Benutzeranleitung / Produktwartung HR7E des Produzenten Hobart
Zur Seite of 40
HR7E ROTARY OVEN N S T R U C T I O N S I 701 S. RIDGE A VENUE TROY , OHIO 45374-0001 937 332-3000 www .hobartcorp.com FORM 35511 (Feb. 2006) MODEL HR5E & HR7E ROT AR Y OVENS MODEL HR7E STAINLESS S.
– 2 – © HOBART 2006 T ABLE OF CONTENT GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation and Care of MODEL HR5E & HR7E ROT AR Y OVENS SA VE THIS MANUAL FOR FUTURE REFERENCE GENERAL The HR5E and HR7E Ovens are five-spit and seven-spit rotary ovens that feature a full view tempered glass door and quartz lighting that promote visual appeal and stimulate customer interest.
– 4 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND / OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
– 5 – ELECTRICAL DATA HR5E HR5E / HR5E * VOLTAGE HZ PHASE AMPERAGE WATTAGE AMPERAGE 208(2W) 50/60 1 26.9 6000 53.8 240(2W) 50/60 1 25.0 6000 50.0 208(3W) 50/60 3 15.5 6000 31.0 240(3W) 50/60 3 14.4 6000 28.8 220/380(4W) 50/60 3 8.4 6000 16.8 230/400(4W) 50/60 3 8.
– 6 – PLACING THE ROTOR IN THE OVEN (HR5E) The rotor must properly engage with the drive mechanism. Orient the rotor so that the end plate with the drive pin is aligned with the slotted drive hub. STEP 1: Place the drive end of the rotor shaft into the slotted drive hub (Fig.
– 7 – PLACING THE ROTOR IN THE OVEN (HR7E) The rotor must properly engage with the drive mechanism. Orient the rotor so that the end plate with square drive slots is on the same side of the oven as the drive arm. STEP 1: Stop the drive arm so it is in the down position (Fig.
– 8 – OPERA TION WARNING : HOT GLASS, GREASE AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING AND SERVICING THE OVEN. CONTROLS (Fig. 9) MAIN POWER SWITCH — Turns oven and controls on or off. PROGRAM — Enters program mode to modify a cook program; press P for 3 seconds.
– 9 – INITIAL STARTUP Power On Toggle the Main Power switch on the front panel of the oven to the ON position; the red indicator light on the switch comes on (Fig. 9). Idle Mode When the oven is first turned on, the display shows the time of day and the last operated program number.
– 10 – SAVING OR VERIFYING A COOK PROGRAM (PROGRAM 1 – 9) Begin from Idle Mode. Program display shows last operated program (0 – 9). • Select a program (1 – 9). Program 0 is Manual Mode and cannot be saved into memory. • Press P for 3 seconds to enter programming mode.
– 11 – Cooking 'Step 3' LED is lit. Time display blinks. • Enter the desired cook time from 0:01 (1 minute) to 6:00 (6 hours). • Press ENTER to accept (or, press CLEAR to void and reenter). An invalid entry produces a double beep. Entering 0:00 for the time turns step 3 off and skips to step 4.
– 12 – PROGRAMMED COOKING (Program 1 – 9) Begin from Idle Mode. The Program display shows the last operated program (0 – 9). • Select a saved cook program (1 – 9). Any programmed steps for the selected program are indicated by lit step LEDs.
– 13 – MANUAL COOKING (Program 0) Begin from Idle Mode. The Program display shows the last operated program (0 – 9). • Select manual mode by selecting program 0: [0, ENTER]. Cook Step 1 LED is lit. Time display blinks. • Enter the desired cook time from 0:01 (1 minute) to 6:00 (6 hours).
– 14 – HOLDING CYCLE (SILENCING THE 'END OF CYCLE' ALARM) After a cook cycle has been completed, the beeper sounds and the oven automatically executes the Hold cycle (Step 4 of the cooking program). The Hold cycle will not execute if it was programmed 'off', using Hold Temp = 000.
