Benutzeranleitung / Produktwartung 5000 des Produzenten HP (Hewlett-Packard)
Zur Seite of 418
Service Manual DesignJet 5000 and 5500 Series HP Large-Format Printers.
T echnical Marketing, Barcelona Divisi on , Hewlett-Packard Espanola, S.A. A vda. Graells, 501 08190 S ant Cugat del V alles Spain For HP Internal Use Only ©Copy right He wlett-P ackard Compan y 2002 This do cum ent con tains propri etary i nformat ion that i s protected by copyr ight.
1 DesignJet 500 0 and 5500 Series HP Large-Forma t Pri nters Service Manual.
2 HP DesignJ et 5000 and 5500 Series Pr inters Service Manu al Using this Manual Purpose This Service Manual contains information necessary to test, calibra te and servi ce: HP DesignJet 5000 Prin.
Table of Cont ents 3 HP DesignJet 5000 and 550 0 Series Printers Service Manual T able of Contents 1 Troubleshooting 1-1 System Error Codes 2-1 HP Ink Supplies Troubleshooting 3-1 Service Tests and Ut.
Table of C o nten ts 4 HP DesignJ et 5000 and 5500 Series Pr inters Service Manu al.
1-1 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual T r oubleshooting 1 Introdu ction 1-2 Phone Supp ort 1-2 Which Fi rmware V ersio n Rela tes to Whi ch Ink Sy stem 1-2 T roubl eshootin.
Troubleshooting 1-2 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Guide to T r oubleshoot ing the Printer Introdu ction This chapter will guide you through th e relevant steps to take when troubleshooting the Printer .
Troubleshooting 1-3 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Performing a Se rvice T est on a Failed Asse mbly If possible, always perform a Service T est on t he component/ assembly that you are about to replace, just to make sure that is the component/assembly that has failed.
Troubleshooting 1-4 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual T roubleshoot ing Ink Suppli es Err or Code s Chapter 3, HP Ink Supplies T r oubleshooting , contains a l ist of Error Codes that are reported for Ink Supplies i.e. Ink Cartridges, Printheads and Printhead Cleaners.
Troubleshooting 1-5 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual The Print er does not Power ON 1. Check that the Power Cord is conne cted corre ctly to the Printer and to the Powe r Socket. 2. Check tha t the Power Switc h on the BACK of the Printer is in the ON position.
Troubleshooting 1-6 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual ALL the Fr ont-Pan el LEDs ar e Lit but Nothing Else Happens The BootROM DIMM is NOT correctly instal led or is the wro ng type. 1. Power OFF the Printer from the back and disconnect the Powe r Cord.
Troubleshooting 1-7 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual T roubleshoot ing Shutdowns - Use r Message "W arning: Switch Power Off" If a shutdown occurs, you will get the message “W arning: Switch Power Off” followed by: Check Printhead Cleaner Path.
Troubleshooting 1-8 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Check Pape r Path This warning appears w hen ever the friction o n the Paper-Axis is too high: the electrical current needed by the Paper-Axis Motor to move the paper is too high , so before burning th e motor or the Main PCA, this warni ng appears.
Troubleshooting 1-9 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual NOTE Also, after re placing th e Scan-Axis Mo tor , perform the Scan-Axis T est ( Page 4-10 and check that the v alues are within the gi ven limits. If the Prin ter s till fa ils, repla ce the Main PCA Page 8- 81 .
Troubleshooting 1-10 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Problems with V acuum If you have problems loading either Roll or Sheet Media, then there could be a problem with the V acuum Fan or Booster Fan. T o ver ify if there really is a problem with V acuum, try the following: 1.
Troubleshooting 1-11 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Printhead Crashes/Smears on High Density Prints Using Coated M edia High density prints can cause cockle mainly on HP Coated Media.
Troubleshooting 1-12 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Banding at variable extr em e envir onmental conditi ons The Accuracy Calibration has bee n done at normal environmen.
Troubleshooting 1-13 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Hue shift on HP Co lorfast Adhesive V inyl media Under high humidity conditions (approx. >65%) the colors tend to fade over time, parti cularly colors tha t require Magent a.
Troubleshooting 1-14 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Loss of G loss on HP Phot o Im aging Gloss when using the T ake-Up Reel Under high humidity conditions (approx. >70%) the polymer chain in the co ating of this media relaxe s and the drying rate de creases.
Troubleshooting 1-15 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual W rinkles and scratche s (cockle) on HP Coated and Heavyweight Coat ed Media. Images may be damaged if prints are not handled with care, particularly when handling wide plots.
Troubleshooting 1-16 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Drying T ime T oo Long for HP S tudio Canvas Under conditions of high humidity (> 70%) HP St udio Canvas retains a high amount of water and takes too long to dry , also creating problems in using the T ake-Up Reel and Bin.
Troubleshooting 1-17 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 2. The media sensor is defective. T o verify this, remove the media and re-boot the Printer . If the me ssage comes up dur ing initialization, the media sensor is defective.
Troubleshooting 1-18 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual T railing Cable con nection, so just recon nect the T railing C able again to dou ble-check th at the Pr inter now works. If, aft er reconnect ing the cable, the error appe ars again, either the Carr iage PCA or the T railing Ca ble is defec tive.
Troubleshooting 1-19 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Cutter Assembly Pr oblems 1. The Printer does not cut (even when using the Form Feed & Cut option in the Front Panel). In this case it is very likely tha t the cutter is disabled in the EEROM.
Troubleshooting 1-20 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Carriage and Scan-Axis Pr oblems 1. Printhead continuity problem s. When installing the Ink T ubes System, it is possible that the crane (the part of the T ubes Syst em that is connected to the front of the Carriage) is not clipped pr operly .
Troubleshooting 1-21 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Electr onics Pr oblems 1. The Printer hangs with the front panel completely blank and the three Image Quality LED’ s lit. The firmware has a bug that cr eates this situation whenever the Printer is rece iving data from an exte rnal RIP .
Troubleshooting 1-22 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual 3. The Printer is printing slower compared to another HP DesignJet 5000. It is important first to determine whether the differences are during receiving/processing, during printing or once the print is finished.
Troubleshooting 1-23 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 3. The dry time at the end of the print is longer . Normally the Printer uses the temperature and the humidity readi ng from the ISS PCA to c alculate the dry time, whic h is required for the print to dry before being cut.
Troubleshooting 1-24 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual T ypical Failur es After Exchangi ng the Ink T ubes The following table contains typical failures that could appear a.
Troubleshooting 1-25 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Solving Media-H andling Pr oblems NOTE HP Designjet Printer s minimum med ia size is A3 in portrait mode. The Front Pan el Keeps Indicating that Media I s Misaligned or Incorrectly Position ed Roll med ia The roll may be loaded the wrong way .
Troubleshooting 1-26 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual How to Navigate through th e Fron t Panel Menus Shaded boxes always appear in th e front panel.
Troubleshooting 1-27 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Device Setup Menu Device Setup Cutter Lang TUR Installed NO,YES On, Off Reduced Margins On, Off PostScript@, Automatic HP-GL/2 Drying Time Manual Automatic, None 255 ..
Troubleshooting 1-28 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Utilitie s M enu Utilities Replace Ink System Usage No (Continue) , Yes (Replace) Print usage, View usage Track Media.
Troubleshooting 1-29 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Internal RIP Settings Menu Ink Emulation PS scale RGB@ Optimized, Immediately CMYK Off,On Off,On Off,On 100% .
Troubleshooting 1-30 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Queuing and Nes ting Men u Nest Off # .... Nesting Queue mgmt Move to top, Delete Page Copies 99 .
Troubleshooting 1-31 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual HP-GL/2 Settings Menu Define Palette Pen no. 0 … 15 Pen no. 0 … 15 0.
Troubleshooting 1-32 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Page Format Menu Page Format Extrawide Oversize Size Inked Area, Software 1.0X1.4m 42inX59in 44X62in 1.2X1.7m 52X73in 54X76 60X100in Over A2, Over A1 Arch Best ARCH, ARCH A.
Troubleshooting 1-33 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Demos Menu Demos Samples Palette Menu Always Appear Only Appe ar in Full Menu Mode @ PostSc ript Only.
Troubleshooting 1-34 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Media Menu Media Selection Move Media HW Coated (Economy) HW Coated Coated Paper Photo Imaging Gloss Colorfast Vinyl Paper Semi-Gloss Poster Paper Studio Canvas and more.
Troubleshooting 1-35 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Ink Cartridge Menu Replace Ink Cartridge Yes, No HP No. 81 Ink Cartridge Ink Level Capacity Part Number Manufacture Date Light Cyan cart Info Light Magenta cart Info Yellow cart.
Troubleshooting 1-36 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Printhead Menu Recover Printheads Light Cyan Info Light Magenta Info Yellow Info Cyan Info Magenta Info Black Info Pr.
Troubleshooting 1-37 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Servi ce Conf igura tion Print The Service Configuration Print is a useful tool for troubleshooting the Printer . The Service Configuration Print contains the following information about the Printer: General Configuration Printhead Info.
Troubleshooting 1-38 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual 4. Once inside the “Utilities” menu, use the Arrow keys t o scroll to the “T e st prints” menu display and press the Enter key . 5. Use the Arr ow keys to s croll to “Service Config.
Troubleshooting 1-39 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual General Pri nter Inf ormation 1. Interaction between start printing and nesting. Of the four possible combinations between "St art Printing = Optimized or After processing" an d "Nesting = In order or OFF" only two are possible.
Troubleshooting 1-40 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual of the print. Perform a manual r ecovery if t he Printhead status is (XX20) RECOVER/ (XX21) REPLACE. W ith longer plots, average produc tivi ty will increase (i.e. same area is printed in less prints > reduction of servicing at the beginning/end of the print).
2-1 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Err or Codes 2 System Erro r Co des 2-3 Introdu ction 2-3 Continuab le and Non-Con tinuable Erro r Codes 2-4 System Erro r Gro.
