Benutzeranleitung / Produktwartung 1999 Contour des Produzenten Ford
Zur Seite of 244
1 Contents Before driving Introduction 2 Instrumentation 4 Controls and features 20 Seating and safety restraints 72 Starting and driving Starting 104 Driving 1 12 Roadside emergencies 137 Servicing Maintenance and care 158 Capacities and specifications 217 Customer assistance 223 Reporting safety defects (U.
Introduction 2 ICONS Indicates a warning. Read the following section on W arnings for a full explanation. Indicates that vehicle information related to recycling and other environmental concerns will follow . W e must all play our part in protecting the environment.
Introduction 3 INFORMA TION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. If possible, you should avoid hard braking for the first 1 600 km (1 000 miles).
Instrumentation Page 55 T urn signal/high beam Page 6 Instrument cluster Page 54 Hazard flasher control Page 56 W indshield wiper/washer control Page 162 Hood release Page 20, 21 Headlamp control/ Fog.
5 Instrumentation Page 23 Instrument panel dimmer switch On various models, the appearance and location of some items may differ from those shown here.
Instrumentation 6 T urn signal Flashes when the left or right turn signal or hazard lights are activated. There are two different instrument cluster designs.
Instrumentation 7 High beams Illuminates when the headlamp high beams are on. Charging system Briefly illuminates when the ignition is turned on and the engine is off. The light also illuminates when the battery is not charging properly and the vehicle may require electrical system service.
Instrumentation 8 T raction control system light (if equipped) This light comes on when the traction control system has been disengaged. It may flash on and off while driving to indicate the system is operating.
Instrumentation 9 O/D Off indicator (Automatic transaxle only) Illuminates and remains illuminated when the transaxle control switch (TCS) on the side of the gearshift lever is pressed and overdrive is turned off. For details, refer to the Driving chapter .
Instrumentation 10 Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics (OBD II) system. This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Instrumentation 11 The check engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’ s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Instrumentation 12 These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly tightening the fuel cap. After three drive cycles without these or any other temporary malfunctions present, the check engine light should turn off.
Instrumentation 13 CHECK ENGINE Air bag readiness Briefly illuminates when the ignition is turned on. If the light fails to illuminate, continues to flash, or remains on, have the system serviced immediately . Low fuel Illuminates when the fuel tank has approximately eight liters (two gallons) remaining.
Instrumentation 14 Brake system warning Extinguishes when the parking brake is released. Illuminates after releasing the parking brake to indicate low brake fluid level. Illumination while driving may indicate that one of the braking circuits has failed.
Instrumentation 15 Anti-lock brake system (ABS) (if equipped) Momentarily illuminates when the ignition is turned on and the engine is off. If the light stays on or continues to flash, the ABS needs to be serviced.
Instrumentation 16 EF BRAKE O/D OFF 0001 23 0 0 0 0 10 20 30 40 50 60 70 80 90 11 0 12 0 13 0 MPH 20 40 60 55 80 120 10 0 140 160 18 0 200 10 0 CHECK ENGINE TRACTION CONTROL CH 0001 23 0 0 0 0 10 20 3.
Instrumentation 17 Headlamps on warning chime Sounds when the headlamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is open. T esting the warning and indicator lights and chimes T urn the ignition key to the on position without starting the engine.
Instrumentation 18 CH Engine coolant temperature gauge Indicates the temperature of the engine coolant. If it enters the red section, the engine is overheating. Switch off the ignition and determine the source of the problem. Refer to Checking and adding engine coolant in the Maintenance and care chapter .
Instrumentation 19 Speedometer Indicates the current vehicle speed. Odometer Registers the total mileage of the vehicle. T rip odometer The trip odometer can register the mileage of individual journeys.
Controls and features 20 M I R R O R S OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90.
Controls and features 21 Daytime running lights (DRL) (Canadian vehicles only) The DRL system turns on the highbeam headlamps, with a reduced light output, when: • the vehicle is running and the ignition is in the on position and • the headlamp system is in the off position.
Controls and features 22 Rear window defroster (if equipped) Press the defroster control to clear the rear window of thin ice and fog. The ignition must be in the on position to operate the rear window defroster . The defroster turns off automatically after 10 minutes or when the ignition is turned to the off position.
Controls and features 23 Panel dimmer control Adjust the control to vary the intensity of the panel lighting. Operates only when the exterior lights are switched on. T o switch on the interior lamp, rotate the control completely to the left. Power mirrors (if equipped) The control can be swivelled and turned.
Controls and features 24 Climate control system V ents Airflow from the vents may be adjusted by moving the horizontal control or vertically adjusting the vent (except passenger side outer vent) according to your airflow preference.
Controls and features 25 Heater only system (if equipped) OFF LO PNL/FLR PANEL FLOOR DEF FLR DEF HI / LO HI T emperature control knob Controls the temperature of the airflow inside the vehicle. On heater -only systems, the air cannot be cooled below the outside temperature.
Controls and features 26 • FLR/DEF – Distributes outside air through the floor ducts and the windshield defroster ducts. • DEF – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield.
Controls and features 27 Manual heating and air conditioning system (if equipped) OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / LO HI Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle.
Controls and features 28 Under normal conditions, your vehicle’ s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct.