– 15 – ADDING COOK TIME • Press ADD 5 MIN during a cooking cycle to add 5 minutes of cook time to the current step of the program in process. Press during the end of cycle buzzer or during Hold cycle to add 5 minutes of cook time to the last step of the last operated program.
– 16 – SUGGESTED ROASTING GUIDELINES The suggested cooking times and temperatures in the table may require adjustment for proper doneness depending on initial product temperature, weight, size, shape and other factors.
– 17 – STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 ST.
– 18 – Bring chickens from cooler. Check temperature — range should be from 37 ° F to 42 ° F. Insert approved popper, if available; it will pop out when chicken is done. PREPARING, TYING & SPITTING — CHICKENS ON V-SPITS The rotary oven is not designed to roast frozen foods.
– 19 – INCORRECT SPITTING — CHICKENS ON V-SPITS WRONG — Angle of spit is in line with breast. This will split the backbone and could possibly result in falling off the spit during cooking. WRONG — Legs and thighs are not on same side as breast.
– 20 – WARNING : SPITS ARE SHARP. USE CARE WHEN LOADING PRODUCT. SPITTING — CHICKENS ON FORK SPITS (HR5E) Press pointed ends of spits into whole poultry so points go through the chest-wing and leg-thigh regions (Fig.10). Load three or four chickens on each fork spit.
– 21 – Fig. 15 1 Load 2 Skip 4 Skip 5 Load 6 Skip 7 Load 3 Load WARNING : SPITS ARE SHARP. USE CARE WHEN LOADING PRODUCT. SPITTING — CHICKENS ON FORK SPITS (HR7E) Press pointed ends of spits into whole poultry so points go through the chest-wing and leg-thigh regions (Fig.
– 22 – Loading V-Spits or Thermo-Wave Spits on the Rotor (HR5E) 1. Place pointed end of V-spit into outside hole on drive side of rotor (Fig. 19). 2. Fit notched end of V-spit into appropriate holes on non-drive side of rotor (Fig. 18). 3. Make sure the spit is level.
– 23 – Loading V-Spits or Thermo-Wave Spits on the Rotor (HR7E) 1. Place pointed end of V-spit into outside hole on non-drive side of rotor (Fig. 24). 2. Fit notched end of V-spit into appropriate holes on drive side of rotor (Fig. 25). 3. Make sure the spit is level.
– 24 – PERSONAL PROTECTIVE EQUIPMENT Chickens and accessories are hot. Use care during unloading by using appropriate personal protective equipment such as 18" insulated gloves, an apron, long sleeved clothing and closed toed shoes. UNLOADING ACCESSORIES FROM OVEN Opening the door does not stop the rotor, heaters or fan.
– 25 – CLEANING WARNING : DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE MACHINE AN D FOLLOW LOCKOUT / TAGOUT PROCEDURES BEFORE CLEANING OR SERVICING. Proper cleaning prolongs the life and productivity of the oven. The oven should be routinely cleaned throughout the day and thoroughly cleaned at the end of the day.
– 26 – CLEANING STAINLESS STEEL SURFACES 1. Wash stainless steel parts with warm soapy water. 2. Rinse parts thoroughly. 3. Dry with a soft clean cloth. CLEANING GUIDELINES FOR NONSTICK COA TED SURF ACES Abrasion and aggressive chemicals reduce the life of the nonstick coating.
– 27 – CLEANING QUARTZ LAMPS CAUTION: Do not clean the quartz lamps in the top of the oven with soap and water. Be very careful when cleaning lamps. Lamps can be broken by mishandling. • Clean lamps with a cloth soaked in alcohol. • Do Not touch lamps with your bare hands.
– 28 – WEEKLY CLEANING — HR5E OVENS Clean ceiling of oven interior to remove potential grease build-up. Excessive grease build-up on convection fan blade and / or vent-grate will decrease oven's cooking performance over time. NOTE: For ease of cleaning, replacement fan blade(s) are available from Hobart Service Parts.
