Benutzeranleitung / Produktwartung 50C20 des Produzenten Hitachi
Zur Seite of 72
LCD REAR PROJECTION TELEVISION Operating Guide for 50C20 IMPORT ANT SAFETY INSTRUCTIONS ....................................................................................... 2-3 FIRST TIME USE ........................................................
2 SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI LCD REAR PROJECTION TELEVISION Our reputation has been built on the quality , performance, and ease of service of HIT ACHI televisions. Safety is also foremost in our minds in the design of these units.
Power source This television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cor d into a 120 volt 60 Hz outlet. The power cord is used as the disconnect device and shall remain r eadily operable.
4 Accessories Check to make sure you have the following accessories befor e disposing of the packing material. TV SA T CBL VCR DVD EXIT DA Y/NIGHT PIP ASPECT INPUTS MENU SELECT INFO MUTE GUIDE LAST CH FAV CH CLU-4361S VOL CH Remote Control Unit CLU-4361S (Part No.
5 How to set up your new HIT ACHI Pr ojection T elevision ANTENNA Unless your LCD Rear PTV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance.
6 Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased fr om most stores that sell audio/video products.
7 Quick Refer ence Remote Control Buttons and Functions First time use TV SA T CBL VCR DVD EXIT D A Y/NIGHT PIP ASPECT INPUTS MENU SELECT INFO MUTE GUIDE LAST CH FAV CH CLU-4361S VOL CH POWER BUTTON (TV , CBL, VCR, DVD, S AT ) Tu r n s the s elected device on and off.
8 Fr ont Panel Controls First time use INPUT/EXIT CHANNEL CURSOR VOLUME MENU/SELECT POWER S-VIDEO VIDEO AUDIO L/MONO R INPUT 5 MENU/SELECT button This button allows you to enter the MENU , making it possible to set TV features to your pr eference without using the remote.
POWER Light When the TV is turned ON, the Power Light will first blink to indicate that the television lamp is warming up. This light will be ON during normal operation. When the TV is turned OFF , the Power Light will blink to indicate that the television lamp will be cooling down and the light will eventually turn off.
10 First time use Side Panel Jacks and Connections The side panel jacks are pr ovided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to side panel jacks.
11 First time use Rear Panel Connections Antenna Input CABLE – CA TV (Cable TV) input. AIR – RF antenna input. NOTE: Y ou may ask your local cable company whether DTV services are available.
12 First time use Rear Panel Connections R L A U D I O V I D E O S I V I D E O (MONO) (MONO) (MONO) (MONO) P R P B Y/ VIDEO Y/ VIDEO P R P B P R P B P R P B MONITOR OUT AUDIO TO HI-FI INPUT 1 CABLE AI.
13 Rear Panel Connections First time use 1. Press the MENU button on the Remote Contr ol to access the Main Menu screen. 2. Use the CURSOR button to highlight SETUP in the Main Menu and press the SELECT button. 3. Use the CURSOR button to highlight CableCARD Information and press the SELECT button.
14 Rear Panel Connections First time use TIPS ON REAR P ANEL CONNECTIONS • S-VIDEO , Y- P B P R and HDMI connections are pr ovided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
15 Connecting Exter nal V ideo Sources First time use Match the numbers below to the diagram for speaker placement. The television’ s internal speakers will act as center speaker (select AUDIO - INTERNAL SPEAKERS - TV AS CENTER ). These FRONT left and right speakers are connected to the FRONT output of a separate audio amplifier .
16 First time use BEFORE OPERA TING EXTERNAL VIDEO SOURCE Connect an external source to the INPUT terminal, then press the INPUTS button to show the INPUTS menu. Use the CURSOR P AD to select the CABLE, AIR or INPUT of your choice. Then press the SELECT button to confirm your choice (see page 23).
17 First time use Connecting Exter nal V ideo Sources CONNECTING A COMPOSITE VIDEO AND STEREO AUDIO SOURCE TO INPUT1 – INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set on the right.
