Benutzeranleitung / Produktwartung MODULAR CRESCENT CUBER KML-450MWH des Produzenten Hoshizaki
Zur Seite of 22
ISSUED: HOSHIZAKI MODULAR CRESCENT CUBER INSTR UCTION MANU AL FEB. 21, 2001 MODELS KML-450MAH KML-450MWH REVISED: SEPT . 24, 2001 TM.
2 HOSHIZAKI AMERICA, INC. 618 Highway 74 South Peachtree City , GA 30269 Attn: HOSHIZAKI T echnical Support Department Phone: 1-800-233-1940 T echnical Service (770) 487-2331 Fax: (770) 487-3360 NO TE.
3 • Please review this manual. It should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service and maintain the icemaker. This manual should be made available to the technician prior to installation, maintenance or service.
4 I. SPECIFICA TIONS 1. NAMEPLA TE RA TING [a] KML-450MAH (Air-cooled) See the Nameplate for electrical and refrigeration speci- fications. This Nameplate is located on the upper right hand side of the rear panel.
5 [b] KML-450MWH (Water-cooled) See the Nameplate for electrical and refrigeration speci- fications. This Nameplate is located on the upper right hand side of rear panel. Since this Nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or against another piece of kitchen equipment.
6 2. DIMENSIONS/CONNECTIONS [a] KML-450MAH Unit: inches (mm.).
7 [b] KML-450MWH Unit: inches (mm.).
8 II. INST ALLA TION AND OPERA TING INSTR UCTIONS 1. CHECKS BEFORE INST ALLA TION IMPORT ANT Remove shipping carton, tape(s) and packing. If packing material is left in the icemaker, it will not work properly. 1) Remove the panels to prevent damage when installing the icemaker.
9 2. HOW TO REMOVE PANELS - See Fig. 1 a) Front Panel ......... Remove the screw. Lift up and pull toward you. b) Top Panel ............ Lift its front up slightly, push away, and then lift off. c) Side Panel (R) ..... Remove the screw. Pull slightly toward you, and lift off.
10 4. SET UP 1) Unpack the Storage Bin, and attach the four adjustable legs provided (bin accessory) to the bottom of the Storage Bin. 2) Position the Storage Bin in the selected permanent position. 3) Place the icemaker on the top of the Storage Bin.
11 6. W A TER SUPPL Y AND DRAIN CONNECTIONS - See Fig. 4 IMPORT ANT Do not operate the icemaker when the water supply is OFF, or if the pressure is below 10 PSIG. Do not run the icemaker until the proper water pressure is reached. • Water supply inlet is 1/2" female pipe thread (FPT).
12 Fig. 4 KML-450MWH KML-450MAH.
13 7. FINAL CHECK LIST 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F and the water temperature within +45°F to +90°F all year aroun.
14 8. ST AR T UP CAUTION 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the Compressor. 3. Do not operate the unit in the “WASH” position without water in the Water Tank.
15 Note: The Bin Switch will only shut down the unit at the end of a harvest or within the first 5 minutes of the freeze cycle. To shut the unit down outside of this time period turn the control switch to “OFF”. 8) Replace the Bin Control Cover. 9) Move the Control Switch to the “Service” position.
16 9. PREP ARING THE ICEMAKER FOR LONG ST ORA GE CA UTION When shutting off the icemaker for an extended time, drain out all water from the water line and remove the ice from the Storage Bin.
17 [2] Remove the water from the potable water supply line: 1) Turn off the power supply and remove the Front Panel. 2) Move the Control Switch, on the Control Box, to the “OFF” position. 3) Wait 3 minutes. 4) Close the Potable Water Supply Line Shut-off Valve and open the Potable Water Supply Line Drain Valve.
18 III. CLEANING AND MAINTENANCE INSTR UCTIONS 1. CLEANING INSTR UCTIONS W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year. More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker, do not use ammonia type cleaners.
19 10) Move the Service Switch to the “WASH” position. 11) Replace the Insulation Panel and the Front Panel in their correct positions. 12) Turn on the power supply and start the washing process. 13) Turn off the power supply after 30 minutes. 14) Remove the Front Panel.
20 Note: If you do not sanitize the icemaker, go to step 14) in “SANITIZING PROCEDURE.” [b] SANITIZING PROCEDURE - Following Cleaning Procedure 1) Dilute IMS-II Sanitizer or a 5.25% Sodium Hypochlorite solution with water (Add 1.0 fl. oz. to 2 gal.
21 2. MAINTENANCE IMPORT ANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1) Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth.
22 91A1BE10B HOSHIZAKI HOSHIZAKI AMERICA, INC. 618 HIGHW A Y 74 SOUTH PEA CHTREE CITY , GA 30269 U .S.A. PHONE: 770-487-2331.
Ein wichtiger Punkt beim Kauf des Geräts Hoshizaki MODULAR CRESCENT CUBER KML-450MWH (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hoshizaki MODULAR CRESCENT CUBER KML-450MWH noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hoshizaki MODULAR CRESCENT CUBER KML-450MWH - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hoshizaki MODULAR CRESCENT CUBER KML-450MWH reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hoshizaki MODULAR CRESCENT CUBER KML-450MWH erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hoshizaki MODULAR CRESCENT CUBER KML-450MWH besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hoshizaki MODULAR CRESCENT CUBER KML-450MWH verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hoshizaki MODULAR CRESCENT CUBER KML-450MWH. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hoshizaki MODULAR CRESCENT CUBER KML-450MWH gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
