Benutzeranleitung / Produktwartung 3820 USB Kit Blanco des Produzenten Honeywell
Zur Seite of 188
™ 2020/3820/3820i Cordless System User’s Guide.
Disclaimer Honeyw ell International Inc. (“Honeywell ”) reserves the right to make changes in specifications and other inf ormation co ntained in this document without prior notice, and the reader should in all cases consult Honeyw ell to determine whether any such changes ha v e been made.
Pr oduct Agency Compliance USA FCC P art 15 Subpar t C This device complies with part 15 of th e FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interf erence received, including interference that may cause undesired operation.
cUL Statement cUL listed: CSA C22.2 No.60950-1- 03 for I.T.E product safety. Eur ope The CE marking on the product in dicates that this device is in conformity with all essential re quirements of the 1999/5/EC R&TTE Directive. In addition, complies to 2006/95/EC Low Voltage Directive, when shipped with reco mmended power supply.
If you need more information on the co llection, reuse, and recycling systems, please contact your local or regional waste administration. You may also contact your supplie r for more information on the environmental performances of this product.
Eye Saf ety Statement (LED) This device has been tested in accord ance with IEC60825-1 LED safety, and has been certified to be a Class 1 LED device. Radio T ec hnology Class II CB Scheme Certified to CB Scheme IEC 60950-1. Solids and W ater Pr otection The 3820 has a rating of IP41, immuni ty of foreign particles and dripping water.
Required Safety Labels Scanner Compliance Label locations Item Number, Serial Number and Revision Information location.
Base Compliance Label locations Item Number, Serial Number and Revision Information location.
i Chapter 1 - Getting Started About This Manual ............. ......................................... 1-1 Unpacking the System ................................................ 1-1 Models .......................... ...................................
ii Beeper and LED Sequences and Their Meaning ...... 1-14 3820/3820i LED Sequences and Their Meaning . 1-15 2020 LED Sequences and Their Meaning ........... 1-15 Basic Operation of the Cordless System ................... 1-16 System Conditions .......
iii Connecting the Base with RS-232 Serial Port ............ 2-8 RS-232 Baud Rate ................................................ 2-9 RS-232 Word Length: Data Bits, Stop Bits, and Parity ......................... ................................... 2-10 RS-232 Handshaking .
iv Output Sequence Overview ....................................... 3-10 Output Sequence Editor ...................................... 3-11 Require Output Sequence ................................... 3-11 Multiple Symbols..............................
v Message Length ................. ......................................... 6-2 Codabar ........................... ........................................... 6-3 Codabar Start / Stop Charac ters ............................ 6-3 Codabar Check Character .
vi UPC A .............................. .......................................... 6-18 UPC A Check Digit .......... .................................... 6-18 UPC A Number System ....................................... 6-19 UPC A Addenda .............
vii Korea Post Code ................... .................................... 6-32 Korea Post Message Length ............................... 6-32 PosiCode A and B ..................................................... 6-32 PosiCode Message Length ......
viii Menu Command Syntax ........... ................................. 10-1 Query Commands ............. ................................... 10-2 Concatenation of Multiple Commands ................. 10-2 Responses ..................... ...............
ix Product Service and Repair .. .................................... 13-2 Online Product Service and Repair Assistance ... 13-2 Limited Warranty .................... ................................... 13-3 Appendix A - Reference Charts Symbology Chart .
x.
1 - 1 1 Getting Star ted About This Manual This manual contains inf or mation to he lp you set up , operate, and program the cordless system. Product specifications , connector pinouts , a troubleshooting guide, and customer support information are also provided.
1 - 2 Cor dless System: Main Components About the Battery Use only the Li-ion batter y packs pro v ided by Honeyw ell. Use of any batter y not sold/manuf actured by Honeyw ell ma y result in damage not cov ered by the warranty .
1 - 3 Battery Recommendations • Batteries are shipped approximately 30% to 60% charged and should be fully charged for maximum charge capacity. • The battery is a lithium ion cell and ca n be used without a full charge, as well as can be charged without fully discharging, without impacting the battery life.
1 - 4 Base Charge Mode In order f o r the batter y to be charged, there must be enough v oltage for the cir- cuitr y to work. There are three condit ions during which power can be supplied to the base.
1 - 5 Linking Image Scanner to Base When newly shipped or def aulted to fact ory settings, the base and image scan- ner are not linked. Once the image scan ner is placed into the base , the soft- ware automatically links the image scanner and the ba se .
1 - 6 Single Image Scanner Operation There are two link modes to accommoda te diff erent applications: Locked Link Mode and Open Link Mode. Scan the appropriate barcodes included in the Open Link and Lock ed Link Mode explanat ions that f ollow to switch from one mode to another .
1 - 7 Multiple Image Scanner Operation T o put the image scanner in multiple image scanner mode, scan the barcode below . Once you scan this barcode, th e image scanner is unlinked from the base and must be placed into the base to re-link. Note: Multiple Image Scanner Operation M ode allows you to link up to 7 image scanners to one base.
