Benutzeranleitung / Produktwartung 55HDS52 des Produzenten Hitachi
Zur Seite of 88
PLASMA TELEVISION Operating Guide for 42HDS52, 42HDS52A and 55HDS52 IMPORT ANT SAFETY INSTRUCTIONS ....................................................................................... 2-3 FIRST TIME USE .............................................
2 Important Safety Instructions SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI PLASMA TELEVISION Our reputation has been built on the quality , performance, and ease of service of HIT ACHI plasma televisions. Safety is also foremost in our minds in the design of these units.
3 Important Safety Instructions Power source This plasma television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cor d into a 120 volt 60 Hz outlet.
4 Accessories First time use Check to make sure you have the following accessories befor e disposing of the packing material. CAUTION: 1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not provide adequate ventilation for the electronics or proper support for the front glass panel.
Securing to a table-top 1. Using wood screws (two) fasten the set to the clamping screw holes on the r ear of the Plasma Display stand as shown below . 2. Using commercially available wood scr ews, secure the set firmly in position. Securing to a W all 1.
6 How to set up your new HIT ACHI Plasma T elevision First time use VIEWING The best picture is seen by sitting dir ectly in front of the TV and about 10 to 18 feet from the scr een. During daylight hours, reflections fr om outside light may appear on the screen.
300-Ohm T win Lead Cable This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm). Phono Connector Used on all standard video and audio cables which connect to inputs and outputs located on the television’ s rear jack panel and fr ont control panel.
8 Quick Refer ence Remote Control Buttons and Functions First time use POWER BUTTON (TV , DVD, CBL, STB, PVR/VCR, AMP/CD) T urns the selected device on and off. SOURCE ACCESS BUTTONS (TV , DVD, CBL, STB, PVR/VCR, AMP/CD) Changes the mode of the Universal Remot e Control to control the device selected.
9 Fr ont/Rear/Side Panel Controls First time use R AUDIO L/MONO VIDEO S-VIDEO INPUT INPUT PHOTO PHOTO INPUT 5 INPUT 5 POWER CH CH CURSOR CURSOR VOL VOL INPUT/EXIT MENU/SELECT + + - - Firmly bind the cables.
10 POWER light indicator T o turn the monitor ON, press the main power switch located on the lower right side of the monitor . A red stand-by indicator lamp located on the lower right corner of the front bezel will illuminate. The Plasma TV is now ready for r emote ON/OFF operation.
Antenna Input The remote contr ol allows you to switch between two separate 75-Ohm RF antenna inputs, CABLE and AIR. Audio/Video INPUTS 1, 2, 3 and 4 By using the INPUTS button, the CURSOR P AD ( and ), and the SELECT button or CURSOR P AD of the remote contr ol, you can select each video source.
12 Subwoofer Out Connect this SUB WOOFER OUT output to the external audio component input using the sub woofer cable provided. Upgrade Card This card slot is for futur e software upgrades. HIT ACHI will notify you if a software upgrade is requir ed for your TV .
The front panel jacks ar e provided as a convenience to allow you to easily connect a camcor der or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to left side panel jacks. If you do not, the played back picture may be abnormal.
14 Rear Panel Connections First time use The Remote Control On-Screen Display VCR #1 Cable TV coaxial cable 2-Way signal splitter Outside A ntenna ANT IN OUTPUT S-VIDEO VL R DIGIT AL OUTPUT CAP ABILITY DIGITAL OUTPUT Laserdisc player , VCR, camcorder , etc.
• S-VIDEO, YPbPR, or HDMI connections are pr ovided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standar d video connection if your device has this feature. • If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the Rear Panel.
16 Connecting Exter nal V ideo Sources First time use CONNECTING A VIDEO AND STEREO AUDIO SOURCE TO INPUT1 – INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel to the right.
17 Connecting Exter nal V ideo Sources First time use CONNECTING A COMPONENT SOURCE WITH HDMI OR DVI CAP ABILITY TO INPUT 1 OR 2 1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the Rear panel below .
18 Connecting Exter nal V ideo Sources First time use CONNECTING A COMPONENT AND STEREO AUIDO SOURCE TO INPUT 3 OR 4: Y -P B P R . 1. Connect the cable fr om the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the Rear panel below .
