Benutzeranleitung / Produktwartung 9950 des Produzenten Honeywell
Zur Seite of 154
Dolphin ® 9900 Mobile Computers Dolphin 9900 Dolphin 9950 Dolphin 9951 with Windows Mobile ® 6.1 User’s Guide.
Disc laimer Honeywell International Inc. (“HII”) reserves the ri ght to make changes in specifications and other information contained in this docume nt without prior notice, and the reade r should in all cases consult HII to determine whether any such changes have been made .
iii Chapter 1 - Agency Information Label Locations ................................................. ............................................................... ....1-1 LED Safety Statement ........................................ ................
iv Batteries ...................................................................................................................... ...... 3-14 Main Battery Pack................................... ................................. ....................
v System Tab ................................................. .................................................................... .... 6-7 About ........................................................................................................
vi Voice Communication ................................... ................................. ...................................... 8- 5 Audio Modes ..................................................... ................................ ...............
vii Communicating with the Dolphin Terminal ........... .................................. ........................... 11-8 Verifying Data Transfer ................................... ............................................................. 11-8 RS-232 Communications Cables .
viii.
1 - 1 1 Agency Inf ormation Dolphin 9900, 9950, and 9951 terminals meet or ex ceed the requirements of all applicable standards organizations for safe operation. However, as with an y electrical equipment, the best way to ensure safe operation is to operate them according to the agency gu idelines that follow.
1 - 2 LED Safety Statement The LED output on this device has been tested in accordance with IEC6 0825-1 LED safety and certified to be a Class 1 LED device. The maximum power outputs for each diode are as follows: • Illumination LED: 194.0 uW, wavelength: 626nm+/-30nm • Aimer laser (5300 engine): 360.
1 - 3 Appr o v als b y Country *Applies to 99XXXXX-XXXXXXI units. This Class 2 Laser Product is in accordance with the requirements of IEC 60825-1 Ed. 1.2 Clause 6.2(a). R&TTE Compliance Statement—802.11b/g, Bluetooth, and/or GSM Dolphin RF terminals are in conformity with all esse ntial requirements of the R&TTE Directive (1999/5/ EC).
1 - 4 Dolphin RF T erminal—802.11b/g, Bluetooth, and/or GSM This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference th at may cause undesired operation.
1 - 5 In order to avoid the dissemination of those substanc es in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.
1 - 6.
2 - 1 2 Getting Star ted Out of the Bo x Verify that the carton contains the following items: • Dolphin 9900 or 9950 or 9951 mobile computer (the terminal) • Main battery pack (7.
2 - 2 Step 2. Charge the Main and Backup Batteries The power supply for Dolphin terminals consists of two types of battery powe r: the main battery pack installed on the back panel and the backup ba ttery that resides inside the terminal. The main battery powers the terminal.
2 - 3 The Clock Settings screen appears. The time zone defaults to GMT-5 Eastern US ; tap the arrow to the right of GMT-5 Eastern US to select another time zone. Set the correct time and date in the remaining fields and tap OK to save. T oda y Screen After the Dolphin terminal initializes the first time, you see the Today screen.
2 - 4 Command Bar The Command bar is located at the bottom of application windows. Menus change according to the open application. The Task tray displays icons for programs running in the background.
2 - 5 Icons in the Navigation Bar Indicator Meaning The term inal could not synchroniz e data with the workstation via ActiveSync. New e-mail or te xt message (SMS) New v oicemail New instant message Ringer off Vo i c e c a l l V oice call in progress Calls are f orwarded Call on hold Missed call Data call in progress Batter y le v els (1–4).
2 - 6 P op-Up Menus With pop-up menus, you can quickly choose an acti on for a selected item. To access a pop-up menu, tap and hold the stylus on the item name of the action you want to perform. When the menu appears, lift the stylus, and tap the action you want to perform.
2 - 7 File Explorer You can also use the File Explorer to find fi les and organize these files into folders. Tap Start > Programs > File Explorer .
2 - 8.
3 - 1 3 Har d ware Overview Standar d Configurations for the 9900 Some configurations of the 9900 terminal are availabl e with an external housing made of plastic that is specifically designed for the healthcare industry. For more information, see Healthcare Housing on page 3-14 .
3 - 2 P eripherals f or the 9900, 9950, and 9951 Each of the following items is sold separately to enhance the capabilities of your Dolphin terminal. Dolphin HomeBase ™ Device The Dolphin HomeBase d.