1 - 8 Changing Image Scanner Name - via Barcodes If you w anted to set up your image scanners with names 0001-0007, you ma y scan the barcodes below . Scan the Reset barcode after each name change and wait f or the image scanner to re-link to the base before scanning the ne xt barcode to name the ne xt image scanner .
1 - 9 Image Scanner Repor t Scan the barcode below to generate a report for the connected image scanners. The repor t indicates the por t, work gr oup, image scanner name , and address. Application W ork Gr oups Y our cordless system can have up to se ve n image scanners link ed to one base.
1 - 10 Application W ork Gr oup Selection This programming selection allo ws you to assign an image scanner to a work group b y scanning the barcode below . Y o u may then prog ram the settings (e.g., beeper volume , prefix/suffix, data form atter) that your application requires.
1 - 11 Resetting the Standar d Product Default Settings: Current Application W ork Group If you aren’t sure what prog ramming opti ons are in your image scanner , or you’v e changed some options and want the standard product default settings restored, scan the Standard Pr oduct Default Se ttings: Current Application Group barcode below .
1 - 12 Using the Image Scanner with Bluetooth Devices The 3820/3820i image scann er may be used either with the 2020 base or with other Bluetooth de vices. Scanning the Non-Base Bluetooth Connection bar- code below allows the image scanner to be used with other Bluetooth de vices (e.
1 - 13 and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the bac k cover , then scanning Save . Def ault = 0 sec (no alarm). Note: If you are out of range when you scan a barcode, you will receive an error beep even if you do not have the al arm set.
1 - 14 Batch Mode T ransmit Delay Sometimes when accumulated scans are s ent to the host system, the transmis- sion of those scans is too f ast f or the application to process. T o program a transmit dela y between accumulated scans, scan one of the f ollowing dela ys.
1 - 15 3820/3820i LED Sequences and Their Meaning 2020 LED Sequences and Their Meaning The base contains a red LED that indicates the status of the unit and verifies its communication with the host system and a green LED that indicates image scanner batter y charge condition.
1 - 16 The tables below list the indication and cause of the LED illumination and beeps for the 2020. Note: Charging only occurs with external power applied to the 2020 or 12 volt Host power. Basic Operation of the Cor dless System Cordless Base The cordless base provides the link between the cordless image scanner and the host system.
1 - 17 RF (Radio Frequency) Module Operation The cordless system uses a state-of-the-a r t two-wa y Bluetooth radio to transmit and receive data betw een the image scanner and the base.
1 - 18 Out of Range and Back into Range with Data Accumulation Mode On The image scanner ma y store a number of symbols (approximately 500 UPC symbols, others ma y vary) when out of range and then send them to the base when back in r ange.
1 - 19 2. Disconnect the keyboard cable from the back of the terminal/computer. 3. Connect the appropriate interface cable to the base and to the terminal/ computer and keyboard. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface.
1 - 20 Reading T echniques The image scanner has a view finder that projects a bright red aiming beam that corresponds to its horizontal field of vi ew . The aiming line should be centered horizontally ov er the barcode; it will not read if the aiming line is in any other direction.
1 - 21 Plug and Play Plug and Pla y barcodes provide instan t image scanner set up f or commonly used interf aces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
1 - 22 W and Emulation Plug & Pla y In W and Emulation mode, the image sc anner decodes the barcode then sends data in the same f o rmat as a wand sca nner .
1 - 23 Each barcode abov e also programs the f ollowing suffixes f or each symbology: * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR- 1, and IBM 4683 Port 17 Interfac.
1 - 24 Fo r additional USB programming and tech nical inf or mation, refer to Hone ywell “USB Application Note, ” av ailable at www.honeywell.com/aidc . Note: Without using the 9-volt extern al, power supply, the base only uses enough power from the host to op erate the interface.
1 - 25 USB HID Scan the f ollowing code to progr am th e 3820/3820i for USB HID barcode scan- ners. Scanning this code ch anges the terminal ID to 131. USB Com P or t Emulation Scan the f ollowing code to progr am th e 3820/3820i to emulate a regular RS- 232-based Com P or t.
1 - 26 ACK/NAK Mode Connecting the Base with Serial W edge The 2020 uses TTL signal le vels to w edge into an RS-232 ser ial network. Use only 2020 serial wedge cables to pr e vent damage to the base . Ref er to Con- necting the Base with RS-232 Serial Port on page 2-8 to set the baud rate and communications protocol.
1 - 27 5. Plug the other serial connector into the other device connection and tighten the two screws. 6. Plug the power supply barrel connect or to the base, and plug the power supply into the AC source. 7. Once the base has been fully connected, power up the computer.
1 - 28.
2 - 1 2 T erminal Interfaces T erminal ID If your interf ace is not a standard PC A T , ref er to "Supported Terminals" on page 2-2 through page 2-3 , and locate the T er minal ID number f or your PC.
2 - 2 Suppor ted T erminals Te r m i n a l Model(s) T erminal ID DEC VT510, 520, 525 (PC style) 005 DEC VT510, 520, 525 (DEC style LK411) 104 Esprit 200, 400 005 Heath Zenith PC, A T 003* HP V ectra 0.
