Benutzeranleitung / Produktwartung Z200 des Produzenten HP
Zur Seite of 199
HP Z200 Small Form Factor Workstation Maintenance and Service Guide.
Copyright Information © Copyright 2010 Hewlett-Packard Development Company, L.P. Warranty Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
About this guide This guide provide s service and m aintenance information for th e HP Z200 Small Form Factor (SFF) Workstation. It includes these topics: Guide topics Product overview on page 1 Setti.
iv About this guide ENWW.
Table of contents 1 Product overview .. ......... ............ ........ ......... ............ ........ ............ ......... ......... ........... ...... .......... ......... .......... .... 1 Product features ............. ......... .......... ....
Installing with the HP driver CD ...... ............. ............................ ........... ........................ ....... 18 Installing and customizin g Red Hat-enabled computers ....... ............. .......... .............. ........ 19 Verifying hardwar e compatibility .
System S oftware Manage r ........... ............................... .................... ................................. . 45 Proac tive Change Noti ficati on ........................ ...................................... ........................
Tools and softwar e requirements ...................................... ............................................ .... 64 Special handling of components ......... .......... ........... ......... .......... ......... ........... ......... .........
Installing the front panel I/O device assembly ........ ........ ............ ........... ........... . 98 Speaker ....................... .......................... ....................... .............. ...................... ........... .... 100 Removi ng the speake r .
Diagno sis guidelines .................... ......................... ......................... ......................... ........... ... ........... 128 Diagnos is at startup .................. ................. ........... ................. .........
7 Confi guring RAID devi ces ...... ............. ....................... ......................... ............. ................... ..................... .. 162 Maximum ha rd drive co nfigurations .... .................................... ..........
xii ENWW.
1 Product overview This chapter presents an overview of the hardware components of the computer. It includes these to pics: Topics Product features on page 1 Computer specifications on page 7 Product .
The following figure sh ows the typical system board block dia gram. Figure 1-1 System board block diagr am NOTE: The x1 and x16 designators describe the mech anical len gth of the slot. The number in parentheses lists the number of elec trical PCIe lanes routed to the expansion slot.
Expansion car d slots The computer provides multiple graphics and I/O slot s: on e full PCIe Gen2 x16, one PCIe x16(4); one PCIe x1; and one PCI 3 2/33. These slots provid e extra I/O bandwidth for high speed I/O cards. NOTE: The total o f all graphics cards cannot exceed 45 W, and the total I/O power u sage cannot exceed 80W.
Computer components This section describes the computer components, includ ing front and rear panel components. For complete and current informa t ion on supported accessories and comp onents for the computer, see http://partsurfer.hp. com . Chassis componen ts The following image shows the compon ents of a typica l computer layout.
Front panel components The following figu re shows the layout of a typical front panel. Figure 1 -3 Front panel Table 1-2 Front panel co nnector s Item Symbol Description Item Symbol Description 1 Opt.
Rear panel components The following fig ure shows the layout of a typical re ar panel. Figure 1-4 Re ar panel NOTE: The labels for the rear pan el connectors use industry-standard icons and colo rs.
Computer specifications This section provid es compute r chassis, power su pply, and en vironmental specif ications. Physical characteristics The following table lists the comput er physical characteristics. Weight (Typical configuration) 7 .6 kg (16.
Power supply currents Table 1- 5 Maximum current pe r rail Output (240W) +12V Main +12Vcpu –12V 12Vsb Nominal output voltage 12.1 12.1 -12.0 11.4 Maximum continuous current 14A 12A 0.15A 1.3A 240W combined CAUTION: Do not exceed 240 watts of total continuous output power.
Power supply specifications Table 1-6 Power su pply specifications Item Description Power supply 240W Wide Ranging, Active PFC and 89% efficient Operating voltage range 90 – 264 VAC Rated voltage ra.
System fans This computer includes: ● One front system fan ● One power supp ly fan In addition, some graphics cards include onboard fans. Resetting the power supply If an overload tri ggers the power supply overlo ad protection, power is immediately disconne cted.
Environmental specifications The following tab le lists the environmental specifications of HP Workstations. Table 1-7 HP Workstation en vironmental sp ecificatio ns Temperature Operating : 5 to 35°C (40 to 95°F) Non-operating : -40 to 60°C ( -40 to 140°F) NOTE: Derate by one degree C (1.
ENERGY STAR Qualification HP computers marked with the ENERGY STAR logo are compliant with the ap plicable U.S. Environmental Protection Agency (EPA) ENERGY STAR specificat ions for computers. The EPA ENERGY STAR logo does not imply endorsement by the EPA.
ERP compliance mode This computer provides ER P comp liance mode capability. When enabled, t his feature enable s the computer to shu t down to the low est possible pow er state by removing all power to the system board. When disabled, th e computer po wers down co nventionally.
Intel Turbo Boost Technology The HP Z Workstation series supports Intel® Turbo Boost Technolog y . This feature enables the CPU to run at a hig her than normal rate. When all CPU cores are not necessary for the workload, inactive cores are turned off and power is diverted to the active cores to increase their performance.
Ensuring proper ventilation Proper ventilation for the system is important for computer operation. Follow these guidelines to ensure adequate ve ntilation: ● Operate the computer on a stu rdy, level surface. ● Place the computer in an area with ad equate ventila tion.
2 Setting up the operating system This chapter provides setup and update inf ormation for the comput er operatin g system. It includes these topics: Topics Setting up the Microsoft operating system on.
Setting up the Microsoft operating system NOTE: If you ordered a downgrade from Windows Vist a or Windows 7 to the Windows XP Professional operating system, your system comes pre-installed with the Windows XP Professional operating system. This configuration comes with re covery media for the Windows Vist a or Windows 7 operat ing system only.