3 - 3 Accessories f or the 9900, 9950, and 9951 Each of the following items is sold separately to enhance your terminal’s capabilities. Note: When using accessories where the terminal is worn on the body, the terminal’s touch panel must face away from the body.
3 - 4 Fr ont P anel: 9900, 9950, and 9951 Indicator LED Touch Panel Display Navigation Keys SCAN Key Recessed Keyboard Front Speaker I/O Connector.
3 - 5 Front P anel Features for the 9900, 9950, and 9951 Front Speaker The integrated speaker that sounds audio signal s as you scan bar code labels and enter data. The operating frequency range is 50 0Hz at 71 dB up to 80 dB. I/O Connector See I/O Connector on page 3-12 .
3 - 6 Bac k P anel: 9900 For a description of each callout, see Back Panel Features for the 9900, 9950, and 9951 on page 3-9 . Battery Well Image/Scan Engine Window Stylus Slot Rear Speaker Microphone.
3 - 7 Bac k and Side P anels: 9950 and 9951 The back panel of the 9950 and 9951 contains an inte grated, pistol-grip handle for a more ergonomic grip in scan-intensive applications. The stylus is stored inside the handle for easy access. Side P anel Scan Trigger Press the scan trigger to activate the image or scan.
3 - 8 Back P anel For a description of each callout, see Back Panel Features for the 9900, 9950, and 9951 on page 3-9 . Image/Scan Engine Window Pistol-Grip Handle Battery Well Rear Speaker.
3 - 9 Bac k P anel Features f or the 9900, 9950, and 9951 Battery Well The Battery Well is a recessed area on the back panel that holds the Li-ion battery pack.
3 - 10 Side P anels: 9900, 9950, and 9951 The left and the right side panels contain different features. Left Side Memory Card Door This door provides user access to the industry -standard SD memory interface. You can open this door to insert SD memory cards to expand the terminal’s memory capacity.
3 - 11 Installing a Memory Card 1. Press the Power key to put th e terminal in Suspend Mode; see Suspend Mode on page 3-18. 2. Remove the battery. 3. Place the terminal on a flat, secure surface with the keyboard face down. 4. Unscrew both screws and remove the door.
3 - 12 Bottom P anel: 9900, 9950, and 9951 I/O Connector The I/O connector powers the terminal, charges the ma in battery, and facilitates communication. All Dolphin peripherals are designed to work exclusively with this connector. The I/O connector supports RS-232 and USB communi cation.
3 - 13 Using the T ouch P anel Honeywell defines proper use of the terminal touch p anel as using a screen protector and proper stylus. Screen protectors maintain the ongoing integrity (i.
3 - 14 Healthcare Housing Some configurations of the 9900 te rminal are available with an external plastic housing that is designed to resist the effects of harsh chemicals in a healthcare environment. The plastic is crystalline in nature, which helps prevent chemicals from seeping through the housing.
3 - 15 • Dolphin HomeBase Device (see page 11-1) • Dolphin Mobile Base Device (see page 12-1) • Dolphin ChargeBase Device (see page 13-1) • Dolphin Net Base (Please see the Dolphin Net Base Quick Start Guide on www.
3 - 16 Charging The internal backup battery is power ed by the main battery pack. Theref ore, charging the internal backup battery requires that the main battery pack be installed in the terminal and the terminal be connected to a charging device. The internal backup battery must be fully charged before using the terminal for the first time.
3 - 17 Setting Critical and Low Batter y P oints Developers can reset the battery parameters in the re gistry from 0 (no warning) to 99 (would nearly always warn). You can review and set these battery points in the RegEdit Power Tool. 1. Tap Start > Power Tools > RegEdit .
3 - 18 Resetting the T erminal There are two types of system resets: a soft and a hard reset. Soft Reset (W arm Boot) A soft reset re-boots the device without losing RAM data. You would perform a soft reset when • the terminal fails to respond. • after installing some software applications.
4 - 1 4 Using the Scan Image Engine Overview The Dolphin terminal houses a compact image engine t hat instantly reads popular 1D and 2D bar codes and supports omni-directional aiming and decoding for greater flexibility in real-world settings. The image engine can also capture digital images, such as signatures and pictures of damaged inventory.