Controls and features 29 • PNL/FLR – Distributes outside air through the instrument panel registers and the floor ducts. However , the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode.
Controls and features 30 • DEF – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher , the air conditioner will automatically dehumidify the air to prevent fogging.
Controls and features 31 Cabin air filter Y our vehicle is equipped with an air filter that removes pollen and road dust from outside air before it is directed to the interior of the vehicle. Refer to the Maintenance and care chapter for maintenance of this filter .
Controls and features 32 OFF LO PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C HI / POWER AUDIO AM/FM SCAN SEEK 3 1 2 4 5 ANS SIDE 1-2 EJECT VOLUME 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 .
Controls and features 33 Electronic stereo radio with cassette Electronic stereo radio 13CCfen 3/25/99 1:50 PM Page 33.
Controls and features 34 SIDE 1-2 13CCfen 3/25/99 1:50 PM Page 34.
Controls and features 35 SIDE 1-2 1-2 SIDE 13CCfen 3/25/99 1:50 PM Page 35.
Controls and features 36 Power control Press the control to turn the audio system on or off. V olume control Press the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features 37 The tune adjust with electronic stereo radio • Press (–) to move to the next frequency down the band (whether or not a listenable station is located there).
Controls and features 38 • W ithin approximately five seconds, press and release either or on the SEEK control to change to the next frequency up or down. • Press and hold down or to quickly move through the frequencies. Seek function The seek function control works in radio or tape mode.
Controls and features 39 Scan function The scan function works in radio and CD mode (if equipped). Scan function with electronic stereo cassette radio Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode.
Controls and features 40 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Controls and features 41 2. Press the AUTO PRESET control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
• Press (+) or (–) on the volume control to increase or decrease treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Controls and features 42 T reble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output.
Controls and features 43 Speaker fade adjust Speaker sound distribution can be adjusted between the front and rear speakers. • Push the AUDIO control repeatedly until the display reads F ADE. • Press the (+) side of the volume control to shift sound to the front speakers.
Setting the clock Press and hold CLOCK, then press SEEK to increase the hours or to increase minutes. The clock will display 12-hour time with no AM/PM indications. On the single CD audio system, the clock can be set with the radio power on or off. Controls and features 44 T ape play select Insert a tape to begin tape play .
Controls and features 45 Rewind/fast forward in CD mode • Press the control for less than three seconds for slow rewind. • Press the control for more than three seconds for fast rewind. • Press the control for less than three seconds for slow forward action.
Controls and features 46 CD eject Press the control to stop and eject a CD. If a disc is ejected from the CD player but is not removed within approximately 10 seconds, the player will automatically re.
Controls and features 47 DISPLA Y SCREEN The display screen gives information on the status of the audio system. Display Information AM, FM1 or FM2 Indicates which frequency band the audio system is in 87.
Controls and features 48 T roubleshooting the CD Player The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • Y ou may be travelling on a rough road, playing scratched discs or the disc may be dirty .
Controls and features 49 CD and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not insert more than one disc at a time. • Do not expose discs to direct sunlight or heat sources for extended periods of time.
Controls and features 50 • Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when not being played.
Controls and features 51 • T errain. Hills, mountains and tall buildings between your vehicle’ s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms.
Controls and features 52 STEERING COLUMN CONTROLS Ignition 1. Ignition off, steering wheel locked. On vehicles with automatic transaxles, the ignition key can return to this position only if the gearshift lever is in P (Park). 2. The accessory position.
Controls and features 53 Tilt steering Pull the locking lever on the steering column cover up to adjust the steering column position. Secure the wheel by releasing the lever thereby allowing the lever to return to the lock position. Never adjust the steering wheel while the vehicle is moving.
Controls and features 54 Hazard flasher control Use only in an emergency to warn traffic of vehicle breakdown or approaching danger . Depress to activate. Depress again to switch off. The hazard lights can be operated when the ignition is off. Horn Press the pad.
Controls and features 55 Multi-function switch The turn signal functions are available only with the ignition switch on. Right turn signal Move the lever up.
Controls and features 56 Wipers Lift the windshield wiper lever to the desired speed interval. • Intermittent: push lever up to the first position. • Low: push lever up to the second position. • High: push lever up to the third position. For a single wipe, push the lever downward.
Controls and features 57 Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Off On Speed control (if equipped) T o turn speed control off • Press Off, or • turn off the vehicle ignition. Once the speed control is switched off, the previously programmed set speed will be erased.
Controls and features 58 T o set a speed Press Set Acc. For speed control to operate, the speed control must be on and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Controls and features 59 Res Set Acc Coast T o set a lower speed • Press and hold Coast. Release the control when the desired vehicle speed is reached, or • press and release Coast. Each press will decrease the set speed by 1.6 km/h (1 mph), or • depress the brake pedal.
Controls and features 60 Res Set Acc Coast T o return to a set speed • Press Res. For Res to operate, the vehicle speed must be faster than 48 km/h (30 mph). T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.
Controls and features 61 12 SEC On Off 12 SEC Interior lamps (sunroof equipped vehicles) The reading lamps are operated by separate on/off switches and can be adjusted to point in the desired direction. Open/Lift Close Sunroof (if equipped) The electric sunroof can be operated only when the ignition is switched on.
