Benutzeranleitung / Produktwartung 2701 des Produzenten Gateway
Zur Seite of 27
For 2 7 0 1 2Wire Gateway Installation Guide.
Notice to Users ©2006 2Wire, Inc. All rights reser ved. This manual in whole or in par t, may not be reproduced, translated, or reduced to an y machine- readable form without prior written approval.
Contents Getting Started 1 Remove or Disable Conflicting Applications 1 Check Your Computer’s Brow ser and System Requirements 1 Browser Requirements 1 System Requirements 1 Connect the First Comput.
1 Getting Started Remove or Disable Conflicting Applications Internet sharing software and PC based firew all applicati ons typically interfere with the 2Wire gatew a y , and should be removed or disabled before you install the gate wa y . The 2Wire gatew ay pro vides the same features as the products listed below .
2 Connect the First Computer to the Gateway Congratulations on the purchase of your 2Wire gatew a y . T o install your gatewa y and configure your networ k, follow these steps.
Connect the Fir st Computer to the Gatew ay 3 T o install the DS L filter : 1. Locate the phone jack where you wa nt to connect your 2Wire gatewa y . 2.
Connect the Fir st Computer to the Gatew ay 4 Ethernet Connection Figure 1. Gatewa y Connected Via Ethernet 1. Connect the provided pow er adapter from the gatewa y’ s POWER por t to an electrical outlet. The POWER light on the front of the gatew ay should be green.
Connect the Fir st Computer to the Gatew ay 5 Wireless Connection Requires wireless-enabled notebook or a computer with an 802.11b/g wireless network adapter installed. Wireless adapters can be purchased from your ser vice provider . Figure 2. Gatewa y Connected Via Wireless 1.
Connect the Fir st Computer to the Gatew ay 6 Non-2Wire Wireless Adapter Configuration Locating the Serial Number and Wireless Encr yption Ke y The serial number of your 2Wire gatew a y is used as the networ k name (SSID). Beneath the serial number is a ten-digit number which is used as the encr yption ke y .
Connect the Fir st Computer to the Gatew ay 7 USB Connection Figure 3. Gatewa y Connected Via USB 1. Connect the provided A C power adapt er from the 2Wire gate wa y’ s POW ER por t to an electrical outlet. The POWE R light on the front of the gatew ay should be green.
Connect the Fir st Computer to the Gatew ay 8 Install the 2Wire Gatew a y USB Driver - Windows 1. P ower on your computer and place the 2 Wire CD in your computer’ s CD-ROM drive. 2. If the Add Hard ware Wizard displa ys, follow the on -screen instructions.
9 Run the 2Wire Setup Wizard Windows XP/2K/ME/98SE 1. Inser t the 2Wire CD and follow the on-screen inst ructions. If the 2Wire Setup Wizard does not automatically star t: − Double-click the My Computer icon located on the desktop. − Double-click the icon that corresponds to your CD-ROM drive.
10 Add Computers to the Network After your first computer is connected to the 2Wire gatewa y and your Inter net connection has been established, you can connect other computers to the network. Use any of the followin g methods to connect additional computers to your networ k.
Add Computers to the Networ k 11 Ethernet Connection Figure 4. Gatewa y Connected to Second Computer Via Ethernet 1. Connect an Ethernet cable from the any a vailable LOCAL ETHERNET 1 por t on the gatewa y to your computer’ s Ethernet por t. 1. The number of Ethernet por ts var y by model (from one to four).
Add Computers to the Networ k 12 USB Connection Figure 5. Gatewa y Connected to Second Computer Via USB 1. Connect the provided blue USB cable from the gatew ay’ s USB-PC port to the USB por t on your computer . 2. Install the USB driver (refer to page 8 for instructions).
Add Computers to the Networ k 13 Wireless Connection Figure 6. Gatewa y Connected to Second Computer Via Wireless Requires a computer with an 802.11b/g wireless net work adapter installed. Wireless adapters are purchased separately from the 2Wire gatew a y .
14 Diagnostics Understanding Broadband Redirect Messages If the 2Wire gatew ay detects a connection problem or an intermittent ser vice error , it generates an error or aler t (Broadband Redirect Message) and displa ys the message within your W eb browser .
Diagnostics 15 No DSL Connection - Unable to T rain When setting up a DSL broadband network, all active phone devices must ha ve a phone line filter installed. Without the filter , the DSL connection will be unstable, resulting in a poor or no DSL connection.
Diagnostics 16 Broadband Link is Currently Not Available - DSL Connection Issue This error message is displayed bec ause the gatewa y was unable to establish a broadband network connection. Check to ensure that all cables are correctly connected, and the cable end securely attached to the por t.
Diagnostics 17 Router Behind Router Detected If the gatew a y detects the presence of a third-par ty r outer , the Router Behind Router error page displays. If a third-par ty router is connected to the 2Wire gatew a y , networ k instability can result because both devices are tr ying to manage private IPs via NA T .
Diagnostics 18 Understanding the Indicator Lights The 2Wire gatew ay ha s numerous indicator lights that can be used to diagnose installation and connection problems. The following table describes how to interpret the indicator lights. Pow e r Light Operating State OFF The gatew a y is not getting power .
Diagnostics 19 DSL Light Operating State OFF The gatew a y is powered off or boo ting up. Blinking green (slow) The gatewa y is attempting to establish a connection to your broadband ser vice(s). Blinking green (fast) The gatew ay has been unable to connect to the DSL signal for more than three minutes.
20 Appendix A: Install the Gateway on Other Operating Systems Follow these instr uctions if you are using an operating system that is not suppor ted by the 2Wire CD (such as any Macin tosh OS prior to 10.
Appendix A: Install the Gatew ay on Other Operating Systems 21 USB Connection Figure 8. Gatewa y Connected Via USB (Macintosh) 1. Install DSL phone filters according to the instr uctions on page 2. 2. Inser t the 2Wire CD in the computer’ s CD-ROM drive.
Appendix A: Install the Gatew ay on Other Operating Systems 22 9. V erify that “Connect Via: 2Wire USB Remote NDIS…” is selected to set the networ k adapter as active. 10. Click Save to complete your installation. 11. Proceed to “Configuring the Internet Connection” on page 22.
23 Regulatory Information Declaration of Conformity T rade Name: 2Wire Responsible P ar ty: 2Wire, Inc. Address: 1704 Automation P arkway San Jose, CA T elephone: 408.
Regulator y Information 24 If the terminal equipment causes harm to the telephone networ k, the telephone compan y will notify you in advance that temporar y discontinuance of ser vice ma y be required. But if advance notice is not practical, the telephone compan y will notify the customer as soon as possible.
Ein wichtiger Punkt beim Kauf des Geräts Gateway 2701 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Gateway 2701 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Gateway 2701 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Gateway 2701 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Gateway 2701 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Gateway 2701 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Gateway 2701 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Gateway 2701. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Gateway 2701 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
