Benutzeranleitung / Produktwartung DAT24I des Produzenten HP (Hewlett-Packard)
Zur Seite of 38
T ape 5000i, DA T8i DA T24i, DA T40i Installation Guide HP Sur eStor e D A T Internal T ape Drive.
HP SureStore D A T Installation Overvie w (Internal Drives) Internal Drives—Installation Overview Refe r t o: Befo re yo u st art : Check the pack ing list i nside thi s guide. Check syste m prerequisi tes. page 1- 2 Step 1: Check the Drive’ s SCSI ID Chec k the t a pe drive’s SCSI ID.
Copyright © 1998-1999 by He wlett-Packard Limited. The informa t ion c o ntained in this document is subject to change without notice. This documen t contains propriet ary informati o n which is protected by copyright.
iii Contents Internal Driv es—Installat ion Ove rview inside front cov er 1 Installing an “i” Model Drive (internal) Before Y ou St art: Check the Conte nts of th e Box 1-2 Before Y ou St art: C.
iv Inde x Regulatory Information Dat-int.bk Page iv Wednesday , May 26, 19 99 10:46 AM.
1 Installing an “i” Model Drive (internal) HP SureStore models covered: • T ape 5000i •D A T 8 i • DA T24i • DA T40i Dat-int.bk Page 1 Wednesday, May 26, 1999 10:46 AM.
HP SureStore D A T Installati on Guide 1-2 Before Y ou Start: Check the Contents of the Box The foll owing equipment is supplied wit h your HP SureSt ore DA T drive. If anything is damaged or missing, contact the delivery company or your supplier . Spare jumpers for the drives’ SCSI ID switch may als o be supplied.
HP SureStore D A T Installat ion Guide 1-3 Before Y ou Start: Check System Prerequisites T o inst all and use your ne w tape drive , you will need the followi ng: • SCSI ho st adapter • SCSI ribbo.
HP SureStore D A T Installati on Guide 1-4 The DA T 40 drive has a 68-pin wide, high-density SCSI connector . If your computer uses narrow SCSI, use a 68-to-50-pin adapter to connect the DA T40 dri ve (68 pins) into the narrow SCSI bus (50 pins). This adapter must be purchased separa tely (part number C7423A ).
HP SureStore D A T Installat ion Guide 1-5 Backup Software Y ou need backup soft ware that supports t he drive. Applicatio ns usually recognize ta pe drives by their manufacturers ’ internal identifiers rather than their model numbers, so check the table below for the appropriate referenc e for your model.
HP SureStore D A T Installati on Guide 1-6 Step 1: Check the Drive’ s SCSI ID Note Y our HP SureStore DA T drive is sh ip ped with a default SCSI ID of 3, but it can be as signed any unused ID between 0 and 6. Do not use SCSI ID 7, which is reserved fo r the SCSI controller , or SCSI ID 0, which is typically assigned t o the boot disk.
HP SureStore D A T Installat ion Guide 1-7 Figure 1.1 SCSI ID set tings on bac k of HP SureStore Tape 5000i , DAT8i and DAT24i SCSI ID 4 23 5 6 (Default) 1 Dat-int.
HP SureStore D A T Installati on Guide 1-8 Figure 1.2 SCSI ID settings on b ack of HP SureStore D A T40i Installing and Using HP T apeAssure HP T apeAssure allows you to check your computer ’ s current SCSI configuratio n on a W i ndows or Ne tW are system.
HP SureStore D A T Installat ion Guide 1-9 Using HP T apeAssur e Note If the program does not work corre ct ly or hangs during process ing, there may be a compatibilit y proble m with the SCSI card. The current versio n of HP T apeAssure may not suppor t Adaptec 151 0 cards (636 0 chip set) and Symbios cards.
HP SureStore D A T Installati on Guide 1-1 0 Step 2: Set the Configuration Switches (UNIX System s Only) 1 Check the “UNI X Configuration Ins tructions ” in the elect ronic User’s Guide on the HP SureStore T ape CD-ROM for specific advice for your operating system .
HP SureStore D A T Installat ion Guide 1-1 1 Step 3: Prepare the Mounting Bay Caution T o avoid damaging the computer or t ape drive, ens u re t hat the computer is powe red off whil e you instal l the drive. Stati c elect ricity c an d amage el ectr onic c omponen ts.
HP SureStore D A T Installati on Guide 1-12 Using the Con version Kit 1 Unscrew the fo ur screws and remo ve the rails from the tape dri ve. Figure 1.4 R emov ing the drive rails prior to installation in a 3½ -inc h bay 2 Use a screwd ri ver to release the 5¼-i nch front panel f rom the tape drive and remove it .
HP SureStore D A T Installat ion Guide 1-13 3 Fit the 3½-i nch front pane l and push fi rmly until th e panel clicks into place. Figure 1.6 Fit ting the 3½-inc h panel Clips on to p of tape drive Clips o n side of tap e drive Dat-int.
HP SureStore D A T Installati on Guide 1-1 4 Step 4: At tach Mounting Ra ils If your computer requires specia l rails or o ther hardware to install the t ape drive, mount them on the t ape d rive in this st ep. If your computer does not require special mounting hard ware, proceed to step 5 on pag e 1-16 now.
