Benutzeranleitung / Produktwartung TR-1 des Produzenten Garmin
Zur Seite of 48
1 Safety Y ou ar e r esponsible for the safe and prudent operation of your vessel. Y our TR-1 Autopilot is a tool that will enhance your capability to operate your boat and catch sh. It does not r elieve you fr om the r esponsibility for safe operation of your vessel.
2 3 Contents Section II: Setup..........................................29 Dockside Setup 26 Sea T rial Setup 27 Compass Calibration 27 Autotune 28 Set North 29 Fine T uning 30 Section III: T roubleshooting........................31 Section IV : Changing Codes.
2 3 Compass Ball: 120-2250-00 3-ea. Pan head sheet metal screws #8x1”: 310-0071-03 Compass Ball bracket Compass Ball capture cage All screws and washers are included in the accessory pack Handheld: 120-2520-00 TR-1 Gladiator 2.1 Liter System Parts List Pump Unit: Pump Unit: 120-2568-00 4 ea.
4 5 Deckmount: 120-2515-00 2 ea. #4 x 3/8” Pan Head Screw 310-0072-03 W arning Horn: 120-2525-00 T ach Sensor Cable: 120-2510-00 Shadow Drive/Flow Switch 120-2580-00 Battery Cable with Fuse: 120-2530-00 Accessory Pack 120-2570-00: 10 ea.wire connectors: 290-0100-00 3 ea.
4 5 Pump & Motor *Shadow Drive 1) Mount Horizontally and as level as possible 2) May be located in the Port or Starboard Hydraulic Lines 3) Use a length of hose between.
6 7 Pump & Motor ! Before starting the hydraulic installation, please verify the type of hydraulic steering in the boat. If it does not match the hydraulic layouts in this manual, call TR-1 technical support for specific installation procedures.
6 7 # 3 Remote/ Handheld Compass Ball Shadow Drive W arning Horn Deckmount On/Off Switch # 2 # 1 # 5 # 4 Orange and Black T wisted W ire Red and Black T wisted W ire Red ( + ) Black( - ) Blue (- ) Ora.
8 9 NOTE: Before proceeding with the installation, read these instructions thoroughly . TR-1 Autopilots cannot accept responsibility for installations where instructions have not been followed, where substitute parts have been used, or where modications have been made to our pr oducts.
8 9 Section I Installation Check List Please read all installation instructions befor e proceeding with the install! The TR-1 Gladiator is designed and manufactured to meet the harsh marine environment. However , no electronics can perform as intended unless installed, setup and maintained properly .
10 1 1 TR-1 Gladiator Specications Pump Set 15.375” L x 7.5”T x 7.5”W ECU 6.5” H x 7” W x 2” D Compass Ball 3.6”Diameter Cable Length 20’ HH/Remote 5” x 2.
10 1 1 Pump Unit: This pump unit is designed for cylinder or cylinders equilivant to 10 - 25 cubic inches only . The Pump unit will need to be mounted within at least 20” of the ECU . It will need to be mounted in a horizontal position to a solid surface.
12 13 It is recommended that before connecting the hydraulic lines to the pumpset, ensure all the hydraulic lines in the steering system have been ushed and that the hydraulic oil is free of any contamination, which may enter the pumpset or Shadow Drive valve and cause it to fail.
12 13 Installation Of Pump Unit Hydraulic Pump and Motor Assembly: Mount the pump unit using the template provided. Mount the pump to a solid surface using the #14 x 1” pan head sheet metal screws provided.
14 15 E lectronic Control Unit (ECU) : Mount the ECU using the template provided. Mount it to a solid surface using the four #8 x 5/8” Phillips Pan Head screws included in the accessory pack. The ECU will need to be mounted within 20” of the pump unit.
14 15 Step two: Placing ball in bracket Place the ball, wires down, into the bracket and capture it by snapping the cage over the ball, sliding the tips of the cage between the ball and the legs of the bracket. Do the two legs without the thumbscrew rst.
16 17 NMEA 0183 Connections The Autopilot does not need to connect to a GPS for the autopilot to work, but if you want to use waypoint steering you must connect to a GPS and set North see page 29. The Autopilot will accept NMEA input from two GPS units and transmit NMEA to one receiving device.
