Benutzeranleitung / Produktwartung E0K41UAABA des Produzenten HP (Hewlett-Packard)
Zur Seite of 96
HP ENVY m6 Sleekbook HP ENVY Touchsmart m6 SleekBook HP ENVY TouchSmart m6 Ultrabook Maintenance and Service Guide IMPORTANT! This docume nt is intended for HP authorized service providers only.
© Copyright 2013 Hewlett-Packard Development Company, L.P. AMD, the AMD Arrow log o, and combinations thereof, are trademarks of Advanced Micro Devices, Inc. Intel is a trademark of Intel Corporation in the U.S. and other countries. Microsoft and Windows are U.
Safety warning notice WARNING! To reduce the possibility of heat-related in juries or of overheating the device, do not place the device directly on your la p or obstruct the device air vents.
iv Safety warning notice.
Table of contents 1 Product description .................... .............. ........... ................ ............... .............. .............. ... 1 2 External component identification ............... ............ ............ ......... ......
Service cover ........... ........... ........... ........... ........... ........... ......... ........... ........... ......... 30 Battery .. .......... ............ .......... .......... ........... ............ ........... .......... .............
7 Backup and recovery ............................. .......................... .................. ........................... .. 7 6 Backing up your information ............. ............ ............ ............ ............ ............. ..........
viii.
1 Product description Category Desc ription Intel models AMD models Produc t Names HP ENVY TouchSmart m6 Ultrabook √ HP ENVY TouchSmart m6 Sleek book √ HP ENVY m6 Sleekbook √ Processo rs Intel® Core™ i7-4500U (1.8 GHz, turbo up to 3.0 GHz) 1600 MHz/4 MB Cache, Dual 15W √ Intel Core i5-4200U (1.
Category Desc ription Intel models AMD models Memory Supports up to 16 GB max system memory (DDR3L-1600MHz Dual Channel Support) in the foll owing configurations: ● 16384 MB (8192 MB x 2) ● 12288 .
Category Desc ription Intel models AMD models Supports Intel Wireless Display (WiDi/WiFi Direct support) √√ 2 WLAN antennas built into display assembly √√ Supports the following WLAN formats: ● Intel Wireless-N 7260BN 802.11 bgn 2x2 WiFi + BT 4.
Category Desc ription Intel models AMD models Ports ● 3-pin AC Smart Pin adapter plug ● Audio-in (mono microphone)/ Audio-out (stereo headphone) combo jack, supports jack detection ● HDMI version 1.4 supporting 1920 ×1200 @ 60Hz ● RJ-45 (Ethernet, includes link and activity lights) ● USB 3.
Category Desc ription Intel models AMD models Operating system Preinstalled: ● Windows 8.1 (64 bit) ● Windows 8 (64 bit) ● Windows 8 Standard ● Windows 8 Professional √√ Serviceability End.
2 External component identification Display Component Des cription (1) Internal microphones (2) Record sound. (2) Webcam light ● On: The webcam is in use. ● Off: The webcam is not in use. (3) HP TrueVision HD Webcam Records video, captur es still photo graphs, and provides access to video conferences and online chat by means of streaming video.
Component Des cription (4) Internal display switch Turns off the display and init iates Sleep if the display is closed while the power is on. NOTE: The internal display switch is not visible from the outside of the computer. (5) WLAN antennas (2)* Send and receive wirele ss signals to communicate with wireless local area networks (WLANs).
Top TouchPad Component Des cription (1) TouchPad zone Moves the on-screen pointer and selects or activates items on the screen. NOTE: The TouchPad also supports edge-swipe gestures. (2) Left TouchPad button Functions like th e left button on an external mouse.
Lights Component Des cription (1) Power light ● On: The computer is on. ● Blinking: The comput er is in the Sleep state, which is an energy-saving mode. The computer shuts off power to the display and other unneeded compon ents. ● Off: The computer is off or in Hibernation.
Buttons and speakers Component Description (1) Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the bu tton briefly to exit Hibernation.
Keys Component Des cription (1) esc key Reveals system information when pres sed in combination with the fn key. (2) fn key Executes frequently used s ystem functions when pressed in combination with the b key or the esc key. (3) Windows key Returns you to the Star t screen from an open app or the Windows desktop.
Left side Component D escription (1) Security cable slot Attaches an option al security cable t o the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
Component D escription (6) Hard drive light ● Blinking white: The hard drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. (7) Power light ● On: The computer is on. ● Blinking: The computer is in th e Sleep state, which is an energy-saving mode.