CONNECTING A VIDEO AND MANAURAL AUDIO SOURCE TO INPUT 1, INPUT 2 OR INPUT 5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel on the right. 2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
20 Rear Panel Jacks Y our Hitachi Plasma T elevision is equipped with an A V Network feature. This feature helps to contr ol your external Audio/Video equipment (VCR, Set T op Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using your HIT ACHI Plasma TV Remote Control.
In addition to controlling all the functions on your HIT ACHI Plasma TV , the new remote control is designed to operate differ ent types of VCRs, CA TV (Cable TV) converters, set-top-box, satellite receiver , DVD players, and other audio/video equipment with one touch.
22 POWER button Press this button to turn the TV set on or off when the remote is in TV mode. (See page 21 for instructions on how to set the remote contr ol to TV mode.) MODE Indicator T ur ns on or blinks to show remote contr ol mode. 햴 SOURCE ACCESS ( or ) buttons Press these buttons to select r emote control mode.
23 How to Use the Remote to Contr ol Y our TV The Remote Control ASPECT button Press this button to quickly change the pictur e format ASPECT ratio. Depending on the input signal format received, the pictur e format ratio allows you to adjust the images through the following options.
24 DAY/NIGHT button Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness and contrast to compete with room light. Select Night for night time viewing with less brightness and contrast for a more detailed pictur e (see page 41 for settings changes).
1. Press the INPUTS button to cycle thr ough the INPUTS selections until the PHOTO INPUT is selected. Press the SELECT button or CURSOR P AD . 2. Press the CURSOR P AD or to access the next or previous photo. 3. Press the SELECT button to view THUMBNAIL.
26 ROTATE Select this menu item to rotate selected photos either clockwise (CURSOR P AD ) and counterclockwise (CURSOR P AD ). SLIDESHOW Select this menu item to start a slideshow of the digital photos. While the Interval sub menu is highlighted, press the SELECT button to cycle through the interval time fr om 5, 10 and 30 seconds.
LAST CHANNEL (LAST CH) button Press this button to toggle between the curr ent and last channel viewed. VOLUME (VOL) WHEEL, MUTE button Use the VOL WHEEL ( or ) until you obtain the desired sound level. T o reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc.
28 Y our HIT ACHI Plasma TV incorporates T wo T uner technology designed for improved viewing enjoyment. This T wo T uner feature allows you to view antenna inputs on both the main picture and sub pictur e simultaneously , with separate tuning control for each.
PIP MODE PICTURE-IN-PICTURE Select AIR from the INPUTS menu. Select a channel that has a 1080i signal. T o prevent a pattern burn, occasionally move the sub-picture using the CURSOR P AD. SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub- picture evenly on the scr een.
30 PAUSE button If you wish to freeze the sub-pictur e, press the P AUSE button. This is convenient when trying to write down the address for a mail or der company , recor ding statistics for a sporting event, etc. T o return the picture to motion, pr ess the EXIT button.
Operating the precoded function for your cable box. This remote is designed to operate dif ferent types of cable boxes. Y ou must first program the r emote to match the remote system of your cable box (r efer to pages 37-38 for pre-codes). 1. T ur n ON your cable box.
32 Operating the precoded function for your set-top- box/satellite receiver . This remote is designed to operate dif ferent types of set-top-box/satellite systems. Y ou must first program the remote to match the r emote system of your set- top-box/satellite systems (refer to pages 37-38 for pr e- codes).
Operating the precoded function for your DVD player. This remote is designed to operate dif ferent types of DVD players. Y ou must first program the r emote to match the remote system of your DVD player (r efer to pages 37-38 for pre-codes). 1. T ur n ON your DVD player .
34 The Remote for VCR/PVR Functions The Remote Control Operating the precoded function for your VCR/PVR (Personal Video Recorder). This remote is designed to operate dif ferent types of VCRs/PVRs. Y ou must first program the r emote to match the remote system of your VCR/PVR (r efer to pages 37-38 for pre-codes).
Operating the precoded function for your Audio component. This remote is designed to operate dif ferent types of Audio component. Y ou must first program the r emote to match the remote system of your Audio component (refer to pages 37-38 for pr e-codes).
