Benutzeranleitung / Produktwartung A2969A des Produzenten HP (Hewlett-Packard)
Zur Seite of 55
III’ A2969NA:36M HP-HSC FastlWide Diffkrentid SCSI Adapt,ers Installation and Service.
0 Hewlett-Packard Company, 1997. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Regulatory Statements FCC Statement (For U.S.A. Only) Federal Communications Commission Radio Frequency Interference Statement Warning: This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause interference to radio communications.
About This Book This book is the installation and service manual for the HP A2969AEIP A3644A HP-HSC agh-Speed System Gonnect) Fast/Wide Differential SCSI Adapters. The HP A2969A adapter connects an HP 9000 Series Kxxx computer (using the HP-UX operating system release 10.
Table of Contents 1 Reference Description ................................. .8 Product Contents ........................... .8 spectica.tions ................................ . 2 Installation Procedures InstaUation Overview ...........................
Switch Power on to Peripherals, then to the Computer ................................ ...33 Configure the Operating System and the Adapter ........... .34 Verify Operation .............................. .34 3 Service Information Field Replaceable Units .
1 Reference Contents Description.. ................................................... .8 specifications.. ............................................
Description The Hewlet&Packard &h-Speed astern Connect (HP-HSC) Fast/Wide Differential SCSI Adapter provides the hardware needed to connect an HP 9ooo Series computer to E-bit SCSI devices.
Specifications General Features supported SyStemS j Standards Performance Connector Electrical Power Consumptior HP A2969A HP 9000 Series K&x computers using HP-UX 10.0 or later HP A3644 HP 9000 Series T6xx computer using HP-UX 10.3 or later Complies with ANSI X3T9.
Specifications (continued) Physical Length Width Height Board Thickness 15.11 cm (5.95 in.) 8.76 cm (3.45 in.) 2.54 cm (1.0 in.) 1.5 mm (0.06 in.) Weight 114 g (4.
2 Installation Procedures Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page InstaIIation overview.
Installation Overview 0 . . Figure 1. Installing a SCSI adapter, overview F’lgure 1 presents an overview of installing the adapter in an HP 9000 Series Xxx computer system. The procedure is slightly different for the HF’ 9000 Series T6xx and will be noted where different.
Prepare to Install the Adapter Refer to your computer manuals for any additional information necessary to install the adapter in your computer system. Before installing the adapter, you should perform the following steps: n Observe antistatic precautions.
Record Adapter Information Record the part number and date code of the adapter for future reference. If your adapter requires service in the future, the part number and date code will be needed by HP service personnel. This information is provided on stickers affixed to the adapter.
Shut Down the Operating System and Switch Off the Computer 1. Before installing the adapter, shut down the computer operating system (using shutdown -h 0, not reboot). Refer to your computer system manual for proper shutdown procedures to avoid corruption or loss of data.
Set SCSI Adapter DIP Switches DIP switches on the SCSI adapter are used to set the SCSI address of the adapter. These switches are preset at the factory at address 7 and should not need to be changed unless there are multiple SCSI initiators on the same SCSI bus.
l? L u n Figure 2. DIP switch location InstsUation Procedures 17.
Numbers on Printed-Circuit Card I Address :I 18 lxMallation Procedures.
If Necessary, Remove the Termination Resistors If the SCSI Adapter is installed in the middle of a SCSI bus, that is, not at the end as shown in figure 1 on page 12, the termination resistors on the SCSI Adapter should be removed. (This would only occur in an HA solution with greater than two CPUs, or if a V cable is used.
Install the Adapter For the HP 9000 Series Kxxx computer system, the HP AZ969A SCSI adapter can be installed in a slot in either the core I/O or the HP-HSC expansion I/O. For the HP 9000 Series T6xx computer system, the HP A3644A SCSI adapter is installed in a slot in the HP-HSC I/O bus converter.
Install the HP A2969A SCSI Adapter in an HP 9000 Series Kxxx To instaIl the HP A2969A SCSI adapter in an HP 9000 Series I&xx computer, perform the following steps: 1. 2. 3. 4. 5. Shut down the operating system and turn power off to the computer. (See page 15.