18 First time use CONNECTING A COMPONENT SOURCE WITH HDMI OR DVI CAP ABILITY TO INPUT 1 1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the TV set on the right.
19 First time use CONNECTING A COMPONENT SOURCE TO INPUT 3 OR 4: Y -P B P R . 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set on the right. 2. Connect the cable from the C B /P B OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P B ) jack.
20 The Remote Control In addition to controlling all the functions on your HIT ACHI LCD Rear Projection TV , the new remote control is designed to operate dif ferent types of VCRs, CA TV (Cable TV) converters, set-top-boxes, satellite receivers (SA T) and DVD players with one touch.
21 The Remote Control POWER button Press this button to turn the TV set on or off when the remote is in TV mode. MODE buttons These buttons allow the remote to contr ol your TV , VCR, DVD, Cable box/Satellite box depending on which button is pressed.
22 The Remote Control ASPECT button Press this button to quickly change the pictur e format ASPECT ratio. Depending on the input signal format received, the pictur e format ratio allows you to adjust the images through the following options.
23 The Remote Control INPUTS button When the remote contr ol is in TV mode, press this button to access the INPUTS menu. Use the CURSOR and SELECT buttons to scroll and select the inputs that are being used. Pr essing the INPUTS button repeatedly will also cycle thr ough the Inputs menu items.
24 The Remote Control VOLUME (VOL), MUTE button Press the VOLUME button ( or ) until you obtain the desired sound level. T o reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the MUTE button again to turn the sound off completely (MUTE).
25 The Remote Control Y our HIT ACHI LCD Rear Projection TV incorporates T wo T uner technology designed for improved viewing enjoyment. This T wo T uner feature allows you to view antenna inputs on both the main picture and sub-pictur e simultaneously , with separate tuning control for each.
26 The Remote Control Pictur e-in-Picture (PIP) PIP Mode Picture-in-Pictur e This feature is only available with a Digital 16:9, 720p and 1080i signal.
27 The Remote Control P AUSE button If you wish to freeze the sub-pictur e, press the P AUSE button. This is convenient when trying to write down the address for a mail or der company , recor ding statistics for a sporting event, etc. T o return the picture to motion, pr ess the EXIT button.
28 The Remote Control OPERA TING THE PRECODED FUNCTION FOR YOUR CABLE BOX. This remote is designed to operate dif ferent types of cable boxes. Y ou must first program the r emote to match the remote system of your cable box (r efer below for pre-codes).
29 The Remote Control OPERA TING THE PRECODED FUNCTION FOR YOUR SET -TOP-BOX/SA TELLITE RECEIVER. This remote is designed to operate dif ferent types of set-top-box/satellite systems. Y ou must first program the remote to match the r emote system of your set- top-box/satellite systems (refer below for pr e-codes).
30 The Remote Control OPERA TING THE PRECODED FUNCTION FOR YOUR DVD PLA YER. This remote is designed to operate dif ferent types of DVD players. Y ou must first program the r emote to match the remote system of your DVD player (r efer below for pre-codes).
31 The Remote Control OPERA TING THE PRECODED FUNCTION FOR YOUR VCR. This remote is designed to operate dif ferent types of VCRs. Y ou must first program the r emote to match the remote system of your VCR (r efer below for pre-codes). 1. T ur n ON your VCR.
32 1. Press MENU on the remote control to display the differ ent features on your HIT ACHI LCD Rear Projection TV . 2. Press the CURSOR buttons to navigate and highlight a differ ent feature of the On-Screen Display menu. Press the SELECT button to select.
33 On-Screen Display Picture Mode Select between the two picture modes; Day and Night. Contrast Adjust contrast. Brightness Adjust brightness. Color Adjust color .
34 On-Screen Display Select VIDEO to adjust picture settings and impr ove picture quality . Y ou can independently customize each of the Video Inputs to your pr eference to increase viewing performance and pleasure depending upon the video program being viewed.
35 On-Screen Display Color T emperature Set this to High for cooler color with more blue, set to Medium for mor e natural color , set to Standard for accurate color or set to Black/White for more r eddish color . Black Enhancement Use this function to enhance Picture brightness in light scenes using the settings of f, low , middle and high.
