Benutzeranleitung / Produktwartung LaserJet M401dn des Produzenten HP
Zur Seite of 211
L ASER JET PRO 4 0 0 Us er Guide M401.
.
HP LaserJet Pro 400 M401 Printer Series User Guide.
Copyright and License © 2012 Copyright Hewlett-Packard Development Company, L.P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice.
Table of contents 1 Product introd uction . ............. ........... ............ ............ ............ ............ ............ ............ ...... .. 1 Product view s ............ .............. ................ ................ ..............
Change the settings for a ll print jobs until the softwa re program is closed .............. ......... 26 Change the default se ttings for all pri nt jobs ........ ................................. ...................... 26 Change the p roduct configura tion settings .
Use AirPrint .......... ........... ........... ............ ........... ............ .......... ........... ............ ........... ... ......... 54 Walk-up USB printing .......... ................ .............. .................. ................ .
Change the toner cartridge ............... ................ .............. ................ ............... .......... 77 Memory .... .......... .......... .......... .......... .......... .......... .......... .......... .......... .......... .......
Install bl ack cartridge ............................................................................... 92 Invalid driv er Press [OK] . .......................................................................... 92 Jam in <location> ..... ......
Print a cleaning page (touchsc reen control panel) ....... ................. ............... 108 Inspect the toner cartrid ge for damage .............. ...................... ................... ............. 108 Check the pa per and printing e nvironment .
The product name does not appe ar in the product list in the Print & Fax or Print & Scan list ..... .......... .......... .......... ..........
x ENWW.
1 Product introduction ● Product views ● Print product reports ● Printer sharing disclaimer ENWW 1.
Product views Product front view 1 Output bin 2T r a y 1 3 Power button 4T r a y 2 5 Walk-up USB port (HP LaserJet Pro 400 M401dn Pr inter and HP LaserJet Pro 400 M40 1dw Printer only) 6 Toner cartrid.
Product back view 1 Hi-Speed USB 2.0 port 2 Network port (all models except HP LaserJet Pro 400 M401a Printer and HP LaserJet Pro 400 M401d Printer) 3 Power connection 4 Slot for a cable-type security.
Control panel layout LCD control panel 1 Control-panel display: The display prov ides information about the product. Use the menus on the display to establish product settings. 2 Attention light (amber): The Attention lig ht blinks when the product requires user attention.
9 Setup button: This button prov ides quick access to the Setup menu. 10 LED light: This light is no t functional on this product. Touchscreen control panel NOTE: The touchscreen control panel is available on the HP LaserJet Pro 400 M401dn Printer mo del and the HP LaserJet Pro 400 M401dw Pri nter model.
9 Left arrow button and ligh t: moves the cursor to the left NOTE: This button illuminates only when the current screen can use this featu re. 10 Home button and light: provides access to the Home scr.
Touchscreen Home screen NOTE: The touchscreen control panel is available on the HP LaserJet Pro 400 M401dn Printer mo del and the HP LaserJet Pro 400 M401dw Pri nter model. The Home screen provides access to the produ c t features, and it indicates the product st atus.
Print product reports Product reports reside within the product memory. These pages help diagnose and solve problems with the product. NOTE: If the product language was not correctly set during installation, yo u can set the language manually so the information pages print in one of the supported lan guages.
Print product reports from a touchscreen control panel 1. From the Home screen on the prod uct control panel, touch the Setup button. 2. Touch the Reports button.
10 Chapter 1 Prod uct introducti on ENWW.
2 Paper tray ● Supported paper sizes ● Supported paper types ● Load the input trays ENWW 11.
Supported paper sizes This product supports a nu mber of paper sizes, and it a dapts to various media. NOTE: To obtain best results, select the c orrect paper size and type in the print driver before printing.
Table 2-1 Supported pa per and print media sizes (conti nued) Size and dimensions Tray 1 Tray 2 Optional 500- sheet Tray 3 Duplexer (duplex models only) Envelope Commercial #10 105 x 241 mm (4.13 x 9.49 in) Envelope B5 ISO 176 x 250 mm (6.7 x 9.8 in) Envelope C5 ISO 162 x 229 mm (6.
Supported paper types For a complete list of specific HP-brand paper that this product supports, go t o www.hp.com/ support/ ljm401series . Paper type (control panel) Paper type (print driver) Tray 1 .
Load the input trays Load Tray 1 1. Open Tray 1, and pull the t ray extension away from the product. 2. For long paper, flip ou t the extension to help hold the paper in the tray.
3. Place the paper stack int o Tray 1, and slide the paper guides so that they are against the sheets. 4. Feed the paper stack into the tray as far as it will go.
2. Slide open the pap er length and width guides by pushing outward on the blue tabs. 3. To load Legal-size paper, extend t he tray by pressing the release butt on at the back of the tray inward and pulling the back of the tray out. NOTE: When loaded with Legal-size paper, the tray extends from the rear of the product approximately 70 mm (2.
5. Push down on the paper to make sure that t he paper stack is below th e pa per limit tabs on the right side and rear of the tray. 6. Slide the tray into the product.
2. Slide open the pap er length and width guides by pushing outward on the blue tabs. 3. To load Legal-size paper, extend t he tray by pressing the release butt on at the back of the tray inward and pulling the back of the tray out. NOTE: When loaded with Legal-size paper, the tray extends from the rear of the product approximately 70 mm (2.
5. Push down on the paper to make sure that t he paper stack is below the paper limit ta bs at the rear of the tra y. 6. Slide the tray into the product.
3P r i n t ● Supported printer drivers (Windows) ● Change print-job settings (W indows) ● Change print-job settings (Mac OS X) ● Print tasks for Windows ● Print tasks for Mac OS X ● Additi.
Supported printer drivers (Windows) Printer drivers provide access to the product featur es and allow the computer to communicate with the product (using a printer l anguage). Check the installation notes and re adme files on the product CD for additional software and languages.
