Benutzeranleitung / Produktwartung G0486/G0487 des Produzenten Grizzly
Zur Seite of 76
COPYRIGHT © APRIL 2006 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
.
T able of Co nten ts INTRODUCTION ............................................................................................................................... 3 Foreword ..............................................................................
-2- G0486/G0487 Wide Belt Sander SECTION 7: SERVICE .................................................................................................................. 27 Table Calibration ...............................................................
G0486/G0487 Wide Belt Sander -3- If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines.
-4- G0486/G0487 Wide Belt Sander Con trol Pa nel F eat ure s Ex tern al F eat u res A. Digital Amp Draw Meter B. Table-Height Digital Readout C. Table Up Key D. Table Down Key E. Sanding Belt Start Button F. Conveyor Belt Start Button G. Power Light H.
G0486/G0487 Wide Belt Sander -5- In ter nal Fea t ures A. Belt Tension Knob B. Platen Adjustment Lever C. Platen Adjustment Lock Lever D. Lock Post Release Lever E. Tracking Adjustment Knob Figure 4. Inside the left access door. F. Upper Rollers G. Airflow Adjustment Knob H.
-6- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -7- .
-8- G0486/G0487 Wide Belt Sander 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. DO N OT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts.
G0486/G0487 Wide Belt Sander -9- 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area.
-10- G0486/G0487 Wide Belt Sander A ddi ti on al Safe t y for Wide Belt Sanders 1. INFEED/OUTFEED AREA. When feeding the workpiece into the machine, keep clear of kickback path. 2. WORKPIECE FEEDING. Never force the workpiece into the sander, and feed only one workpiece at a time.
G0486/G0487 Wide Belt Sander -11- The following list outlines the electrical phase and voltage required to operate the Model G0486/ G0487, as well as the amperage draw of their motors and circuit requirements. Note: If you do not have three-phase power avail- able, you will have to install a phase converter such as the Griz zly Phase Converter.
-12- G0486/G0487 Wide Belt Sander 4 40 V Con necti on Figure 7. 440V connections, Model G0486/ G0487. 6. Wire the sanding belt, conveyor belt, and table elevation motors as shown on the diagrams on the inside of each motor wire cover, or refer to Motor Wiring on Page 47.
G0486/G0487 Wide Belt Sander -13- In ve nt or y Un packi ng Y our wi de belt sander w as carefully packed when it left our w arehouse. If you discove r the ma chine is damaged af ter you hav e signed for deliver y , please im medi ately c all Customer Servic e at ( 5 70) 546 - 96 63 for advice.
-14- G0486/G0487 Wide Belt Sander Hard w are Ch ar t.
G0486/G0487 Wide Belt Sander -15- Si te Con sidera ti on s Fl oo r Loa d Refe r to the M achine D ata She et for the weight and footpr int s pec ific ation s of your machin e. Some resid ential floors may require additio nal reinfo rcement to suppor t both the machine and operator .
-16- G0486/G0487 Wide Belt Sander To install the air line: 1. Connect the hose from your air compressor to the air inlet ( Figure 11 ) on the regulator. Air Inlet Air ON/OFF Lever (Open Position) Regulator Knob 2. Make sure the red handle on the regulator is in the open position (parallel with the air inlet).
G0486/G0487 Wide Belt Sander -17- To install the sanding belt: 1. DISCONNECT THE SANDER FROM THE POWER SOURCE AND REMOVE AIR PRESSURE COMPLETELY ! 2. De-activate the belt tension piston by turning the belt tension knob ( Figure 14 ).
-18- G0486/G0487 Wide Belt Sander P ressu re Ro ller s It is absolutely essential to keep the pres- sure rollers set below the level of the sand - ing roller. If the pressure rollers are even, or higher than the sanding roller, the wood WILL be propelled from the sander at a high rate of speed.
G0486/G0487 Wide Belt Sander -19- Reco mmen d ed A dj us tments For your convenience, the adjustments listed below have been performed at the factory and require no further adjustment. However, we rec - ommend that you verify that the adjustments are correct and to your satisfaction.
-20- G0486/G0487 Wide Belt Sander Ch oo si ng Sand paper Operati on S af ety Your safety is important! Please follow the warnings below during this entire section: The grit you choose will depend on the type of work, the species of wood and the stage of finish - ing.
G0486/G0487 Wide Belt Sander -21- T able Mo v emen t The table height can be adjusted manually or with the digital key pad and motor (see Figure 16 ). Manual Table Movement: Turn the handwheel located under the front of the infeed table for manual table positioning.
-22- G0486/G0487 Wide Belt Sander Am p Dra w M eter The amperage draw meter ( Figure 18 ) is located above the control panel. Use the meter to monitor the amperage draw on the machine while per- forming sanding operati ons. As a general rule, always start with a small load and work your way up.