Slot cover screws Figure 4. slot locations Slot covers / Orange stripe indicating top (matches strip on computer) 6. Install the SCSI adapter into the slot in the core I/O or expansion I/O.
Figure 5. Installing the adapter in the I/o bulkhead 8. Press down on the rear of the SCSI adapter until its connector is fully inserted into the receptacle on the core I/O or expansion I/O adapter. 9. Secure the adapter by tightening the two retaining screws (Iocated on the front of the core I/O or expansion YO bulkhead).
Install the HP A3644A SCSI Adapter in an HP 9000 Series T6xx The HP A3644A SCSI adapter (see figure 6) is physically identical to the HP A2969A adapter except for the front bulkhead, thus, the locations of the DIP switch and the termination resistors are the same.
Figure 7. HP-H!3C I/O bus converter To install the HP A3644A SCSI adapter in an HP 9000 Series T6xx computer, perform the following steps: 1. Shut down the operating system and turn power off to the computer. (See page 15.) 2. Wear a grounding wrist strap that is connected to the HP-HSC I/O bus converter bulkhead.
5. Remove the cover blank from the slot where the SCSI adapter is to be mounted. See figure 8. To remove the cover blank, remove the two screws holding the blank in place. The screws are spring loaded. Apply slight upward pressure to prevent the screw from separating from the spring.
6. Install the SCSI card in the HP-HSC converter by pressing the card against the bulkhead of the HP-HSC converter. See figure 9. Figure 9. Installing the HP A3644A card Instalition Procedures 27.
7. Before you push the connector on the SCSI card into the mating connector on the I-EHSC bus converter, turn the captive screws on the HP-HSC bus converter until they engage the SCSI card, but do not tighten the screws. 8. Align the connectors, then press them together securely.
Connect Cable and Peripheral Devices With the adapter installed in the computer, you can now connect the adapter cable and the peripheral devices. SCSI Cable Connection Attach the SCSI cable to the adapter as follows: 1. Inspect the connector pins to be sure they are straight.
Figure 10. Connecting cables to the computer 30 InstaUationAocedmes.
Peripheral Device Connections When connecting SCSI devices, follow these guidelines: Verify the host computer system is shut down. There should be no data transfer activity on the SCSI bus. Verify power is off to the peripheral device before connecting it to the SCSI bus.
Terminate the SCSI Bus Unless the SCSI bus is properly terminated, the bus will not operate properly. Terminators provide matching impedance on SCSI bus signal lines. This product includes an external SCSI bus terminator to terminate the peripheral end of a differential SCSI bus.
Switch Power on to Peripherals, then to the Computer Before applying power to your system, follow these guidelines: 1. Verify all cables are connected and securely fastened. 2. Switch power on to your peripheral devices and wait for them to become ready before you switch power on to your computer.
Configure the Operating System and the Adapter The HP-HSC Fast/Wide Differential SCSI adapter should au&xonfigure into supported HP-UX systems. When the operating system reboots it will determine .
3 Service Information contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Field replaceable units.. ................................ .36 Troubleshooting tools.. ............................
Field Replaceable Units F’ield replaceable units (FRUs) are assemblies or components that are authorized for field replacement. Replaceable FlXJs on the HSC Fast/Wide Differential SCSI adapter: Description Part Number 125V, 2A, LF Fuse 2110-0517 Termination resistors (Removed only during the installation procedure in a multi-jnitiator situation.
Troubleshooting Tools Troubleshooting tools are used to identify faulty adapters. For this product, the following tools are available: n Term Power LED n Off-line diagnostics Term Power LED The termination power (Term Power) LED is green and indicates the adapter is supplying termination power to the SCSI bus.
Replacing the Term Power Fuse To remove and replace the Term Power fuse (F3), proceed as follows: 1. Remove the SCSI adapter from the computer. See the removal instructions on page 42. 2. Pull the fuse out of its socket. The location of the fuse on the SCSI adapter is shown in figure 11.