System Error Codes 2-2 HP DesignJet 5000 and 5500 Series Printers Service Man ual 0B0001 2 -16 0B0002 2 -16 0B0003 2 -16 0B0004 2 -17 0B0005 2 -17 0B0006 2 -17 0B000X 2-18 0B0010 xx xxxxxx (Non -Conti.
System Error Codes 2-3 HP Desig nJet 500 0 and 5500 Series Pri nters Serv ice Manual System Error Codes Introdu ction NOTE Before tr oubles hooting System Errors, if possible, r epeat the procedure performed wh en the error was reported.
System Error Codes 2-4 HP DesignJet 5000 and 5500 Series Printers Service Man ual If you have an error code which is not documented in this Service Manual or you have an error which you cannot resolve, then report the error to the HP Response Center or the near est HP Support Of fice.
System Error Codes 2-5 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: ffff ff ff xxxxxxxx (Ge neral Firmware Er ror) Prob lem Desc rip tion: Al l ffff fff f er ro r s ar e ge n er a l f i r m wa re e rr o r s.
System Error Codes 2-6 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: ffff ff ff 01dcxxxx Prob lem Desc rip tion: Ther e is a problem with the I/O Card (happens during power-up). Corr ectiv e Action: T r y the followin g: Disconnect the Network Cable and check if the error still appears during power-up.
System Error Codes 2-7 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: ffff ff ff 03450097 Prob lem Desc rip tion: If the W indow is opened during the cutting operation, the Printer hangs and the Carriage suddenly stops.
System Error Codes 2-8 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 010023 ( Non-C ontinuab le) Prob lem Desc rip tion: EER OM T est failure.
System Error Codes 2-9 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 010041 Prob lem Desc rip tion: Error in Scan-axis Encoder quadrature. Corr ectiv e Action: T r y the followin g: Check that the Encoder Strip is NOT broken or damaged.
System Error Codes 2-10 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 010090 ( Contin uable) Prob lem Desc rip tion: Error in Paper -axis Motor Encoder Corr ectiv e Action: T r y the followin g: Check that the Paper-Axis Motor cable is NOT broken or damaged.
System Error Codes 2-11 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 040000 01E603D9 Prob lem Desc rip tion: This is an error that is related to the Parallel Port. It happens n o rmally in New Printers and only o nce (it is unlikely to appear again).
System Error Codes 2-12 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 06030C Prob lem Desc rip tion: Bad Line Sensor . Corr ectiv e Action: T r y the followin g: Replace the Line Sensor Page 8-53 . Replace th e Carriage Assembl y Page 8-46 .
System Error Codes 2-13 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0A0000 Prob lem Desc rip tion: APS Failure. Corr ectiv e Action: T r y the followin g: Check all the cables of the APS and make sure they are correctly connected and are NOT dama ged.
System Error Codes 2-14 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0A0030 Prob lem Desc rip tion: Pr oblem in Depressurizing Air System. Corr ectiv e Action: T r y the followin g: Check the APS for any signs of Ink.
System Error Codes 2-15 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0A0050 (Non-Continuable) Prob lem Desc rip tion: The Printer has de tected a leak in the T ubes System - Should ONL Y appear in printers with the Ink Leak Detector installed.
System Error Codes 2-16 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0B0001 Prob lem Desc rip tion: Bad Humidity Read Corr ectiv e Action: T r y the followin g: Replace t he ISS PC A Page 8-91 Replace t he Main PCA Page 8-81 .
System Error Codes 2-17 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0B0004 Prob lem Desc rip tion: APS Failure. Corr ectiv e Action: T r y the followin g: Check that the cable from the Ink Supply Station (ISS ) PCA to the Ink Supply Station is correctly connected.
System Error Codes 2-18 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0B000X Prob lem Desc rip tion: Unable to de tect Fan (X = 7 - V acuum, 8 - Cooling, 9 - Aerosol). Corr ectiv e Action: T r y the followin g: Make sure that the Fan is connected correc tly to the Main PCA.
System Error Codes 2-19 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0B000B Prob lem Desc rip tion: APS Failure. Corr ectiv e Action: T r y the followin g: Check that the cable from the Ink Supply Station (ISS ) PCA to the Ink Supply Station is correctly connected.
System Error Codes 2-20 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0B000F ( Cont inuabl e ) (Only applicable to DesignJet 5500 Series) Prob lem Desc rip tion: Unable to detect the Heat er - If this error appears, all settings relate d to the heater will disappear from the front Panel.
System Error Codes 2-21 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0C0032 ( Contin uable) Prob lem Desc rip tion: Drop Detector not calibrated or the calibration settings h ave been lost.
System Error Codes 2-22 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0C00FF Prob lem Desc rip tion: Pr int Mask could not be generate d.
System Error Codes 2-23 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0D0000 ( Contin uable) Prob lem Desc rip tion: No Media Profiles A vailable. Corr ectiv e Action: Download a media profile for the ink type being used.
System Error Codes 2-24 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: 0D0005 03180382 (Non-Continuable) Prob lem Desc rip tion: After cutting the media, the Printer cannot deactivate the Cutter .
System Error Codes 2-25 HP DesignJ et 5000 an d 5500 S eries Printer s Service Manu al System Error: 0F0200 01E603d2 Prob lem Desc rip tion: This is an error that is related to the Parallel Port. It happens n o rmally in New Printers and only o nce (it is unlikely to appear again).
System Error Codes 2-26 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual System Error: e50000 Prob lem Desc rip tion: This is an error that is related to the Hard Disk Drive, either the connections are bad or that the Hard Disk Drive or the Main PCA are defective.
3-1 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual HP Ink Supplies T r oubleshooting 3 What are HP In k Supplie s? 3-2 Ink Cartridg e s 3-2 Printheads and Printhead Cleane rs 3-2 Iden t.
HP Ink Supplies Troubleshooting 3-2 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual What ar e HP Ink Supplies ? For each of th e six colors used in th e Printer , ther e are three s eparate components. The Printhead and the Printhead Cleaner are supplied together , the I nk Cartridge is supplied separately .
HP Ink Supplies Troubleshooting 3-3 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Identifyi ng the Components The following illustration will help you i dentify the components of the HP Ink Supplies.
HP Ink Supplies Troubleshooting 3-4 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual A void unnecessary re moval of the Ink Cartridges and Printheads. When turning off the Printer always use the soft-power Off button on the Front Panel.
HP Ink Supplies Troubleshooting 3-5 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Priming a Brand New Ink System When the customer first receives the Printer , it is supplied with a set of six Setup Printhea ds pre-installed in th e Carriage Assembly .
HP Ink Supplies Troubleshooting 3-6 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual The Fr on t Panel Display The front panel display has a dedicated area to report the status of your HP Ink supplies. S tatus messa ges consist of a code and an action message Ink displays information on the Ink Cartridges.
HP Ink Supplies Troubleshooting 3-7 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Obtaini ng Ink Cartridge Informat ion 1. T o get information on the Ink Car tridges press the To p key on the front panel to go to the main menu.
HP Ink Supplies Troubleshooting 3-8 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. The front panel displays information on the selected Ink Cartridge. The information supplied is: The make of the Ink Car trid ge ( No.81 for Dy e and No.
HP Ink Supplies Troubleshooting 3-9 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 3. Press n or p key until the front panel hi ghlights “Printhead info”. Press Enter to view the Printhea ds information . 4. Press the n or p key until the front panel highlights the color that you want to see information on.
HP Ink Supplies Troubleshooting 3-10 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual S tatus Codes and Messages NOTE Most pr oble ms with Ink Su pplies wil l be solved by the user simply following the instructions in the action message.
HP Ink Supplies Troubleshooting 3-11 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual S tatus Message s These messages provide only an action message for the user to perform. For information on ac cessing detailed information on consumables refer to 3-7, Obtaining Ink Cartridge Information and 3-8, Obtaining Printhead Information .
HP Ink Supplies Troubleshooting 3-12 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Err or S tat us Messages Error status messages consist of the HP S tatus Code and the action message. The following tables gr oup error messages acc ording to the consumable, the ac tion message (i.
HP Ink Supplies Troubleshooting 3-13 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Printhead Err ors NOTE If you think your Printer is re questing you to replace your Printhe ads to o frequently you can check Printhe ad nozz le sta tus by printing the Diagnostic Print Refer to 6, Print Quality .
HP Ink Supplies Troubleshooting 3-14 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Printhea d Informa tion St a t u s Numbers Error Description Proc edure XX02 Reseat XX06 Reseat XX08 Reseat Continuity problem be tween the Printhead and the Carriag e Ass embly .
HP Ink Supplies Troubleshooting 3-15 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Printhea d Recovery Procedure The Printer regularly performs a series of controls on the he alth of the Printhea ds and when they st art to degrade the Printer will prompt the user to recover the Printhead [ (X X20)Recover ].
HP Ink Supplies Troubleshooting 3-16 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Ink Cartridge Err ors NOTE When r eplacing Ink Cartridges: Use the Replace item in the In k Cartrid ges me nu. This will release all air from the Ink Cartridge and avoid pr oblems in its removal.
HP Ink Supplies Troubleshooting 3-17 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual S tatus Numbers Error Description Procedur e Ink Cartridge Information XX0 3 Re pl ace The Ink Cartr idge has a leak which prevents the ink pumpin g to the Printer .
HP Ink Supplies Troubleshooting 3-18 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Printhead Cleaner Err o rs (First Digit = A, B or * ) NOTE When re placing Printhead Cleaners: Ensur e that you have the correct Printhead Cleaner .
HP Ink Supplies Troubleshooting 3-19 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Replace Message "xx16 Replace " for ALL Printheads During Replacement During Printhead replacement, the message "xx16 Replace" can appear for ALL the Printheads due to a firmware bug.
HP Ink Supplies Troubleshooting 3-20 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Risks with the Ink Cartridg e Delivering T oo Muc h Ink Meeting Point Refills: If the customer refi lls within the ink meeting point zone, then the ink cartridge will operate “normally .