Controls and features 62 Power door locks (if equipped) Push to lock or unlock all doors. Power windows (if equipped) The windows will only operate when the ignition is switched on. Press the appropriate control to operate the power windows at each door position.
Controls and features 63 Safety switch Move the switch to the left to prevent passengers from operating the windows. Move the switch to the right to allow passengers to operate the windows. CHILD LOCK BELOW SECURITE ENFANTS CI-DESSOUS ´ VERROUILLEE , LOCKED WHEN LOCKED, DOOR WON`T OPEN FROM INSIDE.
Controls and features 64 PULL Remote luggage compartment control Pull the control located on the left of the driver seat to open the luggage compartment. FLOOR MOUNTED CONTROLS Parking brake For information on the parking brake, refer to Preparing to start the vehicle in the Starting chapter .
Controls and features 65 Fuel pump shut-off switch For information on the fuel pump shut-off switch, refer to Fuel pump shut-off switch in the Roadside emergencies chapter .
Controls and features 66 TRUNK UN LOCK PANIC LOCK REMOTE KEYLESS ENTR Y SYSTEM (if equipped) If your vehicle has a remote entry system, you can lock and unlock the vehicle doors and open the luggage compartment without using a key . The remote also has a personal alarm feature.
Controls and features 67 Opening the luggage compartment Press the TRUNK control. Sounding the panic alarm Press the P ANIC control. The horn will sound and the headlamps and tail lamps will flash for approximately 2 minutes and 45 seconds. T o deactivate the alarm, press the P ANIC control again or turn the ignition key to the on position.
Controls and features 68 Replacing lost transmitters T ake your transmitters to the dealer for reprogramming if: • a transmitter is lost, or • you want to purchase additional transmitters.
Controls and features 69 P ASSIVE ANTI-THEFT SYSTEM (if equipped) The Passive Anti-Theft System (P A TS) is an engine immobilization system. It is an additional theft protection feature that prevents the engine from being started unless a coded key is used.
Controls and features 70 Functional check When the ignition is switched on, the control light will illuminate for approximately three seconds to indicate that the system is operating correctly . If the control light flashes rapidly for approximately one minute and then repeatedly at irregular intervals, the system did not recognize the key code.
Controls and features 71 Spare key programming A maximum of 8 keys in all can be coded with any two coded keys. • Insert the first key in the ignition switch and turn to position 3. • T urn the key back to position 1 and remove from the ignition switch within 5 seconds.
Seating and safety restraints 72 Adjusting the head restraints Push or pull the head restraint to the desired height. SEA TING Manually adjusting the seats Pull the lever located at the front edge of the seat to move the seat forward or backward. Reclining the seats Pull the lever on the outside of the seat to recline the seat.
Seating and safety restraints 73 Adjusting the power seats (if equipped) Move the relevant control in the respective direction to adjust the seat as follows: 1 2 3 4 Seat (1) Forward and backward (2) .
Seating and safety restraints 74 Folding rear seats (if equipped) Pull the release knob located in the luggage compartment. Fold down the seat. The seat back cannot be released while the built-in child seat (if equipped) is open.
Seating and safety restraints 75 Important safety restraints precautions The use of safety belts helps to restrain both driver and passenger in case of a collision. In most states and Canada, the law requires the use of safety belts. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints 76 Combination lap and shoulder belt Insert the tongue into the slot in the buckle to fasten. Push the red release button and remove the tongue from the slot to unfasten. The passenger safety restraints in the vehicle are combination lap and shoulder belts.
Seating and safety restraints 77 Automatic locking mode In this mode, the shoulder belt is automatically prelocked; however , the belt will react to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver’ s safety belt.
Seating and safety restraints 78 Using automatic locking mode The automatic locking mode must be used when installing a child safety seat in any passenger seat. 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder belt portion and pull downward until the entire belt is extracted.
Seating and safety restraints 79 Front seat safety belt height adjustment T o lower the height of the shoulder belt: 1. Push the control down. 2. Slide down. T o raise the height of the shoulder belt: 1. Slide up. 2. Pull down on the height adjuster to make sure that it is locked in place.
Seating and safety restraints 80 Safety belt indicator light and warning chime Illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
Seating and safety restraints 81 Conditions of operation If the driver safety belt is not buckled before the ignition key is turned to on, the safety belt indicator illuminates for 1-2 minutes and the warning chime sounds for 4-8 seconds.
Seating and safety restraints 82 Care of safety belts Periodically check the belts for damage or fraying. Check the security of the anchorage points and the locking action of the inertia reels by giving each belt a sharp tug.
Seating and safety restraints 83 Important supplemental restraint system (SRS) precautions The supplemental restraint system (SRS) is designed to: • work with the safety belt to protect the driver and right front passenger . • reduce certain upper body injuries.
Seating and safety restraints 84 Do not attempt to service, repair , or modify the air bag Supplemental Restraint System (SRS) or its fuses. See your Ford or Lincoln-Mercury dealer . When installing forward- facing child seats in the front seat, always move the passenger seat as far back from the instrument panel as possible.