HP SureStore D A T Installat ion Guide 1-15 Figure 1.8 At tac hing the HP NetServer E-series, Vectra, Kaya k or Brio rails to the tape drive Figure 1.9 At tach ing C ompaq rails to the tape drive Use t he four screw s provide d with the rail kit Use the fo ur screw s provide d with the rail kit Dat-int.
HP SureStore D A T Installati on Guide 1-16 Step 5: Insta ll the Drive Note W rite the model name, product number , serial number , and SCSI ID of your drive in the front of this guide for f uture refe rence. The mode l name is on the front of the drive and the product and serial numbers are on a labe l on the bottom of the dr ive.
HP SureStore D A T Installat ion Guide 1-17 Figure 1.11 Sliding th e tape drive into the empt y bay Step 6: Attach Power and SCSI Cabl es 1 Attach a spare power cable from the computer’s internal power supply to the power extension cable, as shown in figure 1.
HP SureStore D A T Installati on Guide 1-18 2 Attach a spare SCSI cable to th e SCSI co nnector . If you are using an e xisting SCSI ca ble, simply attach the d rive to a spare connector on the computer ’ s SC SI ribbon cable, as shown in figure 1 .
HP SureStore D A T Installat ion Guide 1-1 9 Step 7: Secure the Drive 1 Secure th e tape dr ive into place with s crews. If you used mounting hardware t hat scre ws to the front of the comput er , use the scre ws you removed in step 3 to fix the drive in place .
HP SureStore D A T Installati on Guide 1-20 On Completion Once you have comple ted the installati on: • Make sure you have the correct media. • Power on a nd check t hat your ne w drive is operatio nal.
HP SureStore D A T Installat ion Guide 1-21 Check Drive Operation 1 Switch on the computer. The tape drive will run its hardware self-t est, which takes a bout 5 se conds. At the en d of the hardware self- test, both front panel lights shou ld be off.
HP SureStore D A T Installati on Guide 1-22 Insert t he HP SureStor e Tape CD-ROM The HP SureStore Tape CD-ROM contains backup software, as well as drivers, us eful utilities and informat ion about using your tape driv e. 1 Load th e CD-ROM and select home.
HP SureStore D A T Installat ion Guide 1-23 Backup Software T o use the ta pe drive, y ou will need a backup applicat ion or utilit y that supports your tape drive model. Th e HP SureStore Tape CD-ROM contains free backup software for use wit h W indows 95, Windo ws 98, W indows NT and Novell Ne tW are.
HP SureStore D A T Installati on Guide 1-24 Refer to your back up application’s documentation for instructio ns on how to back up and restore dat a. V iew ing th e El ectr oni c User’s Guides Y ou can view t he e l ectroni c User’s Guid es with most current web browsers on any platfo rm.
HP SureStore D A T Installat ion Guide 1-25 Register Y our T ape Drive Y ou must register with HP to ensure that you benefit from the full 3-year Express Exchange 1 warranty period. The se cond and thi rd years o f warranty are subject to registra tion wi thi n 30 days.
HP SureStore D A T Installati on Guide 1-26 2 HP w arrants to you that H P s oftware will not fail to execute i ts programming instructions after the date of purchase, for the period speci fied above, due to defects in material and workmanship when properl y install ed and used.
2 Installation T roubleshooting Dat-int.bk Page 1 Wednesday, May 26, 1999 10:46 AM.
HP SureStore D A T Installati on T r ouble shooting 2-2 Save Y our self a Ca ll The first s tep in proble m-solving is establis hing whether the p roblem lies with the cartridge, the tape drive, the host computer and its connections, or with the way the system is being opera ted.
HP SureStore D A T Installation T roubles hooting 2-3 Problems with Y our Internal T ape Drive P roblem P ossible Cause P otential Solution The tape drive doe s not pow er up. The power c able may no t be connected to the tape drive properly . Make sure that the power c able is firmly conne cted.
HP SureStore D A T Installati on T r ouble shooting 2-4 Other Sources of Information If you experie nce problems using your tape drive after in stalla tion, use HP T ape T ool s to help you diagnose the problem. Y ou will als o find troubleshoo ting information on the HP SureStore Tape CD-ROM an d the HP web site.
Ind ex -1 A access ories, or derin g See electronic User’s Guide anti-static protec tion 1-6 appl icat ions, back up 1-5 , 1-23 B backup applications drives supported 1-5 instal ling 1- 23 backup fa.
Ind ex -2 Novell NetW are backup applications 1- 23 T apeA ssure 1-9 O oper atin g inst ruction s See electronic User’s Guide ordering part s and acces so ries See electronic User’ s Guide P parts.
Regulatory Information Europe Declaration of C onformity (accord ing to ISO/IEC Gu ide 22 and EN 45014) Manufact urer: Hewlett-Pa ckard Company Address: Hewlett -Packard Com pany Compute r Periph eral.
Ein wichtiger Punkt beim Kauf des Geräts HP (Hewlett-Packard) DAT24I (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP (Hewlett-Packard) DAT24I noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP (Hewlett-Packard) DAT24I - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP (Hewlett-Packard) DAT24I reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP (Hewlett-Packard) DAT24I erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP (Hewlett-Packard) DAT24I besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP (Hewlett-Packard) DAT24I verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP (Hewlett-Packard) DAT24I. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP (Hewlett-Packard) DAT24I gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