HP Ink Supplies Troubleshooting 3-21 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Non-HP Hard war e Det ected in the In k Deliv ery Sy stem The following information explains the front panel message flow: Error Message XX08 Unknown Description Use genuine HP components f or excellent image qua lity from your printer .
HP Ink Supplies Troubleshooting 3-22 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Risks with Using Non-HP Hardware The risks in using non-hp hardware refill systems are: Printhead dry fire. Probable empty ink tubes. These issues can be caused by: Cartridge not refilled to 100%.
HP Ink Supplies Troubleshooting 3-23 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual ILS Out of Contr ol W arranty S tatement Printhead and cl eaner wa rranty: Un t il the “end of warranty” date printed on the product is reached, or 700 cc of HP ink is delivered through the printhead, whichever occu rs first.
HP Ink Supplies Troubleshooting 3-24 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual.
4-1 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Service T ests and Utilities 4 Introdu ction 4- 2 Diagnostics - Self T est 4-2 The Printer hangs and no thing el se happens 4- 3 Error.
Service Tests and Utilities 4-2 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Intr oduction This chapter explains how to use the built-in Service T ests and Service Utiliti es and what to do if any of t he Service T ests fail.
Service Tests and Utilities 4-3 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual W ARNING Only r eplace one component at a time and check i f the err or has gone before r eplacing another component.
Service Tests and Utilities 4-4 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Spin ning up d isk Boot Fai led:1 f500XX This is an error related to the Hard Di sk Drive, eithe r the connect ions are ba d or the Hard Disk Drive or the Main PCA are defective.
Service Tests and Utilities 4-5 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Service T ests (Diagnostics) The following is a list of all inte rnal Service T e sts availa ble in the Printer . Instructions for entering the Serv ice T ests menu are given on Page 4-6 .
Service Tests and Utilities 4-6 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Entering the Ser vice T ests Menu 1. Once the message "Ready" is displayed on the front-panel, scroll to the "Printer Setup Options" icon and press the Enter key .
Service Tests and Utilities 4-7 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual For Call Agents requ esting th e User to access a limit ed number of Service T ests a Once inside the &quo.
Service Tests and Utilities 4-8 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual If your Firmware does not support Service T ests, the following message is displayed. Y ou should press Ente r to exit. If you need the Service T ests, download the la test Firmware and repe at the whole procedure to enter the Ser vice T e sts menu.
Service Tests and Utilities 4-9 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Scan Axis T est The purpose of this test is to verify: Carriage movement al ong the Printer axis.
Service Tests and Utilities 4-10 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual NOTE Report the values to the nearest HP Response Center or HP Suppor t Office to deter mine whether values ar e within the accepted range. When re porting the values, have the following information r eady: Model and Serial Nu mber of the Printer .
Service Tests and Utilities 4-11 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Media Axis T est The purpose of this test is to verify: Overdrive Roller movement. Paper -Axis motor . This test measures the current required to move the Media Axis parts in order to verify if parts are moving freely or not.
Service Tests and Utilities 4-12 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual NOTE Report the values to the nearest HP Response Center or HP Suppor t Office to deter mine whether values ar e within the accepted range. When re porting the values, have the following information r eady: Model and Serial Nu mber of the Printer .
Service Tests and Utilities 4-13 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Service Uti lities The following is a list of al l intern al Servi ce Utilities available in the Printers. Instructions for ent ering the Service Uti lities menu ar e given on Page 4-14 .
Service Tests and Utilities 4-14 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Entering the Ser vice Uti lities Men u 1. Once the message "Ready" is displayed on the front-panel, scroll to the "Printer Setup Options" icon and press the Enter key .
Service Tests and Utilities 4-15 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual For Call Agents requ esting th e User to access a limit ed number of Service Util ities a Once inside the "Printer Setup Options" menu and the "Device setup" menu is highlighted, press the following key combination.
Service Tests and Utilities 4-16 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual NOTE If the Prin ter is not used for 3 minutes, the Printer exits th e Service Utilitie s Menu and you mu st rep eat the above steps to enter Service Utilities again.
Service Tests and Utilities 4-17 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual T urn DRI VE ROLLER The purpose of this Servi ce Utility is to rotate the Overdrive, Drive Roller and Roller Mark in order to clean them. NOTE Remove the media before performing this operation.
Service Tests and Utilities 4-18 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Prime TUBES The purpose of this Servi ce Utility is to prime t he T ubes when the tubes are NOT new and they need to be reprim ed or automatic priming was not completed.
Service Tests and Utilities 4-19 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 4. The following message will be disp layed on the front panel while the printer verifies the Ink Cartridges:. 5. When the following message is displayed, lift the W i ndow and remove ALL the Printheads from the Carriage.
Service Tests and Utilities 4-20 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual 8. The Printer will then begin to prime the T ubes S ystem.
Service Tests and Utilities 4-21 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 12. If media is not loaded, the following message appears on the front panel and you must load media into the Printer .
Service Tests and Utilities 4-22 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Altitude Setu p This Service Utility allows the operating altitude t o be set for the Printer for particular opera ti ng conditions when media load problems occur .
Service Tests and Utilities 4-23 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual EEROM Setup NOTE This test is only necessary in a situation wher e you have NOT been able to p erform the E EROM backup test and you have lost all the EEROM pa rameters.
Service Tests and Utilities 4-24 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual If you want to set the Model Number a If you want to set the Model Number select "1.4.1 Set Model Number" and press the Enter key to access the list of possible Model Numbers for the Printer .
Service Tests and Utilities 4-25 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual If you want to set the Ser ial Number NOTE The Se rial Number in the Cur r ent field is only disp layed if i t is encoded in the E EROM. a Select "1.4.
Service Tests and Utilities 4-26 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual If you want to set the Jap anese Fonts NOTE If the customer is not using any internal Japanese PS Fonts, then this Ser vice Util ity is not necessary .
Service Tests and Utilities 4-27 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual b If you select Ye s the message below wi ll be displayed. Press Enter to comple te loading and return to the EEROM Setup utilit y or press Bac k to return to the previous message.
Service Tests and Utilities 4-28 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Reset Life Counters The purpose of this Servi ce Utili ty is to reset the preventive maintenance counters when par ts have been replaced.
Service Tests and Utilities 4-29 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual The front panel message displays the following information: Color (Printhead Insertions only); the Printhead colo r for which the counter is being reset.
Service Tests and Utilities 4-30 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Backup EEROM This Service Utility is used to res tore the contents of the EER OM when a service enginee r has replaced the Main PCA or the Hard Disk Drive.
Service Tests and Utilities 4-31 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 3. If you select "Main PCA" a message confirming the selection is displayed. Press Ente r to con firm and exit this utilit y or press Back to cance l.
Service Tests and Utilities 4-32 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Image Qu alit y W arning This Service Utility is used to turn the Im age Quality W arning On or Of f.
Service Tests and Utilities 4-33 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Diagnostic Print This Service Utility al lows you to pr int a Diagnostic print that will help you to troubleshoot image quality problems and verify printhead nozzl e status.
Service Tests and Utilities 4-34 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Sleep Mode (DesignJ et 5500 Series Only) The purpose of this Servi ce Utility is to disable t he Sleep Mode so that the P rinter is never switched OFF automaticall y if not used after a certain period.
5-1 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Service Calibrations 5 Servic e Calibrat ions 5- 3 Entering the Se rvice Cal ibration s Menu 5-4 1.
Service Calibrations 5-2 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Intr oduction The Printer has seve ral calibrati on procedures that must be performed under cer tain conditions. Refer to the table on the next page to determine when calibrations are require d.
Service Calibrations 5-3 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Service Calibrations The following is a list of all inte rnal Service Ca librations avail able in the Printers. Instructions for entering the Service Calibrations menu are given on Page 5-4 .
Service Calibrations 5-4 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Entering the Ser vice Cali brations Menu 1. Once the message "Ready" is displayed on t he front-panel, scroll to "Printer Setup Options" icon and press the Enter key .
Service Calibrations 5-5 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual For Call Agents requ esting th e User to access a limit ed number of Service Cal ibrations a Once inside the &quo.
Service Calibrations 5-6 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual NOTE If the Prin ter is not used for 3 minu tes, the Printer exi ts out of the Servic e Calibr ations Menu and you must repeat the above steps to enter Service Calibrations again.
Service Calibrations 5-7 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 1. Scan-Axis Calibrat ion The purpose of this Service Calibrati on is to calibrate the Printhead in relation to the me dia and the Pla ten Assembly . This Calibration also allows you to calibrate the Li ne Sensor and define the Line Sensor ID.
Service Calibrations 5-8 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual If the Media loaded is not the right size, the following message is displayed. Press Enter to exit. Load the correct media and r epeat the procedure. 2. If the correct media is loaded, the following message is displayed.
Service Calibrations 5-9 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 4. When you have inserted the Line Sensor Id. the message below is displayed. Press Enter to confirm the number and continue the calibration or Ba ck to modify the number .
Service Calibrations 5-10 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 7. The Printer then perform s the Printhead to media spacing calibration and displays the following message: During this stage the Printer will pri nt the fol lowing pattern.
Service Calibrations 5-11 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 2. Service S tation Calibration The purpose of this Servi ce Calibration is to calibrate the Service St ation in relation to the Carriage Assembly . The Service Station Calibration performs the following calibrations: Line Sensor to Black Pen.
Service Calibrations 5-12 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 2. If the correct media is loaded, the following message is displayed.
Service Calibrations 5-13 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 5. On completing the Drop Detector calibration, the following message is displayed: 6. On completing the calibration successfully , the following message is displayed.
Service Calibrations 5-14 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 3. Accuracy Calibration The purpose of this Accuracy Calibration is to set the nominal advance of the media, changing the factory default values stored on the EEROM.
Service Calibrations 5-15 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 3. If media is not loaded, the following message appears on the front panel and you must load media into the Printer . Pre ss the Load/ Unload Media button (see the User ’ s Guide for detailed information on loading media).