16 17 The TR-1 Autopilot is designed in conformance with the NMEA 0183 standard. The TR-1 will communicate reliably and safely when connected to other devices that meet this standard with the normal wire connections. Some manufacturers imply that they conform to the standard when in fact they do not.
18 19 The shadow drive valve must be mounted in a level horizontal position using the cable ties & mounts with screws included in installation pack It should be mounted in-line between the helm and the hydraulic pump and motor . It must be mounted lower than the helm, but higher than the pump.
18 19 Fig 23 T o pump & Cylinder T o Helm (Close up view) Compass Ball Shadow Drive # 4 Red Black Brown Green The shadow drive valve must be mounted in a level horizontal position using the cable ties & mounts with screws included in installation pack See Fig.
20 21 The electrical connections for the warning horn are made at the compass ball. The Black ( - ) and Red (+ ) wire on the warning horn connect to the Blue (- ) and Orange ( + ) coming from the Compass Ball. Mount the warning horn using the cable tie and mount with screw included in your installation kit.
20 21 If the material you wish to mount the Deckmount switch in is less than ” thick: Drill a hole 15/32” diameter , and perpendicular to the surface. Unscrew the waterproof bezel. Use the washers on the neck of switch to take up excess space. Put the switch button, with washer , through the hole from back side, see Fig.
22 23 Corded Mount: Different options are available. TR-1 has an optional clip than can be purchased separately , Fig. 29. Fig. 29 Flush Mount: Remove the back cover of handheld. Using the back of the handheld as a guide drill 2 1/4” holes into your dash.
22 23 T ach Sensor Cables: The tachometry connection is a very intricate part of the Gladiator and must always be connected . In most cases this can be simply done behind the dashboard at the tachometer display or just before the display .
24 25 T achometry Connections Honda + Gray (positive) - Black (negative) On most Hondas the pulses per revolution to 2. For the 6 cyl VTEK it must be set to 1 (Use Setup Code 267) Mercury (not applica.
24 25 Connections to the battery should be made last. Connect the ground side rst. Connect the black (-) wire to the negative (-) side of the battery rst.
26 27 Section II Dockside Setup and Sea T rial Setup of Autopilot Y our autopilot needs to be setup and tuned to your boat dynamics and motor conguration.
26 27 Sea T rial Setup: Steps 10-15 will need to be performed on open water , free of obstacles. 10. Calibrate your compass. The autopilot compass is made with a uxgate. Like all compass installations, uxgate installations are susceptible to local magnetic disturbances that will cause erroneous heading outputs.
28 29 1 1. Restart the autopilot by pressing and releasing the Deckmount On/Off switch. 12. Autotune. The autopilot’ s autotune function can really simplify the problem of adjusting the feedback gains. The autotuner will adjust the gains well enough that you may not need to do any additional adjustments at all.
28 29 14. Set North. This needs to be done if any GPS or radar overlay functions are going to be used. T o run a GPS course requires that the autopilot compass is in agreement with the GPS’ s magnetic map. Y ou need to set North with the pilot in standby mode.
30 31 15. Fine T uning. (Optional) If autotune did a pretty good job but you feel that the dead idle response of the pilot is a bit “twitchy”, try to eliminate the twitch by increasing the Low RPM Limit [ Code 357 ] to a few hundred RPM more than your dead idle RPM.
30 31 Section III T rouble Shooting Guide Autopilot does not hold heading. 1. Did you calibrate the compass? a. Calibration must be done for the autopilot to work correctly . See pages 30 2. Has some kind of magnetic interference been introduced within 24” of the Compass? 3.
32 33 Section IV : How to Change Parameters of Setup Codes Using the T able of Setup Codes on the following pages as a guide, follow the instructions below on how to change any of the factory defaults. Remember -All changes must be downloaded and saved into permanent memory for the changes to take effect the next time the system is turned on.
32 33 T able of Setup Codes and V alues of the Parameters NA VIGA TION FUNCTION CODES Description Code V alues of the Parameters Factory Defaults Navigation Gain 15 1 lowest gain, 73 highest gain 50 N.
