Benutzeranleitung / Produktwartung tracer2000 des Produzenten Giantec
Zur Seite of 39
tracer2000 Network Digital Video Recorder Hardware User’s Manual.
.
Copyright Notice This documen t may not, in whole or in part, b e reproduced or transmitted in any form or by means, electronic, mecha ni cal, or optical, includ i ng photocopying, reco rding, or storing in a retrie val system, or translated into any l a ng uag e in any form without the prior written noti ce of ag reement from us.
.
Giantec Internet Services Customer satisfaction is our numb er one concern. T o ensure that customer s receive the full benef it of our products, Giantec Internet Ser vices has been set u p to provide technical support, driver updat es , product inf o rmation, and user’ s manual updates.
.
Table of Contents CHAPTER I INTRODUCTION 1 Limited Warranty 1 Function Introduct ion 1 Features 2 CHAPTER II PACKAGE 3 CHAPTER III INSTALLATION 4 1. Indicator 5 2. Cable Connection 5 2.1 Connect VGA Mo nitor ...........................................
3.2 P/T/Z Setting ........................................................................................ 18 3.3 Pin Assignment o f COM2 ......................................................................... 18 3.4 Cable Connection ...............
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 o f 3 1 Chapter I Introduction Thank you for purchasing tracer2000 DVR; this manual will guide you through the setup, installation, and use of all our tr acer2000 systems.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 o f 3 1 Features The tracer2000 co mes with the following hardw are devices: Control Panel with IR Receiver One 1.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 3 o f 3 1 Chapter II Package Check the accessories accom pany with the system you purc hase as listed below. Wi th newer package release, the acce ssories are comp ac ted into an accessory box.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 4 o f 3 1 Chapter III Installation Front Panel View Rear Panel V iew Alarm Menu Dis p la y Pla y bac k Conf irm Removable A.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 5 o f 3 1 1. Indicator Power LED : The green light shows power is on. H.D. D. LED: The gr een light flash is HDD work ing. 2. Cable Connection Fol lowing is the basi c device must be pr epared befor e to start install ation complete system.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 6 o f 3 1 2.2 Connect Camera Cable to BNC Conne ctor 2.3 Connect to LAN Connector: P lug RJ-45 Connector to LAN Port Insert RJ-45 cable t o network LAN soc ket on the rear of tr acer2000.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 7 o f 3 1 2.4 Connect to Printer Port (Option) There are two types of printer port.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 8 o f 3 1 3. Power Connector 3.1 Connect Power Cord (110V ~ 240V Auto Switch) into the Power Socket Press “I” to star t up system and th en you can see the power LED will b e light in front of panel.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 9 o f 3 1 Chapter IV Pin Assignment 1. Internal Jumpers and Connectors.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 0 o f 3 1 1.1 Power Switch for ATX Power Supply (JP1) Signals JP1 Power ON/OF F 1-3 1.2 Reset / LED / Speaker (JP1) Signals JP1 Power LED , Pin9+, Pin10- 9-10 External Speaker 14-20 HDD LED, Pin8+, Pin7- 7-8 System R eset S witch 5-6 SUSLED Pin4+, Pin2- 2-4 P .