4 - 2 A vailable Laser Engines Laser Specifications The maximum power outputs for each diode are as follows: • Illumination LED: 194.0 uW • Aimer laser (5300 engine): 360.1 uW • Aimer LED (5100 engine): 81.6 uW High Performance (HP) 5 mil 55 mil reflective W orking Rang e: Near 2.
4 - 3 Suppor ted Bar Code Symbologies Symbology T ype Symbology Name 1D Symbologies Codabar Code 3 of 9 Code 11 Code 32 Pharmaceutical (P ARAF) Code 93 Code 128 EAN with Add-On EAN with Extended Coupo.
4 - 4 Decoding The terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging a nd Advanced Linear Decoding (ALD). Full-Area Imaging Full-area imaging provides omni-directional reading of linear and non-linear 1D and 2D bar codes, OCR, signature capture, and picture taking.
4 - 5 Aiming Options The aiming beams are smaller when the terminal is held closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elem ents (mil size) should be read closer to the unit whereas symbologies with larger bars or elements (mil size) should be read farther from the unit.
4 - 6 Capturing Images The image-capture process is an intuitive, split-secon d operation for experienced users. By following the basic guidelines, new users can easily develop their own technique and, with practice, quickly learn to adapt it to different application environments.
4 - 7 Enab ling the Aimer If your Dolphin terminal is configured with the 5300 imager, you can enable the aiming pattern for imaging in the Imaging Demo. For details about the aimer, see 5300 Red High-Vis Aiming Pattern on page 4-5 . 1. Tap Start > Demos > Imaging Demo > Setup menu > Aimer .
4 - 8.
5 - 1 5 Using the K e yboar ds A vailable K e yboar ds There are three keyboard options in the 9900 series: All Ke yboar ds Contain the Follo wing: • Backlit for easy viewing in various lighting conditions. • Centrally-located keys for both right- and left-hand operation.
5 - 2 Common Buttons See Using the Function Keys on page 5-2. See Using the Modifier Keys on page 5-3. See Using the Navigation Keys on page 5-3. Using the Function Ke ys Name Ke y Function Backlight T urns the ke yboard bac klight on and off . Backspace (BKSP) Mov es the cursor bac k one space each time the k ey is pressed.
5 - 3 Using the Modifier Ke ys Using the Navigation K e ys Located in the center of each keyb oard for easy access with either hand, the navigation keys navigate the cursor through application screens. Note: Additional functionality varies according to the application in use.
5 - 4 Stic ky Ke y Functionality Sticky key functionality is supported for the CTRL key, which means that you don’t have to press and hold the CTRL key when you press the next key. In stead, just tap CTRL and then the next key. You need to open RegEdit and enable the HKEY_LOCAL_MACHINEHARDWAREDEVICEMAPKEYBD key.
5 - 5 35-Ke y Alpha/Numeric K e yboar d ALPHA Ke y The ALPHA key enables you to toggle between the alpha and numeric modes. • Single-tap ALPHA to switch only the next key pressed to alpha mode. • Double-tap ALPHA to switch the keyboard to alpha mode.
5 - 6 35-Ke y K eyboar d Combinations Ke y NUM Shift-NUM Alpha Shift-Alpha BLUE RED Pow e r Suspend/Resume Scan Scan Scan Scan Scan ESC Escape Escape Escape Escape Backlight T oggles K eyboard Bac kli.
5 - 7 BKSP Backspace Backspace Bac kspace Bac kspace @ Delete Delete Delete Delete Delete Inser t CTRL Control Control Blue Blue Blue Red Red Red AL T Menu Menu Ke y NUM Shift-NUM Alpha Shift-Alpha BL.
5 - 8 43-Ke y Alpha/Numeric K e yboar d Number Lock (NUM) K e y The Number Lock key enables you to toggle between the alpha and numeric modes. Alpha mode is when you type letters with the letter keys. Numeric mode is when you type numbers with the letter keys.
5 - 9 43-Ke y K eyboar d Combinations Alpha Alpha Shift NUM Lock NUM Shift BLUE RED a A1 ! b B2 @ c C3 # d D d D - (subtract) e E4 $ f F5 % g G6 ^ h H h H _ (underscore) i I7 & j J8 * k K9 ( l L l L = (equals) m M .
5 - 10 Down arr o w Down Down Down V o lume do wn P age down SFT Shift Shift Shift Send (a phone call) ENT Enter Enter Enter End (a phone call) 43-Ke y K eyboar d Combinations Alpha Alpha Shift NUM Lo.
