Benutzeranleitung / Produktwartung 50C10 des Produzenten Hitachi
Zur Seite of 72
LCD REAR PROJECTION TELEVISION Operating Guide for 50C10, 50C10E IMPORT ANT SAFETY INSTRUCTIONS ................................................................................ 2-3 FIRST TIME USE .......................................................
IMPORT ANT SAFETY INSTRUCTIONS 2 SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI LCD REAR PROJECTION TELEVISION Our reputation has been built on the quality , performance, and ease of service of HIT ACHI televisions. Safety is also foremost in our minds in the design of these units.
IMPORT ANT SAFETY INSTRUCTIONS 3 Read before operating equipment Follow all warnings and instructions marked on this television. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water .
ACCESSORIES 4 1. Remote Control Unit CLU-4329UG (Part No. HL01839). 2. T wo “AA” size, 1.5V batteries (For Remote Control Unit). REMOTE CONTROL BA TTER Y INST ALLA TION AND REPLACEMENT 1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the cover off.
HOW T O SET UP YOUR NEW HIT ACHI LCD REAR PTV 5 ANTENNA Unless your LCD Rear PTV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for best performance.
HOOK-UP CABLES AND CONNECTORS 6 ANTENNA CONNECTIONS TO REAR JACK P ANEL VHF (75-Ohm) antenna/CA TV (Cable TV) When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CA TV coaxial cable to the ANT A (75-Ohm) terminal. If you have a second antenna or cable TV system, connect the coaxial cable to the ANT B terminal.
FRONT P ANEL CONTROLS 7 INPUT 5 S-VIDEO EXI T INPUT SELECT MENU VOL- VOL+ CH- CH+ VIDEO AUDI O L/MONO R PUSH PUSH CURSOR MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote.
FRONT P ANEL CONTROLS 8 FIRST TIME USE IR RECEIVER The screen area also acts as the IR receiver (remote sensor) of the TV . When using the remote control, point it towards the screen for best response. POWER button Press this button to turn the TV on or of f.
9 FRONT P ANEL JACKS AND CONNECTORS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks.
10 REAR P ANEL JACKS Antenna Input/Output ANT A - A 75-Ohm RF antenna or CA TV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture. ANT B - A 75-Ohm RF antenna or CA TV (Cable TV) input. ANT B can only be displayed as a main picture.
11 REAR P ANEL JACKS Component: Y -P B P R Inputs Inputs 1 and 2 provide Y -P B P R jacks for connecting equipment with this capability , such as a DVD player or Set T op Box. Y ou may use composite video signal for INPUT :2. NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time.
12 REAR P ANEL CONNECTIONS NOTES: 1. Connect only 1 component to each input jack. 2. Follow connections that pertain to your personal entertainment system. 3. Composite video signal can be input to Input2~Input5. 4. Cables are not included with the purchase of this TV , except when noted as “provided”.
13 TIPS ON REAR P ANEL CONNECTIONS • S-VIDEO and DVI-HDTV connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
14 CONNECTING EXTERNAL AUDIO DEVICES T o control the audio level of an external audio amplifier with the TV remote control, connect the system as shown below . NOTES: 1. T o prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust the sound using the remote control of the TV set.
15 CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A MONAURAL AUDIO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.
16 CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A STEREO SOURCE T O INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
17 CONNECTING EXTERNAL VIDEO DEVICES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
18 CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAP ABILITY T O INPUT 1 1. Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on the TV set below .
19 CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE T O INPUT 1 OR 2: Y -P B P R . 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below .
20 THE REMOTE CONTROL In addition to controlling all the functions on your HIT ACHI LCD Rear PTV , the new remote control is designed to operate differ - ent types of VCRs, CBL (Cable TV) converters, satellite receiver , DVD players, and other audio/video equipment with one touch.
21 HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV POWER button Press this button to turn the TV set on or of f when the remote is in TV mode. PICTURE-IN-PICTURE buttons See separate section on pages 25, 26 and 27 for description. 햴 DA Y/NIGHT button Press this button to toggle between Day and Night picture mode settings.
22 HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc.
23 ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 Standard Use this aspect mode to display conventional (4:3) images.
24 HOW T O USE THE REMOTE TO CONTROL YOUR LCD REAR PTV SLEEP button Press this button to display the sleep timer in the lower center of the screen. Every subsequent press of this button will add 15 minutes to this timer up to a maximum of three hours.