Right side Component Description (1) Audio-out (headphone) jack/Audio-in (microphone) jack Connects optional powered stereo s peakers, headphones, earbuds, a headset, or a television audio cable. Also connects an optional headset microphone. This jack does not support optional microphone-only devices.
Bottom Component Des cription (1) HP Triple Bass Reflex Subwoofer Provides superior bass sound. (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components an d prevent overheating.
Service label When ordering parts or requesting information, provide the computer serial number and model number provided on the service la bel, which is found on the bottom of the computer. Item Component Description (1) Serial number (s/n ) This is an alphanumeric identi fier that is un ique to each produc t.
3 Illustrated parts catalog Computer major components Computer major components 17.
Item Component Spare part number (1) Display assembly (39.6 mm [15.6-in], Brightview, WLE D) Touchscreen models: ● FHD 727459-001 ● HD 727460-001 Non-touchscreen models: ● FHD 727461-001 ● HD .
Item Component Spare part number 2-GB memory module (PC3L, 12800, 1600-M Hz) 691739-005 4-GB memory module (PC3L, 12800, 1600-M Hz) 691740-005 8-GB memory module (PC3L, 12800, 1600-MHz) (Intel models only) 693374-005 (11) Hard drive 750-GB, 5400 RPM, 2 .
Item Component Spare part number For use only in Intel models 728133-001 For use only in AMD models 727465-001 (20) Fan 725445-001 (21) RJ-45 cover 727464-001 (22) Battery (3-cell, 5.
Display assembly subcomponents Item Component Spare part number (1) Display bezel 725442-001 (2) Webcam/microphone module 725465-001 (3) Hinge brackets For use in non-touch models 725448-001 For use in touchscreen models 725449-001 (4) Raw display panel, 39.
Item Component Spare part number For use in non-touch models 725439-001 For use in touchscreen models 725440-001 Miscellaneous parts Component Spare p art number AC adapter (non-smart): 65-W AC adapter (non-smart) for use in all countries and regions 710412-001 Power co rd (3-pin, black, 1.
Spare part number Description 715050-001 3 cell, 50 WHr 4.52AH Li-ion battery 717384-005 Intel Centrino Wirel ess-N 2230 + Bluetooth com bo w/ *2 antennas (802.11 b/g/n, Bluetooth 4.0 ) for use only in Intel models 724935-005 Broadcom 4352 + Bluetooth combo w/ *2 antenn as (802.
Spare part number Description 725462-501 System board with AMD A10-5745M proces sor for use with models with the Windows 8 Standard operat ing syste m 725464-001 Top cover for use in models with an AM.
4 Removal and replacement procedures CAUTION: This computer does not have user-replace able pa rts. Only HP authorized service providers should perform the removal and replac ement procedures de scribed here. Access ing the internal part could damage the computer or void the warranty.
Cables must b e handled with extre me care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Ha ndle cables by the connector whenever possib le. In all cases, avoid bending, twisting, or tearing cables.
CAUTION: To prevent damage to the computer when you are removing or instal ling internal components, observe these precaution s: Keep components in their e lectr ostatic-safe containers until you are ready to install them. Before touching an electr onic compone nt, discha rge static elec tr icity by using the guidelines described in this section.
Packaging and transp orting guidelines Follow these grounding guidelines when packagin g and transporting equipment: ● To avoid hand co ntact, transport pr oducts in static-safe tube s, bags, or boxes . ● Protect ESD-sensitive part s and assemblies with co nductive or approved co ntainers or packaging.
Equipment guidelines Grounding equipment must include either a wrist st rap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a gr ounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords.
Component replacement procedures This chapter provides remova l and replacement procedures. There are as many as 114 screws that must be removed, replaced, or lo osened when servicing the computer. Make special note of each s crew si ze and loc ation during removal and replacement.
2. Remove the 8 remaining larger Phillips screws fr om the back and the midd le of the service cover. 3. Lift up the cover (1) from the unit at the rear edge and remove the service cover (2) .
Battery Description Spare part number 3 cell, 50 WHr 4.52 AH L i-ion battery 715050-001 Before removing the battery, follow these steps: 1. Shut down the computer. If you are uns ure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system.
RTC battery Description Spare p art number RTC battery 725458-001 Before removing the RTC battery, follow these steps: 1. Shut down the computer. If you are uns ure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system.
