Benutzeranleitung / Produktwartung EXT-HDMI1.3-CAT6-8X des Produzenten Gefen
Zur Seite of 66
www.gefen.com ® ® EXT -HDMI1. 3 - C AT 6 - 8 X User Manua l.
.
ASKING FOR ASSIST ANC E R ev B5 T echnical Su pp or t : T elephone ( 818 ) 772-910 0 ( 800 ) 545-690 0 Fax ( 818 ) 772-912 0 T echnical Su pp ort Hours : 8 :00 AM to 5:00 PM Monda y throu g h Frida y , Paci fi c Tim e Write T o : G e f en, LL C . c/ o C ustomer S ervic e 2 0600 Nordho ff S t C hatsworth, C A 9131 1 www .
CONTENT S 1 Intr oduc ti on 2 O peration Notes 3 F ea t u r es 4 S ender Unit La y out - Fron t 5 S ender Unit Descriptio n 6 S ender Unit La y out - Bac k 7 S ender Unit Descriptio n 8 Receiver Unit .
1 INTRODUCTIO N C on g ratulations on y our purchase o f the 8x C A T6 Extender f or HDMI. Y our c omplete satis f action is ver y important to us. G efen G e f en delivers innovative, pro g ressive computer and electronics add-on solutions that harness inte g ration, extension, distribution and conversion technolo g ies.
READ THESE NOTES BEFORE INST ALLING OR OPERA TING THE 8X CA T6 EXTENDER FOR HDMI • C A T -6a cables can be used up to 200 f eet ( 60 meters ) . • S hielded (S TP ) C A T -6a is recommended.
3 FEA TURE S Su pp orted HDMI 1.3 Features • 225 MHz ( up to 12 bit YUV 444 @ 1080p ) • Deep C olor • Dolb y T rueHD and DT S -HD Master Audi o • Lip- Sy nc • C E C Pass-Throu gh Features • Extends HDMI 1.
4 SENDER UNIT LA YOU T 2 3 1 Fron t.
5 Fron t 1 S tandby Button S ets the 8x C A T6 Extender f or HDMI into S tandb y Mode. 2 I R Senso r R eceives si g nals f rom the IR Remote C ontrol. 3 P ower Indicato r This LED will turn bri g ht red once the lockin g power suppl y has been properl y co nn ec t ed .
6 SENDER UNIT LA YOU T 2 5 7 3 6 8 1 4 Back.
7 SENDER UNIT DESCRIPTION S Back 1 R S-232 Serial Port ( Input ) The 8x8 Matrix ma y be switched remotel y usin g serial communications with an y o f fi ce computer or a control automation device b y connectin g to this port. S ee p a g e 25 f or details.
8 RECEIVER UNIT LA YOU T Fron t 3 1 5 4 2.
9 RECEIVER UNIT DESCRIPTION S Fron t 1 C ontrol Buttons ( 1 - 8 ) When connected to an y 8x8 Matrix f or HDMI, these remote buttons on the R eceiver unit can switch between the 8 Hi-De f inputs connected to the 8x8 Ma trix fo r HDMI. 2 I R Senso r C ontrol the Receiver unit b y pointin g the IR Remote C ontrol to the IR S ensor .
10 RECEIVER UNIT LA YOU T Back 3 6 5 4 2 1.
1 1 RECEIVER UNIT DESCRIPTION S Back 1 C ontrol Buttons ( 1 - 8 ) When connected to an y 8x8 Matrix f or HDMI, these remote buttons on the R eceiver unit can switch between the 8 Hi-De f inputs connected to the 8x8 Ma trix fo r HDMI. 2 I R Extender Por t U sed to extend the IR S ensor ran g e o f the Receiver unit.
12 1 Activity Indicato r This LED will be activated momentaril y each time a button is pressed. 2 Input Source Selection Buttons ( 1 - 8 ) These buttons are used to select which input source is routed to the HDTV displa y .
1 3 RMT -8IR REMOTE INST ALLA TIO N Installin g the RMT -8IR Batter y 1. R emove the batter y cover on the back o f the IR Remote C ontrol unit. 2. Insert the included batter y into the open batter y slot. The positive ( + ) side o f the batter y should be f acin g up.
1 4 Settin g the IR Remote Channel on the RMT -8IR In th e e v e nt th a t IR co mm a n ds f r o m o th e r r e m o t e co ntr o l s co n fl i c t with th e s upplied RMT -8IR Remote, chan g in g the remote IR channel will fi x this issue. The RMT -8IR Remote has a bank o f DIP switches f or settin g the Remote IR c h a nn e l.