36 On-Screen Display V ertical Position This function allows you to select when aspect style is either 4:3 EXP ANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. V ertical position can be changed with these modes. For example, it will be useful for centering the picture ar ea at both the top and bottom of the picture with 480i/480P signal.
37 On-Screen Display Select AUDIO to adjust the TV to your prefer ence and to improve the sound quality . 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2. Press the CURSOR buttons or to adjust the function. 3. Press EXIT to quit the menu or select AUDIO to return to the main menu.
38 On-Screen Display Audio Source Multi-Channel T elevision Sound will allow you to select STEREO (a stereo br oadcast), MONO (monaural sound) used when receiving a weak ster eo broadcast or SECOND AUDIO PRO G (SA) which may be a secondary language, weather report, etc.
39 On-Screen Display Use the functions below if your TV is connected to an amplifier/receiver with OPTICAL DI G IT AL INPUT with Dolby Digital or PCM decoder capabilities. 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2.
40 On-Screen Display Select CHANNEL MANA G ER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2. Press the SELECT button or CURSOR button to select.
41 On-Screen Display Auto Channel Scan This feature will automatically stor e active TV channels in Auto Channel Scan memory . 1. Use the CURSOR buttons or to highlight CABLE or AIR . 2. Press the CURSOR buttons or to highlight the ST ART or RESET option.
42 On-Screen Display This function will block out the picture and sound of the selected channel or video input. The code to enter the Locks feature is a four digit access code number . The factory preset code is 0000 . Use the NUMBER buttons to enter the access code.
43 On-Screen Display Movie Ratings Use Movie Ratings to prevent viewing of any movie that you feel may be inappropriate due to its content. 1. Use the CURSOR buttons or to select the MOVIE RA TIN G category that you want to block. 2. Press SELECT to block the MOVIE RA TIN G that you have selected.
44 On-Screen Display Locks TV Ratings Use TV RA TIN G S to prevent the viewing of any TV program that you feel may be inappr opriate due to its content. 1. Use the CURSOR buttons or to select the TV RA TIN G category that you want to block. 2.
45 On-Screen Display Canadian Ratings (Eng) Use CANADIAN RA TIN G S (EN G ) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. 1. Use the CURSOR buttons or to select the CANADIAN RA TIN G S (EN G ) category that you want to block.
46 On-Screen Display Canadian Ratings (Frn) Use CANADIAN RA TIN G S (FRN) to block Canadian French pr ograms according to various program ratings that you feel might be inappropriate in its content. 1. Use the CURSOR buttons or to select the CANADIAN RA TIN G S (FRN) category that you want to block.
47 On-Screen Display Select TIMERS to set your Clock, Sleep Timer , Event Timer and Day/Night Timer Recordings. 1. Use the CURSOR buttons or to highlight the function to be adjusted.
48 On-Screen Display Set Sleep Timer Select this feature to set your SLEEP TIMER fr om 30 minutes to 3 hours (30 minute increments). 1. Press the CURSOR buttons or repeatedly to set your Timer from 0:00 , 0:30 , 1:00 , 1:30 , 2:00 , 2:30 and 3:00 .
49 On-Screen Display Timers Set Event Timer This function will automatically operate the Projection TV viewing reservation of a pr ogram. If the clock is not set, you can not use this function and the screen below will appear .
50 On-Screen Display Select SETUP when setting your TV up for the first time. 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2. Press the SELECT button or CURSOR button to select. Menu Prefer ence This feature will allow you to select any one of thr ee differ ent languages for all on-screen displays.
51 On-Screen Display Lamp Power Control Use this featureto have the TV turned OFF automatically when a video signal is not detected for 15 minutes. 1. Press the CURSOR buttons or to highlight Y es or No. Set The Inputs Use this feature to give a name to any of the five video inputs.
52 On-Screen Display Setup INPUT 4 Auto Link Use this function to automatically turn the TV on and tune to INPUT 4 when it detects a video signal to INPUT 4.