Hard drive Description Spare p art number 1 TB, 5400 rpm, 2.5 in 676521-005 750 GB, 5400 rpm, 2.5 in 634250-005 500 GB, 5400 rpm, 7 mm 683802-005 Hard Drive Hardware Kit (includes left and righ t brackets , hard drive cable, and screws) 725447-001 Before removing the hard drive, follow these steps: 1.
Remove the hard drive bracket: 1. Remove the 4 PM2. 0×3.0 screws (1) on the har d drive bracket. 2. Remove the hard drive brackets (2) from the hard drive.
2. Remove the solid-state drive from the connector (2 ) . Reverse this procedure to install the SSD. 36 Chapter 4 Removal an d replacement procedures.
WLAN module Description Spare part number WLAN module for use in both Intel and AMD models: Ralink Wireless + Bl uetooth combo w/ *2 antennas (802.11 b/g/n, Bluetooth 4.
3. Remove the WLAN module by pulling the mo dule away from the slot at an angle (3) . NOTE: If the WLAN antennas are not connected to th e terminals on the WLAN module, the protective sleeves must be installed on the antenna connec tors.
Memory modules Description Spare part number 2-GB memory module (PC3L, 12800, 1600-MHz) 691739-005 4-GB memory module (PC3L, 12800, 1600-MHz) 691740-005 8-GB memory module (PC3L, 12800, 1600-MHz)(Intel models only) 693374-005 Before removing a memory module, follow thes e steps: 1.
RJ-45 module cover Description Spare part number RJ-45 module cover (plastics kit) 727464-001 Before removing the RJ-45 module co ver: 1. Shut down the computer. If you are uns ure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system.
Left speaker/ subwoofer Description Spare p art number Speaker Kit (includes left speaker/subwoo fer and right speaker) 725460-001 The computer includes two separate speakers — a sp eaker on the rig ht side, and a speaker/su bwoofer on the left side.
3. Remove the 2 P hillips PM 2.0×2.0 broadh ead screws (2) that secure the speaker/subwoofer to the computer. NOTE: Make sure the rubber grommets are installed in the screw holes (3) when installing the speaker/subwoofer. 4. Remove the subwoofe r (4) .
Remov e the USB/audio board: 1. Disconnect USB/audio connector cable (1) from the system board. 2. Remove the cable from the adhesive th at secures it to the keyboard frame (2) . 3. Disconnect the USB/audio cable (3 ) . 4. Disconnect the subwoofer speaker cable (4) .
6. Remove the RJ-45 module cover (see RJ-45 modu le cover on page 40 ). 7. Remove the USB/audio board (see USB/audio bo ard on page 42 ). Remove the power co nnector cable: ▲ Remove the power connect or cable from its routing path (1) , and then remove the power connector and cable (2) from the comput er.
3. Lift up on the board to disconnect the conn ector on the bottom of the board from the system board, and then remove the card reader board from t he computer (3) . Reverse this procedure to inst all the card reader board. Fan Description Spare part number Fan 725445-001 Before removing the fan: 1.
2. Remove the 2 Phillips PM2.0×3.0 screws securing the fan to the computer (2) , and then lift the fan upwards (3) . 46 Chapter 4 Removal an d replacement procedures.
System board NOTE: The system board sp are part kit includes replacement thermal material. Description Spare part number System board with AMD A10-5745M process or for use with computer models equippe.
● Heat sink (see Heat sink on page 50 ) ● WLAN module se e (WLAN modul e). Remove the system board: 1. Remove the follo wing cables: ● Right speaker cable (1) ● Power button board cable (2) .
3. Lift the system board up at an angle (2) , and then remove the system board (3) . Reverse this procedure to ins tall the system board. Component re placement procedures 49.
Heat sink Description Spare p art number Heat sink for use in models with AMD processors 725446-001 Heat sink for use in models with Intel processors 728132-001 NOTE: To properly ventilate the computer , allow at least 7.6 c m (3 in) of clearance on the left side of the computer.
2. Remove the heat sin k (2) from the system board. 3. Note the locations of thermal material over th e soldered on pr ocessor on the sys tem board (1) and the bott om of the heat sink that services it (2) . Reverse this procedure to ins tall the heat sink.
Power button board Description Spare part number Power button board 725451-001 Before removing the power bu tton board, follow these steps: 1. Shut down the computer. If you are uns ure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system.