5 - 11 56-Ke y Full Alpha/Numeric K e yboar d SCAN SFT ESC TA B EN T CTRL SP BKSP DEL INS 12 3 4 5 6 789 0 ABC DE FG H I J K L MNO P Q R S T U VWX Y Z VOL PG END SEND _ @ F6 F6 F7 F7 F8 F8 F9 F9 F10 F.
5 - 12 56-Ke y K eyboar d Combinations Ke y SHIFT BLUE RED 1 ! 2 @ 3 # 4 $ 5 % 6 ^ 7 & 8 * 9 ( 0 ) , (comma) < # (pound) . (period) > * (asterisk) A + (plus) F1 B ; (semi-colon) F2 C [ (left.
5 - 13 R F18 S F19 T F20 U Star t menu F21 V F22 W F23 X F24 Y F25 Z Up arro w V olume up P age up Down arr o w V olume down Page do wn SFT Send (a phone call) ENT End (a phone call) Blue T oggle CAPS.
5 - 14 General Windows K e yboar d Shortcuts Press these keys, T o… CTRL + C Cop y CTRL + X Cut CTRL + V P aste CTRL + Z Undo DELETE Delete CTRL + Right Arro w Mo v e the inser tion point to the beginning of the ne xt word. CTRL + Left Arro w Mov e the inser tion point to the beginning of the pre vious word.
6 - 1 6 System Settings Overview Customized settings are available on the Start menu. Tap Start > Settings and the settings screen opens displaying the Personal tab. Settings consists of three tabs: Personal, System, and Connections. T ab Description See P age Personal Customizes b uttons, set SIP options , and adjust headset settings.
6 - 2 P er sonal T ab To access the Personal tab, go to Start > Settings . The screen opens displaying the Personal tab. Note: Personal settings are stored in RAM memory. They are replaced by system defaults after each hard reset. For more information about resets, see Soft Reset (Warm Boot) on page 3-18.
6 - 3 Buttons The Buttons setting programs certain keyboard button s to launch applications or execute commands. Enab le HotK eys Default Buttons setting assignments inactive until you enable the HotKeys Power Tool. Tap Start > Power Tools and tap the HotKeys icon once .
6 - 4 Input The Input settings enables you to customize input fr om the SIP, adjust word completion settings in Microsoft applications. <None> Nothing happens when the button is pressed. <OK/Close> P erforms the same function as tapping OK on the screen.
6 - 5 Menus You can add existing programs you use often, such as File Explorer, to the Start menu for faster access. You are not installing the program, just allowing access to it from the Start menu.
6 - 6 2. Tap and hold on the program, then tap Copy on the pop-up menu. 3. Navigate to the Windows folder and open the St art Menu (My Device > Windows > Start Menu), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu.
6 - 7 System T ab The System tab enables you to verify and sometime s alter system parameters. To access the System tab, go to Start > Settings > System tab. Tap the appropriate icon to open that system setting. Icon See P age About See About on page 6-8.
6 - 8 About The About system setting displays specific informati on about the terminal. It contains three tabs: Version Tab Displays the information about the software, operating system, and processor. Device ID Tab Displays the information the terminal uses to identify itself to other devices.
6 - 9 Cer tificates The Certificates option shows you the certif icates recognized by the operating system. ClearT ype T uner This system setting enables you to adjust the level ClearType font rendering by moving a slider. The sample text displays the setting results immediatel y.
6 - 10 Encryption Encryption gives you the option of encrypting files pl aced on storage cards so that those files cannot be read by any other device. Error Reporting Error Reporting gives you the option of enabling or disabling the error reporting function of Windows Mobile 6.
6 - 11 Memory The Memory system setting displays capacity and usage statistics for both RAM (volatile) and IPSM/ Storage Card (non-volatile) memory. Access this se tting whenever you receive system messages about memory. You cannot change the terminal’s memory allocation in the Memory system setting.
6 - 12 Po w e r Power system settings contains two tabs: Battery and Advanced. Note: You can also set automatic turn-off times for the terminal to conserve power. When the terminal is “turned off,” that means that it goes into suspend mode; see Suspend Mode on page 3-18.
6 - 13 Regional Settings Regional Settings enables you to customize the appe arance and formatting to your geographic region. Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using the $ or € € symbol), time, and date.