Setting up Red Hat Enterprise Linux HP offer s an HP Installer K it for Linux (HPIKL) to su pplement Red Hat box sets and he lp HP Linux customers customize their system image.
Installing and customizing Red Hat-enabled computers Linux-enabled computers require the HP Installe r Ki t and the purchase o f a Red Hat Enterp rise Linux box set.
Determining current BIOS To determine the current BIOS of the computer during system power up: 1. Wait for F10=setup to appear o n the lower right corner of the scre en. 2. Press F10 to enter the F10 Se tup utility. The F10 Setup utility displays the computer BIOS version under File > System Information .
Upgrading BIOS To find and downlo ad the latest available BI OS, which includes the latest enha ncements: 1. Go to http://www.hp.com/ go/workstationsupport . 2. Select Download D rivers an d Softwar e from the left menu column under Tasks. 3. Follow the instructions to locate the latest BIOS available for the comp uter.
3 Restoring the operating system This chapter descr ibes how to r estore the Windo ws or Linux operat ing system. It includes these topic s: Topics Restore methods on page 22 Ordering backup software .
Ordering backup software If you cannot create system recovery CDs or DVDs , you can order a recovery disk se t from the HP support center. To obtain the sup port cent er telephone number for yo ur region see http://www.
Restoring Windows XP Professional This section describes how to restore th e W indows XP Professional operating system. NOTE: The computer must have a CD or DVD wr iter instal led to create the media set. Creating RestorePlus! media The RestoreP lus! kit can be created using the files contained on the hard driv e.
Creating HP Backup and Recovery (HPBR) media NOTE: HPBR is only supported on Windows XP systems. For details, refer to the documentation on the Supplemental So ftware - HP Backup and Recovery CD included with the computer. The documentation can be accessed during installation.
Restoring the operating system CAUTION: Before you restore the operat ing system, back up your data. When you run RestorePlus! from m edia, the process deletes all information on the primary hard drive, including all partitio ns. If you run R estorePlus! fro m the recovery partition, onl y the root (C:) partition is affected .
NOTE: Make copies of th e ISO recovery images on CD as backup files in case your computer experiences a hard drive failu re. ENWW Restoring Novell SLED 27.
4 System management This section describes the tools and utilities th at provide system managem ent for the computer. It includes these topics: Topics BIOS ROM on page 29 The Com puter S etup (F1 0) U.
BIOS ROM The BIOS ROM is a collection of machine langu age ap plications stored as firmware in ROM. It includes functions such as Power on Self Test (POST), PCI de vice initialization, Plug and Pl ay support, power management, and the Computer Setup (F10) Utility.
selected. To manu ally switch to POST Mess ages Enabled du ring POST, pres s any key except F1 through F12 . ● Specify an Ownership Tag, which appears when the computer is pow ered on or restarted. ● Specify the Asset Tag or prope rty identification number assigned by the company to this co mputer.
Accessing the Computer Setup (F10) Utility To access the Computer Setup (F10) Utility menu: 1. Power on or restart the computer. 2. When the displa y is active and F10=Setup appears in the lo wer right corner of the screen, press F10 . If you do not press F10 at the appropriate time , try again.
The Computer Setup (F10) Utility menu The following table describes t he functions availabl e in the Computer Setup (F10) utility menu. NOTE: With new BIOS rele ases, the following content is su bject to change, so the men u might be different than shown.
Heading Option Description Ignore Changes and Exit Exits computer setup without applying or saving changes. Save Changes and Exit Saves changes to system configuration and exits the computer se tup.
Heading Option Description Boot Order Ena bles you to configure the bo ot, diskette drive, and hard disk drive orders by physically reordering the menu entries.
Heading Option Description Device Security Makes the following devices avail able or hidd en to the computer: ● Serial Port ● Front USB Ports ● Rear USB Ports ● Internal USB Ports ● System Audio ● IEEE 1394 Controller (Not available on some models.
Heading Option Description System Security Provides these options: ● Data Execution Prevention—Enables or disabl es Da ta Execution Prevention mode in the CPUs. This mode prohibits code from running in pages that w ere set up as data pa ges, and prevents attacks such as buffer overflows.
Heading Option Description Hardware Power Management Enables or disables: ● SATA Power Management ● Intel Turbo Boost Techn ology ● Enhanced Intel Turbo Boost Technology ● ERP Compliance Mode Thermal Enables you to set the rate of the system fan when the CPU is in idle.
Heading Option Description Chipset/ Memory Enable/disable these optio ns: ● PCI SERR# Generation (Enable or Disa ble)—Cont rols PCI SERR# generation for ill-behaved PCI add-in cards (that can generate SERR# spuriously). ● PCI VGA Palette Snooping (Enable or Dis able)—C ontrols PCI VGA Palette Snooping for compatibility purposes.
Desktop management This section summarizes capab ilities, features, and key components of computer management, including: Topics Initial computer configuration and deployment on page 40 Installing a r.
Initial computer confi guration and deployment The computer includes a preinsta lled system softw are image. After a brief software unbundling process, the computer is ready to use.
Replicating the setup This section provides information ab out replicating the computer setup. Copying a setup configuration to a single compu ter CAUTION: A setup configuration is model- specific. File system corruptio n can result if source and target computers are not the same model.
Copying a setup configu ration to multiple computers CAUTION: A setup configur ation is model-spec ific. If source and ta rget computers ar e not the sa me model, file system corrupti on can result. For example, do not co py the setup configuration from an HP xw8600 Workstation to a n HP Z200 Workstation.