Service Calibrations 5-16 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 6. The Printer will unload the media a nd request you to remove it from the Printer . Press Enter to continue. 7. The following message is displayed. Press Load/Unload Medi a to start the load procedure for the printed sheet.
Service Calibrations 5-17 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual If the Calibration fails the following message is displayed. Press Enter to continue.
Service Calibrations 5-18 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Carriage Height Calibration The purpose of this Service Calibration is to adjust the distance between the Carriage Assembly and the Center Platen. This calibration is necessary in order to preve nt problems like Printhead crashes.
Service Calibrations 5-19 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual NOTE During the Carr iage Height Cal ibration procedure the Carriage Assembly has to be moved along the length of t he Printer f or corr ect calib ration .
Service Calibrations 5-20 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 5. Insert the Carriage Height T ool into the black Printhead slot.
Service Calibrations 5-21 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 7. Loosen the two T10 screws at the back of the Carriage Assembly .
Service Calibrations 5-22 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 9. Lower the C arriage Assembly slightly , by turning the T9 screw shown below anti-clockwise and then check f or a scraping sound again as shown previously in step 7.
Service Calibrations 5-23 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 11 . Raise the Ca rriage Assembly slightly , by turning the T9 screw (shown below) clockwise .
Service Calibrations 5-24 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 13. When the s craping has been el iminated it i s important to leav e the Carria ge Assembly as close a s possi.
Service Calibrations 5-25 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 15. When the complete length of the Printer is calibrated (c lear of any scraping sound), tighten the two T10 screws at the back of the Carriage Assembly to secure the c urrent position.
Service Calibrations 5-26 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibration Err or Codes Introdu ction NOTE Calibration Error Codes are continuable, wh ich means you can press Enter on the Front Panel to continue working with the Printer .
Service Calibrations 5-27 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 0000 NOTE This code is not an err or . See the other codes reported.
Service Calibrations 5-28 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 0020 Prob lem Desc rip tion: Line Sensor er ror . Corr ectiv e Action: Check the me dia used for the Ca libration is WHITE. Replace the Lens Cover Assembly Page 9-5 .
Service Calibrations 5-29 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 1002 (User) Prob lem Desc rip tion: The Line Sensor pa ttern is not printed.
Service Calibrations 5-30 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 1005 (User) Prob lem Desc rip tion: Pa per Axis Er ror . Corr ectiv e Action: T r y the followin g: Perform Printhead Recovery ( Page 6-15 ).
Service Calibrations 5-31 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 1042 (User) Prob lem Desc rip tion: Scan-A xis Alignment Error in "slow" speed section in Light Cyan and Light Magenta Pattern. Corr ectiv e Action: T r y the followin g: Perform Printhead Recovery ( Page 6-15 ).
Service Calibrations 5-32 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 2004 (User) Prob lem Desc rip tion: Media Profile Er ror . Corr ectiv e Action: T r y the followin g: Download a Media Profile for the current medium.
Service Calibrations 5-33 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 2101 (through to 2607) (User) Prob lem Desc rip tion: Firmwa re Error . Corr ectiv e Action: T r y the followin g: Repeat the Closed Loop Color calibration ( See the User ’ s Guide).
Service Calibrations 5-34 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 3130 Prob lem Desc rip tion: Firmwa re Error . Corr ectiv e Action: T r y the followin g: Power the Printer OFF and ON again using the Power Switch at the back of the Printer to rese t the memory .
Service Calibrations 5-35 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 4003 (Service) Prob lem Desc rip tion: Line De tection Error . Corr ectiv e Action: T r y the followin g: Check that the Lens Cover is clean.
Service Calibrations 5-36 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 5002 (Service) Prob lem Desc rip tion: Bla ck Printhead failure. Corr ectiv e Action: T r y the followin g: Perform Recovery for Black Printhead Page 6-15 .
Service Calibrations 5-37 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 5010 (Service) Prob lem Desc rip tion: T oo many Black Printhead nozzles not working. Corr ectiv e Action: T r y the followin g: Recover the Black Printhead ( Page 6-15 ) and if the problem persists replace the Black Printhead.
Service Calibrations 5-38 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 6000 (Service) NOTE This code is not an err or . See the other codes reported. Calibrat ion Err or: 6001 (Service) Prob lem Desc rip tion: Drop De tector not working.
Service Calibrations 5-39 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 6006 (Service) Prob lem Desc rip tion: Drop De tector failed to reach position for calibration. Corr ectiv e Action: Refer to Error Code 6005.
Service Calibrations 5-40 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Calibrat ion Err or: 6012 (Service) Prob lem Desc rip tion: Calibration failed for Ligh t Cyan Printhead. Corr ectiv e Action: Recover the Light Cyan Printhead Page 6-15 .
Service Calibrations 5-41 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Calibrat ion Err or: 6018 (Service) Prob lem Desc rip tion: Calibration position out of range for Light Cyan Printhead. Corr ectiv e Action: Replace the Drop Detector A ssembly Page 8-72 .
Service Calibrations 5-42 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual User Calibrations The following is a list of internal User Calibrations available in the Print ers. 1. Printhead Alignment Page 5-43 2. Close-Loop-Color Calibration Page 5-43 3.
Service Calibrations 5-43 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Printhead Alignment The printer will normally perfor m an alignmen t automatic ally whenever any printhead is replace d.
Service Calibrations 5-44 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Banding Calib ration The banding calibra tion is intended t o eliminate the problem of banding, by optimizing the media a dvance settings to suit the printing material, and the environmental conditions such as humidity and temperature.
Service Calibrations 5-45 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Accuracy Calibration The printer is cali brate d a t the factory to e nsure that it opera tes wit h the greatest ac curacy in norma l environmental conditions.
Service Calibrations 5-46 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual.
6-1 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Print Quality 6 Print Qu ality 6 -2 Print Quali ty T ro ubleshooting Checklist 6 -2 How to Use the D iagno stic Print 6-4 What is the Di a gnostic Print? 6-4 Considerat ions for Printi ng the Dia gnostic Pr int.
Print Qual ity 6-2 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Print Quality Print Quality T roubles hooting Checklist When faced with a Print Quality problem, use the following che.
Print Qual ity 6-3 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 6 Driver print quality configuration: T o cla rify if the reason of the pr obl em is related with the print m ode defined with the Non-HP Driver try the following: Print the same sample using the Non-HP driver and their normal media.
Print Qual ity 6-4 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual How to Use th e Diagnos tic Pri nt What is the Diagnos tic Print? The Printer contains internal Dia gnostic Prints to help you diagnose the possible source of some print quality defects.
Print Qual ity 6-5 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Printing the Diagnosti c Print 1 Once the message “Rea dy” is displa yed on the Front Panel, scroll to the “Printer Setup Options” icon and press the Enter key .
Print Qual ity 6-6 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual For Call Agents r equesting the User to print the Service Di agnostic print a Once inside the “Printer Setup Options” menu and the “Device setup” menu is highlighted, pre ss the followin g key combination .
Print Qual ity 6-7 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual NOTE For Firmware V ersion A.02.xx in the 5000 Series and on the 5500 Series, the Printer DOES NOT print the complete Diagn ostic Print. Instead you must select wh ich part of the Diagnostic Print that you need.
Print Qual ity 6-8 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Overal l Pri nt Qual ity T est - Page 1 This test pattern checks for banding in the print mode and media that is being used. What is Ban ding? Banding is when you see repetiti ve horizontal bands within the printed image (these may appear as light or dark bands).
Print Qual ity 6-9 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual In the following exam ple, there is a prob lem in the Magenta Printhead. There will be clear repetitive bands (perhaps white) in the magenta column. NOTE The Print er has automatic procedur es to hide m any Printhead defects.
Print Qual ity 6-10 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Banding in all of the colors NOTE In high qual ity modes media advance problems may not appear as lines of bandi ng, they may ap pear grain y inste ad. The b anding or grainin ess will appear i n all the color s.
Print Qual ity 6-11 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Color Alignment Print T est - Page 2 This part of the Diagnostic Print T est is designed to check the color alignment. It produces five crosses: one for e ach color compared to magenta.
Print Qual ity 6-12 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Bidir ectional Alignment - Page 3 If a Printer has Bidirectional alignment problems, lines are not straight. The pattern shown below is designed to highlight t his kind of problem.
Print Qual ity 6-13 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual V ertical Line S traightness - Page 4 If a Printer has V ertical Line Straightness problems, lines are not straight. The pattern seen below is designed to highlight this kind of problem.
Print Qual ity 6-14 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Nozzle Print T est - Page 5 NOTE If your Printer has nozzle defe cts, it does not mean that you will not get p erfect p rint quality results. The Pr inter has autom atic pr ocedur es to hide ma ny nozzle defec ts.
Print Qual ity 6-15 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual How to fix the Nozzle Defects NOTE The Prin ter will auto matically request you to r e cover Printheads with a number of defective nozzles that may affect print quality , or repl ace them if the Printhead defect cannot be recovered.
Print Qual ity 6-16 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual No Printing Defects Fou nd in the Diagnosti c Print If all the test patterns from the Diagnostic Print are corre ct a.
Print Qual ity 6-17 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual If the problem persists check the lens and if it is dirty replace the Lens Cover Assembly ( Page 9-5 and repeat the ca librations. Perform the Printhead Alignment Page 5-43 .
Print Qual ity 6-18 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Color Accurac y Configurat ion The configurations of the Printer , the driver , and the softwa re RIPs define how ink is applied to each type of media . Use the information in the following table to configure the Printer and software for best color accur acy.
Print Qual ity 6-19 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual length by severa l centimeters . Depending on the type of problem, the troubleshooting sequence is different.
Print Qual ity 6-20 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual 3 If Heavy Coated media is being used, use the Front Panel to select Heavy Coated Economy with Normal paper margins. Other alternatives are either to add a 2.5 cm margin at the beginning of the print or switch to any other type of media.
Print Qual ity 6-21 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Warped Lines on Media The media itself may be warped. T his can happen if it has been used or stored in an extreme environment.