36 INPUT ACCESS This optional feature allows the user of the r emote control to setup it’ s ENTER (ENT) button to access the specified input of the TV . Setup for this featur e is applicable to the remote contr ol’ s normal mode only and only applies to the DVD, CBL, STB, PVR and AMP modes.
37 Remote Contr ol Codes The Remote Control VCR BRAND ..................CODE ABS ..................................1972 Admiral ....................0048, 0209 Adventura .........................0000 Aiko ....................................0278 Aiwa .
38 Remote Contr ol Codes The Remote Control Jasco ............0015, 0153, 0315 Jerrold ......... 0003, 001 1, 0012, 0014, 0015, 0024, 0276, 0476, ..........................................0810 Memorex ...........................0000 Motorola ...... 0276, 0476, 0810, .
1. Press MENU on the r emote control to display the differ ent features on your HIT ACHI Plasma TV . 2. Use the CURSOR P AD (buttons , , and ) or CHANNEL WHEEL to navigate to a dif ferent menu item. 3. Press EXIT on the r emote control to quickly exit from a menu.
40 On-Scr een Display On-Screen Display Picture Mode Select between the two picture modes; Day and Night. Contrast Adjust contrast. Brightness Adjust brightness.
41 V ideo On-Screen Display Select VIDEO to adjust picture settings and impr ove picture quality . Y ou can independently customize each of the Video Inputs to your pr eference to incr ease viewing performance and pleasure depending upon the video program being viewed.
42 V ideo On-Screen Display Color T emperature Set this to High for cooler color with more blue, set to Medium for mor e natural color , set to Standard for accurate color or set to Black/White for more r eddish color . Black Enhancement Use this function to enhance the shadow detail in dark scenes using the settings off, low , middle and high.
Set Black Side Panel The BLACK SIDE P ANEL function tur ns the gray side bars on/off when watching 4:3 signals in Standar d mode or use of the PIP modes. 1. Press the CURSOR P AD or to set to ON or OFF . 2. Press EXIT to quit menu or select SET BLACK SIDE P ANEL to return to the previous menu.
44 Audio Select AUDIO to adjust the TV to your prefer ence and to improve the sound quality . 1. Press CURSOR P AD or to select menu item. 2. Press CURSOR P AD or to adjust the function. 3. Press EXIT to quit the MENU, or select AUDIO to return to the main menu.
Audio Source Multi-Channel T elevision Sound will allow you to select STEREO (a stereo br oadcast), MONO (monaural sound) used when receiving a weak ster eo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary language, weather report, etc. Internal Speakers This function is useful when setting up the external speakers.
46 Channel Manager Select CHANNEL MANAGER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. 1. Press CURSOR P AD , or CHANNEL WHEEL to highlight function 2. Press the SELECT button or CURSOR P AD to select.
Channel List This function allows you to review which channels ar e labeled (CH ID) , which have been added to CHANNEL MEMOR Y (SCAN) , which are pr otected by LOCK and which are your F A VORITE (F A V) CHANNELS . 1. Use the CURSOR P AD to navigate the Channel List.
48 Locks This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. The code to enter the Locks feature is a four digit access code number .
Movie Ratings Use Movie Ratings to prevent viewing of any movie that you feel may be inappropriate due to its content. 1. Use the CURSOR P AD , or CHANNEL WHEEL to select the MOVIE RA TING category that you want to block. 2. Press SELECT to block the MOVIE RA TING that you have selected.
50 Locks TV Ratings Use TV RA TINGS to prevent the viewing of any TV program that you feel may be inappr opriate due to its content. 1. Use the CURSOR P AD , or CHANNEL WHEEL to select the TV RA TING category that you want to block. 2. Press SELECT to block the TV RA TING that you have selected.
Canadian Ratings (Eng) Use CANADIAN RA TINGS (ENG) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. 1. Use the CURSOR P AD , or CHANNEL WHEEL to select the CANADIAN RA TINGS (ENG) category that you want to block.