Updating and managing software HP provides several to ols for managing and up dating software on desktops and computer s: ● HP Client Manager Software ● System Software Manager ● Altiris Client .
HP SoftPaq Download Manager HP SoftPaq Downloa d Manager is a free, easy-to -use interface for locating and downloa ding software updates for the H P client PC models in your e nviro nment. By specifying your models, op erating system, and language, you can qu ickly locate, sort, and select th e softpaqs you need.
System Software Manager System Software Manager (SSM) is a utility avail abl e on Windows computers that en ables you to update system-level software on multiple systems simultaneou sly.
ROM Flash HP computers incl ude a programmable flash ROM. By establishing a setup password in the Computer Setup (F10) Utility, you can protect the ROM from being inadvertently upda ted or overwritten. This function is importa n t to ensure the ope rating integrity of the computer.
FailSafe Boot Block ROM The FailSafe Boot Block ROM enables system recove ry in the unlikely event of a ROM flash failure . For example, if a power failu re occurs during a ROM upgr ade, the Boot Block uses a flash-protected section of the ROM to verify a valid system ROM flas h when power is restored to the computer.
Workstation security This section provides informatio n about providing system security through asset tracking, password security, hard disk drive locking, and chassis locks.
Feature Purpose How it is established Setup Password Prevents reconfiguration of the computer (use of the Setup utility) until the password is entered From the Computer Setup (F10) Utility menu Networ.
DriveLock applications The most practical use of DriveLock is in a corp or ate environment. The system administrator would be responsible for configuring the hard disk drive, wh ich involves setting the DriveLock master password and a temporary user p assword.
Enabling DriveLock To enable and set the DriveLock user password: 1. Power on or restart the computer. 2. As soon as the comput er is powered on, press and hold F10 until you enter the Com puter Setup (F10) Utility. Press Enter to bypass the title scr een, if nec essary.
Password security The power-on password prevents un authorized use of the computer by requiring entry of a password to access applications or da ta when the computer is powered on or restarted.
Establishing a power-on password us ing computer setup Establishing a powe r-on password through the Computer Setu p (F10) Utility prevents access to the computer when power is connect e d, unless you specify th e password. When a power-on password is set, the Computer Setup (F10) Utilit y presents Password Options in the Security menu.
Entering a se tup password If a setup password h a s been established o n the comp uter, you will be prompted to enter it ea ch time you run the Comput er Setup (F10) Ut ility. To enter a setu p password: 1. Restart the c omputer. 2. As soon as the computer is p owered on, press and hold F10 until you enter the Computer Setup (F10) Utility.
Deleting a power-on or setup password To delete a power-on or setup password: 1. Power on or restart the computer. 2. Choose from the followi ng: ● To delete the p o wer-on password, go to step 4. ● To delete the setup pa ssword, as soon as the computer is powere d on, press and hold F10 until you enter the Computer Setup (F 10) Utility.
Clearing passw ords If you forget the password, you cannot access the c omputer. For instructions about cl earing passwords, see Config uring password security and r esetting CMOS .
Cable lock (optional) To prevent theft, the re ar chassis pa nel of the co mputer accommodates a keyed cable lock. This cable lock attaches to the chassis a nd secures it to the work area.
Dual-state power button With ACPI enabl ed, the po wer button can function as an on/off switch or as a button. This feature do es not completely turn of f power, but inst ead causes th e computer to enter a low-powe r standby state.
5 Replacing components This chapter prese nts removal and installation p rocedures fo r most internal compu ter components . It includes these topics: Topics Warnings and cautio ns on page 60 Service .
Warnings and cautions WARNING! Any surfac e or area of the equi pment mark ed with this symbol indicates the presence of a hot surface or hot compo nent. If this surface is contacted, the potent ial for injury exists. To reduce the risk of injury from a hot compo nent, enable the surface to cool befo r e touching.
Service considerations Review the following service considerations before replacing system components. Cautions, warnings and safety precautions Review the cautions, warnings, and safety preca u tions before accessing the computer compon ents. Also, r eview the Safety and Regulatory Guide that ca me with the computer for more information .
Preventing ESD equipment damage Many electronic components a r e sensitive to ESD. Ci rcuitry design and structure determine the degree of sensitivity.
Grounding the work area To prevent stat ic damage in the work area: ● Cover the work surface with approved static-dis si pative material. Use a wrist strap connected to the work surface, and properly grounde d tools and equipment. ● Use static-dissipative mats, foot straps, or air ionizers to give added protection.
Tools and software requirements The tools nece s sary for computer comp onent removal and insta llation are: ● Torx T-15 driver ● Flat blade and cross-tip screwdrivers ● Diagnostics software Special handling of components The components incl uded in this section require special handling wh en servicing the computer.
Hard drives Hard drives are frag ile, precision compon ents. Avoid sub jecting them to physical shock an d vibration. The following g uidelines apply to all drives, incl udi ng failed drives, replacement drives, and spares. ● Do not remove hard drives from th e shipping package for storage.
Removing and installing components Component locations The following i llustration and table iden tify computer system b oard components. Figure 5-1 System board component lo cations Table 5- 2 System.
For related system architecture information, see System board architecture on page 1 . ENWW Removing and installing components 67.
Predisassembly procedures CAUTION: To avoid person al injury, equipment dama ge, or data loss, read the sections on Warnings and cautions and the Safety and Regulatory Information fo r the computer before servicing comp onents. Perform the fol lowing steps before servicing a computer: 1.
Disassembly order For convenien ce, disassembly proced ures should be fo llowed in a particular or der. Use t he following table to determi ne the sequence in which to acce ss major computer components. Table 5-3 compu ter component insta llation To install/ replace.