● Developed to align with the Windows Graphic Device Interface (GDI) for the best speed in Windows environments ● Might not be fully compatible with third-party and c ustom software programs that .
Change print-job settings (Windows) Priority for changing print-job settings Changes to print settings are prioritized depending on whe re the ch anges are made : NOTE: The names of commands and dia log boxes might vary depending on your software pro gram.
Change the product configuration settings 1. Windows XP, Windows Server 2003, and Windows Server 2008 (using the default Start menu view) : Clic k Start , and then click Printers and Faxes . Windows XP, Windows Server 2003, and Windows Server 2008 (using the Classic Start menu view) : Click Start , click Settings , and then click Printers .
Change print-job settings (Mac OS X) Priority for changing print-job settings Changes to print settings are prioritized depending on whe re the ch anges are made : NOTE: The names of commands and dia log boxes might vary depending on your software pro gram.
3. Click the Options & Supplies button. 4. Click the Driver tab. 5. Configure the installed o ptions. ENWW Change print-job settings (Mac OS X) 27.
Print tasks for Windows Use a printing shortcut (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button. 3. Click the Printing Shortcuts tab. 4. Select one of the shortcuts, and then click the OK button.
Create a printing shortcut (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button. 3. Click the Printing Shortcuts tab. 4. Select an existing shortc ut as a base. NOTE: Always select a shortcut before adjusting any of the settings on the right side of the screen.
5. Select the print option s for the new shortcut. NOTE: You can select the print options on this tab or on any other tab in the printer driver. After selecting options on other tabs, return to the Printing Shortcuts tab before continuing with the next step.
Automatically print on bo th sides with Windows NOTE: This section applies to the HP LaserJet Pro 400 M401d Printer , HP LaserJet P ro 400 M401dn Printer, a nd HP LaserJet Pro 400 M401dw Printer models only. 1. On the File menu in the software program, click Print .
3. Click the Finishing tab. 4. Select the Print on both sides check box. Click the OK button to print the job. Manually print on both sides with Windows NOTE: This section primarily applies to the HP LaserJ et Pro 400 M401a Printer and HP LaserJet Pro 400 M401n Printer models.
2. Select th e product, and then click the Properties or Preferences button. 3. Click the Finishing tab. 4. Select the Print on both sides (manually) check box.
5. Retrieve the printed stack from the output bin and, maintaining the same orientation, place it in Tray 1 with the printed sid e down and the top of the pages toward the product. 6. On the control panel, press the OK button to print the second side of the job.
3. Click the Finishing tab. 4. Select the number of pa ges per sheet from the Pages per sheet drop-dow n list. 5. Select the correct Print page borders , Page order , and Orientation options.
Select the page orientation (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button. 3. Click the Finishing tab. 4. In the Orientation area, select the Portrait or Landscape option.
Select the paper type (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button. 3. Click the Paper/Quality tab. 4. From the Paper type drop-down list, click the More..
5. Select the category of paper types that best describes your paper. 6. Select the option for the ty pe of paper you are using, and click the OK button. Print the first or last page on different paper (Windows) 1. From the software program, select the Print option.
2. Select th e product, and then click the Properties or Preferences button. 3. Click the Paper/Quality tab. 4. Click the Print pages on different paper item, and th en click the Settings button to select the necessary sett ings for the front cover, other pages, and back cov er.
Scale a document to fit page size (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button. 3. Click the Effects tab. 4. Select the Print document on option, and then select a size from the drop-down list.
Create a booklet (Windows) 1. From the software program, select the Print option. 2. Select th e product, and then click the Properties or Preferences button.
4. Click the Print on both sides or Print on both sides (manually) check box. 5. In the Booklet layout drop-dow n list, select a binding option. The Pages per sheet option automatically changes to 2 pages per sheet .
Print tasks for Mac OS X Use a printing preset (Mac OS X) 1. On the File menu, click the Print option. 2. In the Printer menu, select this product. 3. In the Presets menu, select the printing preset. 4. Click the Print bu tton. NOTE: To use print driver defa ult settings, select the standard option.
Manually print on both sides (Mac OS X) NOTE: This section primarily applies to the HP LaserJ et Pro 400 M401a Printer and HP LaserJet Pro 400 M401n Printer models.
Print multiple pages on on e sheet of paper (Mac OS X) 1. On the File menu, click the Print option. 2. In the Printer menu, select this product. 3. Open the Layout menu. 4. From the Pages per She et menu, s elect the number of page s that you want to print on each sheet (1, 2, 4, 6, 9, or 16).
4. Select a type from the Media-type drop-down list. 5. Click the Prin t button. Print a cover page (Mac OS X) 1. On the File menu, click the Print option. 2. In the Printer menu, select this product. 3. Open the Cover Page menu, and then select w here to p r int the cover page.
Additional print tasks (Windows) Cancel a print job (Windows) 1. If the print j ob is currently printing, cancel it by pressing the Cancel button on the product control panel. NOTE: Pressing the Cancel button clea rs the job that the product is currently processing.
5. Type a name for the custom size and specify the dimensions. ● The width is the short edge of the paper. ● The length is the long edge of the paper. NOTE: Always load paper into th e trays short edge first. 6. Click the Save button, and then click the Close button.
Additional print tasks (Mac OS X) Cancel a print job (Mac OS X) 1. If the print j ob is currently printing, cancel it by pressing the Cancel button on the product control panel. NOTE: Pressing the Cancel button clea rs the job that the product is currently processing.
4. Click the Watermark chec k box. 5. Beneath the check box, use the drop-down lists to set the various watermark eleme nts. 6. Click the Print bu tton.
Create archival-quality prints Archive print produces output that is less susceptibl e to toner smearing and d usting. Use archi ve print to create documents tha t you want to pres erve or archive. NOTE: Archival-quality printing is accomplished by in creasing the temperature of the fuser .
Use HP ePrint Use HP ePrint to print documents by sending them as an email attachment to the product's email address from any email enabled device. NOTE: The product must be connected to a wired or wir eless network and ha ve Internet acces s to use HP ePrint.
