Benutzeranleitung / Produktwartung YUKON XL des Produzenten GM
Zur Seite of 614
2010 GMC Y ukon/Y ukon XL Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . .
2010 GMC Y ukon/Y ukon XL Owner Manual M Service and Appearance Care . . . . . . . . . . . . . . . . . . . 6-1 S e r v i c e .................................... ....... 6 - 4 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL MOTORS, GM, the GM Emblem, GMC, the GMC Truck Emblem, and the name YUKON are registered trademarks of General Motors LLC. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death.
V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
2 NOTES vi.
Section 1 In Brief Instrument Panel ................................... 1-2 Initial Drive Information .. ....... .................. 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Remote V ehicle Start . . . . . . . . . . . . . . . . .
Instrument Panel United States version shown; Canada similar 1-2.
A. Outlet Adjustment on page 4 ‑ 26 . B. T urn Signal/Multifunction Lever on page 4 ‑ 4 . C. Instrument Panel Cluster on page 4 ‑ 30 . D. Hazard Warning Flashers on page 4 ‑ 3 . E. Shift Lever . See Automatic T ransmission Operation on page 3 ‑ 33 .
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
Remote V ehicle Start With this feature the engine can be started from outside of the vehicle. Starting the V ehicle 1. Aim the RKE transmitter at the vehicle. 2. Press Q . 3. Immediately after completing Step 2, press and hold / until the turn signal lamps flash.
Liftgate Power Liftgate Use the Remote Keyless Entry (RKE) transmitter or the power door lock switches to unlock the liftgate. There are several ways to open and close the power liftgate: . Press and hold & on the RKE transmitter until the liftgate starts moving.
Windows The power window switches are located on the driver door . In addition, each passenger door has a switch for its own window . Press the switch to lower the window . Pull the switch up to raise it. For more information, see: . Windows on page 3 ‑ 19 .
Power Seats If equipped, the power seat controls are located on the outboard side of the front seats. Move the seat forward or rearward by sliding the control forward or rearward. Raise or lower the front or rear part of the cushion by moving the front or rear part of the control up or down.
Power Lumbar If equipped, this control is located on the outboard side of the seat. On vehicles with two-way lumbar , press and hold the top of the control to increase lumbar support. T o decrease, press and hold the bottom of the control. On vehicles with four-way lumbar , press and hold the front of the control to increase lumbar support.
Manual Reclining Seatbacks If equipped, this control is located on the outboard side of the seat. T o recline the seatback: 1. Lift the recline lever . 2. Move the seatback to the desired position, then release the lever to lock the seatback in place.
Memory Features This vehicle may have the memory package. The controls for this feature are located on the driver door , and are used to program and recall memory settings for the driver seat, outside mirrors, and the adjustable throttle and brake pedal feature.
Heated Seats Front Seats On vehicles with heated front seats, or heated and cooled front seats, the controls are located on the driver and passenger doors. { (If Equipped): Press to cool the entire seat. + : Press to heat the seatback only . z : Press to heat the seat and seatback.
Safety Belt Refer to the following sections for important information on how to use safety belts properly . . Safety Belts: They Are for Everyone on page 2 ‑ 32 . . How to Wear Safety Belts Properly on page 2 ‑ 37 . . Lap-Shoulder Belt on page 2 ‑ 46 .
Mirror Adjustment Exterior Mirrors V ehicles with manual outside mirrors can be adjusted so that the side of the vehicle and the area behind are seen. If the vehicle has towing mirrors, they can be adjusted for a clearer view of the objects behind you.
The mirrors may also include a memory function that works with the memory seats. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 10 for more information. Manual Foldaway Mirrors Manually fold the mirrors inward to prevent damage when going through an automatic car wash.
Interior Lighting Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
AUTO: Automatically turns on the headlamps, parking lamps, taillamps, instrument panel lights, and license plate lamps. ; : Turns on the parking lamps, taillamps, instrument panel lights, and license plate lamps. 2 : T urns on the headlamps, parking lamps, taillamps, instrument panel lights, and license plate lamps.
Climate Controls The heating, cooling, and ventilation in the vehicle can be controlled with these systems. If this vehicle is a T wo-mode Hybrid, see the T wo-mode Hybrid manual for more information. A. Fan Control B. REAR C. Air Recirculation D. Air Delivery Mode Control E.
controls, see Rear Air Conditioning and Heating System on page 4 ‑ 27 and Rear Air Conditioning and Heating System and Electronic Climate Controls on page 4 ‑ 28 . T ransmission Range Selection Mode Base trim shown (uplevel similar) The Range Selection Mode switch is located on the shift lever .
Four-Wheel Drive If the vehicle has Four-Wheel Drive, you can send the engine's driving power to all four wheels for extra traction. Automatic T ransfer Case T wo Speed T ransfer Case Single Speed T ransfer Case The transfer case knob is located next to the steering column.
V ehicle Features Radio(s) Radio with CD, DVD, and USB Port O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND: Press to choose between FM, AM, or XM ™ , if equipped. f : Select radio stations. © ¨ : Seek or scan stations.
Setting the Clock T o set the time and date for the radio with CD, DVD, and USB Port: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN, then press O , to turn the radio on. 2. Press H to display HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year).
Steering Wheel Controls For vehicles with audio steering wheel controls, some audio controls can be adjusted at the steering wheel. w / x : Press to change favorite radio stations, select tracks on a CD/DVD, or to navigate tracks or folders on an iPod ® or USB device.
Cruise Control The cruise control buttons are located on left side of the steering wheel. I : T urns the system on or off. The indicator light is on when cruise control is on and turns off when cruise control is off. + RES : Press briefly to make the vehicle resume to a previously set speed, or press and hold to accelerate.
Ultrasonic Parking Assist This feature uses sensors on the rear bumper to detect objects while parking the vehicle. URP A comes on automatically when the shift lever is moved into R (Reverse) and operates at speeds less than 8 km/h (5 mph). URP A uses audio beeps to provide distance and system information.
Sunroof There are two sunroof switches located in the overhead console above the rearview mirror . V ent: From the closed position, press the rear of the passenger side switch to vent the sunroof. Manual-Open/Manual-Close: T o open the sunroof, press and hold the rear of the driver side switch until the sunroof reaches the desired position.
Performance and Maintenance StabiliT rak ® The vehicle may have a traction control system that limits wheel spin and the StabiliT rak system that assists with directional control of the vehicle in difficult driving conditions. Both systems turn on automatically every time the vehicle is started.
The T ire Pressure Monitor can alert you about low tire pressure, but it does not replace normal monthly tire maintenance. It is the driver ’ s responsibility to maintain correct tire pressures. See Tire Pressure Monitor System on page 6 ‑ 73 and Tire Pressure Monitor Operation on page 6 ‑ 75 .
Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. . Avoid fast starts and accelerate smoothly . . Brake gradually and avoid abrupt stops. . Avoid idling the engine for long periods of time.
OnStar ® OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services. Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help.
The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy .
2 NOTES 1-32.
Section 2 Seats and Restraint System Head Restraints ............................... ..... 2-3 Front Seats ......................................... 2-4 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Power Seats .
Section 2 Seats and Restraint System Securing a Child Restraint in the Center Front Seat Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79 Securing a Child Restraint in the Right Front Seat Position . . . . . . . . . . . . .
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { W ARNING: With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
If the vehicle has a manual seat, it can be moved forward or rearward. 1. Lift the bar to unlock the seat. 2. Slide the seat to the desired position and release the bar .
Move the seat forward or rearward by sliding the control forward or rearward. Y our vehicle may have additional features to adjust your vehicle's power seat: . Raise or lower the front part of the seat cushion by moving the front of the control up or down.
Power Lumbar On seats with power lumbar , the controls used to operate this feature are located on the outboard side of the seats. This vehicle may have 2 – way lumbar . . T o increase lumbar support, press and hold the top of the control. . T o decrease lumbar support, press and hold the bottom of the control.
Heated Seats { W ARNING: If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures. T o reduce the risk of burns, people with such a condition should use care when using the seat heater , especially for long periods of time.
Heated and Cooled Seats If the front seats have the heated and cooled seat feature, the buttons used to control this feature are located on the front doors near the door handle. { (Cooled Seat): T o cool the entire seat, press the button with the cooled seat symbol.
Memory Seat, Mirrors, and Pedals Y our vehicle may have the memory package. The controls for this feature are located on the driver's door panel, and are used to program and recall memory settings for the driver's seat, outside mirrors, and the adjustable throttle and brake pedal.
T o recall the memory positions, the vehicle must be in P (Park). Press and release either button 1 or button 2 corresponding to the desired driving position. The seat, outside mirrors, and adjustable throttle and brake pedals will move to the position previously stored.
Reclining Seatbacks { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving.
{ W ARNING: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
T o return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position.
Center Seat Y our vehicle may have a front center seat. The seatback doubles as an armrest and cupholder/storage area for the driver and passenger when the center seat is not used.
Manual Fold and T umble Feature Folding and T umbling the Seat(s) T o fold and tumble the seat: 1. Make sure that there is nothing under , in front of, or on the seat. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts.
The seatback will fold forward automatically . Leaving the seatback in this position creates a flat load floor . If the seatback cannot fold flat, try moving the front seat forward and/or put the front seatback in the upright position. 3. Lift the same lever again to release the rear of the seat from the floor .
Folding and T umbling the Seat(s) from the Third Row Seats { W ARNING: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Automatic Seat Release Fold and T umble Feature The transmission must be in (P) for this feature to work. { W ARNING: Automatically folding and tumbling the seat when someone is sitting in the seat, could cause injury to the person sitting there. Always make sure there is no one sitting in the seat before pressing the automatic seat release button.
Driver's Side Rear Panel Button shown 2. Press the automatic seat release button located on the panel behind the rear doors. One press of the button automatically folds the seatback flat and tumbles the seat forward. There will be a slight delay between the folding of the seatback and the tumbling of the seat.
{ W ARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
T o return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash.
2. Lift the lever , located on the outboard side of the seat, to release the seatback. The seatback will fold forward. Leaving the seatback in this position creates a flat load floor. If the seatback cannot fold flat, try moving the front seat forward and/or put the front seatback in the upright position.
3. Lift the lever again to release the rear of the seat from the floor . The seat will tumble forward. Folding and T umbling the Seat(s) from the Third Row Seats { W ARNING: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash.
T o fold and tumble the seat from the third row seats, if your vehicle has them: 1. Make sure that there is nothing under , in front of, or on the seat. 2. Lift the lever , located on the bottom rear of the second row seat on the inboard side, to release the seatback.
Folding and T umbling the Second Row Seat(s) from the Third Row Seats or Outside { W ARNING: Using the third row seating position while the second row is folded, or folded and tumbled, could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position.