Print Qual ity 6-22 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Using the Color Print Objective an d Descrip tion The objective of the Color Print is to determine whether the printer hardware has any color reproduct ion pro blems. Be fore start ing, load a roll of HP Hi gh-Gloss Photo Paper or HP Heavyweigh t Coat ed Paper .
Print Qual ity 6-23 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Bear in mind that the transition could happen anywhere along the line. T r ust your perception! How to In terpr et the Result If you get a number in the range 4.5 to 9.5, your printer is with in the expected color reproduction a ccuracy .
Print Qual ity 6-24 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Enrichment I ssue Issues Description There can be some li ght color ar ea fills that have two dif ferent (but related.
Print Qual ity 6-25 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual See the f ollowing i mage: Cause: Before going to the root cause, we have to understand two main concepts of the inkjet technology: 1 The dye ink is made by a liquid and pigments (which, in fact, delivers the color to t he ink).
Print Qual ity 6-26 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual evaporates partially , which leaves the ink on the nozz le with more pigments. Therefore, the initial dr ops ejected fr om those nozzles will be darker (they have more pigment) than the f ollowing ones.
Print Qual ity 6-27 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual W orkar ounds This image quality problem i s a product limitation. S o, it has NO solution. Anyway , due to the limited cases wher e the problem could appear , lar ge amounts of comp laints are not expected.
Print Qual ity 6-28 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual Y ou will see that r eplacing any printer’ s hardwar e part can not solve these problems .
Print Qual ity 6-29 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual Given that the DesignJet 5X00 series printer is a production speed printer and customer usage was expected to be a t high volume; aerosol affects were a n expected occurrenc e that customers would see.
Print Qual ity 6-30 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual 2 Presence of marks on the front side of the media. The following figure shows the typical marks on the front side of the printout due to aerosol: So, as you have seen, we can have marks ca used by the ink accumulation on: The center platen (a nd overdrive).
Print Qual ity 6-31 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual The HP DesignJe t 5X00 series is al re ady op timiz e d t o m inimi ze t he static build up within the printer , i.
Print Qual ity 6-32 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual 2 Presence of ink smears or even drops on the printout. See the f ollowing imag e to see an example .
Print Qual ity 6-33 HP DesignJ et 5000 and 5500 Se ries Pri nters Servi ce Manual 3 Ink stains on the media after changing/reseating the printheads NOTE This is a secondary effect of the ink accumulation. See the f ollowing imag e to for an exa mple. Ink accumulation at the botto m of the Carriage Assembly .
Print Qual ity 6-34 HP Desig nJet 500 0 and 5500 Se ries Prin ters Serv ice Manual S tatic: Solutions and W orkar ounds The following options resolve the issue: Use HP DesignJet 5X00 Series approv.
7-1 HP DesignJet 5000 and 550 0 Series Printers Service Manual Parts and Diagrams 7 Printer S upport 7-2 Bin and T ake-Up Reel 7- 4 Right Hand C over 7-6 Left Hand C over and Rear Door 7-8 T op and Ba.
Parts and Diagrams 7-2 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Printer Sup port Printer Suppor t Reference on Drawing HP Part Number Quantity Description/Comments DJ 5000 Series D.
Parts and Diagrams 7-3 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 3: Printer Support 1 4 1 2 2 3.
Parts and Diagrams 7-4 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Bin and T ake-U p Reel Bin an d T ake-Up Reel Reference on Drawing HP Part Number Quantity Description/Comments DJ 5.
Parts and Diagrams 7-5 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 4: Bin and T ake-Up Reel 1 8 3 4 5 6 7 9 2 Bin Su ppor t.
Parts and Diagrams 7-6 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Right Hand Cover Right Hand Cover Reference on Drawing HP Part Number Quanti ty Description/ Comments DJ 5000 Series.
Parts and Diagrams 7-7 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 5: Right Hand Cover 4 7 8 1 5 2 6 3 2 9.
Parts and Diagrams 7-8 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Left Hand Cover and Rear Door Left Hand Cover and Rear Door Reference on Drawing HP Part Number Quantity Descri ptio.
Parts and Diagrams 7-9 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 6: Left Hand Cover and Rear Door 4 5 6 2 2 1 8 2 3 9 7 11 10 12.
Parts and Diagrams 7-10 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual T op and Back Co ve r s T op and Back Covers Reference on Drawing HP Part Number Qu anti ty Descri ption/ Comme nts.
Parts and Diagrams 7-11 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 7: T op and Back Covers 1 2 4 3.
Parts and Diagrams 7-12 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Service S tation Servi ce S tat ion Ref er en ce on Drawing HP Part Number Quantity Descrip tion/Comm ents DJ 5000 .
Parts and Diagrams 7-13 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 8: Service S tation 4 5 2 1 3 2.
Parts and Diagrams 7-14 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual V acuum Fan V acuum Fan Reference on Drawing HP Part Nu mber Qu antity Description/Comm ents DJ 5000 Series D J 550.
Parts and Diagrams 7-15 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 9: V acuum Fan 1 2.
Parts and Diagrams 7-16 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Booster Fan and Media Sensor Booster Fan and Media Sensor Reference on Drawing HP Part Num ber Quanti ty Desc ripti.
Parts and Diagrams 7-17 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 10: Booster Fan and Media Sensor 2 3 1.
Parts and Diagrams 7-18 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Paper -Axis Motor Paper -Axis Motor Reference on Drawing HP Part Number Quant ity Descript ion/Com ments DJ 5000 Se.
Parts and Diagrams 7-19 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 1 1: Paper -Axis Motor 2 3 1.
Parts and Diagrams 7-20 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Scan-Axis Motor Scan-Axis Motor Reference on Drawing HP Part Numb er Quantity Description/Comm ents DJ 5000 Serie s.
Parts and Diagrams 7-21 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 12: Scan-Axis Motor 2 1.
Parts and Diagrams 7-22 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual ISS and APS A ss em bly ISS and AP S Assembly Reference on Drawing HP Part Number Quantity Description /Comments DJ.
Parts and Diagrams 7-23 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 13: ISS and APS Assembly 2 1.
Parts and Diagrams 7-24 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Ink T ubes System Ink T ubes System Reference on Drawing HP Part Number Quant ity Desc ript ion /Comm ent s DJ 5000.
Parts and Diagrams 7-25 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 14: Ink T ubes System 2 1.
Parts and Diagrams 7-26 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Boot ROM DIMM, DRAM Memory an d Covers Boot ROM DIMM, DRAM Me mory and Covers Reference on Drawing HP Part Numb er .
Parts and Diagrams 7-27 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 15: BootROM, Memory and Covers 4 6 5 2 1 3.
Parts and Diagrams 7-28 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Rear Electr onics Access Covers Rear Electronics Access Covers Reference on Drawing HP Part Number Quant ity Descri.
Parts and Diagrams 7-29 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 16: Rear Electron ics Access Covers 1 2 3 4 6 5 7 8.
Parts and Diagrams 7-30 HP Design Jet 5000 and 55 00 Series P rinters S ervice Manual Hard Disk Drive and Cover Hard Disk Drive and Cover Reference on Drawing HP Par t Number Qua nti ty Description/ Comments DJ 5000 Serie s DJ 5500 Series 1 C6 091-60255 - 1 Ha rd Disk Drive PS A.
Parts and Diagrams 7-31 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 17: Hard Disk Drive and Cover 1 3 2.
Parts and Diagrams 7-32 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual ISS PC A and Mai n PC A ISS PCA and Main PCA Reference on Drawing HP Par t Number Quantity Description/Comme nts DJ.
Parts and Diagrams 7-33 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 18: ISS PCA and Main PCA 3 4 2 1 2 5.
Parts and Diagrams 7-34 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Power Supp ly Unit Power Suppl y Unit Reference on Drawing HP Part Number Quantity Desc ription/ Comments DJ 5000 S.
Parts and Diagrams 7-35 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 19: Power Supply Unit 5 1 2 6 3 4.
Parts and Diagrams 7-36 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Carriage Assembly Carriage Assembly Ref er en ce on Drawing HP Part Num ber Quantity Description/ Comments DJ 5000 .
Parts and Diagrams 7-37 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 20: Carriage Assembly 5 3 2 1 4.
Parts and Diagrams 7-38 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual T ensioner Ass emb ly and Enc oder S trip T ensioner Asse mbly and E ncoder S trip Reference on Drawing HP Part Num.
Parts and Diagrams 7-39 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 21: T ensioner Assembly and Encoder S trip 2 4 5 3 1.
Parts and Diagrams 7-40 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Platen Assemblies - DesignJet 5000 Series Platen Assemblies - DesignJet 5000 Series Reference on Drawing HP Part Nu.
Parts and Diagrams 7-41 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 22: Platen Assemblies - DesignJet 5000 Series 1 3 4 5000 Series Only 2.
Parts and Diagrams 7-42 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Platen Assemblies - DesignJet 5500 Series Platen Assemblies - DesignJet 5500 Series Reference on Drawing HP Part Nu.
Parts and Diagrams 7-43 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 23: Platen Assemblies - DesignJet 5500 Series 1 3 4 2 5500 Series Only.
Parts and Diagrams 7-44 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Pinch-Whee ls Asse mbly and Lever Pinch-Wheels Assembly and L ever Reference on Drawing HP Part Number Quantity Des.
Parts and Diagrams 7-45 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 24: P inch-Wheel s Assembly and Lever 5 3 7 6 4 2 1.
Parts and Diagrams 7-46 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Center Guide, Deflecto rs an d Entry Roller - DesignJet 5000 Series Center Guide, Deflectors and En try Roller - De.
Parts and Diagrams 7-47 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 25: Center Guide, Deflectors and Entry Roller - DesignJet 5000 Series 2 1 7 2 3 6 4 5 5000 Series Only.
Parts and Diagrams 7-48 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Center Guide and Entry Ro ller - DesignJet 5500 Series Center Guide and Entry Roller - DesignJet 5500 Series Refere.