Set up HP ePrint (touchscreen control panel) 1. To use HP ePrint, you must first enable HP Web Services. a. From the Home screen on the product control panel, touc h the We b Services button.
Use AirPrint Direct printing using Apple’s AirPrint is supported for iOS 4.2 or later. Use AirPrint to print directly to the product from an iPad ( iOS 4.
Walk-up USB printing The HP LaserJet Pro 400 M401dn Printer and HP Laser Jet Pro 400 M401dw Printer models feature printing from a USB flash drive, so that you ca n quickly print files without sending them from a computer. These products accept standard USB storag e accessories in the USB port on the front of the products.
56 Chapter 3 Print ENWW.
4 Manage and maintain ● Use the HP Reconfiguration Utility to change the product connect ion ● Set up HP Wireless Direct Printing ● Use HP Web Services applications ● Configure IP network sett.
Use the HP Reconfiguration Utility to change the product connection If you are already using the prod uct and you wish to change the way it is connected, use the HP Reconfiguration Utility to set up the connection.
Set up HP Wireless Direct Printing NOTE: This feature is available with wireless models only. The HP Wireless Direct Printing feature lets you prin t from your wireless mobile device directly to an HP Wireless Direct-enabled produc t without requiring connection to an establishe d network or the Internet.
Use HP Web Services applications Several innovative applications are available for this product that you can download directly from the Internet. For more information an d to download these applications go to the HP ePrintCenter Web site at www.hpeprintcenter.
Configure IP network settings View or change network settings Use the HP Device To olbox to view or change IP configuratio n settings. 1. Print a configuration page, and locate the IP address. ● If you are using IPv4, the IP address contains only digits.
5. Use the nume ric keypad to enter the subnet mask, and touch the OK button. Touch the Yes button to confir m. 6. Use the numeric keypad to enter th e default gateway, and touch the OK button.
Link speed and duplex settings NOTE: This information applies only to Ethernet netw orks. It does not apply to wirele ss networks. The link speed and co mmunication mode of the pr int server must match the network hub. For most situations, leave the produc t in automatic mode.
Setting Description 10T Full 10 Mbps, full-du plex operation 10T Half 10 megabytes per second (M bps), half-duplex operation 100TX Full 100 Mbps, full-duplex operation 100TX Half 100 Mbps, half-duplex operation 5. Touc h the OK button. The product turns off and then on.
HP Device Toolbox (Windows) Use the HP Device Toolbox for Windows to view or change product settings from your computer. This tool opens the HP Embedded Web Server for the prod uct. NOTE: This tool is available only if you performed a full installation when you installed the product.
Tab or section Description Print tab Provides the ability to change default print settings from your computer. ● Printing : Change the default product print setti ngs, such as number of copies and paper orientation. These are the same opti ons that are available on the control panel.
HP Utility for Mac OS X Use the HP Utility for Mac OS X to view or change pr oduct settings from your computer. This tool opens the HP Embedded Web Server for the product. You can use the HP Utility when the product is c onnected with a USB ca ble or is connected to a TCP/IP- based network.
HP Web Jetadmin HP Web Jetadmin is an award-winni ng, industry-lea ding tool for effi ciently managing a wide variety of networked HP devices, including printers, multifunction products, and digital senders.
Product security features The product supports se curity standards and recomm ended protocols that help you keep the product secure, protect critical information on your netw ork, and simplify the way you monitor and maintain the product. For in-depth information about HP's secure imaging and printing solutions, visit www.
4. Type the new passwo rd in the New Password box and in the Verify password box. 5. At the bottom of the window, click the Apply button to save the password.
Economy settings Print with EconoMode This product has an EconoMode option for printing drafts of documents. Us ing EconoMode can use less toner and dec rease the cost per pag e. However , using EconoMode can also reduce print quality. HP does not recommend the full-time use of EconoM ode.
Set the sleep delay (touchscreen control panel) 1. From the Home screen on the prod uct control panel, touch the Setup button. 2. Open the following menu s: ● System Setup ● Energy Settings ● Sleep Dela y 3. Select the time for the sleep delay. NOTE: The default value is 15 Minutes .
Set the Auto Power Down dela y (touchsc reen control panel) 1. From the Home screen on the prod uct control panel, touch the Setup button. 2. Open the following menu s: ● System Setup ● Energy Settings ● Auto Power Down ● Auto Power Down Delay 3.
Print when a toner cartridge is at estimated end of life Black Low : The product indicates when a toner cartridg e level is low. Actual toner cartridge life remaining may vary. Consider having a replacement av ailable to install when print quality is no longer acceptable.
Enable or disable the At Very Lo w settings (touchscreen control panel) You can enable or disable the default settings at any time, and you do not have to re-enable them when you install a new toner cartridge. 1. From the Home screen on the prod uct control panel, touch the Setup button.
Store and recycle supplies Recycle supplies To recycle a genuine HP toner cartridge, place the used cartridge in the box in w hich the new cartr idge arrived. Use the enclosed return label to send the used supply to HP for recycling. For complete information, see the recycling guide that is included with each new HP supply item.
Replacement instructions Change the toner cartridge When a toner cartridge approaches the end of usef ul life, you are prompted to order a replac ement. You can continue printing with th e current cartridge until redistributing the toner no longer yiel ds acceptable print quality.
3. Grasp both sides of the toner cartridge and distribute the toner by gently ro cking the cartridge. CAUTION: Do not touch the shutter or t he surface of the roller. 4. Bend the tab on the left side of the cartridge until the tab breaks loose. Pull the tab until all the tape is removed from the cartridge.
Memory This product includes a memory panel that will accept the following third-party font and barcode memory modules. Hewlett-Packard does not sell t hese products. ● BarDIMM Pro, Jetmobile ● MicrDIMM Pro, Jetmobile ● TypeHaus Fonts and Barcodes Solutions, TypeHaus, Inc.