2 - 3 * Default for 2020-5BE. **It is best to use the Plug and Play barcodes, beginning on page 1-24 to program these interfaces, rather than scanning the terminal ID listed in this table.
2 - 4 Ke yboard Country Scan the appropriate countr y code belo w to program the k eyboard f o r your countr y . As a general r ule, the f ollow ing characters are suppor ted, but need special care f .
2 - 5 Keyboard Country (continued) Latin America Norway Poland Portugal Romania Russia SCS Slovakia Italy Netherlands (Dutch) Spain Sweden Switzerland (German) Turkey Q U.
2 - 6 Please ref er to the Honeyw ell website ( www.honeywell.com/aidc ) f or complete ke yboard countr y suppor t inf or mation and ap plicable interf aces.
2 - 7 Emulate External K eyboard should be scanned if you do not ha ve an e xter nal ke yboard (IBM A T or equivalent). Note: After scanning the Emulate External Keyboard barcode, you must power cycle your computer. Ke yboard Modifier s This modifies special ke yboard feat ures, such as CTRL+ ASCII codes and T urbo Mode.
2 - 8 A utomatic Direct Connect Mode: This selection can be used if you ha ve an IBM A T style ter minal and the sy stem is dropping characters. Def ault = Off Connecting the Base with RS-232 Serial P ort 1. Turn off power to the terminal/computer. 2.
2 - 9 5. Once the base has been fully connected, power up the computer. All communication parameters betw een the image scanner and terminal must match f or correct data tran sf er through the ser ial por t using RS-232 protocol.
2 - 10 RS-232 W or d Length: Data Bits, Stop Bits, and P arity Data Bits sets the word length at 7 or 8 bits of data per character . If an applica- tion requires only ASCII He x characters 0 through 7F decimal (te xt, digits, and punctuation), select 7 data bits.
2 - 11 transmission, the host sends the XON ch aracter (DC1, he x 11). Data transmis- sion continues where it left off when XOFF was sent. Def ault = R TS/CTS, XON/ XOFF and A CK/NAK Off.
2 - 12 Commands ma y be strung together to cr eate custom response sequences. An e xample of a command string is listed below . 0<ESC>4<ESC>5<ESC>6, The abov e example will make an image scanner in application work group zero beep low , medium, high.
2 - 13 2020 Host Escape Commands Command Action <ESC> a Indicate as if successful menu change made <ESC> b Indicate as if unsu ccessful menu change made <ESC> 1 Illuminate green LED f or 1 35 milliseconds (followed b y at least 70 mSecs.
2 - 14 Wa n d E mu l a t i o n W and Emulation Connection The W and Emulation Connection barcodes should be used if you want to change the terminal ID only , without changing any ot her image scanner set- tings. W e recommend using Wand Em ulation Plug & Play barcodes to progr am your image scanner to emulate a w and reader .
2 - 15 W and Emulation T ransmission Rate The transmission rate is limited b y the te r minal’ s ability to receive data without dropping characters. Def ault = 25 inches/second. W and Emulation P olarity The P olarity can be sent as standard wi th black bars high, or re versed with white bars high.
2 - 16 W and Emulation Data Bloc k Siz e This transmits the data in smaller b l ocks to pre vent b uffer ov erflow . Def ault = 40 . W and Emulation Dela y Between Blocks This sets the dela y time between data b l ocks .
3 - 1 3 Output Image Scanner Functions Good Read Indicators Beeper – Good Read The beeper may be programm ed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible.
3 - 2 Beeper Pitch – Good Read The beeper pitch codes mo dify the pitch (frequency ) of the beep the image scanner emits on a good read. Def ault = Medium. Beeper Duration – Good Read The beeper duration codes modify the le ngth of the beep the image scanner emits on a good read.
3 - 3 Good Read Dela y This sets the minimum amount of ti me before the image scanner can read another barcode. Default = 0 ms (No Delay. ) User-Specified Good Read Dela y If you want to set your own .
3 - 4 Read Time-Out (Serial Trigger Mode) Use this selection to set a time-out (in milliseconds) of the image scanner’s trigger when using serial commands to trigger the image scanner. Once the image scanner has timed out, you can ac tivate the image scanner either by pressing the trigger or using a serial trigger command.
3 - 5 If there are no trigger pulls during th e “image scanner power time-out timer” interval, the image scanner goes into power down mode. Whenever the trigger is enabled, the “image scanner power time -out timer” is reset.
3 - 6 Hands Free Time-Out The Automatic Trigger and Presentation Modes are referred to as “hands free” modes. If the image scan ner’s trigger is pulled wh en using a hands free mode, the image scanner changes to manual trigger mode. You can set the time the image scanner should remain in manual trigger mode by setting the Hands Free Time-Out.
3 - 7 Centering W indow Use the centering feature to narrow the image scanner’s field of view so the image scanner reads only the barcode you want. When centering is turned on, the image scanner only read s codes that intersect or are contained within the centering window you set up.
