Benutzeranleitung / Produktwartung 32UDX10S, 36UDX10S des Produzenten Hitachi
Zur Seite of 68
SOLID ST A TE COLOR TV 32UDX10S 36UDX10S OPERA TING GUIDE IMPORT ANT SAFEGUARDS 2-3 FIRST TIME USE 4-20 THE GENIUS REMOTE CONTROL UL TRA TEC BIT -MAP ON-SCREEN DISPLA Y USEFUL INFORMA TION INDEX 60-67.
2 IMPORT ANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI TELEVISION Our reputation has been built on the quality , performance, and ease of service of HIT ACHI televisions. Safety is also foremost in our minds in the design of these units.
IMPORT ANT SAFETY INSTRUCTIONS 3 ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUNDING CONDUCTORS POWER SERVICE GROUNDING ELECTRODE SYSTE.
4 ACCESSORIES Check that you have the following accessories before disposing of the packing material. 1. Remote Control Unit. 2. T wo AA size, 1.5V batteries (For Remote Control Unit).
5 BOTTOM VIEW Lift up on tab to remove back cover. REMOTE CONTROL BA TTER Y INST ALLA TION AND REPLACEMENT 1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers, and pulling the cover off. 2. Insert two new AA size batteries in the remote.
6 HOW T O SET UP YOUR NEW HIT ACHI COLOR TV ANTENNA Unless your color TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance.
7 HOOK-UP CABLES AND CONNECT ORS Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products.
FRONT P ANEL CONTROLS 8 NOTES: 1. Y our HIT ACHI TV will appear to be turned OFF if there is no video input when VIDEO: 1, 2 or 3 is selected. Check the Power Light to make sure the TV is turned of f when not in use.
FRONT P ANEL CONTROLS 9 PUSH POWER CH - CH + VOL - VOL + MENU INPUT CURSOR POWER CH - CH + VOL - VOL + INPUT EXIT MENU CURSOR INPUT/ EXIT Infrared Sensor Power Button LED MENU Channel Buttons Volume B.
10 FRONT P ANEL JACKS AND CONNECTIONS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks.
11 REAR P ANEL JACKS Antenna Input/Output The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture.
12 REAR P ANEL JACKS NOTES: 1. DO NOT connect standard VIDEO or S-VIDEO to Input 2 when using Y -P B P R input. 2. When using the Y -P B P R input jacks, connect your components audio output to the T V s Input 2 Left and Right Audio input jacks. 3. Y our component output may be labeled Y , B-Y , and R-Y .
13 REAR SPEAKER TERMINAL CONNECTIONS P B P R DVD Player Stereo System Amplifier Laserdisc player , VCR, camcorder , etc. VCR #2 Cable TV Box Optional, see tips on page 14 VCR #1 Outside antenna or cab.
14 TIPS ON REAR P ANEL CONNECTIONS TIPS ON REAR P ANEL CONNECTIONS S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
15 CONNECTING EXTERNAL AUDIO SOURCES P B /C B P R / C R RL INPUT Stereo System Amplifier To Audio Input Terminal of External Amplifier MONITOR OUT INPUT 2 INPUT 1 AUDIO (MONO) L R AUDIO L R S-VIDEO S-.
16 CONNECTING EXTERNAL VIDEO SOURCES The exact arrangement you use to connect the VCR, camcorder , laserdisc player , DVD player, or HDTV Set T op Box to your TV set is dependent on the model and features of each component. Check the owner ’s manual of each component for the location of video and audio inputs and outputs.
17 CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A STEREO VCR OR STEREO LASERDISC PLA YER 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
18 CONNECTING EXTERNAL VIDEO SOURCES CONNECTING AN S-VIDEO VCR OR LASERDISC PLA YER 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below . 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.
19 CONNECTING EXTERNAL VIDEO SOURCES CONNECTING A STEREO LASERDISC/DVD PLA YER OR HDTV SET TOP BOX T O INPUT 2 COMPONENT : Y -P B P R . 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below .
AUDIO SYSTEM SETUP 20 PUSH POWER CH - CH + VOL - VOL + MENU INPUT CURSOR Match the numbers below to the diagrams for speaker placement and refer to the table for the different surround sound requireme nts. (See page 58 for SRS and BBE functions.) The television s inte rnal speakers.
21 THE GENIUS REMOTE CONTROL (CLU-577TSI) In addition to controlling all the functions on your HIT ACHI color TV , the new remote control is designed to operate different types of VCRs, CA TV (Cable TV) converters, satellite receivers, DVD players, and other audio/video equipment with one touch.
22 HOW T O USE THE GENIUS REMOTE TO CONTROL YOUR TV POWER button Press this button to turn the TV set on or of f when the remote is in TV mode. TV button When the TV button is pressed, it will blink, to indicate the remote is in TV mode. VCR button When the VCR button is pressed, it will blink to indicate the remote is in VCR mode.
23 HOW T O USE THE GENIUS REMOTE TO CONTROL YOUR TV A V1, A V2, A V3 buttons When pressed, each of these buttons will blink to indicate the remote is in Audio/Video mode. (see page 32) SLEEP button Press this button to display the sleep timer in the lower left corner of the screen.