3. To install the replacement fuse, carefully align the two contact pins with the socket holes. Then press the fuse in (refer to figure 12). The fuse has no polarity, so the pins can go into either socket hole. SCSI Adapter Contact Pins Fuse Socket Fuse part number 21100517 Figure 12.
Off-Line Diagnostics The Off-Line Diagnostic Environment (ODE) is used to test to the I/O adapter level in the computer system. IOTESl’ and MAPPER are modules of ODE that check the functionality of the I/O modules in the computer system. ODE is run from the Initial System Loader (EL) on the system console.
IOTEST ODE> iotest IOTEST> run The IOTEWs strategy is to systematically check the basic functionality of I/O modules in the system. This is accomplished by either making a PDC-IODC call to invoke selftest, or by running a test within the diagnostic.
Removal/Replacement Instructions Removal of the SCSI adapter is the opposite of installation. Follow the instructions presented here and refer to the installation procedures on page 20. CAUTION The adapter contains electronic components that can be damaged by static electricity.
Reshipment Guidelines If any item of the product is to be returned to Hewlett-Packard for any reason, contact your HP Sales and Support Office to coordinate the return. When returning the item, attach a tag that identifies the owner and indicates the reason for shipment.
44 service Information.
Glossary adapter A computer interface card and circuitry that provides the physical connection and data translation between the host computer’s I/O bus and external devices or networks. adapter slot The location where adapters attach to the backplane.
light emltting diode A smaU light emitting device used to provide status information. Mbitdsec Megabits per second (l,OOO,OOO bits per second). medium, media The tmnsmission connection between nodes. Most current I&k use cables (fiberoptic or copper), although radio and other broadcast media are possible.
SCSI bus The collection of SCSI signal lines that interconnect SCSI devices and adapters. SCSI ID SCSI identification. The bit-significant representation of the SCSI address referring to one of the bus signal lines DB (7 - 0,15 - 8). See also SCSI address.
.
Index A A2969AX, 8 A3644Ax, 8 adapter information, 14 antistatic precautions, 13 B bus arbitration, 16 C cable connection, 29 component locations, 16 connect cable and peripheral devices, 29 connect p.
installation antistatic precautions, 13 cable connection, 29 configuring the SCSI adapter into the operating system, 34 connecting cables and peripheral devices, 29 installing the HP A2969A SCSI adapt.
S T SCSI adapter DIP switches, 16 SCSI bus highest priority, 16 SCSI bus, terminating, 32 SCSI Cascade Arrays, 3 1 service information, 35 shut down the operating system, 15 slot locations, 21, 25 spe.
62 Index.
Reader Comment Sheet Fast/Wide Differential SCSI Adapter Installation and Service We welcome your evaluation of this manual. Your comments and suggestions will help us improve our publications. Remove this page, mail or FAX to 9167852875. Use and attach additional pages if necessary.
I BUSINESS REPLY MAIL FLRsrcLAss PERMlT NO. 256 ROSFXILLE. CA I POSTAGE WILL BE PAID BY ADDRESSEE Attention: Learning Products (MS5668) Ill III NECESSARY -I -I -1 -I -1 -/ -r -1 Hewlett-Packard Compan.
Manual Part Number A2969-90001 E0397 HEWLETT PACKARD 0 Copyright 1997 Hewlett-Packard Company Printed in 1J.S.A. A2969-96002 III lllll Ill 11111 lllll llllll II 1111 lllll lllll lllllll.
Ein wichtiger Punkt beim Kauf des Geräts HP (Hewlett-Packard) A2969A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP (Hewlett-Packard) A2969A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP (Hewlett-Packard) A2969A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP (Hewlett-Packard) A2969A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP (Hewlett-Packard) A2969A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP (Hewlett-Packard) A2969A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP (Hewlett-Packard) A2969A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP (Hewlett-Packard) A2969A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP (Hewlett-Packard) A2969A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