Update the firmware HP offers periodic upgrades to the product firmware. You can load the fir mware updates manually, or you can set the product to automa tically load firmware updates. Manually update the firmwa re (LCD control panel) 1. On the prod uct control panel, press the OK button to open the menus.
Set the product to automatically update the firmware (touchscreen control panel) NOTE: This section applies to the HP LaserJ et Pro 400 M401 d Printer model only.
82 Chapter 4 Manage and maintain ENWW.
5 Solve problems ● Solve problems checklist ● Restore the factory-set defaults ● Control panel help system ● Interpret control panel messa ges ● Paper feeds incorrectly or becomes jammed ●.
Solve problems checklist Follow these steps when trying to solve a problem with the product. ● Step 1: Make sure that the product is set up correctly ● Step 2: Chec k the cabling or wireless conne.
Step 3: Check the contro l panel for error messages The product control panel should in dicate ready status. If an error message a ppears, resolve the error. Step 4: Check the paper 1. Make sure that the pape r that you are using meets specifications.
Restore the factory-set defaults Restoring the factory-set defaults returns all of the product and network settings to the factory defaults. It will not reset the page count, tray size, or language. To restore th e product to the factory-default settings, follow these steps.
Control panel help system The HP LaserJe t Pro 400 M401dn Pr inter and HP La se rJet Pro 400 M401dw Printer models have built-in Help systems that explain how to use each screen. To open th e Help system, touch the Help button in the upper-right corner of the scre en.
Interpret control panel messages Control panel message types The control panel mess ages indicate the current pro d uct status or situations that might require action.
50.x Fuser Error Turn off then on Description The product has experienced an error with the fuser. Recommended action Turn the product power off, wait at leas t 30 seconds, and then turn the product power on and wait for it to initialize. Turn off the product, wait at least 25 minutes, and then turn on the product.
Recommended action Turn the product power off, wait at leas t 30 seconds, and then turn the product power on and wait for it to initialize. If you are using a surge protector, remove it. Plug the product directly into the wall socket. Turn the product power on.
If the message persists , contact HP support. 79 Service error Turn off then on Description An incompatible DIMM is installed. Recommended action 1. Turn the product powe r off. 2. Install a DIMM that the product supports. 3. Turn the product on. If the message persists , contact HP support.
Recommended action Wait for the cleaning process to finish. Device error Press [OK] Description An internal error occurred. Recommended action Press the OK button to resume the job. Door open Description The product front door is open. Recommended action Close the door .
Jam in <location> Description The product has det ected a jam. Recommended action Clear the jam from the location indicated. The job should continue to print. If it d oes not, try reprinting the job. If the message persists , contact HP support.
Load tray <X> <TYPE> <SIZE> Description A tray is configured for the paper typ e and size that the prin t job is re questing, but that tray is empty. Recommended action Load the correct paper into the tray, or press the OK button to use paper in a different tray.
To avoid this pr oblem, tr y the following solutions: ◦ Adjust the paper guides in the tray. Make sure the front paper guide is pushing the pa per against the back edge of the tray. ◦ Use paper that meets HP specif ications. Store paper unopened in its original packagi ng.
very low mode wil l not be consider ed to be defects in materials or workmanship in the toner cartridge under the HP Print Cartridge Warranty Statement. Supplies low Description A toner cartridge is low. Recommended action Printing will continue until a Very Low message displays.
Paper feeds incorrectl y or becomes jammed The product does not pick up paper If the product d oes not pick up pape r from the tray, try these solutions. 1. Open the product and remove any jammed sheets of paper. 2. Load the tray with the correct size of paper for your jo b.
Clear jams Jam locations Jams can occur in these locations: 1 Output bin 2 Rear door 3T r a y 1 4T r a y 2 5 Optional Tray 3 Loose toner might remain in the product after a jam. This problem typically resolves itself after a few sheets have been printed.
1. If you can see the jammed sheet, remove the jammed sheet by pulling it straight out. 2. If you cannot see the ja mmed sheet, open the print cartridge door, and then remove the print cartridge.
3. Remove the jammed sheet by pulling it straight out. CAUTION: Do not pull up on th e jammed sheet. Be sure to pull it straight out. 4. Reinstall the print cartri dge, and then close the print cartridge door. Clear a jam in Tray 2 1. Remove the tray from the product.
2. Remove the jammed sheet by pulling it straight out. 3. Replace the tray. 4. Press the OK button to continue printing. ENWW Clear jams 101.
Clear a jam in optional Tray 3 1. Remove the tray from the product. 2. Remove the jammed sheet by pulling it straight out. 3. Replace the tray. 4. Press the OK button to continue printing.
Clear jams from the output bin CAUTION: Do not use s harp object s, such as tw eezers or needle-nose pliers, to remove jams. Damage caused by sharp objects wi ll not be covered by the warranty. 1. With both hands, grasp the pap er, and carefully pull it free from the product.
2. Remove any jammed sheets. NOTE: If the sheet tears, remo ve all fragments before re suming printing. CAUTION: Wait until the fuser area has cooled before clearing the jam. 3. Close the rear do or. Clear a jam in the fuser area 1. Open the rear door.
2. Remove any jammed sheets. NOTE: If the sheet tears, remo ve all fragments before re suming printing. CAUTION: Wait until the fuser area has cooled before clearing the jam.
Improve print quality Check the paper type setting (Windows) Check the paper type setting if you are having any of the following problems: ● Toner is smearing on the printed pages. ● Repeated marks occur on the printed pages. ● Printed pages are curled.
6. Select a type from the Media-type drop-down list. 7. Click the Print bu tton. Check toner cartridge status Print the supplies status page (LCD control panel) Information pages reside within the product memo ry. These pages help diagnose and solve problems with the product.
Print a cleaning page Print a cleaning page to remove dust and excess toner from the paper path if you are having any of the following problems: ● Specks of toner are on the p rinted pages. ● Toner is smearing on the printed pages. ● Repeated marks occur on the printed pages.