52 Locks Canadian Ratings (Frn) Use CANADIAN RA TINGS (FRN) to block Canadian French pr ograms according to various pr ogram ratings that you feel might be inappropriate in its content. 1. Use the CURSOR P AD , or CHANNEL WHEEL to select the CANADIAN RA TINGS (FRN) category that you want to block.
Select TIMERS to set your Clock, Sleep Timer , Event Timer and Day/Night Timer Recordings. 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2. Press the SELECT button to select. Set The Clock The Clock must be adjusted before you can use the SET EVENT TIMER or DA Y/NIGHT TIMER feature.
54 Locks Set Sleep Timer Select this feature to set your SLEEP TIMER fr om 30 minutes to 3 hours (30 minute increments). 1. Press the CURSOR P AD repeatedly to set your Timer from 0:00 , 0:30 , 1:00 , 1:30 , 2:00 , 2:30 and 3:00 . Set Day/Night Timer Select this feature to activate and set your TV’ s DA Y/NIGHT PICTURE MODE automatically .
Set Event Timer This function will automatically operate the Plasma TV viewing reservation of a pr ogram. If the clock is not set, you can not use this function and the screen below will appear . The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 53).
56 Setup Select SETUP when setting your TV up for the first time. 1. Use the CURSOR P AD , , , to select the sub-menu of your choice. 2. Press the SELECT button to select. Menu Prefer ence Setup the Language and background of the Menu OSD.
Menu Background This function allows you to choose from two menu backgrounds. 1. Use the CURSOR P AD or to highlight SET THE MENU BACKGROUND (SHADED OR SOLID) of your choice.
58 Setup Set The Inputs Use this feature to give a name to any of the live video inputs. 1. Press the CURSOR P AD , to highlight the video inputs. 2. Press the CURSOR P AD , to select your choices. INPUT 4 Auto Link Use this function to automatically turn the TV on and tune to INPUT 4 when it detects a video signal to INPUT 4.
AV NET SETUP WIZARD ( Example: A/V RECEIVER Setup) 1. Press the SELECT button to start the SETUP WIZARD. 2. Use the CURSOR P AD or to highlight YES or NO. 3. Press the SELECT button to select “YES”. (Select YES to setup an A/V Receiver or NO to setup other devices).
60 Setup On-Screen Display 13. Use the CURSOR P AD or to select the A/V Receiver Source if you have connected the Monitor Out and Optical Out to the A/V receiver . Select “ Not Connected “ if not used. 14. Use the CURSOR P AD , , and to highlight NEXT , then press the SELECT button to move on to the next SETUP screen.
61 Setup On-Screen Display AV NET SETUP WIZARD ( Example: DVD Setup ) 1. Press the SELECT button to start the SETUP WIZARD. 2. Use the CURSOR P AD or to highlight NO. 3. Press the SELECT button to select. (Select NO to setup other devices). 4.
62 Setup On-Screen Display 15. Confirm all settings, then press the SELECT button to move on to the next SETUP screen. 16. Press the SELECT button to select YES to Setup another device. Press the CURSOR P AD or to highlight “ No thanks, Im done “, then press the SELECT button to exit the A/V NET SETUP .
63 Setup On-Screen Display 7. Use the CURSOR P AD , , and to select the Soft Key to learn (Ex. VOL ), then press the SELECT button.
64 Setup On-Screen Display 12. Select the T est button VOL to check the response of the device to this command. 13. Use the CURSOR P AD , , and to highlight NEXT , then press the SELECT button to move on to the next SETUP screen. 14.
65 Setup On-Screen Display IR Code Set Monitor Out Not Connected Other Brand Name Other TV Input Not Connected AV Net Setup Wizard : A/V Receiver Setup Move Optical Out All settings are complete! Not Connected Next Back SEL Select 22. Confirm all settings, then press the SELECT button to move on to the next SETUP screen.
66 Setup On-Screen Display 7. Use the CURSOR P AD or to choose the device you wish to learn. (Example: DVD 3) 8. Select NEXT to continue. 9. Select the DVD 3 softkey to learn.
67 Setup On-Screen Display 14. Select the T est button “Play button” to check the response of the device to this command. 15. Use the CURSOR P AD , , and to highlight NEXT , then press the SELECT button to move on to the next SETUP screen.