3 - 8 Example: If you have two barcodes next to one another and the centering window is set to 40% left edge and 60% right edge, only the barcode that intersects th at window will be decoded.
3 - 9 High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Chart on page A-1, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back cover).
3 - 10 Output Sequence Overview Require Output Sequence When turned off, the barcode data will be output to the host as the image scanner decodes it. When tu rned on, all output data must conform to an edited sequence or the image sca nner will not transmit the output data to the host device.
3 - 11 5. End Output Sequence Editor Scan F F to enter an Output Sequence fo r an additional symbology, or Save to save your entries. Other Programming Selections • Discard This exits without saving any Output Sequence changes.
3 - 12 Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example.
3 - 13 To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length.
3 - 14 No Read With No Read turned On , the image scanner sends an “NR” to the host if you pull and release the trigger without readi ng a code (e.
4 - 1 4 Data Editing Prefix/Suffix Overview When a barcode is scanned, additional in f ormation is sent to the host computer along with the barcode data. This group of barcode dat a and additional, user-defined data is called a “message stri ng. ” The selections in this section are used to build the user-defined data into the message string.
4 - 2 Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252) on page A-2, for the prefix or suffix you wish to enter. Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 6.
4 - 3 Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9 , 9 for all symbologies. Y our change is automatically saved. T o Add a Carriage Return Suffix to All Symbologies Scan the f ollowing barcode if y ou wish to add a carr iage retur n suffix to all sym- bologies at once.
4 - 4 Suffix Selections Function Code T ransmit When this selection is enabled and f unction codes are contained within the scanned data, the image scanner transmits the function code to the terminal. Char ts of these function codes are provided in Supported Interface Keys star t- ing on page 7-3 .
4 - 5 Interc haracter Delay An intercharacter dela y of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Inter character Delay barcode belo w , then scan the nu mber of milliseconds and the SA VE bar- code using the Programming Chart inside the back co ver of this man ual.
4 - 6 Interfunction Delay An interfunction dela y of up to 495 mi lliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay barcode belo w , then scan the number of milliseconds and the SA VE bar- code using the Programming Chart inside the back co ver of this manual.
5 - 1 5 Data Formatting Data Format Editor Intr oduction Y ou may use the Data F or mat Editor to change the image scanner’ s output. For e xample, y o u can use the Data F ormat Editor to inser t characters at cer tain points in barcode data as it is scanned.
5 - 2 Step 4. Code I.D. In the Appendix A , find the symbology to wh ich you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual. Step 5.
5 - 3 ASCII Conversion Char t (Code Page 1252) on page A-2, and nn is the numeric value (00-99) for the number of times it should be sent.) E9 Send all but the last “nn” characters, starting from the current cursor posi- tion.
5 - 4 ters to be replaced and xx 2 defines replacement characters, continuing through zz 1 and zz 2 . E5 Terminates character replacement. Syntax = E5 . FE Compare character in current cursor pos ition to the character “xx.” If char- acters are equal, increment cursor.
5 - 5 When Data F ormatter is required, all i nput data must conf or m to an edited for- mat or the image scanner does not transm it the input data to the host de vice. Alternate Data Formats Alternate formats allow you “single shot ” capability to scan one barcode using a diff erent data f ormat than your primar y format.
5 - 6.
6 - 1 6 Symbologies Intr oduction This programming section contains the f ollowing menu selections. Ref er to Chapter 10 f o r settings and def aults. All Symbologies If you w ant to decode all the symbologi es allowab le for y our image scanner, scan the All Symbologies On code.
6 - 2 Message Length You are able to set the valid reading length of some of the barcode symbologies. If the data length of the scanned barcode doesn’t matc h the valid reading length, the image scanner will issue an error beep.
6 - 3 Codabar <Default All Codabar Settings> Codabar Codabar Start / Stop Characters Star t/Stop characters identify the leading and trailing ends of the barcode. Y ou ma y either transmit, or not transmit Start/Stop characters. Def ault = Don’t T ransmit .
6 - 4 When Check Char acter is set to V alidate, but Don’t T ransmit , the unit will only read Codabar barcodes printed with a check character , but will not transmit the check char acter with the scanned data. Codabar Concatenation Codabar suppor ts symbol concatenation.
6 - 5 Codabar Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information. Minimum and Maximum lengths = 2-60.
6 - 6 Code 39, continued Code 39 Check Character No Check Character indicates that the image scanner reads and tr ansmits barcode data with or without a check char acter .
6 - 7 Code 39, continued Code 39 Append This function allows the image scanner to append the data from se veral Code 39 barcodes together bef o re transmitti ng them to the host computer .
6 - 8 Full ASCII If Full ASCII Code 39 decoding is enab led, certain character pairs within the barcode symbol will be inter preted as a sing le character . F or e xample: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.
6 - 9 Code 39 Code P age Code pages define the mapping of charac ter codes to characters. If the data received does not displa y with the proper characters, it ma y be because the bar- code being scanned was created using a code page that is diff erent from the one the host program is e xpecting.
