Benutzeranleitung / Produktwartung 42827 des Produzenten Harbor Freight Tools
Zur Seite of 17
GEARED HEAD DRILL / MILL MACHINE 42827 SET UP AND OPERA TING INSTRUCTIONS Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our website at: http://www .harborfreight.com Read this material before using this product.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 2 SPECIFICA TIONS INCLUDED ACCESSORIES 5 and 6mm Hex W renches Draw Bar R-8/JT2 Chuck 14 / 17mm Open End W rench Slotted Screwdriver Head W rench FEA TURES 1. This machine may be used for surface cutting, drilling, milling, and tapping.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 3 SAFETY W ARNING & CAUTIONS READ ALL INSTRUCTIONS BEFORE USING THIS T OOL! 1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries. 2. OBSER VE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 4 14. ST A Y ALER T . W atch what you are doing. Do not operate this machine when you are tired. 15. DO NOT OPERA TE THIS MACHINE WHILE UNDER THE INFLUENCE OF ALCOHOL, DRUGS, OR PRESCRIPTION MEDICINES.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 5 FEA TURES AND CONTROLS OF THE #42827 DRILL / MILL MACHINE 1. Column 2. Head Collar 3. Head Collar Lock Bolt 4. Head Crank 5. Lock Nut 6. Oil Drain Plug 7. T able Feed Wheel 8. T ravel Stop 9.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 6 UNP ACKING AND INST ALLA TION 1. Remove protective crating and skids carefully . In the event of damage in transit, contact Harbor Freight T ools immediately .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 7 BASIC OPERA TION Prior to Operation 1. Check the oil level, and if necessary ll to the mid point of the oil level window . Basic Controls Please r efer to Figur e 1 on page 5. 1.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 8 Preparing for Milling 1. Adjust the positive stop gauge to its uppermost position. 2. Using the spindle feed handle, adjust the bit to approximately the correct height. T ighten the knob in the center of the spindle feed handle (#16).
SKU 42827 For technical questions, please call 1-800-444-3353. Page 9 Installing and Changing T ools W A R N I N G : T urn off t h e p o w e r an d unplug t h e m a c h in e b e f o r e i ns t a l l i n g o r c h a n g i n g t o ol b i t s . Removing Face Mill or Drill Chuck Arbor 1.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 10 Additional Safety Rules for Drilling and Milling 1. Be sure the drill bit or cutting tool is securely locked in the chuck. 2. Be sure the chuck key is removed from the chuck before turning on the power .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 1 1 The spindle bearing is very hot. 1. There is insufcient lubrication. T urn off the power , and check the bearing for lubrication. If necessary , apply a medium weight bearing grease.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 12 NOTICE: 1 10 V olt systems deliver highly energetic curr ents which ar e capable of causing lethal injury . Do not operate this machine without rst obtaining professional installation and safety inspection to pr event operator injury .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 13 PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE P AR TS DIAGRAM IN THIS MANUAL AS A RE.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 14 GEARED HEAD DRILL MILL MACHINE, HEAD P AR TS LIST Please refer to Parts Diagrams on Page 16 and 17 Part Description Qty .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 15 DRILL MILL MACHINE, P ARTS LIST Please refer to Parts Diagrams on Page 16 and 17 REV 09b Part Description Qty .
SKU 42827 For technical questions, please call 1-800-444-3353. Page 16 VER TICAL MILLING MACHINE, HEAD P ARTS DIAGRAM Please refer to Parts List on Pages 14 and 15.
SKU 42827 For technical questions, please call 1-800-444-3353. Page 17 VER TICAL MILLING MACHINE, BASE P ARTS DIAGRAM Please refer to Parts List on Page 15.
Ein wichtiger Punkt beim Kauf des Geräts Harbor Freight Tools 42827 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Harbor Freight Tools 42827 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Harbor Freight Tools 42827 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Harbor Freight Tools 42827 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Harbor Freight Tools 42827 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Harbor Freight Tools 42827 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Harbor Freight Tools 42827 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Harbor Freight Tools 42827. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Harbor Freight Tools 42827 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.