Reverse this procedure to in stall the power button board. Right speaker Description Spare p art number Speaker Kit (includes left speaker/subwoo fer and right speaker) 725460-001 The computer includes two separate speakers — a sp eaker on the rig ht side, and a speaker/su bwoofer on the left side.
2. Rotate the hinge up ward to gain acc e ss to the speaker (3) . 3. Remove the Phillips PM2.0×3.5 broadh ea d screw that sec ures the right speaker (1) . 4. Remove the right speake r from the computer (2) . Reverse this procedure to ins tall the right speaker.
Keyboard NOTE: The keyboard spare part kit incl udes a keyboard cable. Description Spare part number: Keyboard bracket 725441-001 Backlit keyboard for use in the United States 725450-001 Backlit keyboard for use in Canada 725450-DB1 Before removing the keyboard, follo w these steps: 1.
2. Lift up (1) to top of the brac ket, and then remo ve the keyboard assembl y (2) from the computer. 3. Remove the 2 silver Phi llips PM2.0×3.0 screws (1) that secure the keyboard to the bracket, and then remove the keyboard from the bracket (2) . Reverse this procedure to install the keyboard.
TouchPad module Before removing the TouchPad bu tton board, follow these steps: 1. Shut down the computer. If you are uns ure whether the computer is o ff or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external device s connected to the computer.
Display assembly, non-touchscreen Description Spare p art number Display assembly, FHD, non-touch 727461-001 Display assembly, HD, non-touch 727462-001 Before removing the display assembly, follow these s teps: 1.
4. Lift the computer up to an angle (4) , and then pull the display assembly away from the computer (5) . 5. Remove the 2 screw covers (1) and the 2 PhillipsPM 2.0×2.5 screws (2) from the bottom corners of the bezel. 6. Loosen the top edge of the plastic bezel c over (3) from all four sides of the display panel.
8. If you need to remove the display hinges, remove the 5 Phillips PM2.5×3.0 screws (1) that secure each hinge to the display , and th en lift the hinge off the display (2) . The display hinges are available usin g the following spare part num bers: ● 725448-001 : Non-touchscreen models ● 725449-001 : Touchscreen models 9.
Raw display panels are available usin g the following spare part numbers: ● 725454-001 : HD, non-touch ● 725455-001 : HD, touchscreen ● 725456-001 : FHD, non-touch ● 725457-001 : FHD, touchscreen 11. Lift the adhesive strip atop the display panel connecto r on the back of the raw display panel (1) , and then disconnect the display cable.
13. If you need to replace the WLAN antennas and tran sceivers, remove the antennas from routing clips on the side of the display enclosur e (1) , and then lift the antennas out of the display enclosure (2) . The WLAN ante nnas and transceivers rout e to the bottom of the display enclosure.
Display assembly, touchscreen Description Spare p art number Display assembly, FHD, touchscreen 727459-001 Display assembly, HD W LED, touchscreen 727460-001 Before removing the display assembly, follow these s teps: 1.
4. Lift the computer up to an angle (4) , and then pull the display assembly away from the computer (5) . 5. To separate the display enclosure, remove the 2 screw covers (1) and 2 silver Phillips PM 2.5×3.0 screws (2) from the bottom of th e display panel assembly.
7. If you need to replac e the webcam modu le from the display e nclosure, lift the we bcam up to disengage the adhesive tape that se cures the webcam to the enclosure (1) , and then disconnect the webcam cable (2) . 8. If you need to remove the display hinges, from each hinge remove the 3 Phil lips PM 2.
10. If you need to remove the WLAN antennas/transcei vers, lift the tape that secures the transceivers to the display panel (1) (2) , and then lift the antennas/tran sceivers from the di splay panel assembly.
11. If you need to remove the disp lay panel, remove the display cable from the rear of the panel (1) , and (if necessary) remove the WLAN antenna tra nsceiver tape fr om the display panel (2) (3) .
13. If you need to remove the disp lay cable, noting the routing cl ips on the sides of the display enclosure, lift the cable from the displa y enclosure.
5 Setup Utility (BIOS) and System Diagnostics Using Setup Utility Setup Utility, or Basic Input/Outp u t System (BIOS), controls communication between all the input a nd output devices on the s ystem (such as d isk drives, display, keyboard, mouse, and printer).
Navigating and selecting in Setup Utility To navigate and select in Se tup Utility, follow these steps: 1. Turn on or restart the computer, and then press es c while the “Press the ESC key for Startup Menu” message is dis played at the bottom of the screen.