24 HOW T O USE THE GENIUS REMOTE TO CONTROL YOUR TV ASPECT button Press this button to quickly change the aspect ratio of the viewable video between 4:3 and 16:9.
25 PICTURE-IN-PICTURE (PIP) NOTES: 1. If you tune the main channel to a Y -P B P R input, the TV set will automatically turn the PIP sub-picture OFF . 2. When a Y -P B P R input is selected as PIP , it will appear as a blank sub-picture. 3. When main channel is tuned to a Y -P B P R input you will not be able to access the PIP functions.
26 PICTURE-IN-PICTURE (PIP) NOTES: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan channels in memory . (see pages 40 and 41) 2. If a channel is tuned during this SURF scanning, sub-pictures will be removed from the screen.
27 PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company , recording statistics for a sporting event, etc.
28 USING THE REMOTE T O CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. Y ou must first program the remote to match the remote system of your VCR. (refer to page 33 for pre-codes) 1.
29 USING THE REMOTE T O CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. This remote is designed to operate different types of cable boxes. Y ou must first program the remote to match the remote system of your cable box.
USING THE REMOTE T O CONTROL SA TELLITE RECEIVER FUNCTIONS 30 Operating the precoded function for your satellite receiver . This remote is designed to operate different types of satellite systems. Y ou must first program the remote to match the remote system of your satellite receiver .
31 USING THE REMOTE T O CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player . This remote is designed to operate different types of DVD players. Y ou must first program the remote to match the remote system of your DVD player . (refer to page 33 for pre-codes) 1.
32 Operating the precoded function for your Audio/Video component. This remote is designed to operate different types of Audio/Video component. Y ou must first program the remote to match the remote system of your Audio/Video component. (refer to page 33 for pre-codes) 1.
33 VCR, CABLE, SA TELLITE, DVD and AUDIO/VIDEO CODES (CLU-577TSI) VCR BRAND . . . . . . . . . . . . . CODE Adventura . . . . . . . . . . . . . . . . . . 01 Aiko . . . . . . . . . . . . . . . . . . . . . . . 09 Aiwa . . . . . . . . . . . . . . . . . . .
UL TRA TEC OSD 34 SETUP CUSTOMIZE VIDEO AUDIO THEATER 1. Press MENU on the remote control to display the different features on your HIT ACHI Projection TV . 2. Press the THUMB STICK to highlight a dif ferent feature. 3. Press EXIT on the remote control to quickly exit from a menu.
UL TRA TEC OSD 35 SETUP CUSTOMIZE VIDEO AUDIO THEATER SET UP 1. MENU LANGUAGE Choose English, French, or Spanish text. 2. PLUG & PLA Y Optimum hook up for your system. 3. SIGNAL SOURCE Select Antenna or Cable TV . 4. AUTO CHANNEL SET First time set up for channel buttons.
SET UP 36 SET UP Select SETUP when setting your TV up for the first time. Use the THUMB STICK or on the remote to highlight the function desired. NOTE: To see an auto-demonstration of the on-screen displays with HELP text displayed, press and hold the POWER button on the TV set for approximately five seconds.
SET UP 37 SET UP This graphic guide function will help you to properly set up your TV or Home Theater System. Simply answer three questions and a graphic will be displayed, showing you the optimum setup for your personalized system. Press THUMB STICK or to highlight the correct answers to all three questions.
SET UP 38 SET UP Select ANTENNA if you are using an indoor or outdoor antenna. Select CA TV if you have cable TV . Press THUMB STICK or to highlight and select the correct SIGNAL SOURCE mode. Press EXIT to quit MENU or THUMB STICK to return to previous menu.
SET UP 39 SET UP This feature will automatically store active TV channels in CHANNEL MEMORY . This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ). If the EXIT button is pressed while the AUTO CHANNEL SET function is engaged, programming will stop.
SET UP 40 SET UP Use this function after AUTO CHANNEL SET to add or erase additional channels to the remote control CHANNEL or buttons. Add or erase additional channels while still in CHANNEL MEMORY using CHANNEL or or the number buttons to change the channel.
SET UP 41 SET UP This function allows you to review which channels are labeled in CHANNEL ID (ID.), which have been added to CHANNEL MEMORY (SCAN), and which are protected by P ARENT AL CONTROL (LOCK). Press THUMB STICK or to review more channels.
SET UP 42 SET UP The time must be set before you can use the 4 EVENT PROGRAM or TV TIME OUT . Use THUMB STICK or to set the time, date, and year . Press THUMB STICK or to change position. Press EXIT to quit menu or THUMB STICK to return to previous menu when the CURSOR is in the first position.
SET UP 43 SET UP This feature allows you to adjust Picture Rotation. Use THUMB STICK or to adjust Picture Rotation right or left. Press EXIT to quit menu or THUMB STICK to return to previous menu when the CURSOR is in the first position.