Returning the Seat(s) to the Sitting Position T o return the seat to the sitting position, do the following: 1. Pull the seat down until it latches to the floor . The seatback cannot be raised if the seat is not latched to the floor . { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash.
Returning the Seatback(s) to the Upright Position T o return the seatback to the upright position, do the following: 1. Open the liftgate to access the controls for the seat. 2. Pull up on the seatback until it locks into the upright position. { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash.
5. Lift the rear of the seat up from the floor . 6. T ilt the seat fully forward to lock it into place. 7. Push and pull on the seat to make sure it is locked.
Removing the Third Row Seat T o remove the seat, do the following: 1. Open the liftgate to access the controls for the seat. 2. Fold the seatback forward using the instructions listed under “ Folding the Seatbacks ” previously . The seat cannot be removed unless the seatback is folded.
4. Push and pull on the seat to make sure it is locked into place. The seatback cannot be raised to the upright position unless the seat is secured to the floor . 5. Pull up on the seatback until it locks into the upright position. { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly . It also describes some things not to do with safety belts. { W ARNING: Do not let anyone ride where a safety belt cannot be worn properly .
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-34.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-35.
or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces.
Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver , but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury .
Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt except for the center front passenger position, if equipped, which has a lap belt. See Lap Belt on page 2 ‑ 54 for more information. The lap ‐ shoulder belts for the first and second row seating positions are equipped with free ‐ falling latch plates.
2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across you very quickly . If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly .
3. Push the latch plate into the buckle until it clicks. If you find that the latch plate will not go fully into the buckle, see if you are using the correct buckle. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 2 ‑ 55 .
T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the safety belt is out of the way . If a door is slammed against a safety belt, damage can occur to both the belt and the vehicle.
Safety Belt Pretensioners This vehicle has safety belt pretensioners for front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly .
Third Row If your vehicle has a third row, remove the guide from its storage pocket on the side of the seat. 2. Place the guide over the belt, and insert the two edges of the belt into the slots of the guide.
3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { W ARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder . T o remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide.
Lap Belt This part is only for the lap belt. T o learn how to wear a lap-shoulder belt, see Lap-Shoulder Belt on page 2 ‑ 46 . The vehicle may have a center seating position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor .
Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender . When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you.
The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster . Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat.
{ W ARNING: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time.
{ W ARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, the child would not be restrained by the shoulder belt.
Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
{ W ARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 1 10 kg (240 lb) force on a person's arms.
{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types.
{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window .
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer .
A label on your sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever a child restraint is installed, be sure to secure the child restraint properly .
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LA TCH seating position that will accommodate a child restraint with lower attachments (B). T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether , and that the tether be attached.
For models with a three passenger third row seat, see the information following for installing a child restraint with a top tether in the third row , if your vehicle has one.
Second Row Seat — 60/40 For models with 60/40 second row seating, the top tether anchors are located at the bottom rear of the seat cushion for each seating position in the second row . Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 2 ‑ 65 for additional information.
Notice: Do not let the LA TCH attachments rub against the vehicle ’ s safety belts. This may damage these parts. If necessary , move buckled safety belts to avoid rubbing the LA TCH attachments. Do not fold the empty rear seat with a safety belt buckled.
If the position you are using does not have a headrest or head restraint and you are using a dual tether , route the tether over the seatback. If the position you are using has an adjustable headrest or head restraint and you are using a dual tether , route the tether around the headrest or head restraint.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
Use the following pictures to determine the latch plate style: Free ‐ Falling Latch Plate Cinching Latch Plate 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint.
For third row seating positions, with cinching latch plates, tilt the latch plate to adjust the belt if needed. 3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary .
4. For passenger seating positions with a lap ‐ shoulder belt and a free ‐ falling latch plate, pull the rest of the shoulder belt all the way out of the retractor to set the lock. When installing a child restraint using a lap ‐ shoulder belt and a cinching latch plate, skip Step 4 and proceed to Step 5.
6. If the child restraint has a top tether , follow the child restraint manufacturer's instructions regarding the use of the top tether . See Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 67 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor .
If the vehicle is equipped with the passenger sensing system, and when the passenger sensing system has turned off the right front passenger frontal airbag, the off indicator in the passenger airbag status indicator should light and stay lit when you start the vehicle.
Here are the most important things to know about the airbag system: { W ARNING: Y ou can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ W ARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger's side.
Driver Side Shown, Passenger Side Similar If the vehicle has seat ‐ mounted side impact airbags for the driver and right front passenger , they are in the side of the seatbacks closest to the door .
Driver Side shown, Passenger Side similar If the vehicle has a third row passenger seat, the roof-rail airbags are located in the ceiling above the rear windows for the outboard passenger positions in the third row .
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest.
In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity . The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact.
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module.
What Will Y ou See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy .
{ W ARNING: A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle.
Passenger Sensing System If the vehicle has the passenger airbag status indicator pictured in the following illustration, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator , if equipped, is visible on the overhead console when the vehicle is started.
{ W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag.
For some children, including children in child restraints, and for very small adults, the passenger sensing system may or may not turn off the right front passenger frontal airbag, depending upon the person's seating posture and body build.
5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off. Then slightly recline the vehicle seatback and adjust the seat cushion, if adjustable, to make sure that the vehicle seatback is not pushing the child restraint into the seat cushion.
If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1. T urn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your specific vehicle.
Adding Equipment to Y our Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change your vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly .
Q: What if I added a snow plow? Will it keep the airbags from working properly? A: We have designed our airbag systems to work properly under a wide range of conditions, including snow plowing with vehicles that have the optional Snow Plow Prep Package (RPO VYU).
Airbags The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 4 ‑ 32 for more information. Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly .
If the vehicle has been in a crash, do you need new safety belts or LA TCH system (if equipped) parts? After a very minor crash, nothing may be necessary . But the safety belt assemblies that were used during any crash may have been stressed or damaged.
2 NOTES 2-104.
Section 3 Features and Controls Keys ........................... ..................... 3-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . 3-4 Remote Keyless Entry (RKE) System O p e r a t i o n ................... ............... ... 3 - 5 Remote Vehicle Start .
Section 3 Features and Controls Mirrors ...... ......................... ............. 3-54 Manual Rearview Mirror . . . . . . . . . . . . . . . . . . . . . . . . 3-54 Automatic Dimming Rearview Mirror . . . . . . . . . . . 3-54 Outside Manual Mirrors .
Keys { W ARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
See your dealer if a replacement key or additional key is needed. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. If you are locked out of the vehicle, call the Roadside Assistance Center .
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter . See Remote Keyless Entry (RKE) System on page 3 ‑ 4 .
K (Unlock): Press once to unlock only the driver door . If K is pressed again within three seconds, all remaining doors unlock. The interior lamps may come on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the turn signal lamps flash twice to indicate unlocking has occurred.
Programming T ransmitters to the V ehicle Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer . When the replacement transmitter is programmed to this vehicle, all remaining transmitters must also be reprogrammed.
Remote V ehicle Start Y our vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle's heating or air conditioning systems and rear window defogger . Normal operation of the system will return after the key is turned to the ON/RUN position.
/ (Remote Start): This button will be on the RKE transmitter if you have remote start. T o start the vehicle using the remote start feature: 1. Aim the transmitter at the vehicle. 2. Press and release the transmitter's lock button. The vehicle's doors will lock.
The vehicle cannot be remote started if the key is in the ignition, the hood is not closed, or if there is an emission control system malfunction and the check engine light comes on. Also, the engine will turn off during a remote vehicle start if the coolant temperature gets too high or if the oil pressure gets low .
W ARNING: (Continued) . Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. There are several ways to lock and unlock your vehicle. From the outside, use the Remote Keyless Entry (RKE) transmitter or the key in the driver's door.
Rear Door Security Locks Y our vehicle has rear door security locks. These prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door . The rear doors must be open to access them.
Liftgate/Liftglass { W ARNING: It can be dangerous to drive with the liftglass or liftgate open because carbon monoxide (CO) gas can come into your vehicle.
On vehicles with a liftglass, press the button on the underside of the license pocket applique (A) to open it. The liftglass can also be opened by pressing the liftglass release button on the RKE. T o open the entire liftgate, press the touchpad on the underside of the liftgate handle (B).
Power Liftgate Power Liftgate Operation { W ARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
OFF: Press the bottom of the button for manual operation of the power liftgate. The taillamps will flash and a chime will sound when the power liftgate is moving. { W ARNING: Y ou or others could be injured if caught in the path of the power liftgate.
The power liftgate may be temporarily disabled under extreme temperatures, or under low battery conditions. If this occurs, the liftgate can still be operated manually . If you shift the transmission out of P (Park) while the power function is in progress, the liftgate power function will continue to completion.
Manual Operation of Power Liftgate T o change the liftgate to manual operation, press the switch on the overhead console to the OFF position. With the power liftgate disabled and all of the doors unlocked, the liftgate can be manually opened and closed.
Windows { W ARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { W ARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Express-Down/Up Windows Windows with the express feature allow the windows to be raised and lowered all the way without holding the switch. Press or pull the switch fully and release it to activate the express feature. The express mode can be canceled at any time by briefly pressing or pulling the switch.
Programming the Power Windows If the battery on the vehicle has been recharged, disconnected, or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, replace or recharge the vehicle's battery .
Theft-Deterrent Systems V ehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Y our vehicle may have a content theft-deterrent alarm system.
The theft-deterrent system will not activate if the doors are locked with the vehicle's key or the manual door lock. It activates only if you use the power door lock switch with the door open or the RKE transmitter. Y ou should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off.
P ASS-Key ® III+ Electronic Immobilizer See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada.
It is possible for the P ASS-Key ® III+ decoder to learn the transponder value of a new or replacement key . Up to 10 keys may be programmed for the vehicle.
Starting and Operating Y our V ehicle New V ehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: . Keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
Ignition Positions The ignition switch has four different positions. T o shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. A (LOCK/OFF): This position locks the ignition. It also locks the transmission on automatic transmission vehicles.
B (ACC/ACCESSOR Y): This position lets things like the radio and the windshield wipers operate while the engine is off. Use this position if the vehicle must be pushed or towed. C (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights.
Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to ST ART . When the engine starts, let go of the key . The idle speed will go down as the engine gets warm.
Adjustable Throttle and Brake Pedal On vehicles with this feature, you can change the position of the throttle and brake pedals. No adjustment to the pedals can be made when the vehicle is in R (Reverse) or while using the cruise control. The switch used to adjust the pedals is located on the instrument panel below the climate control system.
T o Use the Engine Coolant Heater 1. T urn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is secured to the Engine Compartment Fuse Block with a clip. Carefully remove the wire tie which secures the electrical cord. Do not cut the electrical cord.
