setting Time and Day (continued) 12 HR. / 24 HR. TIME FORMA T Y our thermostat is set from the factory in normal 12 (AM / PM) time format. T o change to 24 hour (military) time, press program at any time while the Hour , Minute , or Day is flashing to toggle between the 12 hour and 24 hour formats.
17 Personal Program Schedule Before programming or changing programs , use this P ersonal Program Schedule to determine which times and temperature settings will best satisfy both your comfort and energy saving requirements . Use a pencil so you can revise your records each time you change your temperature settings .
18 PROGRAMMING Manual Programming ■ Y our thermostat can be programmed for week- days and week ends, or have unique programs for all 7 days. Use W eekday/Week end Programming below or 7-day Programming on page 21 to enter or revise programs to match your Personal Pro- gram Schedule .
(continued) W eekday/Weekend Pr ogramming ■ Slide System Selector Switch to HEA T or COOL to program the corresponding system. NO TE: If the system selector is in the OFF position, no programming is permitted. The LCD display will show only dashes when the program key is pressed.
20 PROGRAMMING W eekday/Weekend Pr ogramming (continued) STEP 4: ■ Press again to change to the program temperature . T he current temperature will be flashing. ■ Press to change the temperature . STEP 5: ■ Press again to move to the next program number .
7-Day Programming ■ Slide System Selector Switch to HEA T or COOL to program the corresponding system. STEP 1 ■ Press to enter program mode , display shows week- day programs . ■ Press 2 times to reach the Monday program. Step 2 ■ Use , and program keys to set the 4 programs for Monday .
22 PROGRAMMING Reviewing Programs Y ou may want to review the programs to confirm that the settings are compatible with your lifestyle . ■ Press to display M – F programs . ■ Press repeatedly to cycle through the 4 programs . ■ Press to display the Sa – Su programs .
■ Press again to change to Monday’ s program. ■ Continue pressing to cycle through each day . ■ Press repeatedly to cycle through the 4 programs . ■ Press to return to normal mode . ■ After 15 seconds , the thermostat will return to nor - mal mode automatically .
24 OPERA TION System Selector Switch T he System Selector switch on the front of the thermostat determines the operating mode of the thermostat. Y ou may select COOL, OFF , HEA T . NO TE: Anytime you install or remove the thermostat from the wallplate, slide the System Selector to the OFF position to prevent the possibilitu50.
25 T emporary Manual Override To temporarily change the current set temperature without affecting your progr am: ■ Press and hold for about 1 second to enter Manual Override mode . When display flashes , you can release the k ey . ■ Press again to change to your desired Set T empera- ture .
26 OPERA TION Permanent Manual Override To hold your Manual Override for vacation or just an extended period of time: ■ Press to mak e the current program temperature the HOLD temperature. HOLD will be displayed on the LCD , and the Program number will disappear .
V acation Override (Pr ogrammable Hold) T his thermostat can hold a fixed temperature for a selected number of days (up to 30). After the selected number of days, the thermostat will return to normal program operation. This feature allows you to return home to your normal comfort setpoint temperatures .
28 OPERA TION Home T oday T his Climate T echnology patented feature allows you to quickly and temporarily override your energy saving program setting on days when you are normally away from home with one k ey press. ■ Press to enter the Home T oday override.
■ If the system is changed between Heat and Cool modes during the “Home T oday” override period, the setpoint temperature will be automatically updated. It will auto- matically change from the highest heat program setpoint to the lowest cool program setpoint, or from the lowest cool program setpoint to the highest heat program setpoint.
30 OPERA TION Energy Monitor energy Usage Hr Min T oday energy T he Energy monitor feature measures and stores the amount of time the heating and air conditioning sys- tem operates. Usage can be displayed for T oday (since 12am), Y esterday , This Week (since Monday), Last W eek (last Monday through Sunday), and T otal (up to 999 Hrs.
31 Filter Monitor Y our thermostat also keeps a record of the number of hours your filter has been in use . T o maximize your system’ s performance and energy efficiency , change or clean your filter regularly .
32 OPERA TION F or example , in Heat mode , you could have the follow- ing programs: Program #4 (Overnight) Program #1 (Morning) Set T emp = 60 ° F Set T emp = 68 ° F T ime = 10pm T ime = 6am T he room temperature fell to 60 ° F overnight.
33 Details of Auto Recovery Operation: ■ Auto Recovery can be disabled by sliding the Re- covery switch on the circuit board to the DISABLE position. Refer to page 13. ■ Auto Recovery will not operate if Permanent hold, T emporary hold or Home T oday is in operation.
34 OPERA TION SP AN Setting Mode Y our thermostat is set at the factory to cycle at 1˚F (0.5˚C) above and below the set temperature . (Span = 2) T his setting has been designed to pro- vide a comfortable room temperature under most all conditions .
35 Backlighting (INDIGLO ® night-light) Y our thermostat has an electroluminescent lamp that backlights the display for easy viewing in the dark. When any k ey is pressed or the System Switch is changed, the display is illuminated. T he display will remain illuminated for 5 seconds after the last k ey is pressed.
36 SAFETY FEA TURES Low Battery W arning ■ Y our thermostat has a two-stage low battery warning system. When the batteries are first detected to be weak, the first stage low battery warning is indicated by battery symbol flashing on the LCD display .
37 Error Mode ■ If the thermostat is unable to control your system due to an unex- pected battery problem, the thermostat will enter Error Mode . In this condition, the thermostat flashes “Err” on the LCD display , and shuts off your system.
38 TROUBLESHOOTING Scrambled or Double Display (numbers over numbers) No Display Entire Display Dims Program Does Not Change at your Desired Setting Auto / F an Does Not turn On Heating or Cooling Does Not Go On or Off Solution 1. Remove clear mylar sticker .
39 Problem (cont.) Solution (cont.) Erratic Display If unit continues to operate in the Off position Thermostat permanently reads “HI, ” “LO , ” or “ERR-” after pressing reset button 1. Press the RESET button once with a small pin and hold for two seconds.
40 WIRING DIAGRAMS 4-wire Heat/Cool System 5-wire Heat/Cool System Jumper Wallplate T erminals Fan Relay Cool Contactor Heat Relay or V alve 24V Supply Heat/Cool Rh Rc Y/O W/B Y1 G X X System Selector.
41 Single-stage Heat Pump 2-wire Heat Only Jumper X OR Heat Mode Cool Mode Connect to Proper Reversing V alve T erminal. See T able A System Selector STD HP – Wallplate T erminals Rh Y/ O W/ B Rc G .
42 WIRING DIAGRAMS 3-wire Heat Only Jumper X X Wallplate T erminals Fan Relay Rh Rc Y/O W/B Y1 G Heat 24V Supply X Heat Relay or V alve System Selector STD HP – 3-wire Cool Only Rh Rc Y/O W/B Y1 G J.
© 2003, Climate T echnology Corp F orm No . 41645-01, 8/03 Climate T echnology Corp. 2500 FRISCO A VENUE MEMPHIS , TN 38114 A Hunter Fan company.
Ein wichtiger Punkt beim Kauf des Geräts Hunter Fan 43355 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hunter Fan 43355 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hunter Fan 43355 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hunter Fan 43355 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hunter Fan 43355 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hunter Fan 43355 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hunter Fan 43355 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hunter Fan 43355. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hunter Fan 43355 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
