Benutzeranleitung / Produktwartung 5000C/CT des Produzenten HP (Hewlett-Packard)
Zur Seite of 56
1 T his guide is for experienced HP Response Center personnel, CEs, and reseller technicians, such as personnel who have already completed the HP Vectra PC family training course, or equivalent, and have at least six months of experience servicing the HP Vectra PCs.
2 Notice In a continuing effort to improve the quality of our products, technical and environmental information in this document is subject to change without notice.
3 Table of Contents OmniBook Product Comparisons ........................................................................................................... 6 Size Closed ................................................................................
4 Battery Module and Floppy Disk Drive Module (End User Replaceable) ......................................... 26 Hard Disk Drive (End User Replaceable) ........................................................................................ 27 Small parts (End User Replaceable) .
5 Table of Figures Figure 1 - Memory Door and Slot ............................................................................................................... 25 Figure 2 - Floppy Drive and Battery .................................................
6 OmniBook Product Comparisons HP OmniBook 5000 HP OmniBook 4000 HP OmniBook 600 Size Closed 29.5 x 22.6 x 4.9 cm (11.6 x 8.9 x 1.93 in) 29.5 x 22.6 x 4.9 cm (11.6 x 8.9 x 1.93 in) 18.49 × 28.24 × 3.99 cm (11.12 x 7.28 × 1.57 in) Weight 3.08-3.18 kg (6.
7 HP OmniBook 5000 HP OmniBook 4000 HP OmniBook 600 Power 14.4Vdc Rechargeable Lithium-Ion or NiMH battery Battery life (approximate with one battery): 2 to 3 hrs Battery recharges to high level in 4 hrs using AC adapter while PC is on or off 2-minute low-battery warning AC adapter 100 to 240 Vac (50 to 60 Hz) input; 12 Vdc, 3.
8 HP OmniBook 5000 HP OmniBook 4000 HP OmniBook 600 Audio 16-bit with Sound Blaster and MIDI support Stereo sound via two built-in speakers 16-bit, Sound Blaster- compatible Stereo sound via two built-in stereo speakers Microsoft Windows sound in CT.
9 HP OmniBook 5000 HP OmniBook 4000 HP OmniBook 600 Expandability One Type III PCMCIA slot (or use as two Type II slots) with 3.3-V or 5-V support ISA-based slots, and parallel, serial, SVGA- out (up .
10 OmniBook 5000 Series: Product Features Description Premium performance with Pentium processing and PCI bus, optimized for notebook PCs. Models This is a complete list of all the standard OmniBook 5000 models now available. Factory special options are not included in this listing.
11 Product Description Part Number HP OmniBook 5000CT P-75, PCI BUS, 810MB HDD, 16MB RAM, NiMH Battery, VGA TFT Display, One year warranty. F1146A HP OmniBook 5000CT P-90, PCI BUS, 540MB HDD, 8MB RAM, NiMH Battery, VGA TFT Display, One year warranty.
12 Product Description Part Number HP OmniBook 5000CT P-75, PCI BUS, 810MB HD Drive, 8MB RAM NiMH Battery, TFT Display, One year warranty. F1342A HP OmniBook 5000C P-120, PCI BUS, 1.2GB HD Drive, 16MB RAM NiMH Battery, VGA DSTN Display, Three year warranty.
13 Accessories Description Part Number 8-MB RAM expansion card F1134A 16-MB RAM expansion card F1135A 32-MB RAM expansion card F1136A 540-MB Hard Disk Drive F1156A 810-MB Hard Disk Drive F1138A 1.
14 Midi/game port Quick charge while on Local Bus Enhanced IDE Battery charging LCD status Software wake up feature and includes HP PIM Docking connector supports multimedia signals Internal speakers .
15 Expansion Memory Board Options: 8-MB RAM, p/n: F1134A 16-MB RAM, p/n: F1135A 32-MB RAM, p/n: F1136A RAM Manufacturer: Multiple Vendors: NEC, Samsung, etc.
16 Mass storage The hard disk drive can be removed by the user for easy upgrades. The hard drive is located on the bottom case and with the removal of one screw the hard drive can be replaced. Hard drive manufacturer: IBM and Toshiba (subject to change without notice).
17 Sector Size 512 Bytes 512 Bytes 512 Bytes 512 Bytes Recording Zones 4.00 8.00 8.00 8.00 User Cylinders NA NA 3478.00 3478.00 Cylinders 1053.00 1591.00 NA NA User sectors/Track at zone 0 63.00 63.00 NA NA Data Heads 4.00 8.00 4.00 6.00 Disks NA NA 2.
18 Display/Video TFT SVGA Display (CTS Models) Active Matrix TFT VGA Display (CT Models) Active Matrix DSTN Display (C Models) Size 10.4 inches diagonal 10.4 inches diagonal 10.4 inches diagonal Resolution 800 x 600 x 256 colors Refresh: 90ms (18 bit) 640 x 480 x 65,536 colors.
