Benutzeranleitung / Produktwartung 313483A des Produzenten Graco Inc.
Zur Seite of 88
Operation - Repair - P ar ts / 操作 - 修理 - 零部件 HTX 2030 - For P ortable Airless and Air -Assisted Sp raying of W ater-Based Arc hitectural Coatings and P aints with Base Coat Pump - - For .
Contents / 目录 2 313483A Contents / 目录 Contents / 目录 . . . . . . . . . . . . . . . 2 W AR NING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 警告 . . . . . . . . . . . . . . . . . . . . . 5 Produc t Overview . . . . .
Warning 313483A 3 Wa r n i n g The f ollowing warnings are f or the setup, use, gr oundi ng, maintenance, and repair of this equipmen t. The exc lamation point symbol alerts y ou to a general warning and the hazar d symbol refe rs to pr ocedure-spe- cific risk.
Warning 4 313483A PRESSURIZED ALUMINUM P ARTS HAZARD Do not use 1,1,1-trichloroethane , meth ylene ch loride, other halogenated h ydrocarbon solv ents o r fluids containing such solv ents in pressu rized aluminum eq uipment.
警告 313483A 5 警告 以下为针对本设备的设置、使用 、接地、维护及修理的警告。惊叹 号标志表示一般性警告，而各种危 险标志则表 示与特定的操作过.
警告 6 313483A 高压铝质部件危险 不要在加压的铝质装置中使用 1,1,1- 三氯乙 烷、二氯甲烷、其它卤代烃 溶剂或含有这些溶剂的流体。 否则会导致剧烈的.
Product Overview 313483A 7 Pr oduct Overview HTX 2030 with Base Coat Pump (257369) The HTX 2030 Spra yer comes equipped w ith a Base Coat Pump 24B321. On ly water- based materials are to be used with .
Product Overview 8 313483A T op Coat Pump (Kit 24B140) The pump on the HT X 2030 Spra yer can also be s witched out wit h a T op Coat Kit 24B140 (purc hased separately) .
产品总览 313483A 9 产品总览 采用底色漆泵的 HTX 2030 (257369) HTX 203 0 喷涂机是装配底色漆 泵 （24B 321）供货的。 该配置只能使用水性涂料，例如 ： • 含.
产品总览 10 313483A 面漆泵 （配件包 24B140） 也可以通过面漆泵配件包 24 B140 （可另行订购） 来关闭 HTX 2030 喷涂机上的泵 。此泵用于低 粘度 涂料，例如.
Component Identification - Sprayer / 部件辨认 - 喷涂机 313483A 11 Component Identification - Spra y er / 部件辨认 - 喷涂机 ti13634a 1 2 3 4 5 7 8 11 10 9 6 T op Coa t Kit / 8 面漆泵.
Component Identification - Base Coat Applicator / 部件辨认 - 底色漆喷涂器 12 313483A Component Identification - Base Coat Applicator / 部件辨认 - 底色漆喷涂器 ti13635a 1 2 3 4 5 6 .
Operatio n / 操作 313483A 13 Operation / 操作 Pressure Relief Pr ocedure / 泄压步骤 Applicator (Base Coat Pump) / 喷涂器 （底色漆泵） English 1. T ur n engine OFF . 2. T ur n on/off s witch OFF and turn pressure con- trol knob fu lly counter- cloc kwise.
Operation / 操作 14 313483A Pressure Relief Pr ocedure / 泄压步骤 Spray Gun (T op Coat Pump) / 喷枪 （面漆泵） English 1. Loc k gun trigger saf ety and tur n engine OFF . 2. T ur n on/off s witch to OFF and tur n pressure control knob fully coun- terclockwise .
Operatio n / 操作 313483A 15 Star t Engine / 起动发动机 English 1. Mov e fuel v alv e to OPEN. 2. Mov e chok e to CLOSED . 3. Set throttle to F AST . 4. Set engine s witch to ON. 中文 1. 将燃油阀推到打开 位置。 2. 将阻风门推到关闭 位置。 3.
Operation / 操作 16 313483A English 5. Pull starter rope. 6. After engine starts, mov e chok e to OPEN. 7. Set throttle to de sired setting. 中文 5.
Operatio n / 操作 313483A 17 Setup / 设置 English 1. Fill mixing pail with pre-mixed texture mate- ria l. Add appro ximately 10% water to texture mix or per mater ial manufac- turer instructions. Mix thoroughly . 2. Connect mate rial hose to pump out- let.