Seating and safety restraints 85 How does the air bag supplemental restraint system (SRS) work? The SRS is designed to activate when the vehicle is in a collision, similar to hitting a fixed barrier head-on at 12-24 km/h (8-14 mph). The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
Seating and safety restraints 86 If the air bag is inflated, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints 87 Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a secondary warning light to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter .
Seating and safety restraints 88 Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or a qualified technician.
Seating and safety restraints 89 Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Do not leave children, unreliable adults, or pets unattended in your vehicle.
Seating and safety restraints 90 Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are 4 years old or younger and who weigh 18 kg [40 lb] or less), you must put them in safety seats made especially for children.
Seating and safety restraints 91 Children and safety belts Children who are too large for child safety seats (as specified by the child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraints and air bag precautions that apply to adult passengers in your vehicle.
Seating and safety restraints 92 T o improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt- positioning booster seat that is labelled as conforming to all federal motor vehicle safety standards.
Seating and safety restraints 93 Built-in child safety seat (if equipped) The rear seat may include a built-in child seat. This child seat conforms to all federal and local motor vehicle safety standards. Read the labels located on the child seat cushion and shoulder belt for information on the built-in child seat.
Seating and safety restraints 94 Child seat interlock safety feature The interlock ensures that a child is not placed in the integrated child seat when the folding seatback is not securely latched. It prevents the seatback from being unlatched while the child seat is in use.
Seating and safety restraints 95 1. Make sure that the seatback is securely latched in place. 2. Grasp the child seat cushion and pull the top forward to release the latch. Continue to unfold the child seat until it rests on the seat in the fully open position.
Seating and safety restraints 96 4. If connected, squeeze the tabs on the top and bottom of the chest clip and pull the halves apart to open the chest clip. Then release the lower half of belt by pressing the red button. 5. Place the child in the child seat and position the shoulder belts over each shoulder .
Seating and safety restraints 97 7. Fasten both halves of the chest clip below the child’ s shoulders and adjust it to comfortably hold the shoulder belts in place on the child’ s chest. The color green must appear in the indicator window when fastened.
Seating and safety restraints 98 T o stow the built-in child seat Return the child seat cushion to the upright position, then press firmly in the center and top of the child seat. Removing your child from the built-in child seat 1. Squeeze the tabs on the top and the bottom of the chest clip and pull the halves apart to open the chest clip.
Seating and safety restraints 99 Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or collision.
Seating and safety restraints 100 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
Seating and safety restraints 101 5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage.
Seating and safety restraints 102 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place.
Seating and safety restraints 103 T o install a tether from a child safety seat in the front seat, route the tether strap under the vehicle seat head restraint and hook the tether hook into the hole in the tongue of the center rear lap belt.
Starting 104 Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. IMPORT ANT SAFETY PRECAUTIONS A computer system controls the engine’ s idle revolutions per minute (rpm).
Starting 105 IMPORT ANT VENTILA TION INFORMA TION If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (1 inch). OFF PNL/FLR PANEL A/C FLOOR DEF FLR DEF MAX A/C / Adjust the heating or air conditioning to bring in fresh air .
Starting 106 Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves, and other debris. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects.
Starting 107 PREP ARING TO ST ART THE VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference- Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise.
Starting 108 If starting a vehicle with an automatic transaxle: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transaxle: • Make sure the parking brake is set. • Push the clutch pedal to the floor otherwise the engine will not crank (turn over).
Starting 109 3. T urn the key to the on position (without turning the key to start). Make sure the following lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced by your dealer or a qualified service technician.
Starting 110 ST ARTING THE ENGINE 1. T urn the key to the start position (4) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to the on (3) position. 3 4 2 1 2. If the engine does not start within five seconds, wait ten seconds and try again.
Starting 111 USING THE ENGINE BLOCK HEA TER (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater - defroster system to respond quickly . It is strongly recommended if you live in a region where temperatures reach –23°C (–10°F) or below .
112 Driving BRAKES Y our brakes are self-adjusting. Refer to the “Scheduled Maintenance Guide” for maintenance intervals. Anti-lock braking system (ABS) (if equipped) The ABS operates by detecting the onset of wheel lock-up during brake applications and compensating for this tendency .
Driving 113 T wo important rules when braking in emergencies with ABS: 1. Apply full force on both brake and clutch pedal (if equipped). Braking with ABS • In an emergency , apply full force on the brake pedal. In vehicles with manual transaxles, you must also depress the clutch pedal.
Driving 114 Parking brake T o engage the parking brake: Pull the handle upward. T o release the parking brake: 1. Press and hold the release button. 2.
Driving 115 TRACTION CONTROL (if equipped) This system prevents wheel spin at all speeds. The control will toggle this function on and off, but the feature defaults to on after each cycle of the ignition key .
Driving 116 STEERING YOUR VEHICLE Y our vehicle comes with power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle at a constant vehicle speed, have the power steering system checked.
Driving 117 TRANSAXLE OPERA TION Automatic transaxle (if equipped) V ehicles equipped with an automatic transaxle are equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from the P (Park) position unless the brake pedal is depressed.
Driving 118 5. Push and hold the thumb button and move the gearshift. 6. Remove the screwdriver when the gearshift moves from the P (Park) position. Overriding the brake-shift interlock feature If it .