2. Check the memory chip for damage. 3. Examine the surface of the imaging drum on the bottom of the toner cartridge. CAUTION: Do not touch the roller (imaging drum) on the bottom of the cartridge. Fingerprints on the imaging drum can cause print-quality problems.
Check the paper and printing environment Use paper that meets HP specifications Use different paper if you are havi ng any of the following problems: ● The printing is too light or seems faded in areas. ● Specks of toner are on the p rinted pages.
Use the print driver that best meets your printing needs You might need to use a different print driver if the printed page has unexpected lines in graphics, missing text, missing graphics, incorre ct formatting, or substituted fonts. HP PCL 6 dri ver ● Provided as the default driver.
The product does not print or it prints slowly The product does not print If the product does not print at all, try the following solutions. 1. Make sure the product is turned on and th at the control panel indi cates it is ready. ◦ If the control panel does not indicate the prod uct is ready, turn the product off and then on again.
The product prints slowly If the product prints, but it seem s slow, try the following solutions. 1. Make sure the computer meets the minimum spec ifications for this product. For a list of specifications, go to this Web site: www.hp.co m/ support/ljm401s eries .
Solve walk-up USB printing problems NOTE: This section applies only to the HP LaserJet Pro 400 M401 dn Printer and HP Las erJet Pro 400 M401dw Printer models.
The file that you want to print is not listed in the USB Flash Drive menu 1. You might be trying to print a file type that the USB printing feature does not support. The product supports .PDF and .JPEG file types. 2. You might have too many files in a single fold er on the USB storage accessory.
Solve direct connection problems If you have connected the product dire ctly to a computer, check the cable. ● Verify that the cable is connected to the computer and to t he product. ● Verify that the cable is no t longer than 5 m (16.4 ft). Try using a shorter cable.
Solve wired network problems NOTE: This section applies to all models except the HP LaserJet Pr o 400 M401a Printer and HP LaserJet Pro 400 M401d Pr inter models. Check the following items to verify that the pr oduct is communicating wi th the network.
The computer is unable to communicate with the product 1. Test network communication by pinging the network. a. Open a command-line prompt on your computer. Fo r Windows, click Start , click Run , an d then type cmd . b. Type ping followed by the IP addr ess for your prod uct.
Solve wireless network problems NOTE: This section applies to the HP LaserJ et Pro 400 M401 dw Printer model only. Wireless connectivity checklist ● Verify that the network cable is not connected. ● Verify that the product and the wireless router ar e turned on and have power.
4. Make sure that your computer is working co rrectly. If necessary, restart the computer. 5. Try manually configuring the pro duct from the control panel. The product does not print, and the computer has a third-party firewall installed 1. Update the firewall with the most recent update available from the manufacturer.
The wireless network is not functioning 1. Make sure that the networ k cable is not connected. 2. To verify if the network has lost communication , try connecting other devices to the network. 3. Test network communication by pinging the network. a. Open a command-line prompt on your computer.
Reduce interference on a wireless network The following tips can reduce inte rference in a wire less network: ● Keep the wireless devices away fr om large metal object s, such as filing cabinets, and other electromagnetic devices, such as mic rowaves and cordless telephones .
Solve product software problems with Windows A print driver for the product is not visible in the Printer folder 1. Reinstall the product software. NOTE: Close any applications that are running. To close an ap plicatio n that has an icon in the system tray, right-click the icon, and select Close or Disable .
Windows 7 a. Click Start . b. Click Devices and Printers . c. Right-click the product driver icon, and then select Printer properties . d. Click the Ports tab, and then click Configure Port .
Solve product software problems with Mac OS X ● The print driver is not listed in the Print & Fax or Print & Scan list ● The product name does not appear in the produc t list in the Print .
A print job was not sent to the product that you wanted 1. Open the print queue and restart the print job. 2. Another product w ith the same or similar name might have received your prin t job.
Remove software (Windows) Windows XP 1. Click Start , and then click Programs . 2. Click HP , and then c lick the produc t name. 3. Click Uninstall , and then follow the onscreen instructions to remove the software. Windows Vista and Windows 7 1. Click Start , and then click All Programs .
Remove software (Mac OS X) You must have administrator rights to remove the software. 1. Disconnect the product from the computer. 2. Open Applications . 3. Select Hewlett Packard . 4. Select HP Uninstaller . 5. Sele ct the product from th e list of devices, and then click the Uninstall button.
6 Supplies and accessories ● Order parts, ac cess ories, and supplies ● HP policy on non-HP supplies ● HP antico unterfei t Web site ENWW 129.
Order parts, accessories, and supplies HP original toner cartridge and paper www.hp.com/ go/suresupply Order genuine HP parts or accessories www.hp.com/ buy/parts Order through service or support providers Contact an HP-authorized service or support provider.
Index A accessories ordering 129, 130 AirPrint 54 amber light 4 anticounterfeit supplies 130 applications downloading 60 apps button 7 Apps menu 60 archival-quality printing creating 51 LCD control pa.
home button 5 Home screen, control panel 7 HP Device Toolbox, us ing 65 HP Embedded Web Server changing network settings 61 changing passwor d 69 changing product name 62 opening 61, 62, 69 HP ePrint .
selecting custom sizes (Mac) 49 selecting custom sizes (Windows) 47 paper type checking settings 106 paper types selecting (Mac) 45 selecting (Windows) 37 paper, covers printing (Mac) 46 printing (Win.
supplies status page 8 printing 107 T TCP/IP manually configuring IPv4 parameters 61 toner cartridge checking for damage 108 checking status 107 door release, locating 2 low threshold settings 74 part.
.
© 20 1 2 Hew lett-P ack ar d Dev elopment C ompan y , L.P . www .hp.com.
O Opuscoli stampa (Mac) 46 stampa (Windows) 41 Ordinazione materiali di consumo e accessori 134 Ordinazione di materiali di consumo siti Web 133 Orientamento modifica ( Mac) 45 modifica (Windows) 36 O.