Unlock it and pull it out of the cable lock slot as shown in the fo llowing figure. Figure 5-2 Removing the cable lock 70 Chapter 5 Replacin g components ENWW.
Access panel Before accessing th e internal componen ts of th e computer, you must remove the access p anel. This section describes how to remo ve and install the ac cess panel. Removing the access panel WARNING! Power off the computer and discon n ect the power cord from the electri c al outlet before you remove the computer access panel.
Bezel This section describes how to remove and install the front ch assis bezel. Removing the front bezel To remove the fron t bezel: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 . CAUTION : Failure to follow the predisassembly pro c edures can result in equipmen t damage or data loss.
Front bezel security You can lock the front bezel in place by installing a security screw prov ided by HP. To install the security screw: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 . CAUTION: Failure to follow the pred isassembly proce dures can result in equipment da mage or data loss.
6. Install the security screw ne xt to the middle front bezel release tab to se cure the front bezel in place. Figure 5-6 Installing the Front Bezel Security Screw 7. Replace the access pa nel. 8. Reconnect all connection s and equipment listed in the Predisassembly procedures on page 68 .
3. Disconnect the sensor cable from the in -line chassis cable as shown below (1). Figure 5-7 Removing the access pa nel sensor 4. Slide the sensor back in its slo t, push the sensor down, and then re move it from the chas sis (2). Installing the access panel sensor To replace the acce ss panel sens or, reverse th e previous steps.
Access panel solenoid lock The access panel so lenoid lock provides a method to lock the acce ss panel by means of a local or remote signal-controlle d solenoid. This section describes how to remove a nd install the access panel solenoid lock. Removing the access panel solenoid lock To remove the access panel solenoid lock: 1.
NOTE: For information about con f iguring SATA RAID devices, see Configuring RAID devices on page 162 . Predisassembly for drives Take these actions before you begin installing or re moving a drive: Follow all general pred isassembly procedur es Prepare the computer for servicing b y following the Predisassembly proced ures on page 68 .
Remove bezel blanks On some models, you may need to remo ve the bezel bl an ks that cover the 3.5- inch and 5.25-inch d rive bays before you install a drive. T o remove a bezel blank: 1. Remove the access panel (see Removing the access panel on page 71 ).
Table 5-5 System Bo ard Drive Connections No. System Boa rd Connector System Board Label Color 1 SATA0 SATA0 dark blue 2 SATA1 SATA1 black 3 SATA2 SATA2 black 4 eSATA eSATA black 5 Media Card Reader M.
Table 5- 6 Extra Guid e Screw Lo cations No. Guide s crew, color Device 1 Black M3 Metric Screws Optical disk drives, SSDs, small form factor hard drives (6.3cm/2.5in), media card reader 2 Silver 6-32 Standard Screws 8.9cm/3.5in hard disk drives, front bezel security There are at total of five extra silver 6- 32 standard screws.
4. Rotate the drive cage to its upright position. Figure 5-11 Rotat ing the Drive Cage Up 5. Disconnect the power cable (1) and data cabl e (2) from the rear of the optical drive. Figure 5-12 Disco nnecting the power and data ca bles 6. Rotate the drive cage back down to its normal position.
7. Press down on the gre en drive retainer button loca ted on the left side of the drive to disengage the drive from the dr ive cage (1). While pressing the d r ive retainer button, slide the drive back until it stops, then lift it up and ou t of the drive cage (2).
5. Install fou r M3 metric gu ide screws in the lo wer holes on each side of the drive. Either re-u se the screws used by your previous optical drive or use the extra HP—provided guid e screws mounted on the front of th e chassis. (See Locate extra guide screws on page 79 .
7. Rotate the drive ca ge to its upright position. Figure 5-16 Rotating the Drive Cage Up 8. If a cable is not alread y present and connected: a. Connect the SATA data ca ble to the system board connector labeled SATA1. b. Route the data cabl e through the cable guides.
10. Connect the power cable (1) and data cable (2) to the rear of the opti cal drive. Figure 5-18 Connectin g the power and data cables 11. Ca refully rotate the drive cage ba ck down to its n ormal posit ion. CAUTION: Be careful not to pi nch any cables or w ires when rotat ing the driv e cage down.
5. Disconnect the drive cables from the rea r of the dr ive, or, if you are removing a med ia card reader, disconnect the USB and 1394 cables from th e system board as indicated in the following illustrations.
6. Press down on the green drive retainer button locate d on the left side of th e drive t o disengage the drive from the drive cage (1) . While pressing the drive retainer button , slide the drive back until it stops, then lift it up and out of the drive cage (2) .
5. Place the drive's guide screws into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it locks i nto place. TIP: Angle the drive toward one side of the chassi s to line up the guide screws with the slots.
4. Rotate the drive cage to its upright position. Figure 5-23 Rotat ing the Drive Cage Up 5. Rotate the power supply to its upright positio n. Th e hard drive is located beneath the powe r supply.
6. Disconnect the p ower cable (1) and data cab le (2) from the hard drive. Figure 5-25 Removi ng the optical drive 7. Press down on th e green release latch n ext to th e hard drive (1). While holding the la tch down, slide the drive forward until it stops, then lift th e drive up and out of the bay (2).
8. To install a new hard drive , the silver and blue isolation mountin g guide screws from the old hard drive to the new hard drive . Figure 5-27 Installing the hard drive guide screws You can also install a small form factor (6.4 cm /2.5 in.) hard drive in the primary drive bay: a.
9. Align the guide screws with the slots on the chassis drive cage, pr ess the hard d rive down into the bay, then slide it back unt il it stops and locks in place.