25 PICTURE-IN-PICTURE (PIP) Y our HIT ACHI LCD Rear PTV incorporates dual tuner technology designed for improved viewing enjoyment. This dual tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously , with separate tuning control for each.
26 PICTURE-IN-PICTURE (PIP) SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. SURF button PICTURE-IN-PICTURE This feature will automatica.
27 PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company , recording statistics for a sporting event, etc.
28 USING THE REMOTE T O CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. Y ou must first program the remote to match the remote system of your VCR (refer to page 31 for pre-codes).
29 USING THE REMOTE T O CONTROL CABLE/SA TELLITE BOX FUNCTIONS Operating the precoded function for your cable/satellite box. This remote is designed to operate different types of cable/satellite boxes. Y ou must first program the remote to match the remote sys- tem of your cable/satellite box (refer to page 31).
30 USING THE REMOTE T O CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player . This remote is designed to operate different types of DVD players. Y ou must first program the remote to match the remote system of your DVD player (refer to page 31 for pre-codes).
31 VCR, CABLE, SA TELLITE, DVD and AUDIO CODES FOR REMOTE CONTROL CABLE BRAND CODE General Instrument . . . . . . . . . . . . . . . . . . . . . . . . . .17 Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23,24,25 Jerrold . . . . . . .
32 ON-SCREEN DISPLA Y (OSD) PUSH Locks Chan. Manager Aspect Audio Video Move SEL Sel Setup This part of the screen shows which selections are available. This part of the screen shows which Remote Control buttons to use. 1. Press MENU on the remote control to display the different features on your HIT ACHI LCD Rear PTV .
33 ON-SCREEN DISPLA Y (OSD) Picture Mode Select between the two picture modes; Day and Night. Contrast Adjust contrast. Brightness Adjust brightness. Color Adjust color .
VIDEO 34 Select VIDEO to adjust picture settings and improve picture quality . Y ou can customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected mode will reset to initial conditions.
VIDEO 35 Use this function to change the contrast between black and white levels in the picture. Use the CURSOR button or to highlight the function to be adjusted. Press the SELECT button or CURSOR button to select the function settings. Press the CURSOR buttons or to adjust the function.
VIDEO 36 This function allows you to Reset the Video Menu Settings of the present input and return it to the Day Mode condition depending on the selected Video mode. Use CURSOR button or to highlight functions. Press the SELECT button to select RESET VIDEO SETTINGS.
VIDEO 37 Use this function to adjust the percentage of Red, Green and Color according to the user ’ s preference. Use T int to adjust flesh tones so they appear natural.
AUDIO 38 Select AUDIO to adjust the TV to your preference and to improve the sound quality . Audio Sound Enhancement Balance Bass Treble Audio Move SEL Return Internal Speakers Audio Source Loudness Auto Noise Cancel 50% Off On Locks Chan.
AUDIO 39 Sound Enhancement The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc.
40 ASPECT MODE Aspect Mode Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. Press CURSOR buttons or to select menu item. Press the SELECT button to select. A “ ✓ ” in the box indicates that the feature is ON.
CHANNEL MANAGER 41 Select Antenna if you are using an indoor or outdoor antenna. Select Cable if you have cable TV . Use the CURSOR buttons or to highlight the correct Channel Source. Press the SELECT button to select highlighted source. Press EXIT to quit the MENU or select CHAN.
CHANNEL MANAGER 42 This feature will automatically store active TV channels in AUTO CHANNEL SCAN. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ). If the EXIT button is pressed while AUT O CHANNEL SCAN function is engaged, programming will stop.
43 CHANNEL MANAGER Press the CURSOR button or to review more channels. Press EXIT to quit the menu or select CHANNEL LIST to return to previous menu. Move SEL Return Ch# Scan CH ID Lock 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Chan.
44 ON-SCREEN DISPLA Y CHANNEL MANAGER This section contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when Antenna signal source is selected and up to 60 channels a name when Cable TV signal source is selected.
LOCKS 45 ON-SCREEN DISPLA Y This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. The code to enter the Locks feature is a four digit secret code number .
LOCKS 46 ON-SCREEN DISPLA Y Use MOVIE RA TINGS to block from showing any movie you feel might have inappropriate content. Use CURSOR or to select the MOVIE RA TING category that you want to block. Press SELECT to block the MOVIE RA TING that you have selected.
LOCKS 47 ON-SCREEN DISPLA Y TV Ratings Move SEL Return Status TV-Y: TV-Y7: TV-G: TV-PG: TV-14: TV-MA: Sub Category DL S VF V Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Se.