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 1 o f 3 1 1.6 COM2 Mode Select (JP3 ) Mode JP3 RS232 3-5, 4-6, 9-11, 10-12, 17-18 RS422 1-3, 2-4, 7-9, 8-10, 15- 16 RS485 1-3, 2-4, 7-9, 8-10, 13- 14 1.7 CPU FS B Select (JP4) Function JP4 Auto by CPU 1-3, 2-4 66MHz 3-5, 4-6 1.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 2 o f 3 1 1 2 43 44 1.10 Parallel / Printer Connector (PRN) Pin No. Signal Pin No.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 3 o f 3 1 1 5 1.12 General Purpose Input / Out put (J3) Pin No. Signal Pin No. Signal 1 GPIO-0 2 Audio IN3 3 GPIO-1 4 AGND 5 GPIO-2 6 Audio IN2 7 GPIO-3 8 AGND 9 GPIO-4 10 Audio IN1 11 GPIO-5 12 AGND 13 GPIO-6 14 Audio IN0 15 GPIO-7 16 GND (for GPIO) 1.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 4 o f 3 1 A1 B1 A49 B49 B52 A52 B62 A62 COMPONENT SIDE SOLDER SIDE 1.14 PCI Bus Pin Assignment Pin No.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 5 o f 3 1 1 5 15 10 2. External Connector 2.1 CRT Display Connector (V GA) Pin No. Signal Pin No. Signal 1 RED 9 K ey 2 GREEN 10 GND 3 BLUE 11 N/C 4 N/C 12 DCDA 5 GND 13 H-SYNC 6 GND 14 V- SYNC 7 GND 15 DCDA 8 GND 2.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 6 o f 3 1 1 6 5 9 1 6 5 9 2.5 COM1 Connector RS232 Connector (COM1) Pin No. Signal 1 DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RT S 8 CTS 9 RI 2.6 COM2 Connector RS232 / RS422 / RS485 Co nnector (COM2) Pin No.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 7 o f 3 1 3. Ethernet Connector (RJ-45) Drawing of Ethernet Connector RJ-45 Pin No. Signal 1 TX+ 2 TX - 3 RX+ 4 NC 5 NC 6 RX - 7 NC 8 NC 3.1 Connectors The connectors all ow this main board to connect with other p arts of the system.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 8 o f 3 1 1 6 5 9 3.2 P/T/Z Setting The P/T/Z Setting complies with LI LIN or PELCO. Protocol has been previously attached to the COM ports. Y ou may control the camera via arrow b uttons.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 1 9 o f 3 1 Chapter V CMOS Setting 1. Introduction This manual discusses Award TM setup program buil t into the ROM B IOS. The set up program allows users to mod ify the basic system c onf iguration.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 0 o f 3 1 2.1 Standard CMOS Features Use this menu for basic system conf iguration.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 1 o f 3 1 2.2 Advanced BIOS Features Use this menu to set the Advanced Features av ailable on your system.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 2 o f 3 1 2.3 Advanced Chipset Features Use this menu to change the values in the chipset register s and optimize your system’s performance.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 3 o f 3 1 SDRAM CAS Latency Time 3 Item Help SDRAM Cycle Time Tras/Trc 7/9 SDRAM RAS-to -C AS Delay 3 Menu Level SDRAM RA.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 4 o f 3 1 2.4 Integrated Peripherals Use this menu to specify your setting f or integrat ed peripherals.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 5 o f 3 1 2.5 Power Management Setup Use this menu to specify your settings for power management.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 6 o f 3 1 2.6 PnP / PCI Conf iguration This entry appears if your system supports P nP / PCI.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 7 o f 3 1 2.8 Frequency / Voltage Control Use this menu to specify your settings for frequency / voltage control.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 8 o f 3 1 . Chapter VI System HDD Installation Guide Follo w the step to setup HD D drawi ng box. 1. Remove th e screws on the case. (Mark ed in while circles) Remove the screws on the case.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 2 9 o f 3 1 2. Take off the upper cover and remove the screws. Remove t he sc rew.
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 3 0 o f 3 1 3. Remove HDD tray, and install HDD prop erly..
tracer2000 Network DVR Hardware User ’s Manual V e r s i o n 3 . 1 P a g e 3 1 o f 3 1 4. Insert the assembled HDD tray int o tracer2000, and conne ct both power and HDD.
Ein wichtiger Punkt beim Kauf des Geräts Giantec tracer2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Giantec tracer2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Giantec tracer2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Giantec tracer2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Giantec tracer2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Giantec tracer2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Giantec tracer2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Giantec tracer2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Giantec tracer2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