G0486/G0487 Wide Belt Sander -23- Sand in g W or k piece Typically, no more than 0.5mm (approx. 1 ⁄ 64 ") of material is removed during each pass. Attempts to remove too much material can cause jamming, wood burning, rapid sandpaper wear or tearing, poor finish, short motor life, and belt slippage.
-24- G0486/G0487 Wide Belt Sander Figure 21. Sanding belt cleaning pad. H2845—Cleaning Pads Cleaning pads are the perfect accessory for wide belt sanders. Simply set the conveyor table to height and feed the pad through to “unload” a dirty sanding belt.
G0486/G0487 Wide Belt Sander -25- Disconnect power to the machine when perform - ing maintenance, assem - bly or adjustments. Failure to do this may result in serious person - al injury. We ek ly Grease the grease fittings located on the feed belt roller axles and the sanding belt roller axles with Gear Lube-2 (GL-2) or automotive grease.
-26- G0486/G0487 Wide Belt Sander Dus t and W ater T ra ps There are three collection traps on this wide belt sander. One water trap is attached to the bottom of the air regulator, and two dust traps are attached on the air diaphragm assemblies.
G0486/G0487 Wide Belt Sander -27- T able Cal ibra ti on NOTICE The digital thickness gauge has been cali- brated at the factory and should require no further adjustment. However, we recom - mend verifying its accuracy. Use the first board fed through the sander to test the accuracy of the digital thickness gauge.
-28- G0486/G0487 Wide Belt Sander To replace the brake pads: 1. DISCONNECT THE SANDER FROM THE POWER SOURCE AND REMOVE AIR PRESSURE COMPLETELY! 2. Remove the nuts from the two mounting bolts and the two snap rings on the mounting pins behind the bracket.
G0486/G0487 Wide Belt Sander -29- Os ci ll ati on Tim in g When the oscillation is correctly adjusted, the sanding belt oscillates to the left and to the right at the same speed. If the sanding belt makes contact with a limit switch, as shown in Figure 26 , the emergency braking system will activate and stop the sander immediately.
-30- G0486/G0487 Wide Belt Sander 5. Tighten the lock nut ( Figure 28 ) to secure the airflow adjustment knob. 6. Restrict the airflow across the air fork gap with a scrap piece of wood. You should notice the roller pivot to the right. When the stick is removed, the roller should pivot back to the left.
G0486/G0487 Wide Belt Sander -31- NOTICE The table has been adjusted at the fac- tory and should require no further attention. However, we recommend verifying that it is parallel with the sanding roller. The oscillation speed of the sanding belt is adjustable.
-32- G0486/G0487 Wide Belt Sander To adjust the table parallelism: 1. Pass the widest size board your machine will allow through the sander until the entire sur- face of the board is making contact with the sanding belt. 2. Measure the thickness of the board at vari- ous points around the edge.
G0486/G0487 Wide Belt Sander -33- Figure 34. Pressure roller adjustment location. 6. Loosen the infeed pressure roller lock nuts ( Figure 34 ) on the infeed pressure roller. Turn the adjustment studs ( Figure 34 ) to lower the infeed pressure roller until it just touches the boar d.
-34- G0486/G0487 Wide Belt Sander 7. Insert two 2x4 x 8' wooden studs under the table to support the table, and then (with help) lift the table slightly and move it out of the rear of the machine. 8. Disconnect the limit switch, remove all mount- ing screws, and remove the emergency stop push-panel assembly .
G0486/G0487 Wide Belt Sander -35- .
-36- G0486/G0487 Wide Belt Sander NOTICE Adjust the feed belt tension before adjusting the feed belt tracking. F eed Belt T en si on F eed Belt T ra ck in g To adjust the feed belt tracking: 1. Turn the feed belt ON . 2. If the feed belt is tracking to the right side of the table, turn the right adjustment bolt ( Figure 39 ) clockwise.
G0486/G0487 Wide Belt Sander -37- I. Oscillation Timing Piston and Diaphragm Assy. J. Oscillation Speed Control Piston K. Belt Tension Control Piston L. Belt Tension Control Switch M. Emergency Stop Button Switch N . Emergency Stop Push Brake Switch O.
-38- G0486/G0487 Wide Belt Sander T ro ubles hoo ti ng Revie w the troublesho oting and procedures in this section to fix y our machine if a problem dev elops. If you need replacement par ts or you are unsure of your repair skills, then feel free to c all our T e chnical Suppor t at ( 57 0 ) 5 46 - 96 63.
G0486/G0487 Wide Belt Sander -39- T ro ubles hoo ti ng Fo r yo ur s af et y , tu rn t he power switch off and dis - connect the sander from the power source and the air supply before starting the applicable troubleshooting. Symptom Possible Cause Possible Solution Lines across width of workpiece.