Driving 119 The console-mounted gearshift will lock when you turn the key to the lock position. When the gearshift is in any position except P (Park), the ignition key cannot be turned to lock or removed from the steering column. T o remove the key , the gearshift lever must be in P (Park).
Driving 120 • D (Overdrive) Note that the vehicle’ s gearshift is console-mounted on the floor . The transaxle control switch (TCS) is located on the gearshift handle. The transaxle control indicator light (O/D light) is located on the instrument panel.
Driving 121 • D (Drive) D (Drive) provides more engine braking than overdrive and is useful when driving through hilly terrain or if your vehicle requires additional power for climbing hills. Activate by pressing the transaxle control switch (TCS) located on the gearshift handle.
Driving 122 • 1 (First) Use the 1 (First) position to provide maximum engine braking on steep downgrades. Upshifts will not occur while the gearshift lever remains in the 1 (First) position. Upshifts may be made by shifting to the 2 (second) position or to D (Drive).
Driving 123 Manual transaxle (if equipped) V ehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. Using the clutch When starting a vehicle with a manual transaxle: 1.
Driving 124 22 Recommended shift speeds 2.0 litre engine 5-speed transaxle shift speed schedules Recommended upshifts: Shift from km/h mph 14 25 33 48 40 53 77 mph 12 20 29 40 km/h 19 32 64 First to second Second to third Third to fourth Fourth to fifth During acceleration: During cruise*: 46 2.
Driving 125 Parking 1. Apply the brake and the clutch and shift into neutral. 2. Engage the parking brake. 3. Shift into 1 (First) or R (Reverse). 4. T urn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone.
Driving 126 GVW (Gross V ehicle Weight) Base curb weight plus the payload weight. The GVW is not a limit or a specification. Payload Combined maximum allowable weight of passengers, cargo, and optional equipment. LOADING YOUR VEHICLE Before loading your vehicle, familiarize yourself with these terms.
Driving 127 GCW (Gross Combined Weight) The GCW is the maximum combined weight of the towing vehicle (including passengers and cargo) and the loaded trailer . The GCW is specified by the manufacturer to indicate the combined maximum loaded weight that the vehicle is designed to tow .
Driving 128 Payload = GVWR minus Base curb weight T o obtain the correct weight for your vehicle, try taking your vehicle to a shipping company or an inspection station for trucks. Do not use replacement tires with lower weight capacities than the originals because they might lower the vehicle’ s GVWR and GA WR.
Driving 129 It is extremly dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Driving 130 TRAILER TOWING Y our vehicle is capable of towing a trailer of up to a maximum of 454 kg (1 000 lbs) gross trailer weight with a maximum tongue load of 45 kg (100 lbs). It should also have 2.3 sq. meters (25 sq. feet) or less frontal area.
Driving 131 Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’ s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing.
Driving 132 Preparing to tow Use the proper equipment for towing a trailer and make sure that it is properly attached to your vehicle. See your dealer or a reliable trailer retailer if you require assistance.
Driving 133 Using a hitch Do not use hitches that: • Clamp onto the vehicle bumper . • Attach to the axle. Distribute the load so that only 10 to 15% of the total weight of the trailer is on the tongue. T ie down the load so that it does not shift and change weight on the hitch.
Driving 134 Using trailer brakes Use electric brakes or manual, automatic or surge type hydraulic brakes that meet federal and local regulations. Install and adjust brakes according to the manufacturer’ s instructions. Using safety chains Always connect the trailer’ s safety chains to the vehicle.
Driving 135 Driving while towing a trailer Do not drive faster than 72 km/h (45 mph) while towing a 454 kg (1 000 lb) trailer . Do not drive faster than 72 km/h (45 mph) with any weight trailer while towing in hilly terrain or on hot days. Speed control (if equipped) may not work properly while towing on long, steep grades.
Driving 136 FUEL CONSUMPTION Fuel economy can be improved by avoiding: • lack of regular , scheduled maintenance, • excessive speed, • rapid acceleration, • driving with the brake pedal depres.
Roadside emergencies 137 HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown or approaching danger . Depress to activate.
138 Roadside emergencies If your engine cranks but does not start after a collision or substantial jolt: 1. T urn the ignition key to the off position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button down.
Roadside emergencies 139 Even after a fuse is replaced, it will continue to blow if the cause of the overload is not identified and corrected. If the fuse continues to blow , have the vehicle’ s electrical system checked by your dealer or a qualified service technician.
Roadside emergencies 140 1 11 12 13 14 15 16 R6 R5 R4 R3 R2 10 123 45 6 7 8 9 R1 R7 R8 R9 R10 R11 D1 D2 17 18 46 47 48 49 50 51 52 39 40 41 42 43 44 45 Power distribution box T o check or replace a fuse or a relay , remove the cover of the fuse box in the engine compartment by releasing the latch (1) and lifting up.
Roadside emergencies 141 Ampere rating Circuits protected 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 39 40 41 42 43 44 45 46 47 48 49 50 51 52 — 7.
Roadside emergencies 142 Power distribution box (engine compartment) Relay Circuits switched R 1 R 2 R 3 R 4 R 5 R 6 R 7 R 8 R 9 R 10 R 11 D1 D2 Passenger compartment fuse panel T o check or change a fuse or a relay , open the fuse box by pulling down the lock release lever (1).
