Benutzeranleitung / Produktwartung HGS24S des Produzenten Hawking Technology
Zur Seite of 27
Please place main product photo here. 1.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim itations are designed to provide reasonabl e protection against harmful interference in a residential installation.
Unpacking the Switch 4 Introduction 1.1 General Description 5 1.2 Gigabit Ethernet Technology 5 1.3 Features 6 1.4 Front Panel 6 1.5 Rear Panel 7 Installation 2.1 Desktop Installation 8 2.2 Rack-Mount Installation 8 2.3 Installing Network Cables 9 2.4 Network Application 9 Description of Functions 3.
The complete HGS24S package consists of: • One HGS24S 24-Port 10/100/1000M Web-Smart Switch • Rack mount kit: 2 mounting brackets and screws • Four rubber feet with adhesive backing • One AC p.
1.1 General Description The device is a 24-port 10/100/1000Mbps Ethernet Web-Smart Switch. Compared with traditional 10/100Mbps Ethernet, the switch de livers a dedicated Gigabit connection to every attached client with no congestion issues.
1.3 Key Features • 24 fixed 10/100/1000Mbps Gigabit Ethernet ports • Provides Auto-discovery Function for easy network management • Provides 8K MAC address entries • 24 groups VLAN table • S.
Wiring for 10/100/1000Mbps (Copper) Below is the summary of the cabling required: Media Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Category 5 UTP/STP 10/100/1000Mbps copper 1000Mbps Category 5.
This switch can be placed directly on your desktop, on the floor , or mounted in a rack. Users can immediately use m o st of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to be put on a clean, fl at desk or table close to a power outlet.
2.3 Installing Network Cables Station Connections Refer to the wiring statement of the previous section; connect each station/device to the switch with the correct cables. Switch-to-Switch Connections In making a switch-to-switch connection, using every port to connect another switch or backbone is strongly recommended.
3.1 PHY Monitoring and Port Mode Setup One of the software’s major tasks is to continuously monito r the PHYs in order to set up the switch ports according to whether the link is up or down, and in the latter case, what the current speed, duplex mode and pause capabilities are.
This section instructs you on how to enter and set up the configurations, which can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Telnet sessi on / Internet Browser over the network (in-band). Factory Default value: IP: 192.168.
In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should conf igure the ma nagement station with an IP address and subnet mask compatible with your switch. 1. Run your Web Browser and enter the IP address “192.
4.2 Homepage On the Home page, you can select what you would like to configure by clicking the menu tabs located at the top of the homepage. They include: • System • Ports • VLANS • Aggregatio.
To restore the default values of switch, click the “ Default ” button at the top of the homepage. If you want to reboot the switch, click the “ Reboot ” Button. To check the connection status of each port, from 1 to 16, take a look at the port monitor.
4.2.1 System To set up the system configurations such as login values, time-out values, and for enabling the VLAN Management: Items Functions Mac Address The Mac Address of the switch S/W Version To look up the Software Version, see here. H/W Version The Hardware version Inactivity Timeout (Secs) Set the console inactivity timeout in seconds.
Note: After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP Address with your browser. 4.2.2 Ports On this page, you can view the port status, set up the speed “Mode” and enable the “FDX Flow Control”.
Items Functions Link Shows the status of each port. When it is red, it means the connection is down. Otherwise, it is green. Mode Choose the Speed mode of port: 10/100/1000, Half/Full. To disable the port, choose “Disable”. If you set to auto-speed, it will be auto- negotiation.
PVID When the VLAN-enabled switch receives a tagged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Functions Port Port Number 1~16 PVID Port VLAN ID Aware To enable the PVID checking and inserting of one port, select “AWARE” Only Tagged Block the untagged frame.
19.
4.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, put the port numbers into th e same Aggregation group line. There are eight groups that can be made. Do not forget to click the “Apply” to save th e settings. The maxim um number of ports for one group is 8.
4.2.5 Qos There is one mode of Quality of Service to choose: custom TOS. 4.2.5.1 Quality of Service (QoS) TOS Configuration To improve the network performance by applying the TOS, set up the priority of eight groups of precedence bits on this page. There are two types to choose, high or low.
4.2.5.2 QoS Port Shaper To control the port data’s flow rate, select “Enable” a nd enter the value you need from 250 - 1000000Kbps. Any packet size that is larger than the limit will be discarded.
4.2.5.3 QoS Port Policer To control the port data’s flow rate, select “Enable” and enter the Value you need from 250 - 1000000K bps. If the packet size that is larger than the limit, the switch will make the asso ciated client suspend the frame transmission by using back pressure or pause frame.
4.2.6 Mirror Port mirror is used to mirror traffic from a source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simultaneously to 1 Monitor port (target port). (N ote that the target port must be in the same VLAN as the source port.
4.2.7 Statistics To check the status of port traffic, click the “Statistic” tab. You can click the “ Clear ” button to erase all records or click “ Refresh ” to show the most current status.
4.2.9 Default To restore to default values, 1. Click the default button on the homepage. 2. Click “Yes” to restore default values. Do not power off the switch while it is working. 4.2.10 Reboot To reboot the switch, 1. Click the “Reboot” button on the homepage 2.
Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN interoperability IEEE802.
Ein wichtiger Punkt beim Kauf des Geräts Hawking Technology HGS24S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hawking Technology HGS24S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hawking Technology HGS24S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hawking Technology HGS24S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hawking Technology HGS24S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hawking Technology HGS24S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hawking Technology HGS24S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hawking Technology HGS24S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hawking Technology HGS24S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