6 - 14 Screen The Screen system setting contains three tabs: Alignment, Clear Type, and Text Size. Alignment T ab Y ou need to re-align the screen if tapping buttons or icons with the stylus no longer seems to work appropriately . T apping Align Screen brings up the align screen window where you are guided to tap a target se v er al times.
6 - 15 W AN Inf o When the GSM radio is active, WAN Info displays useful statistics for the radio. To verify whether or not the GSM radio is enabled, check the Dolphin Wireless Manager (see page 7-6). Windows Update Windows Update is designed to download Microsoft updates to the operating system directly from Microsoft.
6 - 16.
7 - 1 7 Comm unication Connections T ab The Connections system setting provides access to the terminal’s various wireless communication options. Note: All server-assigned IP addresses use Dynam ic Host Configuration Protocol (DHCP). Icon Setting Tapping this icon… See Page Beam Enables infr ared communication.
7 - 2 Using the IrD A P ort Using the IrDA port, you can send and receive data between the terminal and other devices equipped with infrared. This can include, but is not limited to, Windows Mobile information such as Contacts and Tasks, as well as software upgrades.
7 - 3 5. When the IrDA port finds the aligned IrDA port, it immediately starts sending the selected file. The selected device reads “Sending.” 6. When the file transfer is complete, the selected device reads “Done.” Receiving Data The Beam Setting must be set to receive for the te rminal to receive data from other infrared devices.
7 - 4 Connections Manager Microsoft’s connection manager sets up multiple netw ork connections to Internet Service Providers (ISPs) via an external modem. Do NOT enter connection parameters in the Connections Manager if: • You are using one of the on-board wireless radios to connect to a network.
7 - 5 *Proxy Server Connections If you are connected to your ISP or private network during synchronization, the terminal should download the proper proxy settings during synchronization with the PC.
7 - 6 Dolphin Wireless Manager The Dolphin Wireless Manager provides a centralized in terface that enables and disables all the on-board radios. Each radio has its own configuration progr am. The Dolphin Wireless Manager also provides shortcuts to the configuration utilities for each radio.
7 - 7 4. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON . Note: If applicable, information about the radio appears in the rectangle. Accessing Radio Configuration Utilities Each of the three radios have their own configuration utilities that you can access through the Menu .
7 - 8 ActiveSync Comm unication To synchronize data between the termi nal and the workstation, ActiveSync 4.5 or higher must be installed and configured for the appropriate communication type on the host workstation and the Dolphin terminal. Dolphin terminals ship with ActiveSync already installed.
7 - 9 Setting Up the Host W orkstation Verify that ActiveSync is configured to use the appropriate communication type by clicking File > Connection Settings . Note: You can have both USB and RS-232 selected in the software without affecting processing.
7 - 10 Installing Additional Software In addition to the default programs installed on your terminal when it is first booted up, you can install any program (created for a Windows Mobile-based device), as long as the terminal has enough memory to store the program and the program has an EXE, CAB, or DLL extension.
7 - 11 3. Depending on the program, you may need to open File Explorer on the terminal, navigate to the folder where the program is located, and tap on the program file to install it.
7 - 12 9900/9950/9951 COM P or t Assignment T able COM P ort Description COM0 Unused COM1 Serial P or t: RS-232 Connector on the bottom panel COM2 Not accessible COM3 IrD A: Serial Infrared (SIR) up t.
8 - 1 8 W orking with GSM Overview The Dolphin 9900 terminal can be configured with an integrated, embedded GSM/GPRS quad-band radio module for WWAN communication.
8 - 2 V oice and Data Comm unication Dolphin terminals with integrated GSM/GPRS radios are optimized for the following two-way voice and data communications: Voice: GSM voice data ("dial-up") Data: GPRS Class 10 Data transmissions average 40-60 Kbps (available speed depends on the wireless network carrier).
8 - 3 5. Place the SIM card door over the secu red SIM card and fasten the screws. 6. Install the battery pack and turn on the terminal. S IM C a rd I nt erf a ce S c rew s S IM C a rd D oor S IM C a .
8 - 4 Enabling the GSM Radio Be default, the GSM radio should be enabled after each hard reset. Verify the status of the radio in the Dolphin Wireless Manager. Tap Start > Settings > Connections tab > Dolphin Wireless Manager . If the Phone is set to OFF, tap the Ph one rectangle and the GSM radio enables.