6 - 10 When Check Digit is set to V alidate and T ransmit , the image scanner only reads Interleav ed 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Def ault = No Check Digit. Interleaved 2 of 5 Message Length Scan the barcodes below to change the message length.
6 - 11 Code 93 < Default All Code 93 Settings > Code 93 Code 93 Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
6 - 12 Straight 2 of 5 Industrial (three-bar star t/stop) <Default All Straight 2 of 5 Settings> Straight 2 of 5 Industrial Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation.
6 - 13 S traight 2 of 5 IA T A, continued Straight 2 of 5 IA T A Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
6 - 14 Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation.
6 - 15 Code 1 1, continued Code 11 Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information.
6 - 16 Code 128, continued ISBT 128 Concatenation In 1994 the International Society of Blood T ransfusion (ISBT) ratified a standard f or communicating critical blood inf or mat ion in a uniform manner . The use of ISBT f o rmats requires a paid license.
6 - 17 Code 128 Function Code T ransmit By def ault, Code 128 function codes are not transmitted with Code 128 barcode data. Howe ver , if you wish to transm it Code 128 function codes with the bar- code data, scan the Function Codes On barcode, belo w .
6 - 18 T elepen Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation. Minimum and Maximum lengths = 1-60.
6 - 19 UPC A Number System The numeric system digit of a U .P .C. sy mbol is normally transmitted at the beginning of the scanned data, but the unit can be progr ammed so it will not transmit it. Def a ult = On. UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data.
6 - 20 UPC A Addenda Separator When this f eature is on, there is a sp ace between the data from the barcode and the data from the addenda. When turned off, there is no space. Def ault = On. UPC-A/EAN-13 with Extended Coupon Code Use the f ollowing codes to enab le or disable UPC-A and EAN-13 with Extended Coupon Code.
6 - 21 UPC E0 and UPC E1 Most U .P .C . barcodes lead with the 0 nu mber system. F or these codes, use the UPC E0 selection. If you need to read codes that l ead with the 1 number sys- tem, use the UPC E1 selection. Def ault = On (UPC E0) and Off (UPC E1).
6 - 22 UPC E0 and UPC E1 Addenda Separator When this f eature is on, there is a sp ace between the data from the barcode and the data from the addenda. When turned off, there is no space. Def ault = On. UPC E0 Check Digit Check Digit specifies whether the chec k di git should be transmitted at the end of the scanned data or not.
6 - 23 UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Def ault = Off f or both 2 Digit and 5 Digit Addenda. EAN/J AN 13 <Default All EAN/JAN Settings> EAN.
6 - 24 EAN/JAN 13 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Def ault = Off f o r both 2 Digit and 5 Digit Addenda. EAN/JAN 13 Ad denda Required When Addenda Required is set to on, the image scanner wi ll only read EAN/ JAN 13 barcodes that ha ve addenda.
6 - 25 ISBN T ranslate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN n umber format. Def ault = Off. EAN/J AN 8 <Default All EAN/JAN 8 Settings> EAN/J.
6 - 26 EAN/JAN 8 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Def ault = Off f o r both 2 Digit and 5 Digit Addenda. EAN/JAN 8 Ad denda Required When Addenda Required is set to on, the image scanner wi ll only read EAN/ JAN 8 barcodes that ha ve addenda.
6 - 27 MSI <Default All MSI Settings> MSI MSI Check Character Different types of check characters are used with MSI barcodes. You can program the image scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit.
6 - 28 Plessey Code <Default All Plessey Code Settings> Plessey Code Plessey Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation. Minimum and Maximum lengths = 4-48.
6 - 29 GS1 DataBar Omnidirectional GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > *.
6 - 30 GS1 DataBar Expanded GS1 DataBar Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
6 - 31 China P ost Code <Default All China Post Code Settings> China P ost Code China P ost Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information. Minimum and Maximum lengths = 2-80.
6 - 32 K orea P ost Code <Default All Korea Post Code Settings> K orea P ost Code K orea Post Messa g e Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation. Minimum and Maximum lengths = 2-80.
6 - 33 Y ou have to ha ve P osiCode A and B on to read any of the P osiCode symbolo- gies. P osiCode Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information. Minimum and Maximum lengths = 2-80.
6 - 34 Codabloc k F <Default All Codablock F Settings> Codabloc k F Codabloc k F Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional info rmation. Minimum and Maximum lengths = 1-2048.
6 - 35 Code 16K Code 16K Message Length Scan the barcodes below to chan ge the message length. Refer to Message Length on page 6-2 for additi onal information.
6 - 36 Code 49 Message Length Scan the barcodes below to change the message length. Refer to Message Length on page 6-2 for additional inform ation. Minimum and Maximum lengths = 1-81.
7 - 1 7 Interface K e ys Ke yboard Function Relationships The f ollowing K eyboard Function Code , Hex/ASCII V alue, and Full ASCII “CTRL ”+ relationships apply to all ter m inals that can be us ed with the image scanner . Refer to page 2-7 enab le Control + ASCII mode.
7 - 2 The last five char acters in the Full ASC II “CTRL ”+ column ( [ ] 6 - ), apply to US only . The f ollowing char t indicates th e equivalents of these fiv e characters f or different countries.