53 On-Screen Display Digital Captions Set captions for digital programs. This function will help choose and set available language, font, size and style of digital captions. 1. Use the CURSOR buttons , , or to highlight and select DI G IT AL CAPTIONS feature.
54 On-Screen Display MONITOR : Available Monitor Out Signals TV TUNER OUT : A vailable Monitor Out Signals Setup Input Mode Monitor Out S-Video Video L/R HiFi ANT Digital No Macrovision S-Video YES YE.
55 On-Screen Display Upgrades It shows software information and easy upgrade procedur e. This function allows the TV software to be upgraded by using a flash card (MMC CARD). If a future softwar e upgrade is required for your TV , HIT ACHI will notify and provide you with a flash card.
56 Lamp Replacement Lamp Life The lamp life may vary based on usage of the LCD Rear PTV . T ur ning on and off fr equently may shorten the life of the lamp. Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICA TOR light tur ns on, then it is time to replace the lamp with a new lamp.
57 Lamp Replacement Lamp Replacement Lamp Replacement 1. T ur n off the main power switch and unplug the power cor d. Wait at least 30 minutes to allow the lamp to cool down before r eplacing it. CAUTION: The lamp is very hot and may cause fire or severe burns.
58 Lamp Replacement 3. Remove the screw securing the lamp cover with a Phillips head scr ew driver as shown. Remove the lamp cover . CAUTION: The lamp is very hot and may cause fire or severe burns. Wait at least 30~45 minutes to allow the lamp to cool before proceeding with lamp removal.
59 Lamp Replacement 6. If the lamp cover is not installed, be sure to install the lamp cover by r e-engaging the two clips and tighten the screws befor e turning the power on, otherwise it may cause unusual colors. NOTE: If power is connected before the Lamp Cover is installed, the power will be off and the Lamp Indicator will flash (see page 9).
60 Useful Information TROUBLESHOOTING HIT ACHI LCD Rear Projection T elevision incorporates advanced power sur ge protection technology designed to protect against component or cir cuit damage due to external or inter nal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HA VE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1.
61 Useful Information Reception Pr oblems I G NITION NOISE: Black spots or horizontal streaks may appear , picture may flutter or drift. Usually caused by interference fr om automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.
62 Useful Information FEA TURES: • Superfine Picture Quality; 1280 Line Horizontal Resolution • Remote (Controls many PVR/VCR brands, cable boxes, satellite boxes, and other audio equipment).
63 Useful Information HIT ACHI HIT ACHI AMERICA, L TD. HOME ELECTRONICS DIVISION HIT ACHI has made every effort to assure you hours of trouble fr ee operation from your unit. However , should you requir e service, a network of HIT ACHI Authorized Service Facilities has been established in all 50 states and Puerto Rico.
64 License Agreement END USER LICENSE AGREEMENT FOR HIT ACHI DTV SOFTW ARE IMPORT ANT – READ CAREFULL Y : This End User License Agreement for HIT ACHI DTV Software (this “Agreement”) is a legal .
65 Appendix A: IMAGE INPUT INPUT TYPE FORMA T ASPECT VIDEO ID AUTO ASPECT Air or Cable -- NTSC 4:3 -- On/Of f (Analog Channels) Input 1 HDMI 480i/480p 16:9 16:9 Off Letter Letter Off 4:3 4:3 Off -- No Info. On/Off Inputs 1-5 S-Video 1 NTSC 16:9 16:9 Off Video Letter Letter Off 4:3 4:3 Off -- No Info.
66 Index A Accessories ................................................................4 Antennas (Connecting) ...............................................6 Aspect Ratio .............................................................22 Audio Languages .
67 Notes.
68 Notes.
69 Notes.
70 Notes.
71 Notes.
QR67171.
Ein wichtiger Punkt beim Kauf des Geräts Hitachi 50C20 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hitachi 50C20 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hitachi 50C20 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hitachi 50C20 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hitachi 50C20 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hitachi 50C20 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hitachi 50C20 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hitachi 50C20. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hitachi 50C20 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