Active Fuel Management ™ V ehicles with V8 engines may have Active Fuel Management ™ . This system allows the engine to operate on either all or half of its cylinders, depending on the driving conditions.
Heavy Duty 6-Speed Automatic T ransmission Shown (Light Duty Similar) See “ Range Selection Mode ” later in this section. P (Park): This position locks the rear wheels. It is the best position to use when starting the engine because the vehicle cannot move easily .
{ W ARNING: If the vehicle has a four-wheel drive transfer case with a N (Neutral) position, and the transfer case is in N (Neutral), the vehicle will be free to roll — even if the shift lever is in P (Park).
D (Drive): This position is for normal driving. It provides the best fuel economy . If you need more power for passing, and you are: . Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. . Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. Y ou can use 2 (Second) on hills. It can help control vehicle speed as you go down steep mountain roads, but then you would also want to use the brakes off and on.
T o use this feature, do the following: 1. Move the shift lever to M (Manual Mode). 2. Press the plus/minus buttons, located on the steering column shift lever , to select the desired range of gears for the current driving conditions. When M (Manual Mode) is selected a number displays next to the M, indicating the current gear .
T ow/Haul Mode The vehicle has a T ow/Haul mode. The selector button is located on the end of the column shift lever . Y ou can use this feature to assist when towing or hauling a heavy load or if there is a need to charge a battery installed in a trailer .
Grade Braking (Hydra-Matic ® 6-Speed Automatic T ransmission) The Grade Braking shift modes can be activated by pressing the button on the end of the shift control lever . While in Range Selection Mode, Grade Braking is deactivated allowing the driver to select a desired range of gears.
Four-Wheel Drive (T wo Speed Automatic T ransfer Case) If the vehicle has four-wheel drive, you can send the engine's driving power to all four wheels for extra traction.
2 m (T wo-Wheel Drive High): This setting is used for driving in most street and highway situations. The front axle is not engaged in two-wheel drive. This setting also provides the best fuel economy . AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road surface traction conditions are variable.
Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) T urn the knob to the Four-Wheel High or AUT O position. This can be done at any speed, except when shifting from Four-Wheel Drive Low . The indicator light will flash while shifting.
Shifting Out of Four-Wheel Drive Low T o shift from Four-Wheel Drive Low to Four-Wheel Drive High, AUTO, or T wo-Wheel Drive High, the vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in N (Neutral) and the ignition in ON/RUN.
Shifting into Neutral T o shift the transfer case to N (Neutral) do the following: 1. Make sure the vehicle is parked so that it will not roll. 2. Set the parking brake and apply the regular brake pedal. See Parking Brake on page 3 ‑ 48 for more information.
4. Release the parking brake prior to moving the vehicle. Notice: Shifting the transmission into gear before the Four-Wheel Drive Low indicator light has stopped flashing could damage the transfer case.
Automatic T ransfer Case The transfer case knob is located to the left of the instrument panel cluster . Use this dial to shift into and out of four-wheel drive. The vehicle has Four-Wheel-Drive with StabiliTrak ® . For information on StabiliTrak ® , see StabiliT rak ® System on page 5 ‑ 6 .
Service Four Wheel Drive If the SERVICE 4 WHEEL DRIVE message stays on, you should take the vehicle to your dealer for service. See “ SERVICE 4 WHEEL DRIVE message ” under DIC Warnings and Messages on page 4 ‑ 61 . Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) T urn the knob to the Four-Wheel High or AUT O position.
T o release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release.
Leaving the V ehicle With the Engine Running { W ARNING: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set.
Shifting Out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and .
Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Outside T owing Mirrors If the vehicle has towing mirrors, they can be adjusted for a clearer view of the objects behind you. Manually pull out the mirror head to extend it for better visibility when towing a trailer . Manually fold the mirrors forward or rearward.
Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position. Outside Power Foldaway Mirrors V ehicles with outside power foldaway mirrors have the controls located on the driver door armrest.
Outside Automatic Dimming Mirror V ehicles with this feature have a driver outside mirror that adjusts for the glare of headlamps behind you. See Automatic Dimming Rearview Mirror on page 3 ‑ 54 for more information.
Outside Heated Mirrors For vehicles with heated mirrors: < (Rear Window Defogger): Press to heat the mirrors. See “ Rear Window Defogger ” under Dual Automatic Climate Control System on page 4 ‑ 20 or Climate Control System on page 4 ‑ 18 for more information.
W ARNING: (Continued) If you do not use proper care before and while backing; vehicle damage, injury , or death could occur . Even with URP A, always check behind the vehicle before backing up. While backing, be sure to look for objects and check the vehicle's mirrors.
P ARK ASST BLOCKED SEE OWNERS MANUAL: This message can occur under the following conditions: . The ultrasonic sensors are not clean. Keep the vehicle's rear bumper free of mud, dirt, snow , ice and slush. For cleaning instructions, see Washing Y our Vehicle on page 6 ‑ 1 12 .
Before making a lane change, always check the SBZA display , check the outside and rearview mirrors, look over your shoulder for vehicles and hazards, and use the turn signal. SBZA Detection Zones The SBZA sensor covers a zone of approximately one lane over from both sides of the vehicle, 3.
SBZA displays do not come on while the vehicle is approaching or passing other vehicles. At speeds greater then 32 km/h (20 mph), SBZA displays may come on when a vehicle you have passed remains in or drops back into the detection zone. SBZA can be disabled through the Driver Information Center (DIC).
SBZA Error Messages The following messages may appear in the DIC: SIDE BLIND ZONE ALERT SYSTEM OFF: This message indicates that the driver has turned the system off.
Rear Vision Camera (RVC) This vehicle may have a Rear Vision Camera system. Read this entire section before using it. { W ARNING: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: . Detect objects that are outside the camera's field of view , below the bumper , or underneath the vehicle.
V ehicles With Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into R (Reverse), the video image automatically appears on the navigation screen.
Adjusting the Brightness and Contrast of the Screen T o adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display . Any adjustments made will only affect the rear vision camera screen.
Rear Vision Camera Location The image is provided by the camera located above the license plate. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The area displayed by the camera is limited.
When the System Does Not Seem T o Work Properly The rear vision camera system might not work properly or display a clear image if: . The RVC is turned off. See “ Turning the Rear Camera System On or Off ” earlier in this section. . It is dark. . The sun or the beam of headlights is shining directly into the camera lens.
Universal Home Remote System See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. Universal Home Remote System Operation (With Three Round LED) This vehicle may have the Universal Home Remote System.
Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
3. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
T o program up to three devices: 1. T o verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor . If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar . The switch positions on the hand-held transmitter could be labeled, as follows: . A switch in the up position could be labeled as “ Up, ” “ +, ” or “ On.
4. The indicator lights will blink slowly . Enter each switch setting from Step 2 into your vehicle's Universal Home Remote. Y ou will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: .
Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions. Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. T o erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1.
There could also be cupholders located in the second and third row seat armrest areas. Center Console Storage For vehicles with a console compartment, it is located between the bucket seats. Press the button and lift the lid to access the console compartment.
Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 5 ‑ 31 . . If small heavy objects are placed on the roof, cut a piece of 3/8 inch plywood to fit inside the crossrails and siderails to spread the load.
Cargo Cover { W ARNING: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver . Someone could be injured. If the cover is removed, always store it in the proper storage location. When it is replaced, always be sure that it is securely reattached.
Sunroof Y our vehicle may be equipped with a power sliding sunroof. T o open or close the sunroof, the ignition needs to be turned to ON/RUN, or Retained Accessory Power (RAP) must be active. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until a front door is opened.
The sunroof has a comfort stop feature which stops the sunroof from opening to the full-open position. From the comfort stop position, press the rear of the driver's side switch a second time to open the sunroof to the full-open position. When the sunroof is opened, an air deflector will automatically raise.
Section 4 Instrument Panel Instrument Panel Overview ........ ........... ..... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4 Instrument Panel T ire Pressure Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Malfunction Indicator Lamp . . . . . . . . . . . . . . . . . . . . 4-39 Oil Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Overview Hazard W arning Flashers | (Hazard W arning Flasher): Press this button located on top of the steering column, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
T urn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : T urn and Lane Change Signals 5 3 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield W asher 5 : Rear Wiper Delay Z : Rear Wiper = : Rear Wiper W ash Flash-to-Pass.
T urn Signal On Chime If the turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each flash of the turn signal and the message TURN SIGNAL ON will also appear in the Driver Information Control (DIC). T o turn the chime and message off, move the turn signal lever to the off position.
Windshield Wipers T urn the band with the wiper symbol to control the windshield wipers. 8 (Mist): Single wipe, turn to 8 , then release. Several wipes, hold the band on 8 longer . 9 (Off): Turns the windshield wipers of f. 6 (Adjustable Interval Wipes): Turn the band up for more frequent wipes or down for less frequent wipes.
Rear Window Wiper/W asher { W ARNING: In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. The rear wiper control is located on the turn signal/ multifunction lever .
If the vehicle has StabiliTrak ® , and the system begins to limit wheel spin, cruise control will automatically disengage. See StabiliT rak ® System on page 5 ‑ 6 . When road conditions allow the cruise control to be safely used again, it can be turned back on.
Increasing Speed While Using Cruise Control If the cruise control system is already activated, . Press and hold the +RES button on the steering wheel until the desired speed is reached, then release it. . T o increase vehicle speed in small amounts, press the +RES button.
Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: . Headlamps .
When the headlamps are turned on while the vehicle is on, the headlamps will turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent the battery from being drained.
Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the headlamps at the normal brightness, along with the taillamps, sidemarker , parking lamps, and the instrument panel lights. The radio lights will also be dim.
Fog Lamps For vehicles with fog lamps, the control is located next to the exterior lamps control on the instrument panel, to the left of the steering column. The ignition must be in the ON/RUN position for the fog lamps to come on. # (Fog Lamps): Press to turn the fog lamps on or off.
The emergency roof lamp circuit is fused at 30 amps, so the total current draw of the attached lamps should be less than this value. The attachment points for the roof lamp circuits are two blunt cut wires located above the overhead console, a dark green switched power wire and a black ground wire.
Entry Lighting The vehicle has an illuminated entry feature. When the doors are opened, the dome lamps will come on if the dome override button is in the extended position. If the dome override button is pressed in, the lamps will not come on. Exit Lighting The interior lamps come on when the key is removed from the ignition.
EPM works to prevent excessive discharge of the battery . It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power , whenever needed. It can temporarily reduce the power demands of some accessories.
Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown adapter or vehicle fuses. If you experience a problem, see your dealer for additional information on the accessory power plugs.
Climate Controls Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. A. Fan Control B. REAR C. Recirculation D. Air Delivery Mode Control E. Air Conditioning F . Driver and Passenger T emperature Controls G.