Risoluzione dei problemi alimentazione della carta 98 con alimentazione carta 98 connessione USB 117 elenco di controllo 8 4 inceppamenti 98 Mac 1 27 messaggi del pannello di controllo 88 nessuna risp.
T TCP/IP configurazione manuale dei parametri IPv4 61, 62 Test diagnostico rete wireless 123 Tipi di carta selezione (Mac) 45 selezione (Windows) 37 tipi di carta sup portati 14 Tipo carta controllo d.
6 DUT N E D E R L A N D S VEILIGHEIDSINSTRUCTIES Brenggeenveranderingenaaninhetproductendemonteerofrepareerhetniet.
7 DUT N E D E R L A N D S VEILIGHEIDSINSTRUCTIES A TTENTIE Installeerhetproductuitdebuurtvanapparatendiewerkenmetradiogolven.
© 20 1 2 Hew lett-P ac kar d De v elopment Com pan y , L.P . www .hp.com *CF270-90917* *CF270-90917* CF270-90917.
9 DUT N E D E R L A N D S VEILIGHEIDSINSTRUCTIES Hetproductiszwaar .Probeerdusnooitomhetalleenteverplaatsenofuitte pakken.Doeditsamenmetiemandanders. Anderskuntuzichbezeren.
10 DUT N E D E R L A N D S INST ALLA TIEPROCEDURE/MONTERENENVOORBEREIDEN OPMERKING UwTVkanafwijkenvandegetoondeafbeelding. DeOSD(schermweergave)vanuwTVkanenigszinsafwijkenvandeafbeeldingenindeze handleiding.
1 1 DUT N E D E R L A N D S MONTEREN EN VOORBEREIDEN Afstandsbediening en batterijen (AAA-formaat) (Zie pag. 19) Gebruikershandleiding Kabelhouder (afhankelijk van het model) (Zie pag. A-6) Reinigingsdoekje (afhankelijk van het model) Hiermee kunt u de behuizing afstoffen.
12 DUT N E D E R L A N D S MONTEREN EN VOORBEREIDEN Standaard/basis van standaard (Alleen 19/22/26LS35**) (Zie pag. A-3) Standaard/basis van standaard (Alleen 32LS35**) (Zie pag. A-3) Standaard/basis van standaard (Alleen 26CS46**) (Zie pag. A-4) Standaard/basis van standaard (Alleen 32/42CS46**, 32/42LS340*) (Zie pag.
13 DUT N E D E R L A N D S MONTERENENVOORBEREIDEN A TTENTIE Netsnoerinstallatiegids - SluithethetbijdeTVmeegeleverdenetsnoeropdejuistewijzeaanalsditlijktophetnetsnoerin onderstaandeafbeelding.
14 DUT N E D E R L A N D S MONTEREN EN VOORBEREIDEN Onderdelen en knoppen Knop Beschrijving A-type 2 B-type H H Hiermee worden de opgeslagen programma's doorlopen. H H Hiermee regelt u het volumeniveau. OK ꔉ H Hiermee wordt de gemarkeerde menuoptie gekozen, of een invoer bevestigd.
15 DUT N E D E R L A N D S MONTERENENVOORBEREIDEN DeTVoptillenen verplaatsen LeeshetonderstaandealsudeTVwiltoptillenof verplaatsenomtevoorkomendatdeTVgekrast ofbeschadigdraakt,enalsudeTVveiligwilt vervoeren,ongeachthettypeenafmeting.
16 DUT N E D E R L A N D S MONTERENENVOORBEREIDEN Opeentafelbladplaatsen 1 Tilde TVop,kanteldezerechtopenzetdeTV ophettafelblad. - Laateenruimtevrijvan(minimaal)10cm vanafdemuurvooreengoedeventilatie.
17 DUT N E D E R L A N D S MONTERENENVOORBEREIDEN DeTVaaneenmuurbevestigen (Dezefunctieisniet opallemodellenbeschikbaar .) 1 BevestigdeoogboutenofdeTV -steunenmet schroevenaandeachterkantvandeTV .
18 DUT N E D E R L A N D S MONTERENENVOORBEREIDEN Aaneenmuurmonteren Bevestigvoorzichtigeenoptionele muurbevestigingssteunopdeachterkantvande TVenmonteerdemuurbevestigingssteunaaneen massievemuurdieloodrechtopdevloerstaat.
19 DUT N E D E R L A N D S AFST ANDSBEDIENING AFST ANDSBEDIENING De be sch ri jvi ng en in d eze h and le idi ng g aan u it va nd e toe ts en op de a fst an dsb ed ien in g. Le es dez e han dl ei din g aan da cht ig do or en b edi en d e TV op d ej ui ste w ijz e.
20 DUT N E D E R L A N D S DEGEBRUIKSAANWIJZINGGEBRUIKEN DEGEBRUIKSAANWIJZINGGEBRUIKEN MetdegebruiksaanwijzingkuntudeuitgebreideTV -informatiegemakkelijkeroproepen. 1 Drukop SETTINGS voortoegangtotde hoofdmenu’s.
21 DUT N E D E R L A N D S ONDERHOUD/PROBLEMENOPLOSSEN O N D E R H O U D D e T V s c h o o n m a k e n V o or d e b e s te p r es t a t ie s e n e e n l a n g er e l ev e n s du u r m oe t u d e T V re g e l ma t i g s c h o on m a k en .
.
ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΤΗ ΤΗΛΕΟΡ ΑΣΗ LED LCD / ΤΗΛΕΟΡ ΑΣΗ LCD Πριν θέσετε σε λειτουργία τη συσκευή, διαβάστε προσεκτικά τ ο παρόν εγχειρίδιο και φυλ άξτε το σε ασφαλές μέρος για μελλοντική αναφορά.