Roadside emergencies 143 A blown fuse can be identified by a break in the wire. All fuses are a push fit. Five reserve fuses with different current ratings are attached to the inside cover of the power distribution box in case of emergency fuse replacement.
Roadside emergencies 144 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 — C10 40 7.5 15 15 20 7.5 15 30 30 7.5 7.5 7.5 7.5 7.5 7.5 — 30 — Not used W iper motors (circuit breaker) Po.
Roadside emergencies 145 Fuse rating 7.5 amp 10 amp 15 amp 20 amp 30 amp 30 amp fuse link 40 amp 60 amp fuse link 80 amp fuse link 100 amp fuse link Color brown red light blue yellow light green pink .
Roadside emergencies 146 CHANGING TIRES Park your vehicle in such a position that neither the traffic nor you are hindered or endangered when changing the tire. Ensure that the vehicle is on firm, level ground. Secure your vehicle further by blocking the wheels.
Roadside emergencies 147 80 MAX km/h When driving with a temporary spare tire: • Do not exceed the maximum speed of 80 km/h (50 mph) and only drive the shortest possible distance. • Do not exceed the permissible gross weight of the vehicle. • Do not install more than one spare wheel on your vehicle at any one time.
Roadside emergencies 148 Removing a tire 1. Apply the parking brake and 1 (first) gear (manual transaxle) or the P (Park) position (automatic transaxle). 2. Activate the hazard flashers. 3. The driver and all passengers must leave the vehicle. 4. Secure the vehicle against rolling or sliding.
Roadside emergencies 149 Replacing a tire 1. Push the spare tire onto the wheel studs. 2. Screw on the wheel nuts, ensuring the tapered end of the wheel nuts are facing the wheel, and secure in a clockwise direction. 3. Lower the vehicle and remove the jack by turning the handle counterclockwise.
Roadside emergencies 150 JUMP ST ARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter .
Roadside emergencies 151 3. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables.
Roadside emergencies 152 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
Roadside emergencies 153 Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery .
Roadside emergencies 154 Jump starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables.
Roadside emergencies 155 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
Roadside emergencies 156 If towing is necessary , it is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T -hook or slingbelt towing procedure.
Roadside emergencies 157 Never use a tow bar that attaches to the bumper when you tow your vehicle. This could damage the bumper and cause an accident.
Maintenance and care 158 SERVICE RECOMMENDA TIONS • W e highlight do-it-yourself items in the engine compartment for easy location. • As possible, we design parts that can be replaced without tools. • W e provide you with a maintenance guide and or service guide which makes tracking routine service for your vehicle easy .
Maintenance and care 159 Precautions when servicing your vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: • Do not work on a hot engine. The cooling fan is automatic and may come on at any time.
Maintenance and care 160 Working with engine off (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly .
Maintenance and care 161 Working with engine on (automatic transaxle) 1. Set the parking brake fully and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly . Do not start your engine with the air cleaner removed and do not remove it while the engine is running.
Maintenance and care 162 Opening the hood • Pull the handle (1) located under the instrument panel. 000123 0 0 0 0 10 20 30 40 50 60 70 80 90 10 0 110 120 130 MPH 20 40 60 55 80 120 100 140 160 180 .
Maintenance and care 163 For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black. 2.0 litre EFI-engine compartment Power steering reservoir Engine coolant reser.
Maintenance and care 164 Power steering reservoir Engine coolant reservoir 2.5 litre EFI-engine compartment For ease of identification, all filler caps and the engine oil dipstick are marked yellow/black.
Maintenance and care 165 ADD FULL Engine oil Use SAE 5W -30 motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by Ford W arranty .
Maintenance and care 166 6. If the oil level is below the minimum line, add engine oil as necessary . If the oil level is beyond the maximum line, engine damage or high oil consumption may occur and some oil must be removed from the engine by a service technician.
Maintenance and care 167 Refer to the maintenance guide and or service guide for additional information. Always dispose of used automotive fluids in a responsible manner . Follow your community’ s standards for disposing of these types of fluids. Call your local recycling center to find out more about recycling automotive fluids.
Maintenance and care 168 Brake/clutch fluid reservoir Brake and clutch fluid systems are supplied from the same reservoir . The level of the fluid must lie between the MIN and MAX marks on the side of the reservoir . If the level falls below the MIN mark, the brake fluid level warning light on the instrument cluster will illuminate.
Maintenance and care 169 Engine coolant maintenance MAX MIN Checking and adding engine coolant Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter .
Maintenance and care 170 When adding engine coolant Ford recommends Ford Premium Cooling System Fluid, which is an optimized formula that will protect all metals and rubber elastomers used in Ford engines for four years or 80 000 km (50 000 miles).
Maintenance and care 171 Always dispose of used automotive fluids in a responsible manner . Follow your community’ s standards for recycling and disposing of automotive fluids. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes.
Maintenance and care 172 MAX MIN Adding engine coolant 1. Before removing the engine coolant recovery cap, turn the engine off and allow it to cool. 2. When the engine is cool, turn and remove the cap. Never remove the coolant recovery cap while the engine is running or hot.