10. Connect the drive cables: a. Connect the power ca ble (1) and data cable (2) to the hard drive . Figure 5-30 Removing the optical drive b. Route the SATA and power cables throu gh the cable guide on the bottom of th e chassis frame behind the h ard drive.
● Do not bend a ny cable sharply. A shar p bend can break the in ternal wires. ● Never bend a SATA da ta cable tighter t han a 30 mm (1.18 in) ra dius. ● Never crease a SATA data cable. ● Do not rely on components like t he drive cage, power supply, or co mputer cover to push cables down into the ch assis.
Item Description Item Description P3 CPU po wer P7 SATA PWR1 (P16 0 on system board) for optical disk or hard disk drives P4 Hard disk drive Using the Small Form Factor Com puter in a Tower Orientation The Small Form Fa ctor computer can be used in a tower o rientation.
Front panel I/O device assembly This section describes how to remove and install a f ront panel I/ O device assemb ly. Removing the front panel I/O device assembly To remov e the fr ont pane l I/O device assembly: 1. Disconnect power from the computer (see Predisassembly proced ures on page 68 ).
6. Disconnec t the front pane l I/O device assembly cables from the system board as shown below. Figure 5-34 Disco nnecting the front panel I/O cabl es 7. Carefully guide the cables through the ch assis op enings (1), as shown in the following figure .
Installing the front panel I/O device assembly To install the front panel I/O device assemb ly: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 . CAUTION : Failure to follow the predisassembly pro c edures can result in equipmen t damage or data loss.
7. Connect the front panel U SB (1 and 2), front audio (3), and front power/LED (4) cables to the system board as shown i n the following diagram. Figure 5-37 Connecting the front pan el I/O device cables 8. Rotate the drive cage down to its normal position.
Speaker This section describes how to remove and install the speaker. Removing the speaker To remove the speaker: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 . CAUTION : Failure to follow the predisassembly pro c edures can result in equipmen t damage or data loss.
Power supply This section describes how to rem ove and install a power supply. Removing the power supply To remove the power supply: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 . CAUTION: Failure to follow the pred isassembly proce dures can result in equipment da mage or data loss.
5. Slide the power sup ply toward the chas sis an d then up to remove it from th e chassis. Figure 5-40 Removi ng power supply Installing the power supply To install the power supply, reverse the previous ste p s.
System fan assembly This section describes ho w to remove and install the system fan assembly. Removing the system fan assembly To remove the system fan assembly: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 .
6. Disconnect the system fan assembly cable from th e system board as shown in the following figure. Figure 5-42 Disconnecting fan wires 7. Remove the fan assemb ly by pushing in on the four release tab s on the front of the chassis (1), and then sliding the fa n assembly into the chassis until you can lift it out.
Memory This section presents memory module (DIMM) conf iguration inf ormation an d removal/installation procedures. Supported DIMM configurations The computer supports th ese DIMM con figurations: ●.
BIOS errors and warnings The BIOS gene rates warnings/ errors on inva lid memory con figurations: ● If the BIOS can find a valid memory configuratio n by disabling plugged-in memory, it does so and reports a warning during POST. the computer ca n still be started.
Removing a DIMM To remove a DIMM: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 . CAUTION: Failure to follow the pred isassembly proce dures can result in equipment da mage or data loss. 2. Remove the access pan el (see Removing the access pa nel on page 71 ).
Installing a DIMM To install the DIMM: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 . CAUTION : Failure to follow the predisassembly pro c edures can result in equipmen t damage or data loss. 2. Remove the access panel (see Removing the access panel on page 71 ).
5. Align the DIMM connector key with the DIMM socket key, and then seat the DIMM firmly in the socket (1). CAUTION: DIMMs and their sockets are keye d for proper installation. To prevent socket or DIMM damage, align these guides pr operly when in stalling DIMMs.
Expansion card slot identification This section identifies and de scribes computer expans ion card slots, and presents card configuration information. Slot identification and description The following fig ure ident ifies comput er expans ion card slot s.
Choosing an expansion card slot Whenever possible , use the followi ng tips to help you select the proper slot for an expansion card: ● Use the black PCIe x16 I /O slot for the primary graphics card; if you do no t use this slot for the graphics card, only cards certified as After Market Options are supp orted.
Removing and instal ling expansion cards PCIe I/O slots can support other PC Ie cards with less bus bandwidth t han what is physically defined for the slot. Expansion card slot description NOTE: The x1, x4, and x16 designators de scribe the mechan ical length of t he slot.
4. Push down on the expansion card retention clamp levers on the inside of the chassis to open the retention clamp (1) as shown below. Figure 5-50 Releasing the retention clamp 5. If the card slot has a latch, release th e latch (1), and then carefully lift the card from the chassis (2).
Installing an expansion card Visit htt p://www.hp.com/ go/ quickspecs to learn wh ich graphics cards are su pported in the computer, how much memory each graphics card includ es, and graphics card power requiremen ts. To install an expansion card: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 .
4. Remove the expansion card slot cover by pu lling it up, out of the chassis. TIP: Grasp the slot cover between two fingers—one from the inside of the chassis, and one fro m the outside. Figure 5-53 Removing the slot cover 5. Angle the expansion card to Insert it into the expansion card guide.
8. Replace the access pane l (see Installing the access pan el on page 71 ). 9. Restore all connection s and equipment that you removed during the Predisassembly procedure s on page 68 .
Battery This section describ es how to remo ve and inst all the batter y. The battery that comes with the comp uter provides power to the real-time clock and has a minimum lifetime of abou t three years. WARNING! This computer includes a lithium battery.