2 ELL ΕΛΛΗΝΙΚΑ ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ ΠΙΝΑΚΑΣ ΠΕΡΙΕΧΟΜΕΝΩΝ 3 ΑΔΕΙΕΣ ΧΡΗΣΗΣ 3 ΣΗΜΕΙΩΣΗ ΓΙΑ ΤΟ ΛΟΓΙΣΜΙΚ Ο ΑΝΟΙΧΤΟ Υ .
3 ELL ΕΛΛΗΝΙΚΑ ΑΔΕΙΕΣ ΧΡΗΣΗΣ / ΣΗΜΕΙΩΣΗ ΓΙΑ Τ Ο ΛΟΓΙΣΜΙΚ Ο ΑΝΟΙΧΤΟ Υ ΚΩΔΙΚΑ ΑΔΕΙΕΣ ΧΡΗΣΗΣ Οι υποστηριζ όμενες άδειες χρήσης ενδέχεται να διαφέρουν, ανάλογα με τ ο μοντέλο.
4 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ Ο ΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦ ΑΛΕΙΑ Προτ ού χρησιμοποιήσετε τη συσκευή, διαβάστε προσεκτικ ά τις οδηγίες σχετικά με την ασφάλεια.
5 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ Μην συνδέετε μεγάλο αριθμό ηλεκτρικ ών συσκευών σε ένα πολ ύπριζ ο. Υπάρχει κίνδυνος πρόκλησης πυρκαγιάς λ όγω υπερθέρμανσης.
6 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ Μην αποσυναρμο λογήσετε, μην επισκευάσετε και μην τρο ποποιήσετε τ ο προϊόν με δική σας πρωτ οβουλία.
7 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ ΠΡΟΣΟΧΗ Μην το ποθετείτε το προϊόν σε μέρη με π αρεμβολές ραδιοκυμάτ ων.
8 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ Μην ενεργοπ οιείτε/απενεργοποιείτε τ ο προϊόν συνδέοντας ή αποσυνδέοντ ας το φις του καλ ωδίου από την πρίζ α.
9 ELL ΕΛΛΗΝΙΚΑ ΟΔΗΓΙΕΣ ΣΧΕΤΙΚΑ ΜΕ ΤΗΝ ΑΣΦΑΛΕΙΑ Κατά τη μετ αφορά ή την αφαίρεση του προϊόντος από τη συσκευασία του, ζ ητήστε τη βοήθεια δεύτερου ατόμου, γιατί το προϊόν είναι βαρύ.
10 ELL ΕΛΛΗΝΙΚΑ ΔΙΑΔΙΚΑΣΙΑ ΕΓΚΑ Τ ΑΣΤ ΑΣΗΣ / ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ ΣΗΜΕΙΩΣΗ Η εικόνα μπορεί να διαφέρει από την τηλεόρασή σας.
1 1 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Τ ηλεχειριστήριο και μπ α- τ αρίες (AAA) ( Ανατρέξτε στη σελ.
12 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Σώμα βάσης/Βάση στήριξης (Μόνο στα μοντέλ α 19/22/26LS35**) (Ανατρέξτε στη σελ. A-3) Σώμα βάσης/Βάση στήριξης (Μόνο στα μοντέλ α 32LS35**) (Ανατρέξτε στη σελ.
13 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ ΠΡΟΣΟΧΗ Οδηγός εγκατάστ ασης καλωδίου τροφοδοσίας - Αν τ ο κα.
14 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Εξαρ τήματα κ αι κ ουμπιά Κουμπί Περιγραφή Τ ύπος Α 2 Τ ύπος B H H Κύλιση στα απ οθηκευμένα προγράμματα.
15 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Α νύψωση κ αι μετ ακίνηση της τηλεόρασης Πριν από τη μετακίνηση .
16 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Επιτραπέζ ια το ποθέτηση 1 Σηκώστε και το ποθετήστε την τηλεόραση σε κατακ όρυφη θέση επάνω σε ένα τραπέζι.
17 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Στερέωση της τηλεόρασης σε τ οίχο (Η λειτουργία αυτή δεν είναι διαθέσιμη σε ό λα τα μοντέλα).
18 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΑΡΜΟΛ ΟΓΗΣΗ ΚΑΙ ΠΡΟΕΤΟΙΜΑΣΙΑ Επιτ οίχια τ ο ποθέτηση Συνδέστε προσεκτικά μια προαιρετική επ.
19 ELL ΕΛΛΗΝΙΚΑ ΤΗΛΕΧΕΙΡΙΣΤΗΡΙΟ ΤΗΛΕΧΕΙΡΙΣΤΗΡΙΟ Οι περιγραφές σε αυτό το εγχειρίδιο βασίζ ονται στα κ ουμπιά του τηλεχειριστηρίου.
20 ELL ΕΛΛΗΝΙΚΑ ΧΡΗΣΗ Τ Ο Υ Ο ΔΗΓΟ Υ ΧΡΗΣΗΣ ΧΡΗΣΗ Τ Ο Υ Ο ΔΗΓΟ Υ ΧΡΗΣΗΣ Ο Οδηγός χρήσης σάς επιτρέπει να αποκτήσετε εύκ ολη πρόσβαση στις λεπτομερείς πληροφορίες της τηλε- όρασης.
21 ELL ΕΛΛΗΝΙΚΑ ΣΥΝΤΗΡΗΣΗ / ΑΝΤΙΜΕΤΩΠΙΣΗ ΠΡΟΒΛΗΜΑ ΤΩΝ ΣΥΝΤΗΡΗΣΗ Κ αθαρισμός της τηλεόρασης Καθαρίζετε τακτικ ά .
.
B-1 MAKING CONNECTIONS MAKING CONNECTIONS y This section on MAKING CONNECTIONS mainly uses diagrams for the LS35** models. Antenna connection ANTENNA/ CABLE IN 13/18V 700mA Max LNB IN Satellite English Connect the TV to a wall antenna socket with an RF cable (75 Ω).
B-2 MAKING CONNECTIONS Satellite dish connection (Only satellite models) ANTENNA/ CABLE IN 13/18V 700mA Max LNB IN Satellite English Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω).