Operation / 操作 18 313483A English 3. P our mixed mat erial into supply pail under spra y er . 4. Place pump suction tube into mix ed mat e- ria l. Prime Pump 1. Star t gasoline engine and adjust spee d to half throttle . T ur n drain v alv e to DRAIN.
Operatio n / 操作 313483A 19 English 3. To p C o a t P u m p : T urn on/off swit ch ON. Base Coat Pump: Tu r n P r i m e switch ON, or activate applica- tor s witch on material hose. 4. Rotate p ressure control knob 1/4 tur n. Run pump until a steady stream of mate- rial flows fro m drain v alv e.
Operation / 操作 20 313483A English Spray Without Air 1. Install filter and tip ex t e n s i o n . 2. Inser t metal seat and OneSeal. Insert Switch Tip . Scre w assembly ont o appli- cator . 3. T ur n drain valv e to SPRA Y , and tur n on/off switch to ON.
Operatio n / 操作 313483A 21 English Spra y Without Air - Clear Clog 1. Rotate Switc hTip to Clear posit ion. Aim applicator at fl oor and turn pump ON. When clog clea rs, tur n pump OFF . 2. Rotate Sw itchTip t o Spra y position. T ur n pump ON. Spra y test pattern.
Operation / 操作 22 313483A English Spray With Air (Base Coat Applicator) 1. Prepare material, page 17. Place material hose in supply pail. 2. T ur n on/off switch OFF . 3. Remo ve cap bef ore installing air line. 4. T ur n air valv e OFF . Connect applicator t o material hose and air hose.
Operatio n / 操作 313483A 23 English 5. T ur n on/off s witch ON. 6. Hold applicator ov er material pail and turn pump ON using appli- cator s witch on hose. 7. T ur n pump con- trol cloc kwise until desired material deliv er y rate is achie v ed. 8.
Operation / 操作 24 313483A English Spray Gun (Top Coat Pump) 1. Loc k gun trigger safety . Inser t seat and OneSeal ™ . Inser t SwitchTip . 2. Screw assemb ly onto gun. Hand ti ghten. 3. T r igger gun and spra y test patter n. Slowly adjust pressure to eliminate heavy edges.
Operatio n / 操作 313483A 25 Cleanup / 清洗 English 1. T ur n on/off s witch OFF . 2. P erf orm Pressure Relief procedure , page 13. 3. Place pum p in pail of clean wa ter . 4. Shut OFF air if spr ay- ing with air . Remove applicator from mate- rial and air hoses.
Operation / 操作 26 313483A English 5. Disconnect material hose from pump outlet. 6. Inser t wet cleaning ball into hose (Ba se Coat Only). Connect mate- rial hose to pump out- let. 7. Hold mate rial hose ov er w aste pail. 8. T ur n on/off swit ch ON.
Operatio n / 操作 313483A 27 English 9. Run pump until clean- ing ball e xits material hose. Sa v e cleaning ball (Base Coat Only). 10. T ur n on/off s witch OFF and turn prime valv e to DRAIN. Clean outside of pump and suct ion tube with brush and wat er.
Operation / 操作 28 313483A English 13. Run pump un til clean water flows from appli- cator . 14. Add addit ional w ater and repeat steps 12 - 13 if nece ssar y . 15. Open dr ain v alv e and turn pr ime switch ON to flush valv e. 16. T ur n on/off s witch OFF .
Operatio n / 操作 313483A 29 English 17. Remo v e and thoroughly clean applicator , spray tips and guard with brush. 18. Clean hard ened material from applicator nozzles with air nozzle cleaner . NO TICE Do not use air nozzle cleaner to clean applicator check v alv e or airless spray tip .
Operation / 操作 30 313483A Digital T racking System (DTS) / 数字跟踪系统 English Main Menu Close cover when spray- ing to protect displa y . 1. P erform Startup steps 1 - 2. • Open drain valv e • T urn pump control counterclockwise to low est se tting • Set applicator s witch to OFF 2.
Operatio n / 操作 313483A 31 English 3. Shor t press DTS butt on to di spla y installed pump . 4. Shor t press D TS but- ton to mov e to Engine RPM. 5. Shor t press D TS but- ton to return to Pres- sure. T o Change Pressure Units: Press and hold (8 seconds) DTS button to change pressure unit (psi, bar , MP a).
