Benutzeranleitung / Produktwartung TCR ID-10 des Produzenten Humminbird
Zur Seite of 19
.
TRANSDUCER MOUNTING PROCEDURE Humminbird’s high - speed transducer is supplied with your LCR. This transducer has been designed to give good high speed readings on most all boat designs, including aluminum. Please carefully consider the f ollowing before installing your transducer.
by rotating up out of the metal spring bracket without harming the transducer, or your boat. The transducer can be re - engaged by simply rotating the transducer down and snapping it back in place.
Once the location is determined mark and drill three 7/64” dia.. holes noted on the template. Attach the metal bracket using three #10 self threading screws supplied. Be sure to align holes in the center of the Bracket slots. On some alu minum boats it may be necessary to use a wood back - up plate.
NOTE: On boats with more than 15 degree deadrise angle it may be necessary to mount the transducer slightly off parallel with the water level. (See Figure E) Mark and drill the three 9/64” dia. holes as shown on the template. Attach the metal bracket using the three #10 self threading screws supplied.
Step 4 TRANSDUCER ASSEMBLY - Insert the transducer assembly into the metal bracket from the bottom. Push up until the holes in the plastic pivot align with the uppermost holes in the bracket. Slide the O - ring on to the headed pin and in sert it through the two parts.
wrench provided. The screws are visible through the access holes on each side of the metal bracket. Check to make sure the transducer main body is rigidly fastened to the pivot . (See Figure H) Step 6 CHECK POSITION OF TRANSDUCER - At this point, check to see that the bottom of the transducer is a minimum of ¼” below the bottom of the transom.
7. Remove the water and transducer and clean the marked area and t he bottom of the transducer thoroughly. 8. Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted.
Install the mounting knobs and tighten snugly. The unit can now be swiveled and tilted to any desired position..
OTHER MOUNTING OPTIONS 1. The LCR gimbal bracket can also be mounted on the SM - 4, quick disconnect swivel mount. 2. The LCR gimbal bracket can also be mounted directly to the dash without the swivel mount, however, this method is not recommend ed since the unit cannot be rotated.
It plugs into the outlet on the back of the unit marked “Power”. The transducer connector is identified with the letter T and plugs into the outlet on the back of the unit marked “Transducer”.
.
Specifications: Operating Frequency 200 KHz Power Requirement 12 volts Power Cable Length 111/2' Transducer (standard) XHS-6-16 high-speed Transducer Cone Angle 16 degrees Transducer Cable Length.
NOTE: The built - in simulator will allow y ou to practice adjusting the sensitivity, but your adjustments will not change readings being displayed on the screen. READING THE TCR ID - 10 SCREEN Your TCR has a liquid crystal display, or LCD. The liquid crystal material in the display aligns itself to either block light or let light pass through.
60' scale and it changes to the 0 - 30' scale, the entir e screen will look as if you had been in the 0 - 30' range all along. 2. Using zoom and bottom - lock. Through Pixel Memory Capacity, the memory in the TCR ID - 10 stores readings in much finer detail than is displayed in the "regular mode.
Of course, the best way t o learn to read your TCR ID - 10 is to use it, especially in familiar locations. If you know what's underwater and can see it displayed on the screen, then you're on your way to being an experienced TCR user.
OPERATING THE TCR ID - 10 Your new TCR ID - 10 offers unique automatic features, as well as many adjustable ones. If you're learning to operate the TCR ID - 10 with its simulator, follow the directions listed at "Built - In Simulator" on page 16, and then come back to this page.
The following describes the functions and how to use them, in order of appearance after you turn the unit on. 1. Sensitivity Automatic setting: on, "O" or normal As conditions change, the computer will automatically increase or decrease the sensitivity setting.
buttons, you can move the zoom window while the zoom is activated, without having to press Select again. 5. Bottom - Lock Automatic setting: off You can easily turn on the bottom - lock with the On/Off button. When on, this function shows up - close zoom r eadings in reference to the bottom.
Ein wichtiger Punkt beim Kauf des Geräts Humminbird TCR ID-10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Humminbird TCR ID-10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Humminbird TCR ID-10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Humminbird TCR ID-10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Humminbird TCR ID-10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Humminbird TCR ID-10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Humminbird TCR ID-10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Humminbird TCR ID-10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Humminbird TCR ID-10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
