Benutzeranleitung / Produktwartung HFB12 ML-114906 des Produzenten Hobart
Zur Seite of 23
701 RIDGE AVENUE TROY, OHIO 45374-0001 I N S T R U C T I O N S FORM 33794 (4-97) MODEL HFB12 ELECTRIC FLASHBAKE ® OVEN HFB12 ML-114906 (Without Power Cord) HFB12 ML-114909 (With Power Cord).
– 2 – © HOBART CORPORATION, 1997 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . .
– 3 – Installation, Operation and Care of HOBART MODEL HFB12 FLASH BAKE ® OVEN KEEP THIS MANUAL FOR FUTURE REFERENCE GENERAL Your Hobart Flash Bake oven is a versatile oven that employs a revolutionary high quality, high-speed cooking technology.
– 4 – There must be a 3" (76 mm) clearance on each side of the oven. The area behind the oven around the blower must be kept clear of obstructions and allow for free air circulation. If your oven is equipped with the power cord and plug, ensure that the cord can be plugged into the appropriate outlet.
– 5 – The other end of the duct can be vented into an existing hood, or to the outside in a manner consistent with local building codes. The exhaust duct must not be less than 4" (101.5 mm) in diameter, and a recommended maximum length of 4 to 6 feet (1219-1829 mm), depending on operating conditions.
– 6 – Fig. 2 ELECTRICAL DATA *50A if cord connected. START-UP TESTING After the oven is connected to the supply circuit, perform the following tests to ensure that the oven is operating properly. Lamp Test Turn the oven on by pressing the ON/OFF button.
– 7 – Press the 1 button to begin the lamp test. The door will lock and the lamps will each turn on briefly. After each lamp is turned on successfully, the display will report Lamp OK. If all lamps pass, the oven will automatically return to the normal operating mode.
– 8 – OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR SERVICING THE OVEN. PRECAUTIONS • Never attempt to open the oven door while a cook cycle is in progress. Never attempt to operate the oven with the door open.
– 9 – DISPLAY — The display screen, located at the top of the control panel provides a constant indication of the oven status. It is also used for programming the oven and for the display of information and diagnostic messages. START — Press this button to begin cooking with the programmed recipe that is currently displayed.
– 10 – Next, a screen for selecting a cook method is displayed. Select A Cook Method 1 = Standard 2 = Two-Step There are two methods of cooking with the Flash Bake oven. They are called STANDARD and TWO-STEP . See pages 11 and 13 for a description of each method.
– 11 – Fig. 4 Changing the top outer and bottom outer power levels will have a greater effect on cooking times and browning than changing the center power levels. This is because outer intensities contain 70% of the cooking energy, while the center intensities only contain 30% of the cooking energy.
– 12 – Cook Time The cook time is the total amount of time the product will be cooked for this recipe. The time is entered in minutes and seconds using the 1 through 0 buttons. As the 1 through 0 buttons are pressed, the number enters in the right column and is shifted to the left as subsequent numbers are entered.
– 13 – Standard Recipe Display This screen is displayed after the recipe is saved, indicating the new settings as programmed. Recipe 1 0:00 Top 8 Bottom 3 Time 1:30 The clock on the top line at the right of the screen is the countdown timer for the cook cycle.
– 14 – Step 2 Time Recipe 1 Step 2 Enter Time For Step 2 = 2:05 Then Press NEXT Use the 0 through 9 buttons to enter the standard cook portion of the time. Press 2, 0, 5 to enter the 2 minutes and 5 seconds shown. Press the NEXT button to proceed to the next screen.
– 15 – Do You Want To Save This New Recipe 2 1 = Yes 2 = No Press the 1 button to store the new settings in memory. Two-Step Recipe Display This screen displays the saved programmed information for a Two-Step recipe.
– 16 – Once a recipe is programmed, it can be used again and again by selecting it and pressing the START button. Starting a Recipe All cooking must be done with the grill in place. To begin a cook cycle, place the pan with the product on the grill and close the door (pizza may be placed directly on the grill).
– 17 – COOK CYCLE COUNTER The Flash Bake oven is equipped with a cook cycle counter. This counter keeps a continuous log of the number of cook cycles performed by the oven. A cycle is counted when a recipe that lasts for more than approximately 30 seconds is completed.
– 18 – To make the adjustment, press the 1 button. Pressing the 2 button will take you to the normal programming screen for the cook time. Pressing the 1 button will take you to the following screen: Recipe 1 1 = lighter . . . 5 = darker Enter (1-5) = 3 Then Press NEXT The factory setting for this adjustment is 3.
– 19 – Approved Cleaning Materials and Procedures Cleaners • Mild dish soap - Use any mild food service type dish soap for the interior cleaning. Be sure that the soap is non-caustic. • Citrus 2000 Multi-Purpose Ready To Use • Pro Formula 409 - Use for interior walls.
– 20 – Fig. 5 OVEN DOOR LAMP SHIELD RAIL UPPER LAMP SHIELD LIFT LAMP SHIELD OVER RET AINING FEA TURE PULL LAMP SHIELD TOW ARD YOU LOWER LAMP SHIELD (NON REMOV ABLE) PL-52646 10. Clean the inside of the oven door window with a cloth dampened with window cleaner.
– 21 – MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE OVEN. WARNING: DISCONNECT THE ELECTRICAL SUPPLY BEFORE PERFORMING ANY MAINTENANCE ON THE OVEN. Do not remove the oven covers or attempt to open the control cabinet.
– 22 – PROBLEM No power to the oven. No power to the oven controls or display. Blower not operating. Oven not cooking. Display screen does not light up. Grill does not rotate. Door does not lock. No "High Power". TROUBLESHOOTING POSSIBLE CAUSES 1.
– 23 – FORM 33794 (4-97) PRINTED IN U.S.A. Under certain conditions, the oven will emit a short trill tone alarm when the operator presses a button.
Ein wichtiger Punkt beim Kauf des Geräts Hobart HFB12 ML-114906 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hobart HFB12 ML-114906 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hobart HFB12 ML-114906 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hobart HFB12 ML-114906 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hobart HFB12 ML-114906 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hobart HFB12 ML-114906 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hobart HFB12 ML-114906 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hobart HFB12 ML-114906. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hobart HFB12 ML-114906 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