8 - 5 V oice Communication You can use the Dolphin terminal as a phone over the GSM radio. A udio Modes The back panel of the 9900, 9950, an d 9951 contains both a speaker an d a microphone that you can use to send and receive audio signals over the GSM network; see Back Panel: 9900 on page 3-6.
8 - 6 Sending Calls After the number is dialed, tap Talk or use the keyboard. Note: The icon indicated that the phone is in use. Ending Calls While the phone call is live, tap End or use the physical keyboard.
8 - 7 Setup Options Tap Menu > Options . The Phone Settings tab windows appear. Phone Tab Services Tab Network Tab Establish or change a PIN on the Phone tab . F or each ser vice, the phone will read settings from the network on the SIM and displa y the av ailab le options from the carrier .
8 - 8 Data Comm unication You set up data communication via the connection s manager. The carrier on the SIM card is the ISP. System Requirements • The GSM radio must be enabled; see Enabling the GSM Radio on page 8-4. • You must have an active SIM card installed; see SIM Card Installation on page 8-2.
8 - 9 4. Enter the APN and tap Next . 5. Enter the username and password from the account and tap Finish . 6. On the Connections window, tap Manage existing connections .
8 - 10 7. Tap and hold on the connection and select Connect on the popup menu. 8. The network icon in the navigation bar indica tes the GSM radio is attempting to connect . 9. When the connection is complete, the network icon changes to: . 10. You can now send data over GSM.
8 - 11 Roaming You can select automatic or manual roaming. The Phone defaults to automatic roaming. 1. When an active SIM card is inserted in the terminal, tap Start > Settings > Personal tab > Phone . The Phone Settings window appears. 2. Select the Network tab.
8 - 12.
9 - 1 9 W orking with the Bluetooth Radio Enabling the Bluetooth Radio You enable the Bluetooth radio in the Dolphin Wireless Manager (see page 7-6). 1. Tap Start > Settings > Connections tab > Dolphin Wireless Manager . 2. Tap anywhere inside the Bluetooth rectangle and Bluetooth begins activating.
9 - 2 Connecting to Other Bluetooth Devices You need to perform a device discovery and then sele ct a discovered device and connect to it. Pairing happens as part of the connection process. 1. In the Dolphin Wireless Manager, tap Menu > Bluetooth Settings .
9 - 3 4. You are prompted to enter a passcode. If the device has a specific passcode, enter it in the Passcode field and tap Next . If the device does not have a spec ific passcode, enter one in the Passcode field and tap Next . The Bluetooth radio tries to connect with the device.
9 - 4 8. The device appears in the list on the main window. 9. After the passcodes have been accepted on both sides, you have a trusted (“paired”) connection. P airing and T rusted De vices The terminal does support pairing. Pairing happens du ring general connection setup.
9 - 5 T ypes of Devices and Services When you tap Add new device on the Devices tab, the Bluetooth radio scans for discoverable Bluetooth devices in range, which are Bluetooth devices that have been made discoverable.
9 - 6 Connecting to Bluetooth Printers 1. Make sure the Bluetooth printer is in range and set to be discoverable by other Bluetooth devices. 2. Look up the Bluetooth printer’s broadcasted ID. 3. Perform a device discovery (Tap Settings > Connections > Bluetooth > Add new device .
9 - 7 T ransferring Files 1. Tap Start > Programs > File Explorer . 2. Navigate to the file you want to transfer. 3. Tap and hold on the file and select Beam File on the popup menu. 4. The Bluetooth radio begins searching for devices. 5. Tap the device to begin sending the selected file.
9 - 8 Making the T erminal Discoverable By default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other Bluetooth devices. To make the terminal discoverable, tap the Mode tab. Select Make this device visible to other devices and tap OK .
10 - 1 10 W orking with GPS Overview The Dolphin 9900 terminal contains an integrated GPS module that allows location tracking of workers and vehicles, providing better utilization of field assets. Optional mapping and navigation software provides turn-by-turn driving directions and locati on information, allowing workers to arrive on time.
10 - 2 COM7 COM Port 7 can be set to the following baud rates: • 4 8 0 0 • 9600 (This is the default baud rate and recommended for optimal GPS functioning.) • 1 9 2 0 0 • 3 8 4 0 0 Other baud rates are not possible. The baud rate sele cted on COM7 is the actual baud rate with which the GPS will be communicating.