LOCKS 48 Canadian Ratings (Eng) Move SEL Return Status C: C8+: G: PG: 14+: 18+: Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Select Canadian Ratings (Frn) Canadian Ratings .
LOCKS 49 Canadian Ratings (Frn) Move SEL Return Status G: 8 ans+: 13 ans+: 16 ans+: 18 ans+: Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Move SEL Select Canadian Ratings (Frn) Cana.
SETUP 50 Select SETUP when setting your TV up for the first time. Use the CURSOR or on the remote to highlight the function desired. This feature will allow you to select any one of three different languages for all on-screen displays. Use CURSOR or to highlight the language of your choice.
SETUP 51 This function allows you to choose from two menu backgrounds. Use CURSOR or to highlight Set The Menu Background (shaded or solid), and press the SELECT button to select setting. Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.
SETUP 52 The time must be adjusted before you can use the “Set Event T imer” or “TV Time Out” features. Set The Clock Move SEL Return Time : 03:57 PM Apr 29, 2003 Move SEL Return Time : 03:57 .
SETUP 53 Use this feature to give a name to any of the five video inputs. Press CURSOR , , and to highlight the name of the video inputs. Press the SELECT button to select desired input name. Select Reset to set video names to original factory preset condition.
SETUP 54 Set The Color System Set Black Side Panel This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition T elevision - Use for High Vision Signal Y -P B P R from HDTV Set-T op Box. SDTV/DVD - Standard Definition T elevision or DVD (Digital V ersatile Disc Player) Y -C B C R .
SETUP 55 This function will automatically turn the LCD Rear Projection TV on and of f, one time only , every day , or once a week. This Event Timer is only for Ant A/Ant B. Use CURSOR to select Event 1, 2, 3 or 4. Use CURSOR to change position of On time, Off time, Antenna, Channel, and On/Off Frequency .
56 SETUP CLOSED CAPTIONS are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Y our local TV program guide denotes these programs as or .
57 LAMP REPLACEMENT Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICA TOR light turns on, then it is time to replace the lamp with a new lamp. Lamp Life The lamp life may vary based on usage of the LCD Rear PTV .
58 LAMP REPLACEMENT 120V PUSH POWER FRONT COVER 1. T urn off the main power switch and unplug the power cord. W ait at least 30 minutes to allow the lamp to cool down before replacing it. NOTE: THE LAMP IS VER Y HOT AND MA Y CAUSE FIRE OR SEVERE BURNS.
59 LAMP REPLACEMENT SCREW LAMP COVER PHILLIP HEAD SCREW DRIVER INPUT 5 S-VIDEO EXI T INPUT SELECT MENU VOL- VOL+ CH- CH+ VIDEO AUDIO L/MONO R 3. Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover .
60 LAMP REPLACEMENT 6. Without installing the lamp cover , the power will be off and the Lamp Indicator will flash (see page 8). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors.
61 CARE OF YOUR HIT ACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty .
62 RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear , picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths.
USEFUL INFO 63 HIT ACHI Liquid Crystal Display incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR T O HA VE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1.
USEFUL INFO 64 Features: • Superfine Picture Quality 1280 Line Horizontal Resolution • Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment). • New Easy-to-Use (3-Language) On-Screen Menu • Full Set of Input Jacks, including S-VIDEO • COMPONENT VIDEO: Y -P B /P R Inputs: • Power Input .
USEFUL INFO 65 Hitachi America, L TD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However , should you require service , a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO 66 In Canada: 1-800-HIT ACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Hitachi Canada, L TD. Digital Media Division Should you have any questions regarding warranty , service, operation, or technical assistance, please contact: Look for your French Manual on the outside of the box.
67 INDEX INDEX Clock T ime, 52 A Date, 52 Closed Captions Accessories, 4 Analog Captions, 56 Antennas (Connecting), 5, 6 Color System, 54 Aspect Ratio, 23 Color T emperature, 35 Audio (Sound Enhanceme.
68 INDEX L Picture-in-Picture (PIP), 25 - 27 Lamp Picture-outside-Picture (POP), 25 Lamp Indicator , 8 Lamp Replacement, 57-60 Language Menu Language, 50 R Locks Remote Control Change Access Code, 45 .
69 NOTES.
70 NOTES.
71 NOTES.
QR63612.
Ein wichtiger Punkt beim Kauf des Geräts Hitachi 50C10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hitachi 50C10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hitachi 50C10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hitachi 50C10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hitachi 50C10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hitachi 50C10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hitachi 50C10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hitachi 50C10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hitachi 50C10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
