Benutzeranleitung / Produktwartung HD 4350 des Produzenten HIS
Zur Seite of 32
ATI Radeon HD 4300 Series User Guide Part Number: 137-41588-10 Rev B.
© 2008 Advanced Micro Devices Inc. All rights reserved. The contents of this document are provided in connection with Advanced Micro Devices, Inc. (“AMD”) products.
Important Safety Instructions Note: This product is for use only with compatible UL-listed personal computers that have installation instructions detailing user installation of this class of product. Read all instructions before beginning installation.
Note to CATV System Installer This reminder is provided to call the CATV systems installer’s attention to Section 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as is practical.
Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Waste Electrical and Electronic Equipment (WEEE) Directive Compliance . . . . . . . . . . . . . . . . . . . 24 VCCI Class B ITE Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 MIC Certification Information .
Chapter 1 Installation For support, you will need to record the serial number and the part number for the card before installation. Installation Overview The installation of the card has slightly different procedures depending on whether you are replacing an existing card or installing a graphics card in a PC for the first time.
Record the Serial and Part Numbers Write down the serial number and part number before installing. The serial number and 102 part number on the graphics card are required for registration and free support. They are located on a sticker on the back of the card.
Uninstalling the Old Driver (Windows Vista®) Follow these steps to uninstall the existing graphics card driver in preparation for installation of a new card. 1. With the current graphics card still in the computer, close all open applications. 2. Click Start ▷ Control Panel .
4. Remove any existing graphics cards from the computer. Warning: Some graphics cards can get hot while operating. Wait approximately five minutes after turning off the computer before touching the card. 5. Locate the appropriate bus slot on the motherboard.
10. Turn on the monitor and then the computer. The computer should start normally and the software must be installed next. Installing the ATI Catalyst™ Software Suite (Windows OS) To install or remove software, you must have administrator rights or be logged on as a user with administrator rights.
Display Configuration This section describes how to configure the display and lists the available display connections. Configure the Display (Optional) If you are not experiencing any troubles with the display, no adjustments are necessary. 1. Right-click on the desktop and, in the shortcut that appears, click Properties .
f. Click OK . Connections The following figure shows the possible connection types on the ATI Radeon graphics card. Available connections may vary between models of this series graphics card.
Adapter Description DVI-to-VGA DVI-to-HDMI™ DVI-to-YPrPb (for a component cable connection to a LCD or plasma TV) 7-pin S-Video cable for video signals 7-pin HDTV output cable Supported Display Connections The graphics card provides hardware support for DVI-I monitors, and HDMI HDTVs (using a DVI-to-HDMI adapter).
Table 1–1 Display Configurations Display Connections CRT analog display • VGA connection • DVI-I-to-VGA adapter LCD display • DVI-I connection and DVI cable • DVI-I connection and DVI-I-to-V.
10 Installation ATI Radeon HD 4300 Series © 2008 Advanced Micro Devices, Inc..
Chapter 2 ATI CrossFireX™ Technology ATI CrossFireX Introduction ATI CrossFireX technology harnesses two or more GPUs (graphics processing units) to be used in a single computer to run up to 2 displays, creating a high- performance gaming platform.
2. Unplug the computer power cord and disconnect the monitor cable from the back panel of the computer. Caution: To avoid possible damage to the motherboard, wait approximately 20 seconds after unplugging the power cord before disconnecting a peripheral or removing a component from the motherboard.
Figure 2–1 ATI CrossFireX Installation 7. Fasten the graphics cards securely to the back panel. 8. Make sure the cables are not interfering with anything inside the computer (for example, a cooling fan) and then replace the computer cover. 9. Reconnect any cables you have disconnected and plug in the computer power cord.
3. Select the Enable CrossFire™ check box. 4. If your system has more than two ATI CrossFireX-capable graphics cards, the dialog appears where you must select the graphics card that will partner with the Master GPU. Note: Enabling ATI CrossFireX for the selected graphics card automatically disables GPU Accelerated Physics for that same card.
Chapter 3 Reference The following section offers troubleshooting tips and provides customer care, warranty, and compliance information. System Requirements Hardware Minimum requirements are: • Motherboard with one PCIe ×16 lane graphics slot. • AMD Athlon™ or Intel® Pentium® 4 CPU.
• A second ATI CrossFireX graphics card compatible with the ATI Radeon HD 4300 Series. (In most cases, a third card and fourth card may be installed, if desired.) • For two card setup, a PCIe 475 watt or higher power supply. • For three card setup, a PCIe 525 watt or higher power supply.
Table 3–1 ATI Catalyst Control Center Access Routes Access Route Instructions Windows Desktop 1. Right-click anywhere on the desktop. 2. From the shortcut menu that appears, click ATI CATALYST(TM) Control Center . Windows Start Menu 1. Click Start on the Windows task bar.
Troubleshooting Graphics Card Installation Troubleshooting For more advanced troubleshooting information, contact AMD Customer Care for ATI products at ati.amd.com . The graphics card doesn't fit any of the motherboard slots. The graphics card needs to be exchanged for one with a bus that matches the motherboard.
Troubleshooting ATI CrossFireX The following are suggested solutions for common ATI CrossFireX troubleshooting issues. Change Motherboard BIOS Settings Some motherboards may have a system BIOS option to switch between single and dual PCIe slot support.
• Check that the interconnect cable is installed correctly. • Close all running 3D applications. • Re-install the ATI Catalyst Control Center and drivers. Screen Rotation is Unavailable or Does Not Work Screen rotation is not an available feature on ATI CrossFireX systems.
The entire display is not visible. If the component input device supports it, try 720p mode. The display appears tilted. Consult the HDTV documentation. The CRT display is green. The system is in component output mode. Restart the computer with only the CRT monitor connected.
result of the product, whether your product contains a defect, and whether your product is under warranty. • AMD Customer Care is unable to assist with refunds, returns, or exchange- specific inquiries.
• Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
To meet UL safety requirements, the computer’s maximum room temperature should not exceed 40 °C. Waste Electrical and Electronic Equipment (WEEE) Directive Compliance VCCI Class B ITE Compliance In.
BSMI Certification Information BSMI Certification Information 25 © 2008 Advanced Micro Devices, Inc. ATI Radeon HD 4300 Series.
26 Reference ATI Radeon HD 4300 Series © 2008 Advanced Micro Devices, Inc..
Ein wichtiger Punkt beim Kauf des Geräts HIS HD 4350 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie HIS HD 4350 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für HIS HD 4350 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von HIS HD 4350 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über HIS HD 4350 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon HIS HD 4350 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von HIS HD 4350 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit HIS HD 4350. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei HIS HD 4350 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