Operation / 操作 32 313483A Secondary Menu - Stored Data Mode / 二级菜单 - 所存储的数据模式 English • Open drain v alve • T ur n pump control countercloc kwise to lowest setting • Set applicator s witch to OFF 1. Star t Engine, page 15.
Operatio n / 操作 313483A 33 English 4. Shor t press DTS b ut- ton and date code dis- pla ys. 5. Shor t press DTS but- ton and part number displa ys. 6. Shor t press D TS but- ton and Base Coat hours displa ys. Shor t press DTS but- ton and T op Coat hours displa y .
Operation / 操作 34 313483A English 8. Press and ho ld DTS butt on until CLEAR ERROR NO ERR OR CODE scrol ls through the displa y and erro r code E=00 displa ys . 9. Shor t press DTS but- ton again and SOFT - W ARE REV scrolls through displa y f o l- lowe d by re vision le v el (f or e xample 10 102).
Operatio n / 操作 313483A 35 Digital Displa y Messages * Error codes also appear on control board as a blinking red LED . LED is an alter nate to digital messages. 1 Remo ve tw o screws (71) and s wing down co ver (130). 2 Star t engine. Blink count is the sa me as error co de(E=0X).
Operation / 操作 36 313483A 数字显示信息 * 故障代码也出现在控制板上，用闪烁的红色 LED 指示灯表 示。LED 指示灯是数字信息的一种替代表示。 1 卸下 2 个.
Maintenance / 维护 313483A 37 Maintenance / 维护 English NO TIC E D AIL Y : AFTER FIRST 20 HOURS OF OPERA TION F or detailed e ngine mainte - nance and specifications , ref er to sepa rate Honda Engines Owner’ s Manual (supplied).
Maintenance / 维护 38 313483A English WEEKL Y AFTER EA CH 100 HOURS OF OPERA TION SP ARK PLUG: Engine Oil Funnel: • Remove engine air fil- ter cov er and cle an element. Replace ele - ment if necessar y . If operating in an unusu- ally dusty en vironment, chec k filter daily and replace (if nece ssar y).
Troubleshooting 313483A 39 T r oubleshooting Problem Cause Solution E=XX is displa yed F ault condition e xists Deter mine fault correction from tab le, page 35. Engine will not star t Engine switch is OFF T ur n engine switch ON Engine is out of gasoline Refill gas tank.
Troubleshooting 40 313483A Pump output is low ( Base Coat Pump see pag es 70. To p C o a t P u m p see manual 310894) Strain er (82) is clogged Clean str ainer . Piston ball is not seating Service piston ball. Piston packings are worn or damaged Replace packings .
故障排除 313483A 41 故障排除 故障 原因 解决的办法 显示 E=XX 存在故障情况 根据第 35 页的表格确定故障的纠正措施。 发动机无法起动 发动机开关处于关.
故障排除 42 313483A 泵的输出量低 （ 底色漆泵 参见第 70 页。 面漆泵 参见手册 310894） 过滤器 （82）堵塞 清洗过滤器。 活塞止回球不到位 修理活塞止回.
Repair / 修理 313483A 43 Repair / 修理 Bearing Housing and Connecting Rod / 轴承套和连杆 Re m ova l / 拆除 Relie ve Pressure , page 13. / 释放压力 ，见 第 13 页。 English 1. Remove f our screws (45) and front cover (44). Remov e Pump , page 70.
Repair / 修理 44 313483A Installation / 安装 English 1. Ev enly lubricate inside of bronz e bearing (C) in bearing housing (40) with high-quality motor oil. Liberally pac k top roller bearing (E), lower bearing (D) inside connecting rod (43) with bearing grease.
Repair / 修理 313483A 45 English NO TICE 5. Install scr ews (41) and washers (42) in be ar- ing housing. T orque e venly to 40 ft-lb (54 N•m). 6. Install Pump , page 70. Do not use bearing hous- ing scre ws (41) to align or seat bearing housing wit h drive housing.
Repair / 修理 46 313483A Drive Housing / 驱动室 Re m ova l / 拆除 Relie ve Pressure , pa ge 13. / 释放压力 ，见第 13 页。 English 1. Remo v e Bearing Housing , pag e 43. NO TICE 2. Remov e six screws (38). 3. Lightly ta p around drive housing ( 33) to loosen dr ive housing.