68 Setup Set Closed Caption Closed Captions are the dialogue, narration, and/or sound effects of a television pr ogram or home video which are displayed on the TV scr een. Y our local TV program guide denotes these pr ograms as or . 1. Use the CURSOR P AD , , and to highlight and select the function to change.
69 Setup On-Screen Display Set Monitor Out This feature will select the sour ce of the Monitor Output. Monitor : Select MONITOR to output the audio and video signals of the chosen input source (CABLE, AIR, INPUT 1-5) to a VCR or other A/V device.
70 Setup On-Screen Display TV TUNER OUT : A vailable Monitor Out Signals Upgrades This feature shows softwar e information and easy upgrade procedur e.
71 On-Screen Display Setup Quick Start Up This feature will select QUICK ST ART UP options. Set this feature to ON to have the TV tune channels (both Analog and Digital) quickly when first turning the TV on. Set this feature to OFF to save electricity .
72 Useful Information Equipment Car e and T roubleshooting TROUBLESHOOTING Y our HIT ACHI Plasma T elevision incorporates advanced power surge pr otection technology designed to protect against component or circuit damage due to external or internal voltage power surges.
73 Reception Pr oblems Useful Information IGNITION NOISE: Black spots or horizontal streaks may appear , picture may flutter or drift. Usually caused by interference fr om automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.
74 Useful Information T r oubleshooting No. Items Notes 1 Buzzing sound from Plasma display panel. A buzzing sound may be heard when the plasma television is turned on in a very quiet room. This is due to the plasma panel drive circuit when it is functioning.
75 Useful Info PLUG AND PLA Y This Class B digital apparatus meets all requir ements of the Canadian Interference-Causing Equipment Regulations. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
76 Useful Information Featur es and Specifications Features: • New Easy-to-Use On-Screen Menu Control (3 Language) • New A V Network System Control Control up to 4 components with one r emote 2 IR.
77 Set Dimensions Useful Information 42 Inch Models (Includes T able T op Stand) W eight (lbs./kg): 98/44.5 55 Inch Models (Plasma T elevision Only) W eight (lbs.
78 Hitachi HIT ACHI AMERICA, L TD. HOME ELECTRONICS DIVISION HIT ACHI has made every effort to assure you hours of trouble fr ee operation from your unit. However , should you requir e service, a network of HIT ACHI Authorized Service Facilities has been established in all 50 states and Puerto Rico.
79 End User License Agr eement for HIT ACHI DTV Softwar e END USER LICENSE AGREEMENT FOR HIT ACHI DTV SOFTW ARE IMPORT ANT – READ CAREFULL Y : This End User License Agreement for HIT ACHI DTV Softwa.
80 Appendixes Appendixes Appendix A: IMAGE INPUT INPUT TYPE FORMA T ASPECT VIDEO ID AUTO ASPECT Air or Cable -- NTSC 4:3 -- On/Off (Analog Channels) INPUT 1 & 2 HDMI 480i/480p 16:9 16:9 Off Letter Letter Off 4:3 4:3 Of f -- No Info. On/Off INPUT 1-5 S-Video 1 NTSC 16:9 16:9 Of f Video Letter Letter Off 4:3 4:3 Of f -- No Info.
81 Appendixes Appendixes 1. Press the MENU button on the Remote Contr ol to access the Main Menu screen. 2. Use the CURSOR P AD to highlight SETUP in the Main Menu and press the SELECT button. 3. Use the CURSOR P AD to highlight CableCARD Information and press the SELECT button.
82 A Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . .4 Antennas (Connecting), . . . . . . . . . . . . . . . . .6 Aspect Ratio, . . . . . . . . . . . . . . . . . . . . .23, 42 Audio T ruBass . . . . . . . . . . . . . . . . . . . . . . .
83 Notes.
84 Notes.
85 Notes.
86 Notes.
87 Notes.
QR64864.
Ein wichtiger Punkt beim Kauf des Geräts Hitachi 55HDS52 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hitachi 55HDS52 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hitachi 55HDS52 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hitachi 55HDS52 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hitachi 55HDS52 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hitachi 55HDS52 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hitachi 55HDS52 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hitachi 55HDS52. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hitachi 55HDS52 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