Installing the battery To install the battery: 1. Confirm the polarity (p ositive or negat ive) of the ba ttery to position it correctly in the battery holder. 2. Angle the battery and place the battery edge under the plastic housin g tab and press gently until it snaps into place.
5. Disconnect the heatsink screws from the system board (1) as shown in the following figure. Figure 5-57 Disco nnecting the heatsink screws 6. Before lifting the heatsink, ge ntly twist the heat sink to break the thermal compound between th e CPU and the heatsink.
CAUTION : Do not overtighten the heatsi nk screws. Overtightening ca n strip the threads in the chassis. 9. Replace the airflow guide. 10. Replace the access panel (see Installing the access pan el on page 71 ). 11. Restore all connections and equ ipment that you removed durin g the Predisassembly procedure s on page 68 .
CPU This section describes how to remove an d install a CPU . Removing a CPU To remove a CPU: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 . CAUTION: Failure to follow the pred isassembly proce dures can result in equipment da mage or data loss.
Installing a CPU NOTE: HP recommends that you do not swap processo rs (CPUs) from one system board to anothe r. To install a CPU: 1. Prepare the compu ter for servicing by follo wing the Predisassembly procedures o n page 68 . CAUTION : Failure to follow the predisassembly pro c edures can result in equipmen t damage or data loss.
System board This section descr ibes replacing t he system bo ard. Removing the system board To remove the system board: 1. Prepare the co mputer for servicing by foll owing the Predisassembly procedures on p age 68 . CAUTION: Failure to follow the pred isassembly proce dures can result in equipment da mage or data loss.
Product recycling HP encourages customers to recycle used electronic h ardware, HP orig inal print cartrid ges, and rechargeable batteries. For information abou t recycling HP components or products, see http://www.
6 Diagnostics and troubleshooting This chapter describes the tools available for di agnosing and troubleshooting system issues, and includes these topics: Topics Calling technical s upport on pa ge 12.
Calling technical support At times you might encounter an issue that requires technical support. When you call technical support: ● Have the computer read ily accessible. ● Write down the computer serial numbers, product nu mbers, model names, and model numbers and have them in front of you.
In general, the serial number labels can be fo und on the top panel or on the si de of the computer and at the rear of the computer (your co mputer may look different). Keep th is number available when contacting customer service for assistance. A product numbe r is generally locate d next to the s erial number.
Diagnosis guidelines If you encounter a probl em with the computer, monitor, or software, the followi ng sections provide a list of general suggestion s that help you isolate and fo cus on the problem before taking further action. Diagnosis at startup ● Verify that the computer a nd monitor are plugged in to a working electrical outlet.
Diagnosis during operati on ● Look for blinking LEDs on the front of the comput er. The blinking lights are error codes that will help you diag nose the problem. Refer to the Diagnostic LED and audible (beep) codes on page 152 section of this document for information on interpreting d iagnostic lights and audible codes.
Troubleshooting checklist Before running diagnostic utilities, use the following checklist to find possible solutions for computer or software prob lems.
HP troubleshooting resources and tools This section provides information on the HP He lp and Support Center, E-support, and Helpful Hints for troubleshooting. HP Support Assistant The HP Support Assis tant is a customized HP user interface th at enhances the Wind ows Vista and Win 7 Help and Support Center function s.
Troubleshooting a problem To help you troubleshoot problems with your syst em, HP provides the Business Support C enter (BSC). The BSC is a portal to an e xtensive se lection of online tools. To a ccess BSC and troubl eshoot a problem with the workstation, complete the following: 1.
At startup ● Verify that the workstation and moni tor are plugged into a working electrical outlet. ● Remove all diskettes, optical disks, and USB drive keys from the drives be fore powering on the workstation. ● Verify that the workstation is turned on and the blue power lig ht is on.
Customizing the monitor display You can manually select or ch ange the monitor model, refresh rates, screen resolution, color settings, font sizes, and power manag ement settings. To do so, right-click the desktop, then click Properties (for Windows XP) or Personalize (for Windows 7 or Windows Vista) to change disp lay settings.
Problem Cause Possible Solution Workstation powered off automatically and the Power LED flashes red 2 times (on ce every second), followed by a 2- second pause, and then two simultaneous beeps sounded. Processor thermal protection is activated. A fan might be blocked or not turning.
Solving diskette problems Table 6- 2 Diskette problems Problem Cause Solution Diskett e drive li ght stays on. Diskette is damaged. 1. Right-click Start , select Explore , and then select a drive. 2. Sele ct File>Pro perties>Tools . 3. Under Error-c hecking, sele ct Check Now.
Problem Cause Solution Invalid system disk is displayed. A diskette that does not contain the system files needed to star t the computer has been inserted into the drive. When drive activity stops, remove the diskette and press the Spacebar. The computer attempts to boot fr om the next device in the boot order.
Problem Cause Solution Nonsystem disk or NTLDR missing message. System is trying to start from a nonbootable diskette. Remove the diskette from the drive. System is trying to start from a damaged hard drive. 1. Insert a bootable diskette into the drive and restart the computer.
Problem Cause Solution The display wo rks properly during the POST but goes blank when the operating system starts. The display settings in the operating system are incompatible with your graphics card and monitor. 1. For Windows, restart your computer in VGA mode.
Problem Cause Solution Fuzzy focus; streaking, gho sting, or shadowing effects; horizon tal scrolling lines; faint vertical bars; or unable to center the picture on the screen (flat-panel monitors using an analog VGA input connection only.
Problem Cause Solution Noise or no sound comes out of the speakers or headphones. 1. If you are using digital spe a kers that have a stereo jack and you want the system to autoswitch to digital, use a stereo-to-mono adapter to en gage the auto sense feature, or use multimedia device properties to switch the audio signal from analog to digital.
the operating system and so make it easy to isolate potential issues t hat may be operating system related versus hard ware. HP Vision Diagnostics benefits are: ● Capture complete system configurat .