Maintenance and care 173 Checking and adding power steering fluid Switch off the engine. W ith the steering system at normal operating temperature, the fluid level should come up to the MAX mark. If the fluid level drops below the MIN mark, add the specified fluid.
Maintenance and care 174 Automatic transaxle fluid Follow the scheduled service intervals outlined in the maintenance guide and or service guide. Before adding any fluid, make sure the correct type is used.
Maintenance and care 175 The transaxle fluid should be in this range if at normal operating temperature 66°C - 77°C (150°F - 170°F). The transaxle fluid should be in this range if at room temperature 10°C - 35°C (50°F - 95°F).
Maintenance and care 176 Battery Y our vehicle may be equipped with a Motorcraft maintenance-free battery . The Motorcraft maintenance-free battery normally does not require additional water during its life of service.
Maintenance and care 177 Battery replacement If your original equipment battery requires replacement while under warranty , it will be replaced with a Motorcraft service battery , identical in design technology .
Maintenance and care 178 Batteries normally produce explosive gases which can cause personal injury . Do not allow flames, sparks or lit tobacco to come near the battery . Always cover your face and protect your eyes and also provide ventilation. Applying too much pressure on the ends when lifting a battery could cause acid to spill.
Maintenance and care 179 Relearning the idle function Because your vehicle’ s engine is electronically controlled, some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the computer must “relearn” its idle conditions before your vehicle can drive properly .
Maintenance and care 180 Checking wiper blades Check the wiper blades on your vehicle for roughness by running the tips of your fingers over the edge of the blade. T races of grease, silicone and fuel prevent wiper blades from functioning properly . W e recommend Ford cleaning solutions or equivalent to clean wiper blades.
Maintenance and care 181 2. Remove the plastic caps from the screws on the grille. Remove the screws. 3. Open the hood. Pull off the rubber weatherstrip at the back of the engine compartment. Remove the screws that hold the grille, separate the two halves and remove the grille.
Maintenance and care 182 New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These Tire Quality Grades are determined by standards that the United States Department of T ransportation has set.
Maintenance and care 183 T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and care 184 T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and care 185 Checking tire pressure Check the tire pressure periodically after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). Inflate the tires as necessary . T o check the tire pressure, insert the tire pressure gauge into the valve.
Maintenance and care 186 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over . Replacing tires Replace tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias- belted, or bias-type tires.
Maintenance and care 187 Dispose of worn tires in accordance with local environmental regulations. Refer to the Safety Compliance Certification label to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle.
Maintenance and care 188 The tires on your vehicle have all- weather treads to provide traction in rain and snow . However , in some climates, using snow tires and chains may be necessary . Ford offers snow chains as a Ford approved accessory and recommends use of these or their equivalents on approved tires.
Maintenance and care 189 Change over from winter to summer tires as soon as road conditions allow , this will reduce fuel consumption and noise in the vehicle’ s interior . • Drive cautiously . If you hear the chains rub or bang against the vehicle, stop and retighten them.
Maintenance and care 190 Automotive fuels can cause serious injury or death if misused or mishandled. IMPORT ANT FUEL INFORMA TON Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
Maintenance and care 191 Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Make sure the fuel cap is correctly fitted after fueling.
Maintenance and care 192 Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty . Y our vehicle was not designed to use fuel containing manganese- based additives such as MMT .
Maintenance and care 193 Octane recommendations Y our vehicle is designed to use regular gasoline with an (R+M)/2 octane rating of 87. W e do not recommend gasolines labeled as “regular” in high altitude areas that are sold with octane ratings of 86 or even less.
Maintenance and care 194 The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise fuel may spray out and injure you or others.
Maintenance and care 195 Calculating fuel economy T o accurately calculate your vehicle’ s fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in litres or gallons).
Maintenance and care 196 EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and care 197 BRAKE O/D OFF TRACTION CONTROL Alternative design Alternative design W atch for fluid leaks, strange odors, smoke, loss of oil pressure, engine overheating, illumination of the charging system warning light or the check engine warning light.
Maintenance and care 198 Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Maintenance and care 199 If the vehicle’ s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test“ condition.
Maintenance and care 200 The bulbs for the low beam, high beam, turn signals and side lamps are housed in the lamp assembly . T o replace a bulb, the complete lamp assembly has to be removed as follows: 1. Switch off the lamps. 2. Open the hood. 3. Remove the lower screw (2) from the headlamp housing.
Maintenance and care 201 Reinstalling the headlamp assembly The gasket lining must be seated properly around the lamp assembly when reinstalling. All bulb connectors must be correctly connected. Install in the reverse order . Headlamps – low beam Disconnect the electrical connector and replace the bulb.
Maintenance and care 202 Foglamps (if equipped) 1. T urn the bulb counterclockwise and pull it out of the light assembly . 2. Remove the electrical connector . 3. Fit the new bulb in reverse order (do not touch the glass part of the bulb). Front turn signal/side lamps Pull the socket out.
Maintenance and care 203 License plate lamp Pry out the light assembly with a flat-bladed screwdriver . Remove the bulb from the clip holder . Replace with the new bulb in reverse sequence. Brake/turn signal/tail lamps 1. Disconnect the electrical connector .