Restoring factory settings in Setup Utility NOTE: Restoring defaults will not change the hard drive mode. To return all settings in Setup Util ity to the values that were set at the factory, follow these steps: 1.
BIOS version information (also known as ROM date and System BIOS ) can be displayed by pressing fn + esc (if you are already in Windows) or by using Setup Util ity (BIOS).
4. Double-click the fi le that has an .exe ext ension (for example, filename .exe). The BIOS installation begins. 5. Complete the installation by follo wing the on-screen instructions. NOTE: After a message on the scree n reports a su ccessful installation, you can delete the downloaded file from your hard drive.
6 Specifications Computer specifications Metric U.S. Dimensions Width 29.16 cm 11.48 in Depth 2.15 cm 8.46 in Height (front to back) 2.11 to 3.19 cm 0.83 to 1.26 in Weight With 6-cell battery 1.60 kg 3.53 lb With 3-cell battery 1.46 kg 3.22 lb Input power Operating voltage and current 19.
39.6-mm (15.6-inch) display specifications Metric U.S. Dimensions Height 16.50 cm 6.50 in Width 25.34 cm 11.60 in Diagonal 33.66 cm 15.60 in Number of colors 262,144 Contrast ratio 200:1 (typical) Bright ness 200 nits (typical) Pixel resolution Pitch 0.
7 Backup and recovery To protect your in formation, use Windows Backup and Restore utilities to back up individual files and folders, back up your entire hard dr ive, create system repair media (select models only) by using the installed optical drive (select models only) or an option al external op tical drive, or c reate system restor e points.
To create a backup u sing Windows Backup and Restore: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, de pending on file size and the speed of the computer. 1.
CAUTION: Some Automatic Repair options will complete ly erase and reforma t the hard drive. All files you have created an d any software installed o n the computer are permanently remove d.
4. Press f11 while the “Press <F11 > for recovery” message is disp layed on the scre en. 5. Follow the on-screen instructio ns. Using Windows 8 operating system media (purchased separately) To order a Windows 8 operating s ystem DVD, go to http://www.
Using Windows Refresh for quick and easy recovery When your computer is not working pr operly and yo u need to regain system stability, the Windows Refresh option allows you to start fres h and keep what is impo rtant to you. IMPORTANT: Refresh removes any traditional applications th at were not originally installed on the system at the factory.
To use the Start screen: 1. On the Start screen, point to the far-right upper or lower corner of the screen to display the charms. 2. Click Settings . 3. Click Change PC settings in the bottom-right corner of the screen, and then select General from the PC settings screen.
8 Power cord set requirements The wide-range input feature of the computer permit s it to operate from a ny line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set in cluded with the computer me ets the requiremen ts for use in the country or region where the equipment is purchased.
Requirements for specific countries and regions Country/region Accredited agency Applicable note number Argentina IRAM 1 Australia SAA 1 Austria OVE 1 Belgium CEBEC 1 Brazil ABNT 1 Canada CSA 2 Chile .
Country/region Accredited agency Applicable note number The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 0.75-mm² conduc tor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of th e agen cy responsible for evaluation in the count ry or region where it will be used.
9R e c y c l i n g When a non-rechargeable or recharge able battery has reache d the end of its useful life, do not dispose of the battery in ge neral household waste .
Index A AC adapter light, identifying 14 AC adapter, spare p art numbers 22 action keys identifying 11 audio, product description 2 audio-in (microphone) jack 14 audio-out (headphone) jack 14 B backup.
J jacks audio-in (microphone) 14 audio-out (hea dphone) 14 network 14 RJ-45 (network) 14 K keyboard product description 4 removal 55 spare part numbers 18, 55 keypad 11 keys action 11 esc 11 fn 11 num.
serviceability, product description 5 slots Digital Media Card 12 security cable 12 solid state drive removal procedures 35 spare part number 24 solid state drive, spare part numbers 19 speakers ident.
Ein wichtiger Punkt beim Kauf des Geräts HP (Hewlett-Packard) E0K41UAABA (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP (Hewlett-Packard) E0K41UAABA noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP (Hewlett-Packard) E0K41UAABA - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP (Hewlett-Packard) E0K41UAABA reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP (Hewlett-Packard) E0K41UAABA erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP (Hewlett-Packard) E0K41UAABA besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP (Hewlett-Packard) E0K41UAABA verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP (Hewlett-Packard) E0K41UAABA. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP (Hewlett-Packard) E0K41UAABA gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