15 CONNECTING AND OPERA TING TH E 8 X CA T6 EXTENDER FOR HDMI How to Connect the 8x CA T6 Extender for HDMI ( Matrix Mode ) 1. U sin g an y 8x8 Matrix f or HDMI as a source, connect an HDMI cable f rom H DMI O ut 1 on the 8 x 8 Matrix to HDMI In 1 on the 8 x C AT 6 Extender f or H DMI S ender unit.
1 6 How to O p erate the 8x CA T6 Extender for HDMI ( usin g an 8x8 Matrix ) The f ront panel o f each Receiver unit f or the 8x C A T6 Extender f or HDMI c ontains a set o f LED indicators which corresponds to an input ( source ) on the 8 x8 Matrix device.
17 How to Connect the 8x CA T6 Extender for HDMI with RS-232 control t o the 8x8 Matrix for HDMI and to the controlled devic e 1. Follow steps 1 - 6 on How to C onnect the 8x C A T6 Extender f or HDMI ( see p a g e 1 1 ) .
1 8 How to Connect the 8x CA T6 Extender for HDMI ( Stand-alone Mode ) The 8x C A T6 Extender f or HDMI is dependent upon an external 8x8 Matrix to m ana g e all the zone switchin g . When used as a stand-alone, without the 8x8 M atrix attached, the product f unctions as a one-to-one extender f or each HDMI u nit.
19 Routin g Sources usin g the Optional RMT -8IR Remote Uni t ( Matrix Mode ) There are a total o f 8 buttons on the RMT -8IR remote, which represent each o f the 8 buttons on the Receiver unit. Example 1 : R oute the source connected to HDMI In 3 (f rom the 8x8 Matrix ) on t he S ender unit to the displa y connected to HDMI O ut 2.
2 0 How to O p erate the 8x CA T6 Extender for HDMI ( Stand-alone Mode ) When the 8x C A T6 Extender f or HDMI is used without an 8x8 Matrix, it can onl y be used as a n HDMI e xt e n de r.
21 How to E q ualize the 8x CA T6 Extender for HDMI ( Matrix Mode / Stand-alone Mode ) The 8x C A T6 Extender f or HDMI Receiver unit has an equalization trimpot t o c ompensate f or variances that can be f ound in di ff erent C A T -6a cable brands.
2 2 Controllin g the Receiver Unit usin g RS-232 ( Matrix Mode ) 1. Prepare the Receiver unit b y connectin g an R S -232 cable f rom the computer or other controllin g device to the R S -232 serial port on the back o f the R eceiver unit ( see pa g e 6 - 7 ) .
23 D efault settin g s for DIP switches DIP S witc h P os iti on 1 O FF 2 O FF 3 O FF 4 O FF D IP Switch Location ( Matrix Mode / Stand-alone Mode ) O n the bottom o f each Receiver unit, there are f our ( 4 ) DIP switches. E ac h DIP s witch per f orms a di ff erent f unction.
24 D IP SWITCH CONFIGURA TIO N D IP Switches ( Matrix Mode / Stand-alone Mode ) D IP 1 - EDID Mana g emen t • O FF - Local EDID When Local EDID mode is used, the EDID will be assembled b y cop y in g all video and audio f eatures o f the connected device.
2 5 54321 9876 12345 6789 Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface RS-232 SERIAL CONTROL INTERF AC E RS-232 Settin g s Bits per second ............................................................................
26 RS-232 SERIAL FUNCTIONS - SENDER UNI T Functions S y nta x The s y ntax f or each f unction is alwa y s the same : #C haracter as the start fl a g → Function name → S pace ( _ ) as f unction name e nd fl a g → Parameter 1 → S pace → Parameter n → C arria g e Return ( r ) → S ample : # FunctionName_param1_param2_param3_param4.
2 7 RS-232 SERIAL FUNCTIONS - SENDER UNI T # LOEDIDTOLO Function The # L O EDIDT O L O f unction loads the speci fi ed EDID fi le to a speci fi ed local input via R S -232.
28 RS-232 SERIAL FUNCTIONS - SENDER UNI T IP Con fi g uration - Sender Uni t Function D escri p tion #S IP ADD S peci fi es a new IP address #S NETMA S K S peci fi es a new net mas k #SG A TEWA Y S.
2 9 RS-232 SERIAL FUNCTIONS - SENDER UNI T # SNETMASK Function The #S NETMA S K f unction speci fi es a new net mask. Syntax y : # SNETMASK p aram1 p aram2 p aram3 p aram4 Pa r a m e t e r s : p aram.