B-3 MAKING CONNECTIONS Ελληνικ ά Συνδέστε την τηλεόραση σε μια δορυφορική κε- ραία, μέσω μιας δορυφορικής υποδο χής με δορυ- φορικό καλ ώδιο (75 Ω).
B-4 MAKING CONNECTIONS Français 1 Connectez le câble d’antenne au port d’entrée de l’antenne du téléviseur . 2 Branchez l’adaptateur CC sur la prise d’alimentation du téléviseur . 3 Connectez d’abord le câble d’alimentation à l’adaptateur CC, puis branchez le câble d’alimentation sur une prise murale.
B-5 MAKING CONNECTIONS Deutsch Überträgt digitale Video- und Audiosignale von einem externen Gerät an das TV -Gerät. V erbinden Sie das externe Gerät, wie in der folgenden Abbildung gezeigt, mithilfe des HDMI-Kabels mit dem TV -Gerät. Wählen Sie zum Anschließen einen beliebigen HDMI-Eingang.
B-6 MAKING CONNECTIONS Português T ransmite os sinais digitais de vídeo e áudio de um dispositivo externo para a TV . Ligue o dispositivo externo à TV com o cabo HDMI, conforme demonstrado na seguinte ilustração. Escolha qualquer porta de entrada HDMI para ligar .
B-7 MAKING CONNECTIONS Ελληνικ ά Μεταδίδει τ α ψηφιακά σήματα εικ όνας και ήχ ου από μια εξωτερική συσκευή στην τηλεόραση.
B-8 MAKING CONNECTIONS Deutsch Überträgt analoge Video- und Audiosignale von einem externen Gerät an das TV -Gerät. V erbinden Sie das externe Gerät, wie in der folgenden Abbildung gezeigt, mithilfe eines Komponenten- Kabels mit dem TV -Gerät.
B-9 MAKING CONNECTIONS Français Permet de transmettre les signaux audio et vidéo analogiques d’un périphérique externe vers la TV . Connectez le périphérique externe et la TV avec le câble composite comme indiqué sur l’illustration suivante.
B-10 MAKING CONNECTIONS USB connection USB IN USB (*Not Provided) English Connect a USB storage device such as a USB ash memory , external hard drive, or a USB memory card reader to the TV and access the My media menu to use various multimedia les.
B-1 1 MAKING CONNECTIONS CI module connection y Image shown may differ from your TV . English View the encrypted (pay) services in digital TV mode. This feature is not available in all countries. NOTE y Check if the CI module is inserted into the PCMCIA card slot in the right direction.
B-12 MAKING CONNECTIONS Nederlands Bekijk gescrambelde services (betaalservices) in de digitale TV -modus. Deze functie is niet in alle landen beschikbaar . OPMERKING y Controleer of de CI-module in de juiste richting is geplaatst in de PCMCIA- kaartsleuf.
B-13 MAKING CONNECTIONS Deutsch Überträgt Video- und Audiosignale von einem externen Gerät an das TV -Gerät. V erbinden Sie das externe Gerät, wie in der folgenden Abbildung gezeigt, mithilfe des Euro-Scart-Kabels mit dem TV -Gerät. V erwenden Sie das Euro-Scart-Kabel, um Bilder im V ollbildmodus anzuzeigen.
B-14 MAKING CONNECTIONS Português T ransmite os sinais de vídeo e áudio de um dispositivo externo para a TV . Ligue o dispositivo externo à TV com o cabo Euro Scart, conforme demonstrado na ilustração seguinte. Para apresentar imagens com varrimento progressivo, não se esqueça de utilizar o cabo Euro Scart.
B-15 MAKING CONNECTIONS Deutsch V erbinden Sie verschiedene externe Geräte mit dem TV -Gerät, und wechseln Sie die Eingangsmodi, um ein externes Gerät auszuwählen. Weitere Informationen zum Anschluss von externen Geräten entnehmen Sie bitte dem Handbuch des jeweiligen Gerätes.
B-16 MAKING CONNECTIONS Français Connectez divers périphériques externes à la TV et changez de mode de source d’entrée pour sélectionner un périphérique externe. Pour en savoir plus sur le raccordement d’un périphérique externe, reportez-vous au manuel fourni avec ce dernier .
B-17 MAKING CONNECTIONS Español Puede conectar varios dispositivos externos al TV y cambiar entre los modos de entrada para seleccionar un dispositivo externo. Para obtener más información sobre la conexión de dispositivos externos, consulte el manual que se incluye con cada dispositivo.
B-18 MAKING CONNECTIONS Nederlands U kunt diverse externe apparaten aansluiten op de TV en de invoerbron wijzigen om het externe apparaat te kiezen. Zie voor meer informatie over het aansluiten van externe apparaten de handleiding die bij elk extern apparaat is geleverd.
B-19 SPECIFICA TIONS SPECIFICA TIONS Product specications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product.
B-20 SPECIFICA TIONS MODELS 32LS345* 42LS345* 32LS341* 32LS3450-ZA 32LS345S-ZA 32LS345T -ZA 42LS3450-ZA 42LS345S-ZA 42LS345T -ZA 32LS341C-ZA Dimensions (W x H x D) With stand ( mm) 73 8.0 x 5 01.0 x 185 .0 972. 0 x 635 .0 x 212.0 738.0 x 5 01.0 x 1 85.
B-21 SPECIFICA TIONS HDMI-PC supported mode Resolution Horizontal Frequency (kHz) V ertical Frequency (Hz) 640x350 31.468 70.09 720x400 31.469 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1 152x864 54.348 60.053 1360x768 47.712 60.
Ein wichtiger Punkt beim Kauf des Geräts HP LaserJet M401dn (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP LaserJet M401dn noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP LaserJet M401dn - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP LaserJet M401dn reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP LaserJet M401dn erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP LaserJet M401dn besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP LaserJet M401dn verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP LaserJet M401dn. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP LaserJet M401dn gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
