Benutzeranleitung / Produktwartung LEGACY HL120 des Produzenten Hobart
Zur Seite of 20
Models HL120 ML-134296 HL200 ML-134331 HL200 ML-134289 PRIOR ML’S COVERED IN THIS CATALOG HL200 ML-134308 INSTRUCTION MANUAL 701 S. RIDGE AVENUE TROY, OHIO 45374 -0001 937- 332- 3000 · W W W.
2 TABLE OF CONTENTS GENERAL ............................................................................................... 3 INSTALLATION ............................................................................................... 3 Unpacking ....
3 Installation, Operation and Care of Legacy TM 12 & 20-Quart Mixers SAVE THESE INSTRUCTIONS GENERAL The Legacy 12-quart mixer is a bench-type mixer which featu res a S m a r tT i me r™ , a ma nu a l b ow l lift and a #12 attach ment hub as standard equipment.
ELECTRICAL CONNE CTIONS (Cord Co nnected Mixer s) WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A THREE- PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN.
OPERATION WARNING: MOVING AGITATOR I N BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT OF BOWL WHILE IN OPERATION. DO NOT USE WIT HOUT INTERLOCKED GU ARD. The Legacy mixer is equipped with SmartTim er TM c ont rol s. Ref er to Fig. 1 for operating parts and OPERATION section for their functions.
Standard Controls Models HL120/HL200 (With Three Mix Sp eeds Plus Stir Sp eed) DISPLAY MIXING TIME STOPS MIXER STARTS MIXER TIME SELECTOR Fig. 2 SPEED SELECTOR HL120/HL200 Mixer S peeds STIR (Slow) The lowe st speed is for in corporatin g ingredients .
Recipe Timer (Optional) Models HL120/HL200 (With Three Mix Sp eeds Plus Stir Sp eed) Fig. 15 The SmartPlus2 ™ recipe timer has two operating modes, Standard (ST D) and RECIPE. Standard Mode Operates exactl y as the standard controls utilizing continuous and timed mi xing.
BOWL PLACEMENT The bowl must be insta lled before the agitator is installed. To install the bowl, lower the bowl support and po sit ion bowl so the alig nment pins on the left side of the bowl support fit in the holes in the bowl tab . (Fig. 3) Place the slotted tab on bo wl into the lower p art of the pin.
PREPARE FOR MIXING 1. Place the mixing bowl on the b owl support. 2. Pour ingredien ts into the bowl. 9 3. Swing the b owl back to the mix position. 4. Place the a gitator inside the bowl, and th en attach it to the agitator shaft (F ig. 6). 5. Lift bowl support.
Using the Count-Do wn Mode (Timed Mixi ng) 1. Turn the SPEED dial to s elect a mix sp eed. a. If the count-up mode was used for the previous batc h, the desired time needs t o be entered. b. If the count-down mode was use d for the previ ous batch, the pre vious time will be d i s p l a y e d .
RECIPE TIMER OPERATION Recipe Timer Notes • If pause is selected as a mix sp eed, the mi xer START button mus t be presse d to advance to the ne xt recipe step a fter the pause ti me has expired. • If pause has been sel ected, the bowl guard can be o pened and the ti me will continue to count down.
View Recipe When the mi xer is in RECIPE mode, you can vie w the step setti ngs of any recipe. 1. Press the SELECT/SAV E button. A. Display will alternate between spe ed and time. B. The LED of the step being d isplayed will fl ash. 2. Use the arrow buttons to view th e next step.
13 NOTES: • If a value has been assigned for a step number, that LED will be lit. • The LED for the selected step will blink. • If the default value is still assigned to a step, the LED will not be lit. • When programming, the Recipe and Time Selectors are disabled.
UNLOADING 1 . Open the bowl guard wir e cage assembly. 2 . Lower bowl support. 3 . Remove the agitator from the agitator shaft. 4. Slightly lift the bowl off the pin (right side), pull bowl t o the front and remove from the bowl support (left side).
Remove and Clea n Bowl Guard Wire C age (Fig. 11) 1. Rotate wire cage to your left until the three ca rriers align with the carrier escape slots in the circular ridge of the planet ary drip cup. 2. Lift the wire cage straight up so the carr iers escape from the slots on the drip cup.
AGITATORS AND ATTACHMENTS Attachment s for attachment h ub and agitat ors are covere d in a separate Hob art Legacy Mixer Use and App l i c a t i on H a n db o o k on t h e M i x e r O p e r at o r I n fo r m a t io n C D . F o l l ow t h e in s t r uc t i o ns accordingly.
12 & 20 Qt. P Pasty Knife 12 & 20 Qt. Ingredient Chute 12 & 20 Qt. Table CLEANING WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURES. The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it sh ou l d be washed with a clean, damp cloth.
MAINTENANCE WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY MAINTENANCE PROCEDURES. Slideway Fig. 13 Fig. 12 Planetary Seal LUBRICATION Slideways The slideways (Fig. 12) sh ould be lubricate d approximately twice a year. T o reach these areas, fully lower the bowl su pport and remove the apro n, which is secured by slott ed screws.
ADJUSTMENTS Agitator Clearance The agitator clea rance shou ld be checked p eri odically. The agit ator must not to uch the bowl and the maximum clearan ce between the bottom of th e bowl and the B flat bea ter is 1/8" ( 3 mm); the maximum clearance between the b ottom of the bowl and the ED do ugh arm is 5/16” (8 mm).
TROUBLESHOOTING Symptoms Poss ible Causes Mixer will not start Flas hing Time Dis play – Se e Below Branch circuit protector is in open position - check fuse or di sconnect swit ch. Mixer is overloaded. Wire ca ge is not in the cl osed posi tion. Bowl is not in close d (mix) position o r if Bowl in not in up position.
Ein wichtiger Punkt beim Kauf des Geräts Hobart LEGACY HL120 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hobart LEGACY HL120 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hobart LEGACY HL120 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hobart LEGACY HL120 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hobart LEGACY HL120 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hobart LEGACY HL120 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hobart LEGACY HL120 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hobart LEGACY HL120. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hobart LEGACY HL120 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