19 TFT displays may have a small number of cosmetic imperfections and still conform to the display manufacturers cosmetic quality specifications. Here are some guidelines to use in determining what action to take on a customer complaint of cosmetic imperfection in their TFT display: 1.
20 Power Battery types: Removable 14.4-Vdc rechargeable NiMH (same as OmniBook 4000) and new Lithium Ion battery [LiIon (OmniBook 5000 only)]. Both battery types do not require complete discharge before recharging. There is no "memory" effect that reduces battery life.
21 AC Adapter: 100 to 240 Vac adapter (50 to 60 Hz) input; 12 Vdc, 2.5 A output. Same adapter as the OB600 (F1044B). OmniBooks will be standardized on the 12 volt adapter. Use only an HP F1044B AC adapter (the type shipped with the OmniBook). Using any other adapter could damage the OmniBook and void the warranty.
22 I/O: Headphone/stereo-out port; microphone port; Stereo-in port IRQ default setting for soundblaster is 5. Audio controller and Manufacturer: CS4232, Crystal Audio controller characteristics: Sampling: 8-48khz Playback rate: 8-48khz Distortion: maximum is 0.
23 Supported Operating Systems MS DOS version 6.22* Microsoft Windows for Workgroups 3.11* Microsoft Windows 95* Microsoft NT workstation 3.51/4.00.** OS/2 version 3.0** * Supported to the application level. ** Only setup and configuration supported.
24 Password Decode Policy The password descramble programs for the HP OmniBook PCs are protected as HP Company Private information. They may not be copied, backed-up, printed or distributed. There are only six official copies of each program. In addition to protecting the program itself, it's use is also controlled.
25 Notebook Hardware Structure Field Replaceable Assemblies Torque Specification: For M2.6 screws; 5.0 +/- 1 in-lb Installing memory (End User Replaceable) Caution: To avoid damage from electrostatic discharge, be sure to ground yourself prior to installation or removal of memory.
26 Battery Module and Floppy Disk Drive Module (End User Replaceable) Caution: Do not mutilate, puncture, or dispose of the battery in fire. The battery can burst or explode, releasing hazardous chemicals. A rechargeable battery pack must be recycled or disposed of properly.
27 Hard Disk Drive (End User Replaceable ) The Hard Disk Drive Module is user replaceable. Caution: Handle the hard disk drive only by its edges to avoid damage from electrostatic discharge. To remove the Hard Disk Drive Module, remove the screw under the latch on the hard drive.
28 Small parts (End User Replaceable) The expansion door, I/O door, rubber feet, and memory door are all replaceable. The remove the I/O door, open it fully. Flex the door so that the center hinge separates from backcase. Continue to flex until side pins clear holes in back case.
29 Icon Assembly and Display Module (HP Authorized Service Providers Only) To remove the display module and/or Icon Assembly on the OmniBook 5000C, CT, and CTS turn the unit over, raise the feet, and withdraw the two Phillips screws from under the feet in the bottom back corners of the unit (see illustration below).
30 Lift the display straight up about 1 inch. The Icon Assembly will lift up with the display. Move the Icon assembly out of the way. The cable from the Icon Assembly to the PC board does not need to be removed if only the display is being removed. Otherwise, slide the connector sleeve up to remove the Icon Assembly cable.
31 To reinstall the display module or Icon Assembly, just reverse the above procedure. Caution: To avoid crimping the Icon Assy Flex Cable, ensure that it is tucked inside of the Icon Assy “tunnel.” When reinstalling the Display Module, make sure that the two posts on either side of the display line up parallel with their slots in the top case.
32 Palm Rest Assembly and Track Ball Assembly (HP Authorized Service Providers Only) Before removing the Palm Rest Assembly or Track Ball Assembly the battery and the floppy disk drive modules (a second battery may be installed in to the floppy disk drive bay) must be removed.
33 To replace, reverse the above procedure. Palm Rest Screw Figure 8 - Palm Rest and Track Ball Assemblies.
34 Keyboard Assembly and Power Board (PCB Assy DC Power PI-DC) (HP Authorized Service Providers Only) To remove the Keyboard Assembly, lift the front edge of the keyboard and rotate the keyboard up. Next, remove the connecting PC board by pulling up on the pull tabs attached to the back.
35 Upper Cover Assembly and Icon Board (PCB Assy PI-ICON) (HP Authorized Service Providers Only) Required Equipment: • Phillips Screwdriver Components to remove prior to Upper Cover: 1. HDD and Battery 2. Icon Assembly and Display Module 3. Palm Rest Assembly 4.
36 5. Remove the Upper Cover by removing the Palm Rest Screw on the left side of the cover. Next, pull the right side outward until it comes off the snap. Once the cover clears the snap, the left side will lift free (see illustration below). The Microphone Assembly may dislodge from the Upper Cover during removal.