Repair / 修理 313483A 47 Installation / 安装 English 1. Apply all grease sup- plied with replace ment gear cluster to gear teeth and mating sur- fac e s. 2. Ensure thr ust washers (30, 31) are on c ombi- nation gear (32) and washers (33a, 33b) are on crankshaf t of drive housing (33).
Repair / 修理 48 313483A English 5. Install six screws (38). T orque e v enly to 200 ± 10 in-lb (22.6 ± 1.1 N•m). 6. Install Pump , page 70. NO TICE DO NO T use drive housing screws to align or seat drive housing with pinion housing. Align these parts with locating pin s to av oid prematur e bearing wear .
Repair / 修理 313483A 49 Pinion Assembl y / Clutch Armature / Clamp / 小 齿 轮 组 件/离 合 器 电 枢/夹 子 Pinion Assembl y / Clutch Armature Re m ova l / 小齿轮组件 / 离合器电枢的拆除 If pinion assemb ly (29) is not remo v ed from clutch hous- ing (19), perf or m steps 1 through 3.
Repair / 修理 50 313483A English 3. Remove f our screws (36), washers (37 ), and pinion assembly (2 9). 4. Place pinion assembly ( 29) on bench with rotor side up . 5. Remov e f our scre ws (28) and lock w ashers (24). Install two screws in threaded holes (E) in rotor .
Repair / 修理 313483A 51 English Clutch Armature 8. Use an impact wr ench or wedge so mething between clut ch arma- ture (25) and clu tch housing to hold engine shaft during remo v al. 9. Remov e f our screws (23) and loc k washers (24). 10. Remove armat ure (25).
Repair / 修理 52 313483A Installation / 安装 English Clutch Armature 1. La y two stac ks of tw o dimes (or 1.4mm coins) on a smooth bench surf ace. 2. La y armature (25) on two stac ks of coi ns. 3. Press center of hub (26) do wn to bench surf ace.
Repair / 修理 313483A 53 Clamp Remov al / 夹子的拆除 Gasoline can spill and cause a fire or explosion if engine is tipped on its side . 如果发动机侧向翻倒，汽油可能溢出，引起火灾或爆炸。 English 1. Remo v e Engine , page 59, and dra in gasoline from tank according t o Honda manu al.
Repair / 修理 54 313483A Clamp Installation / 夹子的安装 English 1. Install engine shaft ke y (18). 2. T ap clamp ( 22) onto engine shaft (A). Maintain dimension of 2.612 ± .0 10 in. (66.34 ± .2 5mm). Chamf er must f ace engin e. 3. Chec k dimen- sion: Place r igid, straight steel bar (B) across f ace of clutch housing (19).
Repair / 修理 313483A 55 English 6. Check o- ring (29d) and replace if missing or damaged. 7. T ap pinion shaft (29a) in with plastic mallet. 8. Install retaining ring (29b) with be v eled side f acing up . 9. Place pinion assembly on bench with roto r side up .
Repair / 修理 56 313483A English 10. Apply t hread sealant to screws. Install f our scre ws (28) and loc k washers (24). Alter- nately torque screws to 125 ± 10 in-lb (14 ± 1.1 N•m) until rotor is secure. Use threaded holes to hold rotor . 11. Insta ll pinion assem- bly (29) with f our screws (36) and wash- ers (37).
Repair / 修理 313483A 57 Clutch Housing / 离合器外罩 Re m ova l / 拆除 English 1. Remov e f our screws (20) and lock w ashers (21) which hold clutch housing (19) to engine. 2. Remo v e scre w (35) from unde r mounting p late (D). 3. Pull off clutch housing (19).
Repair / 修理 58 313483A Installation / 安装 English 1. Push on c lutch housin g (19). 2. Install four capscrews (20) and lock w ashers (21) and secure clutch housing (1 9) to engine. T orque to 200 in- lb (22.6 N•m). 3. Install scre w (35) from beneath mounting plate (D) .
Repair / 修理 313483A 59 Engine / 发动机 Re m ova l / 拆除 NO TE: All service to the engine must be perf ormed by an aut horized Honda dealer . 注释： 对发动机的所有维修服务必须由本田 （Honda）授权 的经销商进行。 English 1.