Use HP Vision Diagnostics to determine if all the de vices installed on the computer are recog nized by the system and functio n ing properly. Runnin g tests is optional but recommended a f ter installing or connecting a new device.
Downloading and accessing HP Vision Diagnostics Follow these steps to download the HP Vision Diagnostics utility from the HP Web site to a DVD or USB, and then use it to pe rform diagnostics on the computer : 1. Go to http://www.hp.com . 2. Select the Support & Driv ers link.
Accessing HP Vision Di agnostics on the computer The following proc edures describe how to access t he HP Vision Diag nostics utilit ies that are included in the computer software. Creating and using a bootab le USB key This section describ es how to use a U SB key to access the HP Vision Diagnostics.
User interface The HP Vision Diagnostics applicatio n provides six majo r functions, ac cessible thro ugh Tabs. The se functions are: ● Survey — Your current system hardware information. ● Test — List all diagnostics available for your system.
● Miscellaneous — List any devices or data that doesn' t belong to any other Category. ● Processors - Shows system processors. ● Storage — Shows mass storage dev ice s such as floppy drives, optical drives, SATA, SAS hard disk drives and controllers, as well as any RAID arrays.
Test tab The Test tab lists all available diagnostics. The lists have been tailored according to your system configuration. Individual test may be selected or unselected. T he following T est Modes exist: ● Quick — This test selection was picked to perform quickly while covering your entire hardware.
5. Click the Start Test button to start the testing. The Status tab, whic h allows you to monitor the progress of the tests, is automa tically displayed during the testing process. When the tests are complete, the Status tab shows whether the devices passed or failed.
Status tab The Status tab shows the overall pro gress and status of the test scenario as we ll as the progress and status of each test. The col or coded status are black, blue, gre en, red, and orang e.
● The Recommended Repair will give a recommended action that shou ld be performed to resolve the failed ha rdware. ● The Warranty ID is a unique error code associated with the specific error on your computer. When contacting the HP Supp ort Center for assistance with a hard ware failure, please be prep ared to provide the Warr anty ID.
Saving and printing informat ion in HP Vision Diagnostics You can save the informa t ion displayed in the HP Vision Diagnostics Survey, History and Errors tabs to a diskette or a USB flash drive.
Activity Poss ible cause Recommended action Red Power LED blinks two times, once every second, followed by a two-second pause. Two beeps. CPU thermal prote ction activated by either of the following methods: ● A fan might be blocked or not turning. ● The heatsink and fan assembly is not properly attached to the CPU.
Activi ty Possible cause Recommended action Red Power LED blinks seven times, once every second, followed by a two- second pause. Seven beeps. System board failure (ROM detected failure prior to video). 1. Clear CMOS. NOTE: Refer to the Maintenance and Service Guide for the computer model for detailed information on clearing CMOS.
Table 6-8 LED color definitions LED state LED colo r Sys tem status Solid Blue System is on. Flashing Blue System is in Standby. Solid or flashing Red System has experie nced an error. (See POST error messages on page 156 .) None No light System is in Hibernate, or is off.
POST error messages The Power-On Self Te xt (POST) is a series of di ag nostic tests that runs auto matically when the compu ter is powered on. Audible and visual messages occur before the operating system starts if the POST encounters a problem.
Screen message Probable cause Recommended ac tion 164—Memory Size Error Memory configuration is incorrect. 1. Run the Computer Setup (F10) Utility or the Windows utilities. 2. Verify that the memory modules are installe d properly. 3. If third-party memory ha s been added, test the memory configuration using HP memory.
Screen message Probable cause Recommended action 214—DIMM Configuration Warning DIMMs are not installed corre ctly (not paired correctly). See the service label on the computer access panel for the correct memory configurations, and reseat the DIMMs accordingly.
Screen message Probable cause Recommended ac tion 515—CPU Overtemp occurred Insufficient processor cooling or processor defect. 1. If necessary, add a heatsink to the processor and ensure proper operation. 2. Replace the processor. 516—Chipset fan not detected Chipset fan missing, disconnected, or defective .
Screen message Probable cause Recommended action 919—Multi-Bay Riser No t Connected Multi-Bay riser mechanism is missing or is not connected. 1. Replace or reconnect the missing Multi-Bay mechanism to the system board. 2. Reseat or replace the missing mechanism cable.
Screen message Probable cause Recommended ac tion 1803—Processor feature set is insufficient for current system settings Processor feature set is insufficient for current system settings. The BIOS settings do not match the support provided by the processor Change the BIOS settings or upgrade the processor.
7 Configuring RAID devices This chapter describe s how to configure SATA RAID devi ces on all Z series computers and includes these topics: Topics Maximum hard drive configurations on page 162 Configuring SATA RAID devices on page 163 For additiona l information about configuring RAIDs, see htt p://www.
Configuring SATA RAID devices This section describes h ow to use the Intel® Rapid Storage Manager option ROM Configurati on utility to set up and manage SATA RAID volumes.
Configuring system BIOS Configure the system BIOS to enable embedded SATA RAID functionality. 1. To enter the system BIOS setup, press F10 . 2. Use the arrow keys to hi ghlight th e desired language, and then press Enter . 3. Use the arrows to highlight Storage>Storage Options , and then press Enter .
Creating RAID volumes To create RAID volume s, use the Intel Rapid Storage Manager option ROM Configuration utility. 1. To enter the Intel Rapid Storage Manager option ROM Configuratio n utility, press Ctr l+l when prompted.