- (Defog): The defog mode is used to clear the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents. In this mode, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is close to freezing.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window . < (Rear Window Defogger): Press this button to turn the rear window defogger on or off. The system automatically turns off several minutes after it has been activated.
O (On/Off): Press to turn the climate control system on or off. Outside air still enters the vehicle, and is directed to the floor . This direction can be changed by pressing the mode button. Recirculation can be selected once you have selected vent or bi-level mode.
Automatic Operation AUTO (Automatic): When automatic operation is active the system will control the inside temperature, the air delivery , and the fan speed.
Manual Operation D C (Fan Control): Press these buttons to increase or decrease the fan speed. Pressing either fan button while in automatic control places the fan under manual control. The fan setting remains displayed and the AUTO light turns off. The air delivery mode remains under automatic control.
# (Air Conditioning): Press to turn the air conditioning (A/C) compressor on and of f. An indicator light comes on to show that the air conditioning is on. If this button is pressed when the air conditioning compressor is unavailable, the indicator flashes three times and then turns off.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window . < (Rear Window Defogger): Press to turn the rear window defogger on or off. It automatically turns off several minutes after it has been activated.
The interior temperature sensors located in the headliner above the driver side seat and if equipped, in the headliner above the second row seats measure the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille.
Rear Air Conditioning and Heating System For vehicles with this system, the rear controls are three knobs located in the headliner . The system can also be controlled with the front controls.
Rear Air Conditioning and Heating System and Electronic Climate Controls For vehicles with the rear heat and air conditioning controls, they are integrated with the rear seat audio controls located in the center console. The system can be controlled from the front controls as well as the rear controls.
Automatic Operation, If Equipped. AUTO: Press the air delivery mode button until this setting is selected to control the inside temperature, air delivery , and fan speed. AUTO appears in the display when automatic operation is active. +/ − (Increase/Decrease T emperature) : Press the + or − buttons to increase or decrease the cabin temperature.
Instrument Panel Cluster United States 4 ‐ Speed version shown. 6 ‐ Speed and Canada similar . For vehicles with a T wo-mode Hybrid, see the T wo-mode Hybrid manual for more information.
Speedometer and Odometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). The odometer shows how far the vehicle has been driven, in either kilometers (used in Canada) or miles (used in the United States).
Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt reminder light, several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt.
{ W ARNING: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly . The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash.
If the word ON or the on symbol is lit on the passenger airbag status indicator , it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator , it means that the passenger sensing system has turned off the right front passenger frontal airbag.
V oltmeter Gauge When the engine is not running, but the ignition is on, this gauge shows the battery's state of charge in DC volts. When the engine is running, the gauge shows the condition of the charging system. The charging system regulates voltage based on the state of the battery for improved fuel economy and battery life.
Brake System W arning Light With the ignition on, the brake system warning light comes on when the parking brake is set. If the vehicle is driven with the parking brake engaged, a chime sounds when the vehicle speed is greater than 8 km/h (5 mph). The vehicle's hydraulic brake system is divided into two parts.
If the light comes on while driving, pull off the road and stop carefully . The pedal might be harder to push or might go closer to the floor . It can take longer to stop. If the light is still on, have the vehicle towed for service. See T owing Y our Vehicle on page 5 ‑ 41 .
StabiliT rak ® Indicator Light For vehicles with the StabiliT rak ® system, this light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer . If the system is working normally the indicator light then goes off.
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated.
If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle.
Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: . Make sure the fuel cap is fully installed. See Filling the T ank on page 6 ‑ 1 1 .
Emissions Inspection and Maintenance Programs Some state/provincial and local governments may have programs to inspect the on-vehicle emission control equipment For the inspection, the emission system test equipment is connected to the vehicle ’ s Data Link Connector (DLC).
Oil Pressure Gauge United States Canada The oil pressure gauge shows the engine oil pressure in psi (pounds per square inch) when the engine is running.
Oil Pressure Light { W ARNING: Do not keep driving if the oil pressure is low . The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 4 ‑ 13 for more information. Cruise Control Light The cruise control light comes on whenever the cruise control is set.
Fuel Gauge United States Canada The fuel gauge, when the ignition is on, shows how much fuel the vehicle has left in the tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. The gauge first indicates empty before the vehicle is out of fuel, and the vehicle's fuel tank should be filled soon.
Low Fuel W arning Light This light, under the fuel gauge, comes on briefly while the engine is being started. This light and a chime comes on when the fuel tank is low on fuel. The Driver Information Center also displays a “ FUEL LEVEL LOW ” message.
DIC Operation and Displays (With DIC Buttons) If your vehicle has DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, next to the steering wheel.
T (V ehicle Information): Press this button to display the oil life, units, side blind zone system on/off, tire pressure readings for vehicles with the Tire Pressure Monitor System (TPMS), trailer bra.
Fuel Range Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling.
T ransmission T emperature Press the trip/fuel button until TRANS TEMP displays. This display shows the temperature of the automatic transmission fluid in either degrees Fahrenheit (°F) or degrees Celsius (°C).
Remember , you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.
T railer Gain and Output On vehicles with the Integrated Trailer Brake Control (ITBC) system, the trailer brake display appears in the DIC. Press the vehicle information button until TRAILER GAIN and OUTPUT display . TRAILER GAIN shows the trailer gain setting.
Compass Zone Setting This display allows for setting the compass zone. See DIC Compass on page 4 ‑ 58 Compass Recalibration This display allows for calibrating the compass. See DIC Compass on page 4 ‑ 58 Blank Display This display shows no information.
Language This display allows you to select the language in which the DIC messages will appear . T o select a language: 1. Press the trip odometer reset stem until ODOMETER displays. 2. While in the ODOMETER display , press and hold the trip odometer reset stem for three seconds until the currently set language displays.
T rip Odometer Reset Stem Menu Items Language This display allows you to select the language in which the DIC messages will appear . T o select a language: 1.
T railer Gain and Output On vehicles with the Integrated Trailer Brake Control (ITBC) system, the trailer brake display appears in the DIC. Press the trip odometer reset stem until TRAILER GAIN and OUTPUT display . TRAILER GAIN shows the trailer gain setting.
Relearn Tire Positions Y our vehicle may have this display . T o access this display , the vehicle must be in P (Park). If your vehicle has the Tire Pressure Monitor System (TPMS), after rotating the tires or after replacing a tire or sensor, the system must re-learn the tire positions.
Compass Zone The zone is set to zone eight upon leaving the factory . Y our dealer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-countr.
4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. Or , if the vehicle does not have DIC buttons, press and hold the trip odometer reset stem for two seconds to select the next available variance zone.
DIC W arnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition.
CHECK TRAILER WIRING On vehicles with the Integrated T railer Brake Control (ITBC) system, this message may display and a chime may sound when one of the following conditions exists: . A trailer with electric brakes becomes disconnected from the vehicle.
ENGINE OVERHEA TED IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur . If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 6 ‑ 36 for more information.
ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible. LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again.
REAR ACCESS OPEN This message displays and a chime sounds if the liftgate or liftglass is open while the ignition is in ON/RUN. T urn off the vehicle and check the liftgate and liftglass. Restart the vehicle and check for the message on the DIC display .
SERVICE BA TTER Y CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system. Under certain conditions, the charging system light may also turn on in the instrument panel cluster . See Charging System Light on page 4 ‑ 34 .
SERVICE ST ABILITRAK If your vehicle has StabiliTrak ® and this message displays, it means there may be a problem with the StabiliT rak system. If you see this message, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again.
SERVICE TRAILER BRAKE SYSTEM On vehicles with the Integrated T railer Brake Control (ITBC) system, this message displays and a chime sounds when there is a problem with the ITBC system. When this message displays, power is no longer available to the trailer brakes.
There are several conditions that can cause this message to appear . . One condition is overheating, which could occur if StabiliT rak activates continuously for an extended period of time. . The message also displays if the brake system warning light is on.
TIRE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires needs to be checked. This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire.
TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty .
DIC V ehicle Customization (With DIC Buttons) Y our vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
DISPLA Y LANGUAGE This feature allows you to select the language in which the DIC messages will appear . Press the customization button until the DISPLA Y LANGUAGE screen appears on the DIC display . Press the set/reset button once to access the settings for this feature.
AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 3 ‑ 1 1 for more information.
T o select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter .
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF . Press the customization button until EXIT LIGHTING appears on the DIC display .
CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display .
EASY EXIT RECALL If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 10 for more information. Press the customization button until EASY EXIT RECALL appears on the DIC display .
MEMOR Y SEA T RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 10 for more information. Press the customization button until MEMORY SEA T RECALL appears on the DIC display .
F ACTOR Y SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until F ACTORY SETTINGS appears on the DIC display . Press the set/reset button once to access the settings for this feature.
T o minimize taking your eyes off the road while driving, do the following while the vehicle is parked: . Become familiar with the operation and controls of the audio system. . Set up the tone, speaker adjustments, and preset radio stations. For more information, see Defensive Driving on page 5 ‑ 2 .
5. T o decrease the time or date, do one of the following: . Press the © SEEK button. . Press the s REV button. . T urn the f knob counterclockwise. T o change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1.
Radio with CD/MP3/DVD and USB The vehicle has one of these radios as its audio system. Radios with CD and DVD Radios with CD/MP3/DVD and USB have a Bose ® Surround Sound System. Some of its features are explained later in this section under , “ Adjusting the Speakers (Balance/Fade) ” .
Playing the Radio O (Power/V olume): Press to turn the system on and off. T urn clockwise or counterclockwise to increase or decrease the volume. Speed Compensated V olume (SCV): Radios with Speed Compensated V olume (SCV) automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down.
Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is stopped. T une to favorite stations using the softkeys, favorites button, and steering wheel controls, if the vehicle has this feature.
Setting the T one (Bass/Midrange/T reble) BASS/MID/TREB (Bass, Midrange, or T reble): T o adjust bass, midrange, or treble, press the f knob until the tone control tabs display . Continue pressing to highlight the desired tab, or press the softkey below the tab.
Finding a Category (CA T) Station CA T (Category): The CA T button is used to find XM stations when the radio is in the XM mode. T o find XM channels within a category: 1. Press the BAND button until the XM frequency displays. Press the CA T button to display the category tabs.
Radio Messages Calibration Error: The audio system has been calibrated for the vehicle from the factory . If Calibration Error displays, it means that the radio has not been configured properly for the vehicle and it must be returned to your dealer for service.
Care of CDs and DVDs If playing a CD-R, the sound quality can be reduced due to CD-R or CD-RW quality , the method of recording, the quality of the music that has been recorded, and the way the CD-R or CD-RW has been handled.
Ejecting a Disc Z EJECT or CD (Eject): Press and release to eject the disc that is currently playing. A CD ejecting from a radio with CD/MP3/DVD and USB, ejects from the bottom slot. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays.
FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound is heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. RDM (Random): With the random setting, the tracks can be listened to in random, rather than sequential order .
Radios with CD and DVD Audio Output Only one audio source can be heard through the speakers at a time. An audio source is defined as DVD slot, CD slot, XM, FM/AM, Front Auxiliary Jack, or Rear Auxiliary Jack. Press the O button to turn the radio on. The radio can be heard through all of the vehicle speakers.
Player Error: There are disc LOAD or disc EJECT problems. . It is very hot. When the temperature returns to normal, the CD should play . . The road is very rough. When the road becomes smoother , the CD should play . . The CD is dirty , scratched, wet, or upside down.
Inserting a Disc T o play a disc, gently insert the disc, with the label side up, into the loading slot. The DVD player might not accept some paper labeled media. The player starts loading the disc into the system and shows “ Loading Disc ” on the radio display .
A lock symbol displays next to the clock display . The parental control feature remains on until this knob is pressed and held for more than two seconds again, or until the driver turns the ignition off and exits the vehicle. f (T une): Turn to change tracks on a CD or DVD.
Some DVDs begin playing after the previews have finished, although there could be a delay of up to 30 seconds. If the DVD does not begin playing the movie automatically , press the softkey under the play/pause tab on the radio. If the DVD still does not play , refer to the on-screen instructions, if available.
Stopping and Resuming Playback T o stop playing a DVD without turning off the system, press the c button on the remote control, or press the softkey under the stop or the play/pause tab displayed on the radio. If the radio head is sourced to something other than DVD-V , press the DVD/CD AUX button to make DVD-V the active source.
Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. An external audio device such as an iPod, laptop computer , MP3 player , CD player , or cassette tape player , etc.
Using the USB Port Radios with a USB port can control a USB storage device or an iPod ® using the radio buttons and knobs. See Using an MP3 (Radios with CD) on page 4 ‑ 99 or Using an MP3 (Radios with CD and DVD) on page 4 ‑ 106 for information about how to connect and control a USB storage device or an iPod.
CD ‐ R or CD ‐ RW Supported File and Folder Structure The radio supports: . Up to 50 folders. . Up to 8 folders in depth. . Up to 50 playlists. . Up to 255 files. . Playlists with an .m3u or .wpl extension. . Files with an .mp3, .wma, or .cda file extension.
File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the extension (such as .mp3) as the track name. T rack names longer than 32 characters or four pages are shortened.
FWD (Fast Forward): Press and hold to advance playback quickly . Sound is heard at a reduced volume and the elapsed time of the file displays. Release FWD to resume playing. The elapsed time of the file displays. S c (Previous Folder): Press the softkey below S c to go to the first track in the previous folder.
Connecting a USB Storage Device or iPod ® The USB Port can be used to control an iPod or a USB storage device. T o connect a USB storage device, connect the device to the USB port located on the instrument panel or in the center console.
Using Softkeys to Control a USB Storage Device or iPod The five softkeys below the radio display are used to control the functions listed below . T o use the softkeys: 1. Press the first or fifth softkey below the radio display to display the functions listed below , or press the softkey below the function if it is currently displayed.
h (Music Navigator): Press the softkey below h to view and select a file on an iPod, using the iPod's menu system. Files are sorted by: . Playlists . Artists . Albums . Genres . Songs . Composers T o select files: 1. Press the softkey below h . 2.
Shuffle Functionality T o use Shuffle: Press the softkey below > , 2 , < or = to select between Shuffle Off, Shuffle All Songs/Shuffle Songs, Shuffle Album, or Shuffle Folder . > (Shuffle Off): Press the softkey below 2 to turn shuffle off. This is the default mode when a USB storage device or iPod is first connected.
CD ‐ R or CD ‐ RW Supported File and Folder Structure The DVD Player supports: . Up to 255 folders. . Up to 8 folders in depth. . Up to 15 playlists. . Up to 40 sessions. . Playlists with an .m3u or .wpl extension. . Files with an .mp3, .wma, or .
Empty Folder Folders that do not contain files are skipped, and the player advances to the next folder that contains files. No Folder When the disc contains only compressed files, the files are located under the root folder . The next and previous folder function does not function on a disc that was recorded without folders or playlists.
Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp ™ , MusicMatch ™ , or Real Jukebox ™ software can be accessed, however , they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song files.
When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display . Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist.
Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio ’ s display . f (T une): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played.
3. Press f to select the folder . If there is more than one folder , repeat Steps 1 and 2 until the folder is reached. 4. T urn f to scroll through the files in the selected folder . 5. Press f to select the file to be played. T o skip through large lists, the five softkeys can be used to navigate in the following order: .
Repeat Functionality T o use Repeat: Press the softkey below " or ' to select between Repeat All and Repeat T rack. " (Repeat All): Press the softkey below " to repeat all tracks. The tab appears lowered when Repeat All is being used.
No Title Info: No song title information is available at this time on this channel. The system is working properly . No CA T Info: No category information is available at this time on this channel. The system is working properly . No Information: No text or informational messages are available at this time on this channel.
V oice Recognition The Bluetooth system uses voice recognition to interpret voice commands to dial phone numbers and name tags. Noise: Keep interior noise levels to a minimum. The system may not recognize voice commands if there is too much background noise.
Pairing Information: . Up to five cell phones can be paired to the in ‐ vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in ‐ vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ List ” .
Using the Store Command The store command allows a phone number to be stored without entering the digits individually . 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Store ” . The system responds with “ Store, number please ” followed by a tone.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number .
3. Say the name tag to be deleted. The system responds with “ Would you like to delete, <name tag>? Please say yes or no ” . . If the name tag is correct, say “ Y es ” to delete the name tag. The system responds with “ OK, deleting <name tag>, returning to the main menu.
Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Digit Dial ” . The system responds with “ Digit dial using <phone name>, please say the first digit to dial ” followed by a tone.
Using the Re ‐ dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Re ‐ dial ” . The system responds with “ Re ‐ dial using <phone name> ” and dials the last number called from the connected Bluetooth phone.
Three ‐ W ay Calling Three ‐ W ay Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Three ‐ way call ” .
T o T ransfer Audio to the In-V ehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the key is turned to the ON/RUN or ACC/ ACCESSORY position.
Sending a Stored Name T ag During a Call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Send name tag. ” The system responds with “ Say a name tag to send tones ” followed by a tone. 3. Say the name tag to send.
Before Driving The RSE is designed for rear seat passengers only . The driver cannot safely view the video screen while driving and should not try to do so. In severe or extreme weather conditions the RSE system might not work until the temperature is within the operating range.
Infrared transmitters are located at the rear of the RSE overhead console. The headphones shut off automatically to save the battery power if the RSE system and RSA are shut off or if the headphones are out of range of the transmitters for more than three minutes.
Audio/Video (A/V) Jacks The A/V jacks, located on the rear of the floor console, allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Adapter connectors or cables (not included) might be required to connect the auxiliary device to the A/V jacks.
Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following possible sources: . Wireless Headphones . V ehicle Speakers .
Remote Control T o use the remote control, aim it at the transmitter window at the rear of the overhead console and press the desired button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control.
z (Display Menu): Press this button to adjust the brightness, screen display mode (normal, full, or zoom), and display the language menu. q (Return): Press this button to exit the current active menu and return to the previous menu. This button operates only when the display menu or a DVD menu is active.
d (Camera): Press this button to change camera angles on DVDs that have this feature when a DVD is playing. The format and content of this function vary for each disc. 1 through 0 (Numeric Keypad): The numeric keypad provides the capability of direct chapter or track number selection.
Tips and T roubleshoo ting Chart (cont'd) Problem Recommended Action After stopping the player , I push Play but sometimes the DVD starts where I left off and sometimes at the beginning. If the stop button was pressed one time, the DVD player resumes playing where the DVD was stopped.
DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle.
Audio can be heard through wired headphones (not included) plugged into the jacks on the RSA. If the vehicle has this feature, audio can also be heard on Channel 2 of the wireless headphones. The audio system mutes the rear speakers when the RSA audio is active through the headphones.
PROG (Program): Press this button to go to the next preset radio station or channel set on the main radio. This function is inactive, with some radios, if the front seat passengers are listening to the radio. When a CD or DVD audio disc is playing, press this button to go to the beginning of the CD or DVD audio.
CD/DVD T o select tracks on a CD/DVD: Press and release w or x to go to the next or previous track. Select tracks on an iPod or USB Device (V ehicles without a Navigation System) 1. Press and hold w or x while listening to a song until the contents of the current folder display on the radio display .
Navigating an iPod or USB Device on the Music Navigator Screen (V ehicles with a Navigation System) Press and release w or x to select the next or previous track within the selected category . Press and hold w or x to move quickly through the tracks within the selected category .
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Rear Side Window Antenna The AM-FM antenna is located in the passenger rear side windows. Make sure the inside surfaces of the rear side windows are not scratched and that the lines on the glass are not damaged. If the inside surfaces are damaged, they could interfere with radio reception.
Section 5 Driving Y our V ehicle Y our Driving, the Road, and the V ehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ................................. .. 5 - 2 Control of a V ehicle .
Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 32 .
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
Avoid needless heavy braking. Some people drive in spurts, heavy acceleration followed by heavy braking, rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking.
Let us say the road is wet and you are driving safely . Suddenly , an animal jumps out in front of you. Y ou slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that the wheels are slowing down.
StabiliT rak ® System The vehicle has a vehicle stability enhancement system called StabiliT rak. It is an advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions.
The StabiliT rak light will flash on the instrument panel cluster when the system is both on and activated. The system may be heard or felt while it is working; this is normal. The traction control disable button is located on the instrument panel below the climate controls.
T raction Control Operation The traction control system is part of the StabiliTrak system. T raction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary .
Steering Power Steering If the vehicle is a T wo ‐ mode Hybrid, see the Two ‐ mode Hybrid manual for more information. If power steering assist is lost because the engine stops or the system is not functioning, the vehicle can be steered but it will take more effort.
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly , and just as quickly straighten the wheel once you have avoided the object.
Passing Passing another vehicle on a two-lane road can be dangerous. T o reduce the risk of danger while passing: . Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. . W atch for traffic signs, pavement markings, and lines that could indicate a turn or an intersection.
Of course, traction is reduced when water , snow, ice, gravel, or other material is on the road. For safety , slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Before Y ou Go Off-Roading . Have all necessary maintenance and service work done. . Make sure there is enough fuel, that fluid levels are where they should be, and that the spare tire, if the vehicle has one, is fully inflated. . Be sure to read all the information about four-wheel-drive vehicles in this manual.