34 35 T able of Setup Codes and Parameters FINE TUNING CODES Description Code V alues of the Parameters Factory Defaults Acceleration Limiter 5 1 lowest accel, 100 Highest accel 39 Code 5: This parameter limits the aggressiveness of the autopilot controlled turns.
34 35 T able of Setup Codes and Parameters HYDRAULIC CODES Description Code V alues of the Parameters Factory Defaults Helm Displacement 269 .1 to 6 by .1’ s 1.7 Pump Displacement 169 [Up Arrow] for 4 liter , [Down Arrow] for 2 liter 2 liter T urns Lock to Lock 26 .
36 37 GPS Manufacturer Model From GPS T o Autopilot NMEA In #1 T o Autopilot NMEA In #2 NMEA Out Radar Overlay Furuno 1850-D/F/DF White ( + ) Black ( - ) Y ellow ( + ) White ( - ) Blue ( + ) Brown ( -.
36 37 GPS Manufacturer Model From GPS T o Autopilot NMEA In #1 T o Autopilot NMEA In #2 NMEA Out Radar Overlay Red ( + ) Black ( - ) Garmin GPS Map 238 GPS Map 188 NMEA Out, Com 1 tx Blue ( + ) Black .
38 39 GPS Manufacturer Model From GPS T o Autopilot NMEA In #1 T o Autopilot NMEA In #2 NMEA Out Radar Overlay Red ( + ) Black ( - ) Lowrance LMS 332/337 Y ellow ( + ) Bare Grnd W ire ( - ) Must have V ersion 1.
38 39 RayMarine C Series E Series Y ellow ( + ) Brown ( - ) Y ellow ( + ) White ( - ) Blue ( + ) Brown ( - ) White ( + ) Green ( - ) GPS Manufacturer Model From GPS T o Autopilot NMEA In #1 T o Autopi.
40 41 Chapter II Installation of Wir eless Remote ................ This chapter will provide detailed information to accurately and successfully install the TR-1 Gladiator W ireless Remote Unit.
40 41 Item Description Part # Qty . 1 W ireless keypad transmitter 120-2420-02 2 2 Neck Lanyard 305-2401-00 1 3 Antenna Antenna Base #4-40 x 3/8 Php Screw 240-2452-00 340-2451-00 310-0072-03 1 1 1 4 R.
42 43 Item Description Part # Qty . 1 W ireless keypad transmitter 120-2420-00 2 2 Neck Lanyard 305-2401-00 1 3 Antenna Antenna Base #4-40 x 3/8 Php Screw 240-2452-00 340-2451-00 310-0072-03 1 1 1 4 R.
42 43 Thank Y ou Thank Y ou for the purchase of your TR-1 Gladiator wireless remote. TR-1 wireless remote has been designed to give shermen that competitive edge in shing and unparalleled precision and control of their boat. TR-1 Autopilots is dedicated to create the nest controls and guidance systems for the best in boating and shing.
44 45 Thank you for purchasing this accessory for your TR-1 Autopilot. Please read and understand this manual before installing and operating this system. The TR-1 wireless remote control is an add on system that provides the two most often used functions of the standard TR-1 wired remote in a compact wireless form.
44 45 The Five Button wireless remote control is an add on system that provides the ve most often used functions of the standard TR-1 W ired Remote in a compact wireless form.
46 47 When installing the wireless remote system: 1) Mount the receiver box and antenna away from sources of electronic interference such as the autopilot hydraulic pump and the engines ignition systems. 1. Mount the receiver box. Use the screws provided, or use wire ties.
46 47 Each keypad transmitter transmits its own unique identication code when a button is pressed. The receiver computer must be programmed to recognize your transmitter .
48 Limited Warranty This TR-1 product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, TR-1 will, at its sole option, repair or replace any components that fail in normal use.
Ein wichtiger Punkt beim Kauf des Geräts Garmin TR-1 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Garmin TR-1 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Garmin TR-1 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Garmin TR-1 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Garmin TR-1 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Garmin TR-1 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Garmin TR-1 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Garmin TR-1. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Garmin TR-1 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