7 - 3 Suppor ted Interface Ke ys ASCII HEX IBM A T/XT and PS/2 Compatibles, WYSE PC/A T Supported Keys IBM XT s and Compatibles Supported Keys IBM, DDC, Memorex T elex, Harris* Supported Keys NUL 00 R.
7 - 4 Suppor ted Interface Ke ys ASCII HEX IBM, Memorex T elex (102)* Supported Keys Memorex T elex (88)** Supported Keys NUL 00 Reserved Reserved SOH 01 Enter Enter STX 02 F11 PF10 ETX 03 F12 PF11 EO.
7 - 5 Suppor ted Interface Ke ys ASCII HEX Esprit 200, 400 ANSI Supported Keys Esprit 200, 400 ASCII Supported Keys Esprit 200, 400 PC Supported Keys NUL 00 Reserved Reserved Reserved SOH 01 New Line .
7 - 6 Suppor ted Interface Ke ys ASCII HEX Apple Mac/iMac Supported Keys NUL 00 Reserved SOH 01 Enter/Numpad Enter STX 02 CAPS ETX 03 ALT make EOT 04 ALT break ENQ 05 CNTRL make ACK 06 CNTRL break BEL.
8 - 1 8 Utilities T o Add a T est Code I.D . Prefix to All Symbologies This selection allows y ou to tur n on transmission of a Code I.D . bef ore the decoded symbology . (See the Symbology Chart , page A-1) f or the single char- acter code that identifies each symbology .
8 - 2 Image Scanner Repor t Scan the barcode below to generate a report for the connected image scan- ners. The report indicates the por t, work group , image scanner name, and address. T o assign a name to your image scanner , refer to "Menu Command Syntax" on page 10-1.
8 - 3 Resetting the Standar d Pr oduct Default Settings: All Application W ork Groups The f o llowing barcode def aults all of th e work groups to the factory settings. The Menu Commands star ting on page 10-6 list the standard product default settings f or each of the co mmands (indicated by an asterisk (*) on the program- ming pages).
8 - 4.
9 - 1 9 Visual Xpress Visual Xpress Intr oduction Visual Xpress provides a wide range of PC-based prog ramming functions that can be perf ormed on an imager connect ed to your PC's COM port.
9 - 2 Installing Visual Xpress from the W eb Note: Visual Xpress requires .NET software. If .NET is not installed on your PC, you will be prompted to install it duri ng the Visual Xpress installation. 1. Access the Honeywell web site at www.honeywell.
10 - 1 10 Serial Pr ogramming Commands The serial programming commands can be used in place of the programming barcodes. Both the serial commands and the programming barcodes will pro- gram the 2020. F or complete descriptio ns and examples of each serial pro- gramming command, ref er to the corres ponding programming barcode in this manual.
10 - 2 Data The new value for a menu settin g, identified by the Tag and Sub- Tag. Storage A single character that spec ifies the storage table to which the command is applied. An exclamation point ( ! ) performs the com- mand’s operation on the de vice’s volatile menu configuration table.
10 - 3 Responses The de vice responds to serial commands with one of three responses: AC K Indicates a good command which has been processed. ENQ Indicates an inv alid T ag or SubT ag command. NAK Indicates the command was good, b u t th e Data field entr y was out of the allow able range f or this T ag and SubT ag co mbination, e.
10 - 4 Example #4: What are the device’s se ttings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK].
10 - 5 The Menu Commands star ting on page 10-6 list the factory default settings f or each of the commands (indica ted by an asterisk (*) on the programming pages). Note: Scanning this barcode also causes both the image scanner and the base to perform a reset and beco me unlinked.
10 - 6 Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entr y Pag e Base Charge Mode *A utomatic BASCHG1 1-4 Full Charge Rate BASCHG2 1-4 Low Charge Rate BASCH.
10 - 7 Out-of-Range Alarm Base Alarm Duration (Range 1 - 3000 sec (*0)) BASORD 1-13 Image Scanner Alarm Duration (Range 1 - 3000 sec (*0)) BT_ORD 1-13 Alarm Sound T ype Base Alar m T ype BASORW 1-13 I.
10 - 8 Program K eyboard Countr y *U .S.A. KBDCTY0 2-4 Belgium KBDCTY1 2-4 Brazil KBDCTY16 2-4 Canada (F rench) KBDCTY18 2-4 Czech Repub lic KBDCTY15 2-4 Denmark KBDCTY8 2-4 Finland (Sweden) KBDCTY2 2.
10 - 9 K eyboard Style *Regular KBDSTY0 2-6 Caps Lock KBDSTY1 2-6 Shift Lock KBDSTY2 2-6 A utomatic Caps Lock KBDSTY6 2-6 Emulate External Key b o a r d KBDSTY5 2-7 K eyboard Modifiers *Control + ASCI.
10 - 10 W ord Length: Data Bits, Stop Bits , and Pa r i t y 7 Data, 1 Stop , Parity Even 232WRD3 2-10 7 Data, 1 Stop , Parity None 232WRD0 2-10 7 Data, 1 Stop , Parity Odd 232WRD6 2-10 7 Data, 2 Stop .