Loading Y our V ehicle for Off-Road Driving { W ARNING: . Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. Y ou or your passengers could be injured. Keep cargo below the top of the seatbacks. . Unsecured cargo on the load floor can be tossed about when driving over rough terrain.
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However , it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: .
Controlling the vehicle is the key to successful off-r oad driving. One of the best ways to control the vehicle is to control the speed. At higher speeds: . Y ou approach things faster and have less time to react. . There is less time to scan the terrain for obstacles.
When driving over bumps, rocks, or other obstacles, the wheels can leave the ground. If this happens, even with one or two wheels, you cannot control the vehicle as well or at all. Because you will be on an unpaved surface, it is especially important to avoid sudden acceleration, sudden turns, or sudden braking.
Driving Uphill Once you decide it is safe to drive up the hill: . Use a low gear and get a firm grip on the steering wheel. . Get a smooth start up the hill and try to maintain speed. Not using more power than needed can avoid spinning the wheels or sliding.
. If the engine has stopped running, you need to restart it. With the brake pedal pressed and the parking brake still applied, shift the transmission to P (Park) and restart the engine. Then, shift to R (Reverse), release the parking brake, and slowly back down the hill as straight as possible in R (Reverse).
Driving Downhill When off-roading takes you downhill, consider: . How steep is the downhill? Will I be able to maintain vehicle control? . What is the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? . Are there hidden surface obstacles? Ruts? Logs? Boulders? .
Driving Across an Incline An off-road trail will probably go across the incline of a hill. T o decide whether to try to drive across the incline, consider the following: { W ARNING: Driving across an incline that is too steep will make your vehicle roll over .
Stalling on an Incline { W ARNING: Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over , you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path.
Driving in W ater { W ARNING: Driving through rushing water can be dangerous. Deep water can sweep your vehicle downstream and you and your passengers could drown. If it is only shallow water , it can still wash away the ground from under your tires, and you could lose traction and roll the vehicle over .
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: . Drive defensively . . Do not drink and drive.
Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle's tires so they actually ride on the water . This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy , find a safe place to park your vehicle and rest. Other driving tips include: . Keep the vehicle well ventilated. . Keep interior temperature cool.
{ W ARNING: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill.
Allow greater following distance on any slippery road and watch for slippery spots. Icy patches can occur on otherwise clear roads in shaded areas. The surface of a curve or an overpass can remain icy when the surrounding roads are clear . Avoid sudden steering maneuvers and braking while on ice.
W ARNING: (Continued) Y ou cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust. Run the engine for short periods only as needed to keep warm, but be careful.
Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the area around the front wheels. For four-wheel-drive vehicles, shift into Four ‐ Wheel High or , if the vehicle has a two ‐ speed automatic transfer case, Four ‐ Wheel Low .
Notice: Never use recovery hooks to tow the vehicle. Y our vehicle could be damaged and it would not be covered by warranty . For vehicles with recovery hooks at the front of the vehicle, you can use them if you are stuck off-road and need to be pulled to some place where you can continue driving.
Tire and Loading Information Label Label Example A vehicle specific T ire and Loading Information label is attached to the center pillar (B-pillar). With the driver's door open, you will find the label attached below the door lock post (striker).
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if the “ XXX ” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs).
Example 2 Item Description T otal A V ehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 5 = 750 lbs (136 kg) C Available Cargo Weight = 250 lbs .
Refer to your vehicle's tire and loading information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver , passengers, and cargo should never exceed your vehicle's capacity weight.
And, if you do have a heavy load, you should spread it out. { CAUTION: Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GA WR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles.
There is also important loading information for off-road driving in this manual. See “ Loading Y our V ehicle for Off-Road Driving ” under Off-Road Driving on page 5 ‑ 12 .
Here are some guidelines for safely carrying a snow plow on your vehicle: . Make sure the weight on the front and rear axles does not exceed the axle rating for each. . For the front axle, if more cargo or passengers must be carried, appropriate counter ballast must be installed rear of the rear axle.
In order to calculate the amount of weight any front accessory , such as a snow plow , is adding to the front axle, use the following formula: (W x (A + W .B.)) /W .B.= Weight the accessory is adding to the front axle. Where: W = Weight of added accessory A = Distance that the accessory is in front of the front axle W .
Y ou can add heavier equipment on the front of the vehicle if you compensate for it by carrying fewer passengers, less cargo, or by positioning cargo towards the rear . This has the effect of reducing the load on the front. However , the front GAWR, rear GA WR, and the Gross V ehicle Weight Rating (GVWR) must never be exceeded.
T owing T owing Y our V ehicle T o avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 8 ‑ 7 .
Dinghy T owing T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty .
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dinghy tow a four-wheel drive vehicle with a two speed automatic transfer case: 1. Position the vehicle being towed behind the tow vehicle and shift the transmission to P (Park).
Dolly T owing Front T owing (Front Wheels Off the Ground) T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Notice: If a two-wheel drive vehicle or.
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dolly tow a four-wheel drive vehicle from the front: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the front wheels onto the dolly .
Rear T owing (Rear Wheels Off the Ground) T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Use the following procedure to dolly tow the vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions.
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dolly tow a four-wheel drive vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the rear wheels onto the dolly .
Level Control Automatic Level Control The automatic level control rear suspension is available on light ‐ duty vehicles and comes as a part of the Autoride ® suspension, if equipped.
T owing a T railer If the vehicle has a two – mode hybrid engine, see the T wo – mode Hybrid manual for more information. Do not tow a trailer during break ‐ in.
Pulling A T railer Here are some important points: . There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
V ehicle Axle Ratio Maximum T railer Weight GCWR* 1500 Series 2WD Short Wheel Base 5.3L V8 3.08 5,400 lbs (2 449 kg) 1 1,000 lbs (4 990 kg) 5.3L V8 3.42 5,900 lbs (2 676 kg) 1 1,500 lbs (5 216 kg) 5.3L V8 K5L HD Cooling Pkg 3.42 8,400 lbs (3 810 kg) 14,000 lbs (6 350 kg) 1500 Series 2WD Long Wheel Base 5.
V ehicle Axle Ratio Maximum T railer Weight GCWR* 1500 Series 4WD Long Wheel Base 5.3L V8 3.08 5,000 lbs (2 268 kg) 1 1,000 lbs (4 990 kg) 5.3L V8 3.42 5,400 lbs (2 449 kg) 1 1,500 lbs (5 216 kg) 5.3L V8 K5L HD Cooling Pkg 3.42 7,900 lbs (3 583 kg) 14,000 lbs (6 350 kg) 6.
Weight of the T railer T ongue The tongue load (A) of any trailer is very important because it is also part of the vehicle weight. The Gross V ehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle as well as trailer tongue weight.
Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle. T railering may be limited by the vehicle's ability to carry tongue weight.
Weight ‐ Distributing Hitch Adjustment A: Body to Ground Distance B: Front of V ehicle When using a weight-distributing hitch, the spring bars should be adjusted so the distance (A) is the same after coupling the trailer to the tow vehicle and adjusting the hitch.
T ow/Haul Mode Pressing this button at the end of the shift lever turns on and off the tow/haul mode. This indicator light on the instrument panel cluster comes on when the tow/haul mode is on. T ow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load.
T railer Brakes A loaded trailer that weighs more than 2,000 lbs (900 kg) needs to have its own brake system that is adequate for the weight of the trailer . Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly .
The ITBC system is powered through the vehicle's electrical system. T urning the ignition off will also turn off the ITBC system. The ITBC system is fully functional only when the ignition is in ON or in RUN. The ITBC system can only be used with trailers with electric brakes.
T railer Brake Control Panel A. Manual T railer Brake Apply Lever B. T railer Gain Adjustment Buttons The ITBC system has a control panel located on the instrument panel to the left of the steering column.
All DIC warning and service messages must first be acknowledged by the driver by pressing the odometer trip stem or the DIC V ehicle Information button (if equipped) before the Trailer Brake Display Page can be displayed and T railer Gain can be adjusted.
Manual T railer Brake Apply The Manual T railer Brake Apply Lever is located on the T railer Brake Control Panel and is used to apply the trailer ’ s electric brakes independent of the vehicle ’ s brakes. This lever is used in the Trailer Gain Adjustment Procedure to properly adjust the power output to the trailer brakes.
5. Drive the vehicle with the trailer attached on a level road surface representative of the towing condition and free of traffic at about 20 to 25 mph (32 to 40 km/h) and fully apply the Manual T railer Brake Apply lever . Adjusting trailer gain at speeds lower than 20 to 25 mph (32 to 40 km/h) may result in an incorrect gain setting.
2. There is an electrical fault in the wiring to the electric trailer brakes. This message will continue as long as there is an electrical fault in the trailer wiring.
Driving with a T railer { W ARNING: When towing a trailer , exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled.
Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. T o move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you.
Parking on Hills { W ARNING: Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
Leaving After Parking on a Hill 1. Apply and hold the brake pedal. 2. Start the engine 3. Shift into a gear 4. Release the parking brake 5. Let up on the brake pedal. 6. Drive slowly until the trailer is clear of the chocks. 7. Stop and have someone pick up and store the chocks.
Heavy-Duty T railer Wiring Harness Package The vehicle is equipped with the seven-wire trailer towing harness. This harness with a seven-pin universal trailer connector is attached to a bracket on the hitch platform. The seven-wire harness contains the following trailer circuits: .
Electric Brake Control Wiring Provisions These wiring provisions are included with the vehicle as part of the trailer wiring package. These provisions are for an electric brake controller . The instrument panel contains blunt cut wires near the data link connector for the trailer brake controller .
2 NOTES 5-70.
Section 6 Service and Appearance Care Service ......... ........................... ......... 6-4 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-4 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-5 California Perchlorate Materials R e q u i r e m e n t s .
Section 6 Service and Appearance Care Tires ............................ ................... 6-63 T ire Sidewall Labeling . . . . . . . . . . . . . . . . . . . . . . . . . 6-64 T ire T erminology and Definitions . . . . . . . . . . . . . . . 6-69 Inflation - T ire Pressure .
Section 6 Service and Appearance Care V ehicle Identification ............................ 6-1 17 V ehicle Identification Number (VIN) . . . . . . . . . . . 6-1 17 Service Parts Identification Label . . . . . . . . . . . . . 6-1 17 Electrical System .
Service For service and parts needs, visit your dealer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modif.
California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Y our Airbag-Equipped V ehicle on page 2 ‑ 99 . Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 15 .
V ehicles that have a FlexFuel badge and a yellow fuel cap can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Fuel E85 (85% Ethanol) on page 6 ‑ 9 . For all other vehicles, use only the unleaded gasoline described under Gasoline Octane on page 6 ‑ 7 .
California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications.
Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT . We recommend against the use of such gasolines.