Repair / 修理 60 313483A Installation / 安装 English 1. Lift engine caref ully and place on spr a yer car t. 2. Install two screws (16) in base of engine and secure with loc knuts (17). T orque to 26 ft-lb (22.6 N•m). 3. Connect all necessary wiring.
Repair / 修理 313483A 61 Pressure Contr ol / 压力控制器 Pump On/Off Switch / 泵通 / 断开关 Re m ova l / 拆除 English 1. Remo ve tw o scre ws (71) and swing down cov er (70a). 2. Disconnect pump O N/OFF s witch (70j) connector from co n- trol board.
Repair / 修理 62 313483A Installation / 安装 English 1. Install new ON/OFF s witch (70j) so tabs of s witch snap into pl ace on inside of cov er . Align new ON/OFF s witch with electr ical tabs at bott om. 2. Connect pump ON/OFF switch connector to co ntrol board.
Repair / 修理 313483A 63 Contr ol Boar d / 控制板 Re m ova l / 拆除 English 1. Remove two screws (71) and s wing co v er (70a) down. 2. Remov e strain relief bu shings (70b).
Repair / 修理 64 313483A Installation / 安装 English 1. Install control board (70c) with f our scre ws (70d). 2. Connect engin e wires to control board (70c ).
Repair / 修理 313483A 65 Pressure Contr ol T ransducer / 压力控制传感器 Re m ova l / 拆除 English 1. Remov e tw o screws (71) and s wing co v er (70a) do wn. 2. Disconnect tr ansducer lead from control boa rd (70c). 3. Remov e strain relief (70b) and pull tr ans- ducer cable from the control bo x.
Repair / 修理 66 313483A Installation / 安装 English 1. Install o-ring (158b) and pressure cont rol transd ucer (158) in manifold (72). Tighten securely . 2. Place end of trans- ducer in slot of mount (183) and secure wit h cov er (184) and scre ws (182).
Repair / 修理 313483A 67 Pump Contr ol / 泵控制器 Re m ova l / 拆除 English 1. Remov e tw o screws (71) and s wing co v er (70a) do wn. 2. Disconnect pump con- trol (70p) lead fr om control board (70c). 3. Loosen set scr ews on pump contro l knob (70k) and re mov e knob , shaft nut, lock washer and pump con- trol (70p).
Repair / 修理 68 313483A Installation / 安装 English 1. Install shaft spacer (70n) on p ump control (70p). 2. Install pump control, shaft nut, lock washer , and pump contro l knob (70k). a. T ur n pump control shaft clockwise to internal stop . Assem- bl e pump control knob to strike pin on co v er (70a).
Repair / 修理 313483A 69 English 3. Connect pump control lead to contro l board (70c). 4. Swing cover (70a) up and secure with two screws (71). 中文 3.
Repair / 修理 70 313483A Displacement Pump / 活塞泵 Re m ova l / 拆除 English 1. Flush pump , page 25. 2. Stop p ump with piston rod in its low est posi- tion. 3. P erform Pressure Relief procedure, page 13. 4. To p C o a t P u m p : Sep- arate drain hose from spra yer .
Repair / 修理 313483A 71 English 5. Disconnect tr ansducer from pump m anif old. 6. Raise latch lock and push latch open. 7. Ratchet open pu mp door a. Ratche t pump door f orw ard. b . T wis t latch u-bolt out of pump door recess. 中文 5. 从泵歧管上卸下传 感器。 6.
Repair / 修理 72 313483A English c. Place u-bolt on pump door outer edge. d. If pump door is stuc k, do steps e , f , and 8. Otherwise , go to st ep 9. e. T wist latch u-bolt bac k from pu mp door outer edg e. f. Place u-bolt on pump door protru- sion.
Repair / 修理 313483A 73 English 8. Ratchet pump d oor f or- ward . 9. Open pump door . 10. Pull out pump pin and place in pin holder . 中文 8. 用棘齿机构向前推动 泵门。 9.
Repair / 修理 74 313483A Installation / 安装 English 1. Adjust piston rod to proper leng th: Adjust piston rod with pin holder to pull out piston rod. T ap piston rod on hard surf ace to push in piston rod. 2. Push pump collar flush with bearing housing ledge to be ab le to close pump door .