11 - 1 11 Dolphin HomeBase De vice Overview As the hub of your Dolphin system, the Dolphin Home Base charging and communication cradle supports both RS-232 and USB communications, which make it able to interface with the majority of PC-based enterprise systems.
11 - 2 P arts and Functions Front P anel Terminal Well Place the terminal in this well to communicate with a host device, power the terminal, and charge its battery pack. If the host device is a workstation that uses ActiveSync, synchronization begins immediately.
11 - 3 COMM LED This is the communication LED. It indicates th e status of data transfer between the Dolphin terminal and the host device. The color of this LED differs if the base is using the serial or USB port connection.
11 - 4 USB Port This USB Port is full-speed and 2.0 compliant. Using a USB cable, you can connect the base to a peripheral device, such as a workstation or printer. When the terminal is seated in the terminal well, it is connected to the peripheral device via the base.
11 - 5 Serial Connector The following diagram displays the pin diagra m of the serial connector of the base. Note: Signals referenced are for a DTE device. The base is at a right-angle to the printed circuit board (PCB). The ninth pin has a ring indicator (RI).
11 - 6 Charging the Main Battery The base powers the terminal and fully charges its main battery pack in 4.5 hours. The base contains an intelligent battery charging system that protects the battery from being damaged by overcharging. The unit senses when a battery pack is fully charged and automatically turns off the charger.
11 - 7 2. Snap the battery into place with a hinging motion. The Aux Battery LED lights orange. 3. Use the AUX Battery LED to monitor charging progress. Comm unication USB Dolphin terminals support USB communications out of the box. The base also supports USB communications via the USB port located on the back.
11 - 8 Comm unicating with the Dolphin T erminal To initiate communications between the Dolphin terminal and peripheral, complete these steps: 1. Insert the Dolphin terminal into the terminal well of the base. • The DOCK LED illuminates green. If the DOCK LE D does not illuminate, make sure that the terminal is properly seated.
11 - 9 RS-232 Pin Configuration Note: This base cannot be daisy-chained. Mounting Set the base on a dry, stable surface, such as a deskt op or workbench near an electrical outlet. Be sure to provide enough workspace with good lighting for the user to view and operate the Dolphin terminal while it is in the base.
11 - 10 Desk Mounting The DIN rail slot (7.5 X 35 mm) may be mounted on th e bottom to allow for secure desk attachment of the unit if desired. Slide the DIN rail slot along the bottom panel. Then, using the appropriate nuts and bolts, secu re the DIN rail to the desk or flat surface.
11 - 11 For any of the screws positioned so that they are going directly into dry wall, use a sheet rock anchor/ screw set such as the one listed below.
11 - 12.
12 - 1 12 Dolphin Mobile Base De vice Overview This charging and communication cradle is designed specifically for in-premise and in-transit data collection applications. It features a flexible moun ting bracket, a cigarette lighter adapter, and a power cable to adapt it to your environment.
12 - 2 Fr ont P anel The following graphic features the base with a terminal inse rted into the terminal well: Terminal Well Place the terminal in this well. Once seated, the terminal can communicate with a host device and its main battery pack begins charging.
12 - 3 Bottom P anel The power supply and RS-232 connectors ar e located on the bottom of the unit. Power Supply Connector Attach the power cable that came with the base to this connector. The base can be powered by an external DC power source of between 11 VDC to 48 VDC.
12 - 4 Charging the Dolphin T erminal The base supplies charging power to the Dolphin terminal so that the terminal can monitor the charging of its battery pack.
12 - 5 Back P anel Latch The latch sits on top of the spring arm assembly and holds the back of the terminal securely in place. The 9950/9951 version of the base co ntains a special latch to accommodate the integrated pistol-grip handle.
12 - 6 Establishing Comm unication The RS-232 interface allows the terminal to communicate to a workstation, modem, or any standard RS- 232 device using a standard serial cable and communications software.
12 - 7 RS-232 Pin Configuration Refer to this table if you w ant to make your own cables. To do so, you must determine if your host RS-232 device is: • 9-pin or 25-pin and • configured as a DCE or DTE device.
12 - 8 Serial Connector The base connector is straight to the printed circui t board (PCB). The ninth pin sends 500mA at 5V power out. This can power a peripheral device, such as a mob ile printer, as long as that peripheral device can accept 500mA at 5V.