3 0 RS-232 SERIAL FUNCTIONS - SENDER UNI T # SPORT Function S peci fi es a new port. Syntax y : # SPORT p aram 1 Pa r a m e t e r s : p aram 1 Port [0 - 255] N o t es : A reboot is required a f ter usin g this f unction. # PRWEBADD Function Prints the current IP con fi g uration on the screen.
31 RS-232 SERIAL FUNCTIONS - SENDER UNI T G eneral Functions Function D escri p tion # A C TIVEB O L O En ab l es th e boo t l oade r # BLA S TER S ets the Receiver unit blaster mod e # BRID G EM En a.
3 2 RS-232 SERIAL FUNCTIONS - SENDER UNI T # BLASTER Function The # BLA S TER f unction sets the Receiver U nit blaster mode. Syntax y : # BLASTER p aram1 p aram 2 Pa r a m e t e r s : p aram 1 Receiv.
33 RS-232 SERIAL FUNCTIONS - SENDER UNI T # CT ARGET Function The #C TA R G ET f unction de fi nes how to send routin g commands to the Matrix. Syntax y : # CTARGET p aram 1 Pa r a m e t e r s : p ar.
34 RS-232 SERIAL FUNCTIONS - SENDER UNI T # HPDMODE Function The # HPDM O DE f unction sets HPD to low (O FF ) or hi g h (O N ) on the HDMI inputs. Syntax y : # HPDMODE p aram1 p aram 2 Pa r a m e t e.
3 5 RS-232 SERIAL FUNCTIONS - SENDER UNI T # MASKOUT Function The # MA S K O UT f unction allows blankin g o f selected outputs. Syntax y : # MASKOUT p aram1 p aram 2 Pa r a m e t e r s : p aram 1 O u.
36 RS-232 SERIAL FUNCTIONS - SENDER UNI T # RMTIRADD Function The # RMTIRADD f unction sets the IR channel f or the Matrix. Syntax y : # RMTIRADD p aram 1 Pa r a m e t e r s : p aram 1 IR channel [0 -.
3 7 RS-232 SERIAL COMMANDS - SENDER UNI T Command S y nta x S impli fi ed s y ntax was used f or command implementation f or f aster operation with th e de vi ce .
38 RS-232 SERIAL COMMANDS - SENDER UNI T U sin g parameters with the F Command Permits disablin g / enablin g o f +5 V f or Fiber O ptic Extenders. Syntax y : f p aram1 p aram 2 Pa r a m e t e r s : p.
3 9 RS-232 SERIAL COMMANDS - SENDER UNI T R Command The R command allows speci fi c routin g o f inputs and outputs when controllin g the 8 x C AT 6 f or HDMI S ender unit.
4 0 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T Functions S y nta x The s y ntax f or each f unction is alwa y s the same : #C haracter as the start fl a g → Function name → S pace ( _ ) as f unctio.
41 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # EDIDMODE Function The # EDIDM O D E fu n c ti o n se t s th e EDID m ode . Syntax y : # EDIDMODE p aram 1 Pa r a m e t e r s : p aram 1 EDID Mode [0 - 1] V a l ue M eanin g 0 L oca l 1 Pass throu gh N o t es : This f unction onl y works a f ter the hardware inter f ace has been disabled.
4 2 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # PRLOEDID Function The # PRL O EDID f unction reads the local EDID and spools it to the serial port. Syntax y : # PRLOEDI D Pa r a m e t e r s : N o n e # PRDSEDID Function The # PRD S EDID f unction reads the downstream EDID and sends it to the serial p ort.
43 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T G eneral Functions Function D escri p tion # A C TIVEB O L O En ab l es th e boo t l oade r # BLA S TER S ets the blaster mod e # DEEP CO L O R S ets the de.
44 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # BLASTER Function The # BLA S TER f unction sets the Receiver U nit blaster mode. Syntax y : # BLASTER p aram1 p aram 2 Pa r a m e t e r s : p aram 1 Recei.
4 5 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # EQULIZE Function The # E Q ULIZE f unction sets equalizer level on the Receiver Unit. Syntax y : # EQULIZE p aram 1 Pa r a m e t e r s : p aram 1 Equalizer level [0 - 7] N o t es : This f unction onl y works a f ter the hardware inter f ace has been disabled.
46 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # HPDMODE Function The # HPDM O DE f unction sets HPD to low (O FF ) or hi g h (O N ) on the HDMI inputs. Syntax y : # HPDMODE p aram1 p aram 2 Pa r a m e t.