-40- G0486/G0487 Wide Belt Sander Control Panel Component Locations (G0486/G0487) Sanding Belt STOP Button Conveyor Belt STOP Button Emergency Stop Button Sanding Belt START Button Conveyor Belt START.
G0486/G0487 Wide Belt Sander -41- .
-42- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -43- Wi ri ng Bo x Com ponen ts ( G0 4 8 6 220 V / 4 40 V , G0 4 87 4 4 0 V ) Conveyor Motor Contactor Emergency Brake Contactor UP/DOWN Table Motor Contactors Conveyor Mo.
-44- G0486/G0487 Wide Belt Sander Wi ri ng Bo x E lectr ica l Dia gra m ( G0 4 87 2 20 V ) .
G0486/G0487 Wide Belt Sander -45- Wi ri ng Bo x Com ponen ts ( G0 4 87 2 20 V ) Transformer Sanding motor Start Delay Main Junction Block Sanding Motor Overload Relay Conveyor Motor Overload Relay Two.
-46- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -47- .
-48- G0486/G0487 Wide Belt Sander T ool Bo x and A cces so r ies Dia gra m 0 0 0 0 S eries Part s.
G0486/G0487 Wide Belt Sander -49- T ool Bo x and A cces so r ies P ar ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH29330001 PLATEN REMOVAL TOOL 7-2 P04860007-2 SANDING BELT #180 (43".
-50- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -51- Sand in g Mot or Sy stem P ar ts L is t REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P05811101 MACHINE FRAME (G0486) 127 P04861127 LIMIT SWITCH PLATE 101 P048711.
-52- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -53- T able Li f t Sy st em Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P04862101 ELEVATION SCREW 319 PB07 HEX BOLT 5/16-18 X 3/4 102 PB03 HEX BOLT 5/1.
-54- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -55- Con v e y or Sy st em P ar ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P05813101 CONVEYOR TABLE (G0486) 124 PLW06M LOCK WASHER 10MM 101 P04873101 CONVEYOR TABLE (G0487) 126 P04863126 TIMING BELT 1422V-290 102 P05813102 CONVEYOR BELT (G0486) 127 PSB64M CAP SCREW M10-1.
-56- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -57- F eed, Dru m, an d Pre ss ure Rol ler Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 103 P04864103 COMPRESSION SPRING 302 P04864302 MIDDLE PISTON BRACKET.
-58- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -59- Sand in g Dru m and P lat en Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P04865101 BEARING HOUSING 305 PS01 PHLP HD SCR 10-24 X 1/2 102 P05815102 .
-60- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -61- Upper Ro l ler Sy stem P ar ts L is t REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P04866101 SQUARE FRAME REAR (G0486) 131 PLW01 LOCK WASHER 5/16 101 P04876101 S.
-62- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -63- Cab i net A ssem bl y Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P04867101 UPPER FRAME COVER (G0486) 109 P05817109 RIGHT DOOR, LOWER FRAME 101 P0.
-64- G0486/G0487 Wide Belt Sander Mai n Electr ical Pa nel and Con tro ls Diag ram .
G0486/G0487 Wide Belt Sander -65- Mai n Electr ical Pa nel and Con tro ls Pa r ts L ist REF PART # DESCRIPTION 101 P04868101 ELECTRICAL CONTROL BOX (G0486) 101 P04878101 ELECTRICAL CONTROL BOX (G0487).
-66- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -67- Ai r Sy st em P ar ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PH29339101 FILTER CUP 122 PH29339122 AIR SWITCH 1/8" 102 PH29339102 PRESSURE REGULA.
-68- G0486/G0487 Wide Belt Sander .
G0486/G0487 Wide Belt Sander -69- REF PART # DESCRIPTION REF PART # DESCRIPTION 200 P04869200 MODEL G0486 LABEL 211 P04869211 G0486 AMP SCALE LABEL 200 P04879200 MODEL G0487 LABEL 211 P04879211 G0487 .
-70- G0486/G0487 Wide Belt Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG D OTTED LINE Name _____________________________________________________________________________ Street _____________________________________________________________________________ City ____.
T APE ALONG EDGES - - PLEASE DO N OT ST APLE FOLD ALONG D OTTED LINE FOLD ALONG D OTTED LINE GRI Z ZL Y IN DUST RIAL , IN C. P .O . BO X 20 6 9 BELLING HAM , W A 982 27 -20 6 9 Place Stamp Here N a m .
.
.
Ein wichtiger Punkt beim Kauf des Geräts Grizzly G0486/G0487 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Grizzly G0486/G0487 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Grizzly G0486/G0487 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Grizzly G0486/G0487 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Grizzly G0486/G0487 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Grizzly G0486/G0487 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Grizzly G0486/G0487 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Grizzly G0486/G0487. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Grizzly G0486/G0487 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