SET UP 44 SET UP The COMPONENT SET function is very useful when setting up reception High Definition, Standard Definition and NTSC signals. Press THUMB STICK or to highlight then press down on THUMB STICK to select Color System (HDTV , SDTV/DVD) Press EXIT to quit menu or THUMB STICK to return to previous menu.
CUST OMIZE CUSTOMIZE 45 CUSTOMIZE This selection contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 channels a name when CA TV signal source is selected.
CUST OMIZE 46 CUSTOMIZE Use this feature to give a name to any of the three video inputs. Press THUMB STICK to highlight VIDEO LIST . Press THUMB STICK to select preset VIDEO LIST . Press THUMB STICK or to scroll through the preset VIDEO LIST .
CUST OMIZE 47 CUSTOMIZE This function allows you to group your favorite channels into six personalized categories that you can rename. A total of 36 channels can be stored in the F AMIL Y F A VORITES function. Channel stored with AUTO CHANNEL SET will automatically be stored in F AMIL Y F A VORITES.
CUST OMIZE 48 CUSTOMIZE Use this function to display F AMIL Y F A VORITES selections as sub-pictures or to tune the main picture to a desired favorite channel. Select a category using THUMB STICK or . Press MENU and the category will be displayed as sub-pictures at the right edge of the screen.
CUST OMIZE 49 CUSTOMIZE This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled amount of time that you set. The code to enter P ARENT AL CONTROL is a four digit secret code number .
CUST OMIZE 50 CUSTOMIZE This function will automatically turn the TV on and of f, one time only , every day , or once a week. Press THUMB STICK to select PROGRAM 1, 2, 3, or 4. Press THUMB STICK or to select the time the TV will turn on and of f.
CUST OMIZE 51 CUSTOMIZE Use this function to automatically turn the TV on and tune to VIDEO: 1, 2 or 3 when it detects a VIDEO input. Use THUMB STICK to select Video Input. Use THUMB STICK or , then press down on THUMB STICK to change AUTO LINK setting.
CUST OMIZE 52 CUSTOMIZE DISPLA Y : ON/OFF will turn the display on or off. MODE: C.C. (Closed Caption) is for the program you are viewing. TEXT is for additional information such as news reports or a TV program guide. This information covers the entire screen and viewing the TV program is not possible.
CUST OMIZE 53 CUSTOMIZE FIRST TIME TOUR This function introduces you to the First Time T our Setup Feature, showing you basic TV functions as well as helping you set up your TV or Home Theater System. This feature will be displayed every time your TV is turned on, unless you set FIRST TIME TOUR to OFF .
VIDEO 54 VIDEO VIDEO Select VIDEO to adjust picture settings and improve picture quality . Use this function to change the contrast between black and white levels in the picture. Use the THUMB STICK or to highlight the function to be adjusted.
VIDEO 55 VIDEO Y our HIT ACHI color TV has the following functions which will adjust picture settings to produce the highest quality picture possible. Use THUMB STICK or to select function. Press down on THUMB STICK to select the function setting.
AUDIO 56 AUDIO Select AUDIO to adjust the TV to your preference and to improve the sound quality . AUDIO This function controls the low frequency audio to all speakers. Use THUMB STICK or to highlight the function to be adjusted. Press THUMB STICK or to adjust the function.
AUDIO 57 AUDIO Use ADV ANCED SETTINGS to improve the sound performance of your TV , depending on listening conditions. MTS MODE Multi-Channel T elevision Sound will allow you to select STEREO (a stere.
THEA TER 58 THEATER Use THUMB STICK or to change THEA TER MODES settings. When TV mode is chosen, the following are automatically set: CONTRAST - 83%, COLOR TEMPERA TURE - COOL, LOUDNESS - ON, PERFECT VOLUME - ON, SRS - OFF .
THEA TER 59 AUDIO Based on the principles of the human hearing system, SRS technology delivers and exciting and realistic 3D Sound experience from just two external speakers (or) the two internal speakers of your HIT ACHI T elevision.
60 CARE OF YOUR HIT ACHI COLOR TV AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty .
61 RECEPTION PROBLEMS ¥ IGNITION NOISE: Black spots or horizontal streaks may appear , picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. ¥ GHOSTS: Ghosts are caused by the television signal following two paths.
USEFUL INFO 62 HIT ACHI Color T elevision incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR T O HA VE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1.
USEFUL INFO 63 Features: ¥ Superfine Picture Quality 700 Line Horizontal Resolution ¥ Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment.
USEFUL INFO 64 Hitachi America, L TD. Home Electronics Division 1855 Dornoch Court San Diego, CA 92154 Hitachi America, L TD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit.
65 NOTES.
66 NOTES.
NOTES 67.
QR48441.
Ein wichtiger Punkt beim Kauf des Geräts Hitachi 32UDX10S, 36UDX10S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hitachi 32UDX10S, 36UDX10S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hitachi 32UDX10S, 36UDX10S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hitachi 32UDX10S, 36UDX10S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hitachi 32UDX10S, 36UDX10S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hitachi 32UDX10S, 36UDX10S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hitachi 32UDX10S, 36UDX10S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hitachi 32UDX10S, 36UDX10S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hitachi 32UDX10S, 36UDX10S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