37 7. Remove the two screws in the right corner of the Icon Board (PCD Assy PI-ICON). Gently rock the Icon Board forward and back while pulling upward until the pins dislodge from the connector. Replacement Procedure: 1. Reverse the Removal Procedure with the replacement component(s).
38 CPU Module and Heat Sink (HP Authorized Support Providers Only) Required Equipment: • Phillips Screwdriver Components to remove prior to CPU and Heat Sink: 1. HDD and Battery 2. Icon Assembly and Display Module 3. Palm Rest Assembly 4. Keyboard Assembly and Power Board (PCB Assy DC Power PI-DC) 5.
39 CPU Module Heat Sink Print Port Door Expansion Door I/O Door PCMCIA Shield Screw ISOP M2.6x4L Figure 12 - CPU Module and Heat Sink.
40 System Board (PCB Assy PI-586) (HP Authorized Support Providers Only) Required Equipment: • Phillips Screwdriver • Nutdriver (5 mm or 3/16 in) Components to remove prior to CPU and Heat Sink: 1. HDD and Battery 2. Icon Assembly and Display Module 3.
41 Standoff (11.75 mm) Standoff (11.75 mm) Standoff (13.8 mm) Contact Spring Docking Pin Palm Rest Screws (5) IR Lens Bezel Assy Editor’s Note: The PCMCIA Shield must be removed prior to the System Board.
42 Configuration and Setup Main Configuration Screen Pressing [fn][f2] invokes the BIOS setup and configuration utility. Users can check system configuration and changes settings using [f] keys from this screen. This is the most accurate place to check battery and system status.
43 Power Screen The power screen contains the current power level of the main and auxiliary battery. The auxiliary battery charge status does not show up if no auxiliary battery is installed.
44 Power Configuration To implement the power management capabilities, the following settings are set by the user from the power setup screen. Setting: Parameters: Default: Comments: Power Saving Off/On On Enables power saving techniques.
45 System Configuration The system screen contains the processor and memory information for the user to glance at. It also allows the user to set the date and time. The real time clock is not changed until the user exits the setup program. The user can also enable or disable the processor cache.
46 Input/Output Configuration Setting Parameters Default Comments COM Ports Serial Port (None, COM1, COM4) I/R Port ( None, COM1,COM4) Serial Port: COM1, Addr 3F8, IRQ 4 I/R Port: COM2, Addr 2F8, IRQ .
47 Figure 16 - Input/Output Screen.
48 Disk Configuration Setting Parameters Default Comments Floppy Disk Drive Disk A None, 1.44MB, 2.88MB 1.44MB Hard Disk Drive None, Standard, Custom, Auto-ID Auto-ID Also reports disk drive data (# c.
49 Troubleshooting and Repair OmniBook Self-Test The complete self-test procedure is documented in the OmniBook 5000 Operating Guide. A note about interpreting self-test results.
50 Beep Code Description none CPU register test in progress or failure. 1-1-1 CPU Failure 1-1-3 CMOS write/read test in progress or failure. Failure will result in a system halt. 1-1-4 ROM BIOS checksum test in progress or failure. Failure will result in a system halt.
51 3-1-3 Master interrupt mask register test in progress or failure. Failure results in a system halt. 3-1-4 Slave interrupt mask register test in progress or failure. Failure results in a system halt. 3-2-4 Keyboard controller test in progress or failure.
52 Last POST: DISPLAY CODES There are a number of POST tests that are performed after the BEEP Code tests. Failure of one or more of these tests will result in a displayed failure code (i.
53 PhoenixBIOS POST Messages (Power On Self Test) Within POST, there are three kinds of messages: Error messages: These messages appear when there is a failure in hardware, software, or firmware. Informational messages: These messages provide information to the user but require no action.
54 No timer tick interrupt The timer chip has failed. xxxxxh Option ROM checksum failure where xxxxxh is the starting address of the option ROM The peripheral card contains a defective ROM. Shutdown failure Either the keyboard controller is not accepting the reset command or the associated reset logic has failed.
55 Appendix A: Part Numbers Description HP Part Number Exchange Part Number 75N CPU Module F1126-60906 F1126-69006 90N CPU Module F1127-60902 F1127-69002 90C CPU Module F1130-60902 F1130-69002 120C CP.
56 Back Panel Overlay F1125-60930 none Floppy Disk Drive Module F1125-60928 none IBM 810 HDD F1199-60901 F1199-69001 Support Plate L F1125-60931 none Support Plate R F1125-60932 none OB 5000 ENG Rcvy .
Ein wichtiger Punkt beim Kauf des Geräts HP (Hewlett-Packard) 5000C/CT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP (Hewlett-Packard) 5000C/CT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP (Hewlett-Packard) 5000C/CT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP (Hewlett-Packard) 5000C/CT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP (Hewlett-Packard) 5000C/CT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP (Hewlett-Packard) 5000C/CT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP (Hewlett-Packard) 5000C/CT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP (Hewlett-Packard) 5000C/CT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP (Hewlett-Packard) 5000C/CT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