10 - 11 W and Emulation P olar- ity *Black High WNDPOL0 2-15 White High WNDPOL1 2-15 W and Emulation Idle Idle Lo w WNDIDL0 2-15 *Idle High WNDIDL1 2-15 W and Emulation Data Block Siz e 20 WNDBLK0 2-1.
10 - 12 Number of Beeps - Good Read *1 BEPRPT1 3-2 Range 1 - 9 BEPRPT# 3-2 Good Read Dela y *No Delay DL YGRD0 3-3 Shor t Delay (500 ms) DL YGRD500 3-3 Medium Dela y (1000 ms) DL YGRD1000 3-3 Long Del.
10 - 13 Centering Centering On DECWIN1 3-7 *Centering Off DECWIN0 3-7 Left of Centering Win- dow *40 DECLFT### 3-7 Right of Centering Win- dow *60 DECRGT### 3-7 Pref erred Symbology On PRFENA1 3-8 *Of.
10 - 14 Suffix Add Suffix SUFBK2## 4-4 Clear One Suffix SUFCL2 4-4 Clear All Suffix es SUFCA2 4-4 Function Code T rans- mit *Enable RMVFNC0 4-4 Disable RMVFNC1 4-4 Intercharacter Dela y DL YCHR## 4-5 .
10 - 15 Codabar Star t/Stop Char . * Don’t T ransmit CBRSSX0 6-3 T ransmit CBRSSX1 6-3 Codabar Check Char . * No Chec k Char . CBRCK20 6-4 V alidate, But Don’t T ransmit CBRCK21 6-4 V alidate, and.
10 - 16 Interleave d 2 of 5 Off I25ENA0 6-9 *On I25ENA1 6-9 Interleav ed 2 of 5 Check Digit * No Check Char . I25CK20 6-10 V a lidate, But Don’t Tr a n s m i t I25CK21 6-10 V alidate, and T ransmit .
10 - 17 Matrix 2 of 5 Message Length Minimum (1 - 80) *4 X25MIN## 6-14 Maximum (1 - 80) *80 X25MAX## 6-14 Code 11 Def ault All Code 11 Settings C11DFT 6-14 Code 11 *Off C11ENA0 6-14 On C11ENA1 6-14 Co.
10 - 18 UPC A Def ault All UPC A Settings UP ADFT 6-18 UPC A Off UP AENA0 6-18 *On UP AENA1 6-18 UPC A Check Digit Off UP ACKX0 6-18 *On UP ACKX1 6-18 UPC A Number Sys- tem Off UP ANSX0 6-19 *On UP AN.
10 - 19 UPC E 5 Digit Addenda *Off UPEAD50 6-23 On UPEAD51 6-23 UPC E Addenda Required *Not Required UPEARQ0 6-21 Required UPEARQ1 6-21 UPC E Addenda Separator Off UPEADS0 6-22 *On UPEADS1 6-22 EAN/JA.
10 - 20 EAN/JAN 8 5 Digit Addenda *Off EA8AD50 6-26 On EA8AD51 6-26 EAN/JAN 8 Addenda Required *Not Required EA8ARQ0 6-26 Required EA8ARQ1 6-26 EAN/JAN 8 Addenda Separator Off EA8ADS0 6-26 *On EA8ADS1.
10 - 21 GS1 DataBar Expanded Def a ult All GS1 DataBar Expanded Settings RSEDFT 6-30 GS1 DataBar Expanded Off RSEENA0 6-30 *On RSEENA1 6-30 GS1 DataBar Expanded Msg.
10 - 22 Po s i C o d e O f f P O S E N A 0 6-32 *On POSENA1 6-32 A and B On POSLIM0 6-33 A and B and Limited A On POSLIM1 6-33 *A and B and Limited B On POSLIM2 6-33 P osiCode Msg.
10 - 23 A uto Reconnect Mode *On BT_ACM1 B-1 Off B T_A C M0 B-1 Maximum Link Attempts *0 (0 - 100) BT_MLA### B-2 Relink Time-Out *3 (1 - 100) BT_RL T### B-3 Selection Setting * Indicates default Seria.
10 - 24.
11 - 1 11 Pr oduct Specifications 3820 Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 6.2 inches (15.7 cm) Length 5.3 inches (13.
11 - 2 3820i Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 6.5 inches (16.5 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.
11 - 3 2020-5BE Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.
11 - 4 2020-CBE Pr oduct Specifications P arameter Specification Dimensions (T ypical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.
11 - 5 S t andard Cable Pinouts Keyboard W edge 10 Pin RJ41 Modular Plug connects to the base 1 2 Cord shield 3 Tied to supply power 4 Supply ground 5 Terminal clock 6 Terminal data 7 Supply power input (Refer to tables on page 11-3 .
11 - 6 S tandard Cable Pinout s Wa n d E m u l a t i o n 10 Pin Modular Plug connects to the base 1 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 6 Barcode data output 7 Supply power input (Refer to tables on page 11-3 .