Parts and Diagrams 7-49 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 26: Center Guide and Entry Roller - DesignJet 5500 Series 4 5 3 2 2 1 5000 Series Only.
Parts and Diagrams 7-50 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual T ubes Guide Assem blies T ubes Guide Assemblies Reference on Drawing HP Part Numb er Qu anti ty Description/ Comme.
Parts and Diagrams 7-51 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 27: T ubes Guide Assemblies 3 4 5 6 7 1 2.
Parts and Diagrams 7-52 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual EMC Covers EMC Covers Reference on Drawing HP Part Num ber Qua nti ty Descri ption/ Comm ents DJ 5000 Serie s DJ 55.
Parts and Diagrams 7-53 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figure 28: EMC Covers 1 2 1 1 3.
Parts and Diagrams 7-54 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Spindle and Hub Spindl e and Hu b Reference on Drawing HP Par t Number Quantity Desc ription/Comme nts DJ 5000 Seri.
Parts and Diagrams 7-55 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 29: Spind le and Hub 1 3 2.
Parts and Diagrams 7-56 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Rollfeed Brakes Rollfeed Brake s Reference on Drawing HP Par t Number Quantity Desc ription/Comme nts DJ 5000 Serie.
Parts and Diagrams 7-57 HP DesignJet 5000 and 550 0 Series Printers Service Manual Figur e 30: Rollfeed Brakes 1 Left Hand Side Right Hand Side 2 3 and 4 5 and 6.
Parts and Diagrams 7-58 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual Miscellaneous Items Miscellaneous Items Reference on Drawing HP Part Number Quanti ty Descriptio n/Comments DJ 5000.
Parts and Diagrams 7-59 HP DesignJet 5000 and 550 0 Series Printers Service Manual Media T ypes ' H 89.
Parts and Diagrams 7-60 HP Design Jet 5000 and 5500 Series P rinters Se rvice Manual.
8-1 HP DesignJ et 5000 and 5500 Seri es Pr inters Ser vice Manual Removal and Installation 8 Screw T ypes 8-4 T op Cover Assembly 8-5 Left Ha nd Cover 8- 6 Right Hand C over 8-10 Front Pane l Assembly.
Removal and Installa tion 8-2 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Intr oduction This chapter is a step by step guide to th e r emoval and installation of the key components in the Printer . Y ou may find it useful to tick off the steps as they ar e pe rformed.
Removal and Installa tion 8-3 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Electr ostati c Discharge (ESD) Pr ecautions T o pr event damage to the Printer cir cuits fr om high-voltage electros tatic dischar ge (ESD): 1. Do not wear clothing that is subject to static build-up.
Removal and Installa tion 8-4 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Screw T ype s W ARNING Chassis scr ews have a copper washer and should never be r emoved.
Removal and Installa tion 8-5 HP Design Jet 5000 and 5500 Seri es Printers Service Manual T op Cover Assembly Removal W ARNING Switch off the Pri nter and remove the p ower cable . 1. Open the T op Cover and lift UP and remove from Printer (see detail of hinge mechanism below).
Removal and Installa tion 8-6 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Left Hand Cover Removal W ARNING Switch off the Pri nter and remove the p ower cable . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove ALL the Ink Cartridges from the Printer .
Removal and Installa tion 8-7 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 4. Disconnect the Electrical Cable from the rear of the Ink Cartridge Tube Connec tor . 5. Disconnect the Air T ube. 6. T wist the 3 latches at the rea r of the Ink Cartridge T ube Connector and release the compl ete Assembly .
Removal and Installa tion 8-8 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 7. Remove the Ink Cartridge T ube Connector and place safely on the window .
Removal and Installa tion 8-9 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 10. Remove 3 T -15 screws ( Ty p e F ) from the Left Hand Cover (front). 11 . Remove the Left H and Cover from the Printer . Installation of Le ft Hand Cover W ARNING When hand ling the T ubes make sur e you do not dam age them by twisting.
Removal and Installa tion 8-10 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Right Hand Cover Removal W ARNING Switch off the Pri nter and remove the Power Cord . W ARNING T o remove the Right Hand Cover you must open the Right Cover door and push in the Printhead Cl eaner Carriage.
Removal and Installa tion 8-11 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 4. Remove 1 T -15 scr ew ( Ty p e F ) and 1 T -25 scr ew ( Ty p e U ) (bottom) from the rear of the Right Hand Cover . 5. Open the T op Cover . 6. Raise the Medi a Lever .
Removal and Installa tion 8-12 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual NOTE T ake ca re no t to dr op t he Cover when removing the screws. Su pport the Cover thr oughout the next st ep. 7. Remove 3 T -15 ( Ty p e F ) scre ws from the front of the Right Hand Cover .
Removal and Installa tion 8-13 HP Design Jet 5000 and 5500 Seri es Printers Service Manual TIP T o ch eck correct fun ctioning of serviced parts on the Printer axis you can do the following: a Reinsert the top T -15 scr ew ( Ty p e F ) at the rear of the P rinter .
Removal and Installa tion 8-14 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Fr ont Panel Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove Right Rear Cover - Refer to Page 8-15 . 2. Remove Right Hand Cover - Refer to Page 8-10 .
Removal and Installa tion 8-15 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Left Rear Cover Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove one T -15 scre w ( Ty p e B ) from the Left Rear Cover .
Removal and Installa tion 8-16 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Right Rear Cover Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove one T -15 scre w ( Ty p e B ) from the Right Rear Cover .
Removal and Installa tion 8-17 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Extension Cove r (60" Model only) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-18 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Media Lever Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1.
Removal and Installa tion 8-19 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 5. Remove 1 T -15 scr ew ( Ty p e H ) that attaches the Le ver Arm to the Lever .
Removal and Installa tion 8-20 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Right Hand T rim Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-21 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 6. Carefully remove the Right Hand Tr i m . Installation of R ight Hand T rim W ARNING When in stalling the Media L ever in the T rim, install with the Lever in the UP position to avoid damagin g the Lever spring in the T rim.
Removal and Installa tion 8-22 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Left Hand T rim Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove 4 T -15 screws ( Ty p e F ) and 1 T -20 scre w ( Ty p e L ) from t he L eft Hand T rim.
Removal and Installa tion 8-23 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Back Cover Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the T op Cover - Refe r to Page 8-5 .
Removal and Installa tion 8-24 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. Remove the Back Cover . Installation of the Back Cov er NOTE If the Back Cover is r eplaced, remember to apply a new Printer Label to the new Back Cover before it is installed.
Removal and Installa tion 8-25 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Ink T ubes System Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Open the Right Cover door and pull out the Printhead Cleaner Carriage.
Removal and Installa tion 8-26 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. Slide the Carria ge to the position shown. 5. Push in the 2 reta ining clips either side of the Printhead T ube Connector . 6. Pull the Printhead T ube Connector towards you.
Removal and Installa tion 8-27 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 7. Push the button to rele ase the Printhea d T ub es in the Carriage. 8. Release the Retaining Clip by pulling it away from the holding brackets. 9. Pull the Printhead T ube Connector up between the two T ube Guides.
Removal and Installa tion 8-28 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 10. Lift out the blue Retaining Clip. 11 . Remove ALL the Ink Cartridges from the Printer .
Removal and Installa tion 8-29 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 13. Disconnect the Electrical Cable from the rear of the Ink Cartridge Tube Connec tor . 14. Disconnect the Air T ube. 15. T wist the 3 latches at the rea r of the Ink Cartridge T ube Connector and release the compl ete Assembly .
Removal and Installa tion 8-30 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 16. The complete assembly can now be removed by sliding the Ink Cartridge Connector out from the rear of the Left Hand Cover .
Removal and Installa tion 8-31 HP Design Jet 5000 and 5500 Seri es Printers Service Manual NOTE When the Ink T ubes System is replac ed, to r estart th e Printer perform the following procedur es. 1. Install the S etup Printheads (re fer to the User ’ s Guide).
Removal and Installa tion 8-32 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual EMC Covers Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. NOTE The EMC Cover is composed of three parts; T op , Lower Lef t and Lower Right.
Removal and Installa tion 8-33 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 7. Remove the following screws ( Ty p e N ) from the T op EMC Cover . 8 T - 15 screws for the 60" Model. 6 T - 15 screws for the 42" Model. 8.
Removal and Installa tion 8-34 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Encoder S trip Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove the Left Hand Cover - Refer to Page 8-6 . 2. Remove the Right Hand Cover - Refer to Page 8-10 .
Removal and Installa tion 8-35 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 8. Remove the 5.5 mm nut from the right hand side of the Printer .
Removal and Installa tion 8-36 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual T railing Cable Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the T op Cover - Refer to Page 8-5 .
Removal and Installa tion 8-37 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 7. Carefully disconnect the T railing Cables (3) from the connectors in the Carriage PCA. NOTE Remove T railing Cable Ferr ites if they fal l into t he Carriage 3 for 60" Model 1 for 42" Model 8.
Removal and Installa tion 8-38 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 10. Carefully disconnect the T railing Cable from the Main PCA. NOTE Unclip the T railing Cable when disconnectin g from the Main PCA. 11 . Remove the T -20 screw ( Ty p e C ) from the T rai ling Cable Clip on the left.
Removal and Installa tion 8-39 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 13. Carefully lift the Cli ps and the T r ailing Ca ble from the Printer .
Removal and Installa tion 8-40 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 2. Insert the T railing Cable Guide into the Carriage and connect the Trailing Cables. NOTE Remember to pass the T railing Cables thr ough the Ferrit e(s). 3 for 60" Model.
Removal and Installa tion 8-41 HP Design Jet 5000 and 5500 Seri es Printers Service Manual TIP Make sur e the T railing Cable is flat on the chassis without bubble s. NOTE Check the cable an d clips are corr ectly in stalle d by slidi ng the carriage along the Printer to see if it moves freely .