– 29 – 4 Clean ceiling area around the elements and convection fan (Figs. 39, 40). 5. Wash vent-grate and fan blade in a sink with warm soapy water (Fig. 41). 6. Rinse and allow to dry. 7. After cleaning, reinstall fan blade by mating D-shaped fan onto D-shaped shaft and then tightening center nut counterclockwise (Fig.
– 30 – Fig. 46 WEEKLY CLEANING — HR7E OVEN WITH REAR GLASS DOOR, ACCESS FROM REAR Clean ceiling of oven interior to remove potential grease build-up. Excessive grease build-up on convection fan blade(s) and / or vent-grate will decrease oven's cooking performance over time.
– 31 – Fig. 50 Fig. 51 Fig. 52 Fig. 49 Fig. 48 3. Remove the center nut that secures the element cover using a 7 / 16 " nutdriver (Fig. 47). 4. Allow the element cover to swing down (Figs. 48, 49). 5 . Remove both fan blades. Unscrew the center nut on each fan blade (clockwise, Fig.
– 32 – 8. Clean the vent-grate and fan blades (Fig. 53). Rinse and allow to dry. 9. After cleaning, reinstall 2 fan blades: Mate D-shaped hole on fan onto D-shaped shaft; then tighten nut (counterclockwise) (Fig. 54). 10. Swing element cover up until all 3 studs protrude through cover.
– 33 – Fig. 56 11. Working from rear of oven, position high side of vent-grate toward rear of oven, short side faces center of oven (Fig. 56). 12. Reinstall vent-grate: Tighten 7 / 16 " nuts on each side of vent grate using a 7 / 16 " nutdriver (Fig.
– 34 – WEEKLY CLEANING — HR7E OVENS WITH SOLID BACK, ACCESS FROM FRONT Clean ceiling of oven interior to remove potential grease build-up. Excessive grease build-up on convection fan blade(s) and / or vent-grate will decrease oven's cooking performance over time.
– 35 – 3 . Using a 7 / 16 " nutdriver, r e m ove the center nut that secures the element cover (Fig. 61). Allow the element cover to swing down toward you (Fig. 62). 4. Raise element cover up and swing toward front of oven to clear rotor support and rotor arm (Fig.
– 36 – Fig. 67 5. With element cover in forwardmost position, lift up right side to clear right hinge pin; then lower right side and lift up left corner until left hinge clears left hinge pin (Fig. 64). Fig. 65 CENTER NUT FAN CENTER NUT FAN Fig. 64 6 .
– 37 – 9. After cleaning, reinstall 2 fan blades: Mate D-shaped hole on fan onto D-shaped shaft; then tighten nut (counterclockwise) (Fig. 68). Fig. 68 CENTER NUT FAN CENTER NUT FAN D HOLE 10. Reinstall element cover: Raise left hinge (end of U-chanel) up around left hinge pin (Fig.
– 38 – Fig. 73 HIGH SIDE TOWARD REAR SHORT SIDE TOWARD CENTER Fig. 71 Fig. 72 12. Swing element cover back and raise up to clear rotor support and rotor arm (Fig. 71). Continue swinging element cover back until mounting studs protrude through three holes in element cover.
– 39 – 15. Reinstall vent-grate: Tighten 7 / 16 " nuts on each side of vent grate using a 7 / 16 " nutdriver (Fig. 74). Fig. 74 THREAD NUTS ON BOTH SIDES.
– 40 – FORM 35511 (Feb. 2006) PRINTED IN U.S.A. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE 1. Control does not light up. 1. ON-OFF switch is not pressed ON. 2. Electric supply is interrupted; check circuit breaker. 2. Cooking too slow. 1. Fan blade(s) and ventilation area require routine cleaning.
Ein wichtiger Punkt beim Kauf des Geräts Hobart HR7E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hobart HR7E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hobart HR7E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hobart HR7E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hobart HR7E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hobart HR7E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hobart HR7E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hobart HR7E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hobart HR7E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