Repair / 修理 313483A 75 English 5. Rotate pum p until transd ucer por t is aligned directly to back of spra y er . Connect transd ucer and hand tighten se curely . NO TE: Clean out ALL media and debris from transd ucer and trans- ducer por t before con- necting tr ansducer .
Parts / 零部件 76 313483A Pa r t s / 零部件 Model 257369 / 型号 257369 190 191 2 17 10 33 133 16 21 40 126 44 75 43 45 110 64 63 38 153 30 31 32 30 33a 33b 29 189 38 27 24 28 122 108 17 107 11.
Parts / 零部件 313483A 77 P arts List - Model 257369 / 零部件清单 － 257369 型 Ref. P art Description Qty . 1 24A852 FRAME, car t, HTX 2030 1 2 156306 W ASHER, fl at 2 3 119509 WHEEL, pneuma.
Parts / 零部件 78 313483A Pressure Contr ol Bo x / 压力控制箱 70c 70b 71 157 120 70b 70b 185 70d 70g 70a 70h 156 70n 70p 156 70p 70m 70k 187 70j 186 70d ti13561a Ref.
Parts / 零部件 313483A 79 Bearing Housing / 轴承套 40 150 151 147 112 111 113 95 40a 40b 148 48 ti13558a Ref. P art Description Qty . 40 24B528 HOUSING, be aring 1 40a† 107251 SCREW , panhead .
Parts / 零部件 80 313483A Base Coat Pump / 底色漆泵 Ref. P art Description Qty . 47 24B321 PUMP , displac ement 1 82 15X762 STRAINER, 2 in. n pt 1 102 24B572 V AL VE, drain, assembly 1 102a 193.
Parts / 零部件 313483A 81 Base Coat Pump (Continued) / 底色漆泵 （续） 202 201 226 225 203 204 227 236 235 223 205 221 205 206 208 207 209 210 219 211 218 212 220 213 217 216 232 215 214 225 225 20 3 210 219 219 ti13560a All parts shown are included in Pump (47) 24B321 所示的所有部件均包括在泵 （47）24B321 中 Ref.
Parts / 零部件 82 313483A T exture Applicator and Hose / 纹理涂料喷涂器和软管 304 305 306 309 307 308 320b 320h 320j 320a 320k 320e 320f 320g 320c 320d 320b 320m ti13660a Ref.
Parts / 零部件 313483A 83 T op Coat Pump Kit 24B140 (Sold Separately) / 面漆泵配件包 24B140 （需另行订购） 427 428 431 429 421 406 413 401 402 410 417 409 411 419 418 420 403 414 404 421a 421b 421 421d 421e 421f ti13562a ti13824a Ref. P art D escription Qty .
Wiring Diagram / 接线图 84 313483A Wiring Diagram / 接线图 D12 LED J9 J5 J4 J3 J1 J2 J10 ti13556a N M K J F B A E H G C D English 中文 A T o Engine 至发动机 B T o Ground 接地 C Clutch T .
Technical Data 313483A 85 T echnical Data Dimensions Honda GX 200 Engine: ANSI P ow er Rating @ 3600 rpm 6.5 Horsepower (4.8 kW) Maximum W orking Pressure: Base Coat Pump 1000 psi (69 bar , 6.9 MP a) T op Coat Pump 3300 psi (228 bar , 22.8 MP a) Noise Level: Sound P ow er 105 dBa per ISO 3744 Sound Pressure 96 dBa measured at 3.
技术数据 86 313483A 技术数据 尺寸 本田 （Honda） GX 200 发动机： ANSI 额定功率 （在 3600 rpm 时） 6.5 马力 （4.8 kW） 最大工作压力： 底色漆泵 1000 psi (69 bar, 6.
技术数据 313483A 87.
Graco Standard Warranty / Graco 公司的标准担保书 88 313483A Graco Standar d W arranty / Graco 公司的标准担保书 Graco warrants all equipment ref erenced in this document which is manufactured by Graco and bearing its name to be free from de fe c t s i n material and workmanship on the date of sale to the origin al purch aser for use.
Ein wichtiger Punkt beim Kauf des Geräts Graco Inc. 313483A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Graco Inc. 313483A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Graco Inc. 313483A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Graco Inc. 313483A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Graco Inc. 313483A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Graco Inc. 313483A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Graco Inc. 313483A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Graco Inc. 313483A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Graco Inc. 313483A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