Removal and Installa tion 8-42 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual T ensioner Ass emb ly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-43 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 5. Using a screwdriver , fully tighten the Spring Release S crew to rele ase the tension on the Belt. 6. From the right-hand side, lift the T ensioner Belt off the Scan-Axis Motor .
Removal and Installa tion 8-44 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 8. Remove the Be lt Wheel on the l eft side. 9. Remove the T ensioner Assembly from the left-hand side.
Removal and Installa tion 8-45 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installat ion of T ensioner Assembly NOTE Before install ation, clean and oil the Slider Rods using the User’s Slider Rods Lu brificati on Kit (Refer to Page 9-8 ).
Removal and Installa tion 8-46 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Carriage Assembly and Be lt Removal W ARNING Switch off the Pri nter and remove the p ower cord. 1. Remove the Left Hand Cover - Refer to Page 8-6 . 2. Remove the Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-47 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 7. Lift up the Carriage Cover and remove ALL the Pri ntheads and close the Carriage Cover . 8. Slide the Carriage along the Printer to the position shown. 9. Push in the 2 reta ining clips either side of the Printhead T ube Connector .
Removal and Installa tion 8-48 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 10. Pull the Printhead T ube Connector towards you. 11 . Push the button to release the Printhea d T ubes in the Carriag e. 12. Release the retaining clip by pulling it away from the holding brackets.
Removal and Installa tion 8-49 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 13. Pull the Printhead T ube Connector up between the two T ube Guides. 14. Slide the Carria ge to the left si de of the Printer . 15. Unclip and remove the Carriage Cover to ac cess the T railing Cabl e in the Carriage.
Removal and Installa tion 8-50 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 16. Carefully disconnect the T railing Cables (3) from the connectors in the Carriage PCA. NOTE Remove T railing Cable Ferr ites if they fal l into t he Carriage 3 for 60" Model.
Removal and Installa tion 8-51 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 19. Slide the Ca rriage (inclu ding the Belt) to the left and out of the Printer . 20. Remove the Belt from the Carriage by releasing it from the retaining clips underneath the Carriage.
Removal and Installa tion 8-52 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installati on of Carriage a nd Bel t NOTE Before install ation, clean and oil the Slider Rods using the User’s Slider Rods Lu brificati on Kit (Refer to the Use r ’ s Guide).
Removal and Installa tion 8-53 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Line Sensor Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the Carriage Assembly - Refer to Page 8-46 .
Removal and Installa tion 8-54 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. Disconnect the Line Sensor Connector from the Carriage PCA.
Removal and Installa tion 8-55 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installa tion 1. When installing the new Line Sensor , make sure you insert the Line Sensor Cable through the correct hole (as highlighted).
Removal and Installa tion 8-56 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. Install the Ca rriage Cover . NOTE Make sure the cover i s installed vertically , if not the Cover Retaining Pins can be br oken.
Removal and Installa tion 8-57 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Scan-Axis Motor Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-58 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 6. Using a screwdriver , fully tighten the Spring Release S crew to rele ase the tension on the Belt. 7. Disconnect the Scan-Axis Motor Cable from positio n P23 on the Main PCA.
Removal and Installa tion 8-59 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 9. From the right-hand side, lift the T ensioner Belt off the Scan-Axis Motor . 10. While supporting the Scan-Axis Motor , remove 2 T -15 screw s ( Ty p e B ). 11 .
Removal and Installa tion 8-60 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Cutter Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Open the T op Cover .
Removal and Installa tion 8-61 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 4. Slide the Carria ge to the position shown. 5. Push in the 2 reta ining clips either side of the Printhead T ube Connector . 6. Pull the Printhead T ube Connector towards you.
Removal and Installa tion 8-62 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 7. Push the button to rele ase the Printhead T ubes from the Carriage . 8. Release the retaining clip by pulling it away from the holding brackets. 9. Remove 1 T -8 scr ew ( Ty p e V ) and washer that atta ches th e Cutter to the Carriage.
Removal and Installa tion 8-63 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 10. Slide the Cutter towards you and remove from the Print er .
Removal and Installa tion 8-64 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Ink Supply S t ation (ISS) Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove the Left Hand Cover - Refer to Page 8-6 . 2. Remove the Left Rear Cover - Refe r to Page 8-15 .
Removal and Installa tion 8-65 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 6. While pressing in the retaining clip (step 5), rotate the right side of the ISS up and left. 7. Pull out the right side of the ISS. 8. Slide the IS S to the left a nd pull out the left side to rem ove from the Printer .
Removal and Installa tion 8-66 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of I SS NOTE If the ISS is to be r eplaced, make sur e you r emove the APS from the old ISS and, after installing the Groundi ng Plate, reinstall it on the new ISS.
Removal and Installa tion 8-67 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Air Pressurization System (APS) Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove the Left Hand Cover - Refer to Page 8-6 . 2. Remove the Left Rear Cover - Refe r to Page 8-15 .
Removal and Installa tion 8-68 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of A PS W ARNING When In stalling the Air Pr essuri zation System make su re the tube and wir es ar e placed in th e dedicated slots and perform the following steps: 1.
Removal and Installa tion 8-69 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Service S t at ion Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-70 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 5. Disconnect the Service Station Cable from the Main PCA (P15) . 6. Unclip the S can-Axis Motor C able from the Serv ice S tation. NOTE Follow the i nstruction s in step 7 carefully; LOOSE N the screw and DO NOT r emove.
Removal and Installa tion 8-71 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 8. Remove 2 T -15 scr ews ( Ty p e F ) between the two slider rods that a ttach the Service S tation to the Chassis. 9. St anding in front of the Service St ation, lift it off the loosened screw .
Removal and Installa tion 8-72 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Drop Detector Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove the Right Rear Cover - Refer to Page 8-16 . 2. Remove the Right Hand Cover - Refer to Page 8-10 .
Removal and Installa tion 8-73 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 6. Remove the T -15 scr ew ( Ty p e F ) that attaches th e Drop Detector A ssembly to the Service Sta tion. 7. Remove the Drop Detector from the Servic e S tat ion.
Removal and Installa tion 8-74 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Hard Disk Drive (HDD) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-75 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installation of Hard Di sk Drive NOTE If you re place the Main PCA and the HDD at the same time you must perf orm ALL Ser vice Cal ibrations ( Page 5-3 ) and the EEROM Se tup Serv ice Utility ( Page 4-23 ).
Removal and Installa tion 8-76 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual LAN Card Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Disconnect the LAN cable from the LAN Card at the rear of the Printer . 2. Using a flat end screwdriver , unscrew the two screws that atta ch the LAN Card to the Printer .
Removal and Installa tion 8-77 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Memory a nd BootROM DIMM’ s Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-78 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 3. Pull out the DIMM. T ake care that it does not fall out. Installation of D IMM’ s W ARNING When in stalling the DIMM’ s make sur e they a re in the cor rect position as shown i n the diagram.
Removal and Installa tion 8-79 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Electr onics Module Cover Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-80 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual NOTE Lift the Par allel Port Clips before r emoving the Cover .
Removal and Installa tion 8-81 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Main PCA W ARNING This asse mbly does NOT inclu de the PCI-to-IDE PCA (t he small PCA that conne c ts the Main PCA to the Hard Disk Drive) as it used to in the past.
Removal and Installa tion 8-82 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the LAN Card - Refe r to Page 8-76 .
Removal and Installa tion 8-83 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 9. Disconnect the PCI-to-IDE PCA and remove from the Print er . NOTE Make sur e you re use the PCI-to-IDE PCA when r eassembling. 10. Remove 6 T -10 screws ( Ty p e K ) from the Main PCA.
Removal and Installa tion 8-84 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 12. Remove by sliding the Main PCA to the left and lifting out (see detail below). NOTE Detail of Main PCA removal. Installation of M ain PCA NOTE When the Main PCA has been replaced, perf orm the Back up EEROM Page 4-30 .
Removal and Installa tion 8-85 HP Design Jet 5000 and 5500 Seri es Printers Service Manual PCI-to-IDE PCA Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the LAN Card - Refe r to Page 8-76 .
Removal and Installa tion 8-86 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of the PCI- to-IDE PCA NOTE When installin g the ne w PCI-to-IDE PCA, CONNECT THE HDD POWER CA.
Removal and Installa tion 8-87 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installin g the HD D Cable When installing the HDD Cable between the H DD and the PCI-to-IDE PCA, make sure y.
Removal and Installa tion 8-88 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Power Supply Unit (PSU) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-89 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 7. Remove the plastic protective cover from the Power Supply Unit. 8. Disconnect ALL Cables from the PSU (see Installation of PSU for connections). 9. Remove 7 T -10 scr ews ( Ty p e K ) and remove the PSU.
Removal and Installa tion 8-90 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of the Power Supply Unit (PSU) W ARNING After in stalling t he Power Sup ply Unit, remember to place th e plastic protective cover over the unit.
Removal and Installa tion 8-91 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Ink Supply S t ation (ISS) PCA Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-92 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of the ISS PC A NOTE The ISS PCA co nnections ar e illu strated be low . * The Ink LeakDetector has been discontinued so this connector is no longer use d.
Removal and Installa tion 8-93 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Ink Leak Detector - If Pr es ent (Only Applicable to the 5000 Series) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-94 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 6. Press the ret aining clip on the Ink Leak D etecto r and r eleas e it. TIP A screwdriver can be used to press the retaining clip down. 7. Remove the Ink Leak Detector f rom the Printer .
Removal and Installa tion 8-95 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Cooling Fans Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the LAN Card - Refe r to Page 8-76 .
Removal and Installa tion 8-96 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 7. Remove the plastic Protective Cover from the Power Supply Unit. 8. Disconnect the Cooling Fan Cables from the Power Supply Unit. 9. Remove the Cooling Fans from the Printer .
Removal and Installa tion 8-97 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Electr onics Module (as one complete Assembly) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-98 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Pinch-Wheels Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the T op Cover - Refer to Page 8-5 .
Removal and Installa tion 8-99 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 6. First remove latera l Pinch-Wh eels with their Coupling Plat es.