11 - 7 S t andard Cable Pinouts Serial Output 10 Pin RJ41 Modular Plug connects to the base 1 2 Cord shield 3 Prog 1 (Tied to supply power for primary cable) 4 Supply ground 5 Receive data - Serial data to image scanner 6 Transmit data - Serial data from image scanner 7 Supply power input (Refer to tables on page 11-3 .
11 - 8 S tandard Cable Pinout s USB 10 Pin Modular Plug connects to the base 1 2 Data + 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data -.
12 - 1 12 Maintenance Maintenance Repairs and/or upgrades are not to be perf or med on this product. These ser- vices are to be perf or med only by an authorized ser vice center . See "Customer Support" on page 13-1 for further information. Cleaning the Device Reading perf ormance may degrade if the image scanner’ s window is not clean.
12 - 2 Replacing the 2020 Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the base’s cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip.
12 - 3 • The power cable is connected proper ly and there is power at the power source. • The host system power is on (if external power isn’t used). Is the green LED on? If the gree n LED isn’t illuminated, check that: • The image scanner is co rrectly placed in the base.
12 - 4 The image scanner won’t re ad your barcode at all. 1. Scan the sample barcodes in the back of this manual. If the image scanner reads the sample barcodes, check that your barcode is readable. Verify that your barcode symbology is enabled (see Chapter 6 ).
13 - 1 13 Customer Suppor t T echnical Assistance If you need assistance installing or trou bleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 Fax number: (315) 554-6705 E-mail: natechsupport@handheld.
13 - 2 Pr oduct Service and Repair Honeywell provides service for all it s products through service centers throughout the world. To obtain warrant y or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
13 - 3 Limited W arranty Honeyw ell International Inc. ("Honeywell") warr ants its products to be free from def e cts in materials and workmanship and to conf or m to Honeywell’ s published specifications applicable to the products purchased at the time of shipment.
13 - 4 AG ES, SO THE ABO VE LIMIT A TION OR EXCLUSION MA Y NO T APPL Y T O YO U . All provisions of this Limited W arran ty are separate and se verab le, which means that if any pro vision is held in v alid and unenforceab le, such deter mina- tion shall not aff e ct the validity of enf orc eability of the other provisions hereof .
A - 1 A Referenc e Char ts Symbology Char t Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Iden tifiers, for AIM modifier character details. Note: Prefix / Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry.
A - 2 ASCII Con version Chart (Code P age 1252 ) Note: This table applies to U.S. style keyboa rds. Certain characters may differ depending on your Country Code/PC regional settings.
A - 3 Dec. Hex Char Dec. Hex Char Dec. Hex Char Dec. Hex Char 128 80 € € 160 A0 192 C0 À 224 E0 à 129 81 161 A1 ¡ 193 C1 Á 225 E1 á 130 82 ‚ 162 A2 ¢ 194 C2 Â 226 E2 â 131 83 ƒ 163 A3 .
A - 4 Code P age Mapping of Printed Barcodes Code pages define the mapping of charac ter codes to characters . If the data received does not displa y with the pr oper characters, it ma y be because the barcode being scanned was created using a code page that is diff erent from the one the host program is e xpecting.
B - 1 B Minimizing Bluetooth/ISM Band Network Ac t i vi t y The settings described below can help you customize the re-linking behavior of the cordless linear imaging system to obtain the best compromise between convenience and low interference. Note: ISM band refers to the 2.
B - 2 Maximum Link Attempts The Maximum Link Attempts setting co ntrols the number of times the image scanner tries to form a connection with a base unit or PC. During the connection setup process, the image sca nner transmits in order to search for and connect to a base unit.
B - 3 Relink Time-Out Relink Time-Out controls the idle time between re-link attempts. An attempt to link an image scanner to a ba se unit typically lasts up to 5 seconds. This is the time when the image scanner is actually attempting to contact base unit.
B - 4 Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Image Scanner Power Time-Out Timer set to 1800: Note: See Image Scanner Power Time-Out Timer on page 3-4. The image scanner attempts to connect to the base unit e very 15 seconds, measured from star t of attempt to star t of attempt.
Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN 13 1234567890 Code 128 9 780330 290951 654 EAN 8 3210 5 456123 8 0 UPC-E.
Sample Symbols Code 93 123456-9$ Straight 2 of 5 Industrial 123456 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012 Code 39 Codabar BC321 A13579B.
Programming Chart A C Save B Discard F E D Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save .
Honeywell 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 3820-UG Rev C 7/08.
Ein wichtiger Punkt beim Kauf des Geräts Honeywell 3820 USB Kit Blanco (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Honeywell 3820 USB Kit Blanco noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Honeywell 3820 USB Kit Blanco - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Honeywell 3820 USB Kit Blanco reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Honeywell 3820 USB Kit Blanco erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Honeywell 3820 USB Kit Blanco besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Honeywell 3820 USB Kit Blanco verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Honeywell 3820 USB Kit Blanco. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Honeywell 3820 USB Kit Blanco gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