13 - 1 13 Dolphin Char geBase Device Overview This 4-slot charging cradle that can power 4 Dolphi n terminals, and charge their main batteries in 4.5 hours.
13 - 2 P arts and Functions Front P anel Terminal Wells The base contains 4 terminals wells. Each well • Holds and charges the main battery pack of one Dolphin terminal. • Contains the companion to the I/O connector on the bottom panel of Dolphin terminals.
13 - 3 Po w e r S u p p l y The base includes a power supply that contains a po wer adapter to ensure the proper voltage. The power adapter is plugged into standard AC/DC outlets. Supplying P ower 1. Be sure the power switch on the po wer adapter is in the OFF position.
13 - 4 Inser ting and Remo ving T erminals 1. Slide the terminal into the well until the Dock LED lights solid green. 2. Charging begins immediately. Note: To remove a terminal, grasp it firm ly in your hand and lift it up and out of the terminal well.
13 - 5 Mounting This base should be mounted to a dry, stable surface. When choosing a location, always bear in mind that • The mounting location must allow users easy access to the power connector. • The base should be oriented so that users can easily read the labels.
13 - 6 Desk Mounting The DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting. Installation Hardware Screw: 3/16 in. dia x 5/8 in. long pan head screw Washer: 1/2 in. OD x 7/32 in. ID x 3/64 in. thick Nut: 3/16 in. dia 1. Slide the DIN Rail into the DIN Rail slot on the bottom panel.
13 - 7 W all Mounting You need to purchase two wall mount kits that each contain: • a mounting bracket, • t h r e e s c r e w s , a n d • six washer/nut sets. You need two kits so that you have two mounting brackets–one for each end of the device–and enough screws (4) and washer/nut sets (8).
13 - 8.
14 - 1 14 Dolphin QuadChar ger Device Overview This 4-slot charging station provides intelligent batt ery management for the Li-ion battery packs used in Dolphin terminals. The 4th slot features a battery anal yzer that completely resets a battery, then displays its remaining capacity.
14 - 2 P arts and Functions To p P a n e l Charging Slots There are 4 charging slots. Each slot holds one Li-ion battery and charges it independently of the other slots. When a battery is placed in each slot, it immediately begins charging. Charge/Analyze Slot This is the 4th slot and the only one that can be used to analyze a battery.
14 - 3 Back P anel Power Switch Toggle the power switch to tu rn the charger on and off. Power Supply Connector You attach the power supply to this connecto r.
14 - 4 Inser ting and Remo ving Battery P ac ks To insert a battery pack, place the end of the battery without the locking tab into the bottom of the charging pocket and snap the battery into place with a hing ing motion. The Status LED for that particular slot illuminates orange when the battery has been properly inserted.
14 - 5 Using the Battery Analyzer Purpose Using the Charge/Analyze slot help s you monitor the charge capacity of Li-ion batteries over time. Location The battery analyzer is located in the 4th slot - na med the Charge/Analyze slot - of the ChargeBase.
14 - 6 Mounting The charger should be on a dry, stable surface and can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall. When choosing a location, always bear in mind that • the mounting location must allow user s easy access to power switch and power connector.
14 - 7 W all Mounting Use the appropriate nuts and bolts listed above to secure the DIN rail to a wall..
14 - 8 T r oubleshooting If you encounter problems with your, refer to chart below for possible solu tions. If problems persist, please contact Honeywell Technical Support.
15 - 1 15 Customer Suppor t Pr oduct Service and Repair Honeywell International Inc. provides service for al l its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
15 - 2 For ongoing and future product quality improvement in itiatives, 9900s, 9950s, and 9951s comes equipped with an embedded device lifetime counter function. Honeywell may use li fetime counter data for future statistical reliability analysis as well as ongoi ng quality, repair and service purposes.
15 - 3 Limited W arranty Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment.
15 - 4 How to Extend Y our W arranty Honeywell International Inc. offers a variety of service plans on our hardware products. These agreements offer continued coverage for your equi pment after the initial warranty expires.
.
™ Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 99-UG Rev F 8/10.
Ein wichtiger Punkt beim Kauf des Geräts Honeywell 9950 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Honeywell 9950 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Honeywell 9950 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Honeywell 9950 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Honeywell 9950 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Honeywell 9950 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Honeywell 9950 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Honeywell 9950. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Honeywell 9950 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