Removal and Installa tion 8-100 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Pinch-Whee l Cam Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-101 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 16. Remove the Center Guide - Refer to Page 8-1 12 . 17. Remove the Pinch-Wheels - Refer to Page 8-97 . 18. Through the slot in the right Sideplate, remove the T -15 screw ( Ty p e H ) retaining the cam lever a rm.
Removal and Installa tion 8-102 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of C am 1. T o install the Cam slide it through the left Sideplate and place it in the cam slot in the beam. 2. Hold the Cam Lever Linkage over its slot in the Sideplate and insert the Cam into it.
Removal and Installa tion 8-103 HP Design Jet 5000 and 5500 Seri es Printers Service Manual V ac uum Fan Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove the Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-104 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 6. Remove the V acuum Fan. Installation of V acuum Fan W ARNING When installing the V acuum Fan make sur e that it fits tightly to the Guide s in the S ideplate.
Removal and Installa tion 8-105 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Paper -Axis Motor Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-106 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 6. Remove the Hel ical Gear . 7. Remove the 3 T -20 scr ews ( Ty p e L ) that secure th e Paper-Axis Motor Assembly to the S ideplate. 8. Remove the Paper-Axis Mot or Assembly .
Removal and Installa tion 8-107 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installation of P aper -Axis Motor Ass embly W ARNING When r einstallin g parts make su re that the y fit tightly and that screws ar e tight. NOTE Apply gr ease to the Helical Gear .
Removal and Installa tion 8-108 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Booster Fan Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-109 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Media Sensor Removal W ARNING Switch off the Pri nter and remove the Power Cord . 1. Remove the T op Cover - Refer to Page 8-5 . 2. Remove the Right Rear Cover - Refer to Page 8-16 .
Removal and Installa tion 8-110 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Installation of M edia Sensor W ARNING When installing th e Media Sensor , insert the moving part as shown in the diagram.
Removal and Installa tion 8-111 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Entry Roller Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1. Remove Left Hand T rim - Refer to Page 8-22 .
Removal and Installa tion 8-112 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Center Guide Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-113 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 16. Remove the Booster Fan - Refer to Page 8-108 . 17. Remove the Media Sensor - Refer to Page 8-109 . 18. Remove the Entry Roll er - Refer to Page 8 - 111 . 19.
Removal and Installa tion 8-114 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Drive Roller Gear Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types. 1.
Removal and Installa tion 8-115 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Fr ont Platen Ass embly (Only A pplicable to the 5000 Series) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-116 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 4. Remove the Pl aten starting from the left side..
Removal and Installa tion 8-117 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Center Plat en Assembly Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-118 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 3. Remove the c omplete Cent er Platen Assembly (includes the Overdrive Assembly and the Cutter guide). NOTE Y ou must perform th e following Calibrations when the C enter Platen Assemb ly is r eplaced: Scan Axis Calibration P age 5-7 .
Removal and Installa tion 8-119 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Deflectors (Only Applica ble to the 5000 Series) Removal NOTE Refer to the table on Page 8-4 for information on screw types. 1. Unclip the Deflector Extension.
Removal and Installa tion 8-120 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual Heater A ssembly (Only Applicable to the 5500 Series) Removal W ARNING Switch off the Pri nter and remove the Power Cord . NOTE Refer to the table on Page 8-4 for information on screw types.
Removal and Installa tion 8-121 HP Design Jet 5000 and 5500 Seri es Printers Service Manual 5. Remove 15 screws that secure the Heater from the top of the Printer . NOTE The 42" Printer only has 1 1 screws securing the Heater from the top. NOTE Be very car eful not to forc e the screws as th ey are scr ewed directly to the Print er Chassis.
Removal and Installa tion 8-122 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual 8. Before removing the Heather completely , pull out the Heate r Cable from the access ho le in the s ideplat e.
Removal and Installa tion 8-123 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Installing the Heater T o install the Heate r , follow t he removal pro c edures in rever se order , taking care of the following information: 1.
Removal and Installa tion 8-124 HP Desig nJet 500 0 and 5500 Serie s Printer s Service Manual T ube Gu id e Door The T ube Guide Door kit contains 2 dif ferent types of springs which need to be installed depending on the design of the T ube Guide. Refer to the drawing below to determine which spring needs to be installed.
9-1 HP Design Jet 5000 and 5500 Seri es Printers Service Manual Pr eventive Maintenance 9 Introdu ction 9- 2 Service Prev entive Maintenan ce 9-2 W arning/S top T r iggers 9-3 User Maintenance 9-5 Len.
Preventive Ma intenance 9-2 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Intr oduction This chapter explains how to perform service preventive maintenance procedure s when they are required, and routine maintenance procedures that are r ecommended when Service Engineers perform Removal and Installation procedures.
Preventive Maintenance 9-3 HP DesignJ et 5000 and 5500 S eries Pr inters Ser vice Manual W arning/S top T riggers NOTE If the Ink T ubes System needs to b e replaced , this can be perform ed by th e User . The Printer will advise the User when the Scan- Axis System and/or T ube s need to be replaced by displaying a W arning message.
Preventive Ma intenance 9-4 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual If the Ink T ubes reach 7 million cycles, they ris k breakage.
Preventive Maintenance 9-5 HP DesignJ et 5000 and 5500 S eries Pr inters Ser vice Manual User Maintenance W arranty S tatement HP’ s li mited warranty covers onl y those defects which ari se as a result of appr opriate use of t he pro duct, and does not apply t o any: a.
Preventive Ma intenance 9-6 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Carriage Inter connect Wiper NOTE The Ca rriage Interconnect Wiper also comes wit h the Carriage.
Preventive Maintenance 9-7 HP DesignJ et 5000 and 5500 S eries Pr inters Ser vice Manual Roller Lubri fication Kit W ARNING This pr ocedur e is for Service Engineers only .
Preventive Ma intenance 9-8 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Slider Rod s Lubrification Ki t In addition to the wea ring of the S can-Axis Motor , the friction in this area can inc rease due to the accumula tion of ink partic les and dust from the media or the atmosphere in the vicinity of the Slider Rods.
Preventive Maintenance 9-9 HP DesignJ et 5000 and 5500 S eries Pr inters Ser vice Manual Cleaning the Platen W ARNING This pr ocedur e is for Service Engineers only .
Preventive Ma intenance 9-10 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Moistur e on the Printer Users should use the Printer in an environment between 20% and 80% relative humidity .
Preventive Maintenance 9-11 HP DesignJ et 5000 and 5500 S eries Pr inters Ser vice Manual Firmwar e Upgrade This section explains how to perform the System Software (Firmware) Upgrade and the Interna l Demo Prints Upgrade (Only for the PostScr ipt Print er) when they ar e required.
Preventive Ma intenance 9-12 HP Design Jet 5000 and 5500 S eries Pri nters Service Man ual Upgrade Instructi ons - 5000 Series ONL Y 5500 SERIES ONL Y UPGRADE INSTRUCTIONS FOR THE 5500 SERIES CAN BE FOUND IN THE USER’S GUIDE W ARNING The Firmware Up grade pr ocess will delete all p ending print jobs.
10-1 HP DesignJet 5000 and 550 0 Series Printers Service Manual Functional Overview 10 Introdu ction, pag e 10-2 Electri cal System, page 10-2 Front Panel, page 10-3 Scan Axis, page 1 0-3 Paper Axis, .
Functional Overview 10-2 HP DesignJet 5000 Series Printers Service Manual Intr oduction This Chapter contains a simplified description of the HP DesignJet 5000 and 5500 Series Printers.
Functional Overview 10-3 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Front Panel The Front Panel is used to displa y messages, configure the Printer and send commands to the Printer via the keys. The display is a 128 x 64 pixel graphic LCD and can display both text and graphics a t the same time.
Functional Overview 10-4 HP DesignJet 5000 Series Printers Service Manual Paper Axis The Paper Axis determines the motion of the media through the printer . Its main parts are: Paper-Axis Mot or - provides traction to the Overdrive. Center Platen and Overdrive - c ontrols the printing path and expansion of the media.
Functional Overview 10-5 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Ink Delivery System (IDS) The Ink Delivery System (IDS) delivers ink under pressure from the lar ge capacity off-axis Ink Cart ridges via permanently c onnected tubes to the high throughput Printheads.
Functional Overview 10-6 HP DesignJet 5000 Series Printers Service Manual Ink Supply S tation (ISS) In the Printer , the Ink Ca rtridges re side inside the Ink Sup ply Station (ISS).
Functional Overview 10-7 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual The T ubes move back and forth inside the volume defined by the T ube Guides.
Functional Overview 10-8 HP DesignJet 5000 Series Printers Service Manual Air Pr essurization Sys tem (APS) The APS is the system that provide s and controls t he pressurization of the ink in the Ink Cartridges and is located under the ISS.
Functional Overview 10-9 HP Design Jet 500 0 and 5500 Series Pri nters Serv ice Manual Service S tation The Service Station consists of a linear motion mechanism with a chassis containing one PrintHead Cleane r (PHC) for eac h printhead. Attached to the Service Station chassis, one optical drop detector provides nozzle ch eck functionality .
Functional Overview 10-10 HP DesignJet 5000 Series Printers Service Manual.
About this Ed ition This is the 2nd edition of this Service Manual 1st edition, titled HP Desig nJet 500 0 and 50 00PS Se rvice Manual - August 2000 2nd edition, titled HP Desig nJet 500 0 and 5000 PS.
1 What’ s in this Service Manual This manual contains information necessary to test, calibrate and serv ice: - HP De signJet 5000 P rinter - 42” Model ( P/N C609 0A/V) - HP De signJet 5000 P rinte.
Ein wichtiger Punkt beim Kauf des Geräts HP (Hewlett-Packard) 5000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HP (Hewlett-Packard) 5000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HP (Hewlett-Packard) 5000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HP (Hewlett-Packard) 5000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HP (Hewlett-Packard) 5000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HP (Hewlett-Packard) 5000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HP (Hewlett-Packard) 5000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HP (Hewlett-Packard) 5000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HP (Hewlett-Packard) 5000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