4 7 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # RMTIRADD Function The # RMTIRADD f unction sets the IR channel f or the Matrix. Syntax y : # RMTIRADD p aram 1 Pa r a m e t e r s : p aram 1 IR channel [.
48 RS-232 SERIAL FUNCTIONS - RECEIVER UNI T # USERIN Function The #US ERIN f unction sets the user hardware inter f ace. Syntax y : # USERIN p aram1 p aram 2 Pa r a m e t e r s : p aram 1 M ode [0 - 2.
4 9 RS-232 SERIAL COMMANDS - RECEIVER UNI T Command S y nta x S impli fi ed s y ntax was used f or command implementation f or f aster operation with th e de vi ce .
50 RS-232 SERIAL COMMANDS - RECEIVER UNI T R Command The R command routes the Receiver Unit to a speci fi c input. Syntax y : r p aram 1 Pa r a m e t e r s : p aram 1 H DMI Input [1 - 8] Example: r 4 routes the Receiver Unit to Input 4.
5 1 IP CONTROL The G e f en 8x C A T6 Extender f or HDMI supports IP-based control usin g an inte g rated Web inter f ace. T o access this f eature, an IP address, subnet, g atewa y , and port number need to be set on the 8x C A T6 Extender f or HDMI ( D efault IP: 192.
52 IP CONTROL IP CONFIGURA TIO N Th e IP CONFIGURA TION p a g e is used to set the IP settin g s that will be used to access the Web inter f ace. The f ollowin g items can be con fi g ured f rom this menu. • IP Address ( De f ault: 192.168.0.70 ) • S ubnet ( De f ault: 255.
5 3 IP CONTROL BACKUP / REST OR E Th e Backu p/ Restore p a g e is used to backup and restore complete setup c on fi g urations. Note: This f eature will be implemented in a f uture release.
5 4 IP CONTROL P OWER MANAGEMEN T Th e P OWER MANAGEMEN T p a g e is used to set optional +5V power on an input to power speci fi c optional devices. The current status o f this f eature f or e ach input can be viewed on this pa g e. T o set this f eature f or each input f ollow the steps below .
55 NETWORK CABLE WIRING DIAGRA M G e f en recommends the TIA / EIA-568-B wirin g option. Please adhere to the table below when fi eld-terminatin g the C A T -6 cable f or use with G e f en products.
5 6 FIRMW ARE UPDA T E Firmware U p date Procedur e T o be g in the update procedure, the unit ’ s Boot Loader must be activated. T o activate the Boot Loader , f ollow the procedure outlined below : 1. C onnect an R S -232 cable f rom the computer to the R S -232 port on th e 8 x C AT 6 Extender f or HDMI.
57 FIRMW ARE UPDA T E 1 1. C onnect the R S -2 3 2 cable to the Receiver unit. 12. R epeat steps 4 - 7 and upload RHDMID C A T6x8_e_x_x.bin. 1 3 . R epeat step 1 1 - 13 f or each Receiver unit.
5 8 SPECIFICA TION S Video Ampli fi er Bandwidth ....................................................................... 225 MHz Input Video S i g nal.....................................................................................1.2 V p- p Input DD C S i g nal.
59 W ARRANTY G e f en warrants the equipment it manu f actures to be f ree f rom de f ects in material and workmanship. I f equipment f ails because o f such de f ects and G e f en is noti fi ed with.
60 l wIP is licenced under the B S D licence : C op y ri g ht ( c ) 2001-2004 S wedish Institute o f C omputer S cience. All ri g hts reserved. R edistribution and use in source and binar y f orms, with or without modi fi cation, are permitted provided that the f ollowin g conditions are met : 1.
.
R ev B5 20600 Nordho ff S t. , C hatsworth C A 9 1 3 1 1 1- 800 -545- 6900 8 1 8 -77 2 - 9 1 00 f ax: 8 1 8 -77 2 - 9 1 20 www .ge f en.com support @ ge f en.
Ein wichtiger Punkt beim Kauf des Geräts Gefen EXT-HDMI1.3-CAT6-8X (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Gefen EXT-HDMI1.3-CAT6-8X noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Gefen EXT-HDMI1.3-CAT6-8X - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Gefen EXT-HDMI1.3-CAT6-8X reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Gefen EXT-HDMI1.3-CAT6-8X erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Gefen EXT-HDMI1.3-CAT6-8X besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Gefen EXT-HDMI1.3-CAT6-8X verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Gefen EXT-HDMI1.3-CAT6-8X. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Gefen EXT-HDMI1.3-CAT6-8X gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