8 Configuring password security and resetting CMOS This chapter describes how to configure p assword security and to rese t CMOS, and includes thes e topics: ● Preparing to configure passwords on pa.
Resetting the password jumper Use the following proced ure to disable the power-on or setup pa ssword features and clear the power- on and setup passwords.
WARNING! To reduce the risk of pe rsonal injury from e lectrical shock and hot sur faces, discon nect the power cord from the wall outlet and allow the internal system com ponents to cool before touching. CAUTION: When the computer is plugged in, the power supply has voltage app lied to the system board, even when the computer is powe red off.
5. Select File->Apply Defaults and Exit , and then press F10 to accept. 6. Reset the comput er passwords and configuration informat ion, such as the system date and time.
A Connector pins Keyboard Pin Signal 1 2 3 Data Unused Ground 4 5 6 +5 VDC Clock Unused Mouse Pin Signal 1 2 3 Data Unused Ground 4 5 6 +5 VDC Clock Unused RJ-45 Eth ernet Pin 10/100–MbSignal 1000.
USB Pin Signal 1 2 3 4 +5 VDC - Data + Data Ground Microphone cable, 6.35 MM (1/8 inch) Pin Sign al 1 (Tip) 2 (Ring) 3 (Shield) Audio Power Ground Headphone cable, 6.35 MM (1/8 inch) Pin Sign al 1 (Tip) 2 (Ring) 3 (Shield) Audio_Left Audio_ Right Ground Audio line-in cable, 6.
SATA drive Pin Signal Pin Sign al Pin Sig nal Data C able Power Cable Power Cable S3* A- P3 3.3V power P10 Ground S4 Ground P4 Ground P11 Reserved S5** B- P5 Ground P12 Ground S6** B+ P6 Ground P13 12.
Display port Pin Signal Pin Signal 1 ML_Lane 0(p) 11 GND 2 GND 12 ML_Lane 3(n) 3 ML_Lane 0(n) 13 GND 4 ML_Lane 1(p) 14 GND 5 GND 15 AU X CH( p) 6 ML_Lane 1(n) 16 GND 7 ML_Lane 2(p) 17 AUX C H(n) 8 GND.
PWRCMD—Power command, P2 4 PWROK Gray 5 GND Black 6 PSU_DETECT (empty) CPU power cable, P3 Pin Color Signal 1 BLK GND 2 BLK GND 3 BRN 12V CPU 4 BRN 12V CPU CAUTION: Never connect the PCIe power cable to the system board when power is on. If you do so, the system board can be damaged an d the warranty voided.
Internal USB 2 2x5 Pin Si gnal 1 +5V 2 +5V 3 USB7# 4 USB8# CAUTION : Possible equipment damage. The 2x5 connector can be mated to either a wide 2x5 option cable connector or a narrow 1x5 option cable connector.
B System board designators This appendix describ es the system board designators for this computer. Designator Silk screen Component/Description E15 E15 Crisis recovery header/jumper E49 E49 Clear pas.
Designator Silk screen Component/Desc ription P160 SATAPWR1 HDD power (black) XBT1 XBT1 BAT Battery holder XMM1 - XMM4 XMM1 - XMM4 DIMM1 - DIMM4 Memory slots XU1 XU1 Primary CPU socket ENWW 177.
C Routine Care General cleaning safety precautions ● Never use solvents or flammable solutions t o clean the comp uter. ● Never immerse any compone n t in water or cleaning so lutions; apply any liquids to a clean cloth and then use the cloth on the component.
● Clean under a key with a swab mo istened with isopropyl alcohol and squ eezed out. Be careful not to wipe away lu bricants necessary for proper key functions. Allow the parts to air dry before reassemb ly. ● Use tweezers to remove any fibe rs or dirt in confined are as.
D Locating HP resources This section provide s information on the following HP resources for you r computer: Topics Product information on page 181 ● HP Cool Tools ● Regulatory information ● Acc.
Product information Table D -1 Product information Topic Location HP Cool Tools Most HP Microsoft Win dows computers are preloaded with additional software that is not automatically installed during first boot. Additionally, a number of valuable tools on your computer are preinstalled that may enhance system performance.
Product support Table D-2 Product support Topic Location Additional information For online access to technical support information and tools, see www.hp.com/ go/bizsupp ort . Support resources include Web-based troubleshooting tools, technical knowledg e databases, driver and patch downloads, online communities, and proactive notification services.
Product documentation Table D -3 Product documentation Topic Location HP user documentatio n, white papers, and third-party documentation For the latest online documentation, see http://www.
Product diagnostics Table D-4 Product diagnostics Topic Location Diagnostics tools The HP Vision Diagnostics utility can be downloaded from the HP Web site. To use this utility, refer to the appropriate section of the computer Maintenance and Ser vice Guide .
Product updates Table D -5 Product updates Topic Location Software, BIOS, and driver updates See http://www.hp.com/ go/bizsupport to verify that you have the latest drivers for the computer. To locate the current computer BIOS on yo ur Microsoft Windows computer, select Start>Help and Support>Pick a Task>Use Tools to view.
Index A Appendices Connector pins iii System board designato rs iii B BIOS Determining version 20 Updating 21 BIOS ROM 28 C Cable management 93 Computer Setup (F10) Uti lity Menu description 29 Config.
R Red Hat Linux Setting up 16 removal and replacement drives 76 removing bezel blanks 78 Replacing compone nts Access panel 71 access panel sensor 74 access panel solenoid 76 Battery 65 cable lock 69 .
Ein wichtiger Punkt beim Kauf des Geräts HP Z200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP Z200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP Z200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP Z200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP Z200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP Z200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP Z200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP Z200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP Z200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