T o ensure quick starts in the wintertime, the E85 fuel must be formulated properly for your climate according to ASTM specification D 5798. If you have trouble starting on E85, it could be because the E85 fuel is not properly formulated for your climate.
Filling the T ank { W ARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle.
T o open the fuel door , push the rearward center edge in and release and it will open. T o remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door .
When replacing the fuel cap, insert the tether in its hole before tightening the cap. T urn the fuel cap clockwise until it clicks. It will require more effort to turn the fuel cap on the last turn as you tighten it. Make sure the cap is fully installed.
Checking Things Under the Hood { W ARNING: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Things that burn can get on hot engine parts and start a fire.
2. Then go to the front of the vehicle and locate the secondary hood release, near the center of the grille. 3. Push the secondary hood release to the right.
Engine Compartment Overview If the vehicle is a T wo-mode Hybrid, see the T wo-mode Hybrid manual for more information. When you open the hood on the 5.
A. Engine Air Cleaner/Filter on page 6 ‑ 22 . B. Coolant Surge T ank and Pressure Cap. See Cooling System on page 6 ‑ 30 . C. Remote Positive (+) T erminal. See Jump Starting on page 6 ‑ 46 . D. Battery on page 6 ‑ 45 . E. Engine Oil Fill Cap.
Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 6 ‑ 16 for the location of the engine oil dipstick.
See Engine Compartment Overview on page 6 ‑ 16 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through. What Kind of Engine Oil to Use Look for three things: .
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty .
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required.
What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer . Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water , or a good hand cleaner .
3. Remove the engine air cleaner/filter from the housing. Care should be taken to dislodge as little dirt as possible. 4. Clean the engine air cleaner/filter sealing surfaces and the housing. 5. Inspect or replace the engine air cleaner/filter . 6. Reinstall the cover and tighten the screws.
Automatic T ransmission Fluid (4-Speed T ransmission) When to Check and Change Automatic T ransmission Fluid A good time to check the automatic transmission fluid level is when the engine oil is changed.
Checking the Fluid Level Prepare the vehicle as follows: 1. Park the vehicle on a level place. Keep the engine running. 2. With the parking brake applied, place the shift lever in P (Park). 3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
4. Check both sides of the dipstick, and read the lower level. The fluid level must be in the COLD area, below the cross-hatched area, for a cold check or in the HOT or cross-hatched area for a hot check. Be sure to keep the dipstick pointed down to get an accurate reading.
Automatic T ransmission Fluid (6-Speed T ransmission) When to Check and Change Automatic T ransmission Fluid It is usually not necessary to check the transmission fluid level. The only reason for fluid loss is a transmission leak or overheating the transmission.
4. Allow the engine to idle (500 – 800 rpm) for at least one minute. Slowly release the brake pedal. 5. Keep the engine running and press the T rip/Fuel button or trip odometer reset stem until TRANS TEMP (T ransmission T emperature) displays on the Driver Information Center (DIC).
5. If the fluid level is below the COLD check band, add only enough fluid as necessary to bring the level into the COLD band. It does not take much fluid, generally less than 0.
5. Safe operating level is within the HOT cross hatch band on the dipstick. If the fluid level is not within the HOT band, and the transmission temperature is between 71°C and 93°C (160°F and 200°F), add or drain fluid as necessary to bring the level into the HOT band.
5.3L Engine shown, 6.0L and 6.2L Engine similar A. Coolant Surge T ank B. Coolant Surge T ank Pressure Cap C. Engine Cooling Fan(s) { W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury .
Engine Coolant The cooling system in the vehicle is filled with DEX-COOL ® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low .
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down.
How to Add Coolant to the Surge T ank { W ARNING: Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
If no coolant is visible in the surge tank, add coolant as follows: 1. Y ou can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. T urn the pressure cap slowly counterclockwise about one full turn.
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. W atch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower .
Y ou may decide not to lift the hood when this warning appears, but instead get service help right away . See Roadside Assistance Program on page 8 ‑ 7 . If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running.
If No Steam Is Coming From The Engine Compartment The ENGINE OVERHEA TED STOP ENGINE or the ENGINE OVERHEA TED IDLE ENGINE message, along with a low coolant condition, can indicate a serious problem. If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious.
Overheated Engine Protection Operating Mode If an overheated engine condition exists and the ENGINE POWER IS REDUCED message is displayed, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage. In this mode, you will notice a loss in power and engine performance.
Power Steering Fluid If the vehicle is a T wo-mode Hybrid, see the Two-mode Hybrid manual for more information. See Engine Compartment Overview on page 6 ‑ 16 for reservoir location.
Windshield W asher Fluid What to Use When windshield washer fluid needs to be added, be sure to read the manufacturer's instructions before use. Use a fluid that has sufficient protection against freezing in an area where the temperature may fall below freezing.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6 ‑ 16 for the location of the reservoir . There are only two reasons why the brake fluid level in the reservoir might go down: .
Checking Brake Fluid Check brake fluid by looking at the brake fluid reservoir . See Engine Compartment Overview on page 6 ‑ 16 . The fluid level should be above MIN.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly .
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking.
Jump Starting If the vehicle is a T wo-mode Hybrid, see the Two-mode Hybrid manual for more information. If the vehicle's battery (or batteries) has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely .
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty . Always turn off the radio and other accessories when jump starting the vehicle. 3. T urn off the ignition on both vehicles.
{ W ARNING: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. { W ARNING: Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know . Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal.
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. All axle assemblies are filled by volume of fluid during production.
2500 Series T o get an accurate reading, the vehicle should be on a level surface. . For all 4.8L, 5.3L 1500 series and all 6.2L all wheel drive 1500 series luxury model applications , the proper level is from 0.04 inch to 0.75 inch (1.0 mm to 19.0 mm) below the bottom of the filler plug hole, located on the rear axle.
How to Check Lubricant Active T ransfer Case A. Fill Plug B. Drain Plug T o get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the fill plug hole, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the fill plug hole.
How to Check Lubricant T o get an accurate reading, the vehicle should be on a level surface. 1500 Series A: Fill Plug B: Drain Plug All except 1500 Series A: Fill Plug B: Drain Plug . When the differential is cold, add enough lubricant to raise the level from 0 (0 mm) to 1/8 inch (3.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 . Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps have been preset at the factory and should need no further adjustment.
T o adjust the vertical aim: 1. Open the hood. See Hood Release on page 6 ‑ 14 2. Locate the aim dot on the lens of the low ‐ beam headlamp. 3. Record the distance from the ground to the aim dot on the low ‐ beam headlamp. 4. At a wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it.
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly . The adjustment screw can be turned with an E8 T orx ® socket. 8. T urn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 ‑ 60 . For any bulb changing procedure not listed in this section, contact your dealer . Halogen Bulbs { W ARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
T o replace one of these bulbs: 1. Open the liftgate. See Power Liftgate on page 3 ‑ 15 . 2. Remove the two screws from the taillamp assembly . 3. Pull the taillamp assembly rearward until you disengage the inner pins on the taillamp assembly from the vehicle.
License Plate Lamp 1. Remove the two screws holding each of the license plate lamps to the molding that is part of the liftgate. 2. T wist and pull the license plate lamp forward through the molding opening. 3. T urn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 7 ‑ 3 . Replacement blades come in different types and are removed in different ways. T o replace the wiper blade assembly: 1.
Backglass Wiper Blade Replacement 1. Lift the wiper blade assembly up and out of the park rest position. 2. Pull the wiper blade assembly away from the backglass. The backglass wiper blade will not lock in a vertical position, so care should be used when pulling it away from the vehicle.
Tires Y our new vehicle comes with high-quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. For additional information refer to the tire manufacturer .
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P ‐ Metric and a L T ‐ Metric tire sidewall.
(E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear , traction, and temperature resistance.
(B) TPC Spec (Tire Performanc e Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Tire Size The following examples show the different parts of a tire size. Passenger (P ‐ Metric) Tire (A) Passenger (P ‐ Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Light T ruck (L T ‐ Metric) Tire (A) Light T ruck (L T ‐ Metric) Tire : The United States version of a metric tire sizing system. The letters L T as the first two characters in the tire size means a light truck tire engineered to standards set by the U.
Tire T erminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light T ruck (L T ‐ Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles.
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Inflation - Tire Pressure If your vehicle is a T wo ‐ mode Hybrid, see the T wo ‐ mode Hybrid manual for more information. T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under ‐ inflation or over ‐ inflation is all right.
How to Check Use a good quality pocket-type gauge to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are underinflated. Check the tire's inflation pressure when the tires are cold.
Accordingly , when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under ‐ inflated tire causes the tire to overheat and can lead to tire failure.
Tire Pressure Monitor Operation If your vehicle is a Two ‐ mode Hybrid, see the T wo ‐ mode Hybrid manual for more information. This vehicle may have a T ire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position.
8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 6 ‑ 75 . Make certain that all wheel nuts are properly tightened.
Y ou need new tires if any of the following statements are true: . Y ou can see the indicators at three or more places around the tire. . Y ou can see cord or fabric showing through the tire's rubber . . The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four . This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new . Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability , and resistance to rollover .
While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors T ire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition T o These Grades.
T emperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air , replace it (except some aluminum wheels, which can sometimes be repaired).
Used Replacement Wheels { W ARNING: Putting a used wheel on the vehicle is dangerous. Y ou cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Notice: If your vehicle has P265/70R17 size tires, use tire chains only where legal and only when you must. Use chains that are the proper size for your vehicle's tires. Install them on the rear tires only . Do not use chains on the front tires. Tighten them as tightly as possible with the ends securely fastened.
Changing a Flat Tire If your vehicle is a Two-mode Hybrid, see the T wo-mode Hybrid manual for more information. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 4 ‑ 3 .
A. Wheel Block B. Flat T ire The following information explains how to use the jack and change a tire. Removing the Spare Tire and T ools The equipment you will need to change a flat tire is stored under the storage tray , which is located on the driver side trim panel (over the rear wheelhouse).
2. Remove the wing nut (B) used to retain the tool bag by turning it counterclockwise. 3. T urn the knob (A) on the jack counterclockwise to release the jack and wheel blocks from the bracket. 4. Remove the wheel blocks and the wheel block retainer by turning the wing nut (C) counterclockwise.
T o access the spare tire, refer to the following graphics and instructions: A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access Cover/Hole D. Jack Handle Extensions E. Wheel Wrench F . Hoist Cable G. T ire/Wheel Retainer H. Spare T ire (V alve Stem Pointed Down) I.
4. Insert the open end of the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole). Be sure the hoist end (J) of the extension (D) connects to the hoist shaft (B). The ribbed square end of the extension is used to lower the spare tire.
7. T ilt the tire toward the vehicle with some slack in the cable to access the tire/wheel retainer . Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch.
Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 88 for more information. 2. If your vehicle has a center cap that covers the wheel fasteners, place the chisel end of the wheel wrench in the slot on the wheel and gently pry the cap out.
Jacking Locations (Overall View) A. Front Position B. Rear Position 4. Position the jack under the vehicle as shown. Front Position – 1500 Models 6-95.
Front Position – 2500 Models Front Tire Flat: If the flat tire is on a front tire of the vehicle, you will need to use the jack handle and only one jack handle extension. Attach the wheel wrench to the jack handle extension. Attach the jack handle to the jack (A).
Rear Position – All Other Models Rear Tire Flat: If the flat tire is on a rear tire of the vehicle, you will need to use the jack handle (B) and both jack handle extensions (C). Attach the wheel wrench (D) to the jack handle extensions (C). Attach the jack handle (B) to the jack (A).
5. Remove all of the wheel nuts. 6. T ake off the flat tire. 7. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
9. T ighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub. 10. T urn the wheel wrench counterclockwise to lower the vehicle. Lower the jack completely . 1 1. Tighten the nuts firmly in a crisscross sequence as shown by turning the wheel wrench clockwise.
. For bolt-on hub caps, line up the plastic nut caps with the wheel nuts and tighten clockwise by hand to get them started. Then tighten with the wheel wrench until snug. Secondary Latch System Y our vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system.
3. Loosen the cable by turning the wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 of Removing the Spare Tire and T ools on page 6 ‑ 89 .
8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle toward the front of the rear bumper . 9. Position the center lift point of the jack under the center of the spare tire. 10. T urn the wrench clockwise to raise the jack until it lifts the end fitting.
{ W ARNING: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely , make sure no one is behind you or on either side of you as you pull the jack out from under the spare.
Store the tire under the rear of the vehicle in the spare tire carrier . Refer to the following graphics and instructions to help you: A. Hoist Assembly B. Hoist Shaft C. Hoist Shaft Access Cover/Hole D. Jack Handle Extensions E. Wheel Wrench F . Hoist Cable G.
3. Assemble the two jack handle extensions (D) and wheel wrench (E) as shown. 4. Insert the open end of the extension (J) through the hole in the rear bumper (I) (hoist shaft access hole). 5. Raise the tire part way upward. Make sure the retainer is seated in the wheel opening.
T o store the tools, do the following: A. Wheel Blocks B. T ool Bag with Jack T ools C. Retaining Bracket D. Wing Nut Retaining T ool Bag E. Jack F . Wing Nut Retaining Wheel Blocks G. Jack Knob 1. Return the tools (wheel wrench, jack handle, and jack handle extensions) to the tool bag (B).
Spare Tire Y our vehicle, when new , had a fully-inflated spare tire. A spare tire may lose air over time, so check its inflation pressure regularly . See Inflation - Tire Pressure on page 6 ‑ 72 and Loading the Vehicle on page 5 ‑ 31 for information regarding proper tire inflation and loading your vehicle.
Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery . Dirt can damage carpet, fabric, leather , and plastic surfaces.
Do not clean the vehicle using: . A knife or any other sharp object to remove a soil from any interior surface. . A stiff brush. It can cause damage to the vehicle's interior surfaces. . Heavy pressure or aggressive rubbing with a cleaning cloth.
T o clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center . Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary , a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
W ashing Y our V ehicle The best way to preserve the vehicle's finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle.
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer . If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat.
Windshield, Backglass, and Wiper Blades Clean the outside of the windshield and backglass with glass cleaner . Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. W ash the windshield thoroughly when you clean the blades.
The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because they could damage the surface. Do not use chrome polish on aluminum wheels.
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away . Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer .
V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the Certification/T ire and Service Parts labels and certificates of title and registration.
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty .
Instrument Panel Fuse Block The instrument panel fuse block access door is located on the driver side edge of the instrument panel. Pull off the cover to access the fuse block.
Fuses Usage 9 Passenger Door Module, Driver Unlock 10 Power Door Lock 2 (Unlock Feature) 1 1 Power Door Lock 2 (Lock Feature) 12 Stoplamps, Center-High Mounted Stoplamp 13 Rear Climate Controls 14 Pow.
Center Instrument Panel Fuse Block The center instrument panel fuse block is located underneath the instrument panel, to the left of the steering column.
Underhood Fuse Block The underhood fuse block is located in the engine compartment, on the driver side of the vehicle. Lift the cover for access to the fuse/relay block. If the vehicle is a T wo-mode Hybrid, see the Two-mode Hybrid manual for more information.
Fuses Usage 5 Engine Control Module, Throttle Control 6 T railer Brake Controller 7 Front W asher 8 Oxygen Sensors 9 Antilock Brakes System 2 10 Trailer Back-up Lamps 1 1 Driver Side Low-Beam Headlamp.
Fuses Usage 34 Sunroof 35 Key Ignition System, Theft Deterrent System 36 Windshield Wiper 37 SEO B2 Upfitter Usage (Battery) 38 Electric Adjustable Pedals 39 Climate Controls (Battery) 40 Airbag Syste.
J-Case Fuses Usage 57 Cooling Fan 1 58 Automatic Level Control Compressor 59 Heavy Duty Antilock Braking System 60 Cooling Fan 2 61 Antilock Brake System 1 62 Starter 63 Stud 2 (Trailer Brakes) 64 Lef.
Capacities and Specifications If your vehicle is a Two-mode Hybrid, see the T wo-mode Hybrid manual for more information. The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 for more information.
Application Capacities English Metric T ransfer Case Fluid 1.6 qt 1.5 L Wheel Nut T orque 140 lb ft 190 Y † Oil filter should be changed at every oil change. All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual.
2 NOTES 6-128.
Section 7 Maintenance Schedule Maintenance Schedule ........................ .... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty .
At your dealer , you can be certain that you will receive the highest level of service available. Y our dealer has specially trained service technicians, uses genuine replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics.
When the Change Engine Oil Soon message displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: .
. Windshield wiper blade inspection for wear , cracking, or contamination and windshield and wiper blade cleaning, if contaminated. See Windshield, Backglass, and Wiper Blades on page 6 ‑ 1 14 . Worn or damaged wiper blade replacement. See Windshield Wiper Blade Replacement on page 6 ‑ 61 .
. Automatic transmission shiftlock control system check. See Owner Checks and Services on page 7 ‑ 9 . . Ignition transmission lock check. See Owner Checks and Services on page 7 ‑ 9 . . Hood and liftgate gas strut support service. Visually inspect gas strut for signs of wear , corrosion, cracks, loss of lubricant, or other damage.
. Evaporative control system inspection. Check all fuel and vapor lines and hoses for proper hook ‐ up, routing, and condition. Check that the purge valve, if the vehicle has one, works properly . Replace as needed. An Emission Control Service. The U.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection.
Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition T ransmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. . The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). . The ignition key should come out only in LOCK/OFF .
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer . Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Front Axle (2500 Series V ehicles with Four-Wheel Drive) SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678). Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678).
Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer . Maintenance Replacement Parts Part GM Part Number ACDelco Pa.
Engine Drive Belt Routing If your vehicle is a Two-mode Hybrid, see the T wo-mode Hybrid manual for more information. 7-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-17.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-18.
Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) U s e r s .
Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to GMC. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and T wo, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/gmc Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records .
Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use the T ext T elephones (TTYs), GMC has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with GMC by dialing: 1-800-GMC-8583 (462-8583).
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col.
Calling for Assistance When calling Roadside Assistance, have the following information ready: . Y our name, home address, and home telephone number . T elephone number of your location . Location of the vehicle . Model, year , color , and license plate number of the vehicle .
. Battery Jump Start: Service is provided to jump start a dead battery . . T rip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route. Additional travel information is also available.
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer can help minimize your inconvenience.
Public T ransportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer's shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service.
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle's resale value, and safety performance can be compromised in subsequent collisions.
Insuring Y our V ehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms.
. Gather the important information you will need from the other driver . Things like name, address, phone number , driver's license number , vehicle license plate, vehicle make, model and model year , V ehicle Identification Number (VIN), insurance company and policy number , and a general description of the damage to the other vehicle.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying General Motors.
Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors.
Current and Past Model Order Forms T echnical Service Bulletins and Manuals are available for current and past model GM vehicles. T o request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle's systems performed.
Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information. Refer to the navigation system operating manual for information on stored data and for deletion instructions.
2 NOTES 8-20.
A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . 6-4 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Active Fuel Management ™ .
Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-80 Audio Steering Wheel Controls . . . . . . . . . . . . . . . . . . 4-136 Navigation/Radio System, see Navigation Manual . . . . . . . . . . . . . . . . . . . .
C Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58 California Perchlorate Materials Requirements . . . . . . . . . . . . . . . 6-5 W arning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning (cont.) Underbody Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 16 W ashing Y our V ehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 12 Weatherstrips . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Information Center (DIC) . . . . . . . . . . . . . . . . . . . . 4-47 DIC Operation and Displays . . . . . . . . . . . . . . . . 4-48, 4-55 DIC Vehicle Customization . . . . . . . . . . . . . . . . . . . . . . . 4-72 DIC Warnings and Messages .
Engine (cont.) Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30 Drive Belt Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses Center Instrument Panel Fuse Block . . . . . . . . . . . . . 6-121 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . 6-1 18 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . 6-1 19 Underhood Fuse Block . . .
I Ignition Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 Infants and Y oung Children, Restraints . . . . . . . . . . . . 2-59 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72 Instrument Panel Brightness .
Lights Airbag Readiness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32 Antilock Brake System (ABS) Warning . . . . . . . . . . . . 4-37 Brake System Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36 Charging System .
Mirrors Automatic Dimming Rearview . . . . . . . . . . . . . . . . . . . . . 3-54 Manual Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54 Outside Automatic Dimming Mirror . . . . . . . . . . . . . . . . 3-57 Outside Convex Mirror .
P Paint, Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 16 Park Shifting Into . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-49 Shifting Out of . . . . . . . . . . . . . . . . . . . .
Reading Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Rear Air Conditioning and Heating System . . . . . . . . 4-27 Rear Air Conditioning and Heating System and Electronic Climate Controls . . . . . . . . . . . . .
S Safety Belts Care of . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 1 1 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-55 How to Wear Safety Belts Properly . . .
Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-37 Spare T ire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-107 Installing . . . . . . . . . . . . . . . . . . . . . . . .
T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-63 Aluminum or Chrome-Plated Wheels, Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 14 Buying New T ires .
V V ehicle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Remote Start . . . . . . . . . . . . . . .
Ein wichtiger Punkt beim Kauf des Geräts GM YUKON XL (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie GM YUKON XL noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für GM YUKON XL - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von GM YUKON XL reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über GM YUKON XL erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon GM YUKON XL besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von GM YUKON XL verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit GM YUKON XL. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei GM YUKON XL gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
