Benutzeranleitung / Produktwartung 53441 des Produzenten Hoover
Zur Seite of 20
.
Fill in;and:mWn ! The HOOVER commercial upright cleaner you have just purchased is for carpet and rug cleaning. The cleaning tool attachments are for floor cleaning and above the floor cleaning. Your cleaner is a model . . . . . . . . . . . . . . . . .
ImDortantsa#eauards! I- - -u- - l Read all instructions. l Warning: Electric shock could occur if used outdoors or on wet surfaces. l This cleaner has been equipped with a 3-wire grounding cord in compli- ance with electrical codes devised for your safety.
UNPACKING THE CLEANEd ’ Unpack the cleaner from the carton and identify the parts shown in Fig. 1. cc Remove and dispose of the cardboard 1 1, m-b-- I packing. 1. Upper handle section 2. Lower handle section 3. Cleaner base 4. Cloth bag assembly The cleaner assembled will look like the drawing below.
HOW TO ASSEMBLE A. Attach handle to the cleaner Unscrew nut and remove bolt and plate from handle socket. Place bottom section of handle into handle socket lining up small holes toward front of cleaner. Cord will run up indentation at base of handle, Insert bolt into hole in front of handle.
B. Join upper and lower handles Join upper and lower handles, aligning holes. Place cord clip around cord with flat side toward handle of cleaner and holes to the front. Insert bolt through washer, cord clip and both parts of the handle (small holes).
Upright Handle adjustments The handle has three positions: Up- right for storage and when using attachments. Operating for general operation on carpet and floors. Low for reaching under low furniture. Adjustment for carpet pile height The cleaning of carpet and rugs takes place at the nozzle.
SPECIAL FEATURES Carrying handle Your cleaner has a convenient carrying handle located underneath the handle bail. Edge cleaning This feature improves the cleaning of carpet edges near baseboards and solid furniture. Dust and lint tend tocollect along these edges.
CLEANING TOOL ATTACHMENTS Cleaning tools are available at additional cost from Hoover Dealers. The clean- ing tools allow you to do above the floor cleaning and to clean hard to reach areas.
Grasp the converter; turn red con- verter lock away from the hose. Fig. 5. Bring converter up until it covers the opening. Fig. 7. d Push connector and converter togeth- er and twist. The converter is locked into position when the projections on the converter fit into the holes on the hose connec- tor.
9. Select the proper cleaning tool The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descriptions below. Wall/floor brush* For walls and very irregular hard surface floors such as brick and slate.
. Turn the plastic ring counterclock- wise to lock the tool in place. Fig. 8. For additional length, attach one or both* wands to the vinyl hose as de- scribed above. To attach the tools to the other end of the wand, press down firmly on the white plastic spring latch.
Storing attachments For Storage, the attachment set will conveniently fit in the storage bag.* The bag has two slots located near the top for use in hanging. Therefore, it can be attached to the cleaner or hung conveniently on a hook in the closet. To clean attachments To clean the hose wipe off dirt with a cloth damp- ened with a liquid detergent.
Empty bag by placing large opening over a paper. The bulk of the dirt will fall on the paper. Shake bag until clean. Replace the bag closure clip and at- tach bag to cleaner following the instructions give on page 5.
2. Release worn belt from pulley. 3. Lift out rug agitator, remove old belt and place new belt in groove of rug agitator. 4. Replace agitator. On one end of the agitator roll there is a raised metal plate. Make sure that this end is placed in groove on side of cleaner.
The brushes When to replace brushes When brushes are worn and bristles do not touch the edge of a card held across the bottom plate, they should be replaced. Always replace both brushes at the same time to maintain cleaning effectiveness. What brushes to buy When purchasing new brushes, ask for Hoover Part No.
6. Remove brushes by pulling them from agitator. Slide new brushes into channels. Push them in as far as possible. 7. To reassemble, replace shaft and end assembly lining up the locator with the slot in the agitator. Press into place. Place remaining end sec- tion over the shaft end, lining up the locator and slot.
USER CHECK LIST This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accordingly, this check list is provided for your convenience.
ENERGY SAVING TIPS 1. Empty cleaner bag promptly, before overfilled. 2. To maintain effective cleaning, replace agitator brushes and belt when necessary.
VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER -AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety.
Ein wichtiger Punkt beim Kauf des Geräts Hoover 53441 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hoover 53441 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hoover 53441 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hoover 53441 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hoover 53441 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hoover 53441 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hoover 53441 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hoover 53441. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hoover 53441 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