Maintenance and care 204 High-mounted brake lamp Enter the rear seat compartment. 1. Remove the high mounted stop lamp assembly . 2. Remove the red bulb cover . 3. Remove inoperative stop lamp bulb. T o install, fit the new bulb in reverse sequence. On vehicles equipped with a rear spoiler , the high-mounted brake lamp is included in the spoiler .
Maintenance and care 205 Interior lamps (sunroof equipped vehicles) Open the lamp assembly . The bulbs can be replaced after the contact plate has been hinged back. Interior lamps with reading lamps (if equipped) Remove the clip located on lens to access the center bulb.
Maintenance and care 206 Function T rade number 3457 NA 9005 9006 893 1157 1156 Front /turn lamp Headlamp (high) Headlamp (low) Foglamp/License plate lamp Rear tail/turn/brake lamp Backup lamp Bulb sp.
Maintenance and care 207 Aiming the headlamps Y our vehicle is equipped with a V ehicle Headlamp Aim Device (VHAD) on each headlamp body . Each headlamp may be properly aimed in the horizontal direction (left/right) and the vertical direction (up/down).
Maintenance and care 208 Adjusting the horizontal aim 1. Make sure the vehicle is on a level surface . 2.W ith the hood open, locate the horizontal indicator and adjusting screw .
Maintenance and care 209 Adjusting the vertical aim The numbers shown on the vial indicate beam direction in degrees up or down. 1. Make sure the vehicle is on level ground. 2. W ith the hood open, locate the bubble level vertical aim indicator , and adjusting screw .
Maintenance and care 210 W ashing your vehicle Only use car washing areas that have environmentally friendly drainage systems. VEHICLE CARE W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent.
Maintenance and care 211 W axing your vehicle The best way to determine when the paintwork needs waxing is by noting when water stops beading on the surface. This could be every three or four months depending on operating conditions. Use only carnauba or synthetic- based waxes.
Maintenance and care 212 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, paint repair foil or aerosol spray from the Ford accessories line. Observe the application instructions on the products.
Maintenance and care 213 Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup act as insulators and keep the engine warmer than normal. Follow these guidelines to clean your engine: • T ake care when using a power washer to clean the engine.
Maintenance and care 214 Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Clean with a tar remover if necessary . Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Maintenance and care 215 Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Follow the directions that come with the cleaner . Cleaning leather seats (if equipped) For routine cleaning, wipe the surface with a soft, damp cloth.
Maintenance and care 216 Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets and warm water . Do not bleach or dye the belts, because these actions may weaken the belt webbing.
217 Capacities and specifications * Refer to V ehicle Emission Control Information (VECI) decal for spark plug and gap specifications. ** If a spark plug is removed for examination, it must be reinstalled in the same cylinder .
Capacities and specifications 218 * T otal capacity ** with automatic transaxle Engine oil - with filter - without Manual transaxle 1.9 l (2.0 qts) Automatic transaxle with oil cooler Power steering Cooling system with heating W indshield washer fluid Fuel tank Braking system 4.
Lubricant Specifications Item Ford part name or equivalent High performance DOT 3 brake fluid, DOT 4 brake fluid or Super DOT 4 Premium engine coolant Motorcraft motor oil 5W -30 super premium MERCON .
Capacities and specifications 220 Engine data * Mechanical valve adjuster 2.0 litre Engine 2.5 litre Engine 1988 2544 96 (125) 5500 125 (170) 6250 176 (130) 4000 220 (162) 4250 6150 6700 6375 6925 800±50 (880±50) 725±50 (725±50) 1-3-4-2 1-4-2-5-3-6 1.
D A E B C Dimensions mm (inches) 4556 (179.4) 1751 (68.9) 1380 - 1427 (54.3 - 56.2) 2704 (106.5) 1499 - 1518* (59.0 - 59.8) 1483 - 1502* (58.4 - 59.1) A = Maximum length B = Overall width (without mir.
Capacities and specifications 222 VEHICLE IDENTIFICA TION NUMBER The vehicle identification number (VIN) is attached to a metal tag and is located on the front driver’ s side of the instrument panel. The VIN tag may be seen by looking through the windshield from the outside of the vehicle.
Customer assistance 223 GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern. Ford offers a complimentary roadside assistance program.
Customer assistance 224 Ford extended service plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
Customer assistance 225 Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle.
Customer assistance 226 Please have the following information available when contacting Ford Customer Assistance: • Y our telephone number (home and business) • The name of the dealer and the city.
Customer assistance 227 • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle's performance as designed • a request for reimb.
Customer assistance 228 T o properly review your case, the Board needs the following information: • legible copies of all documents and maintenance or repair orders relevant to the case • the year.
Customer assistance 229 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board's decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law .
Customer assistance 230 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership.
Customer assistance 231 Ford T riple Clean Ford Ultra-Clear Spray Glass Cleaner * May be sold with the Motorcraft name A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer .
Customer assistance 232 T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adapters Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.
Customer assistance 233 For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers.
Customer assistance 234 ORDERING ADDITIONAL OWNER'S LITERA TURE T o order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan, 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.
Reporting safety defects 235 REPORTING SAFETY DEFECTS (U.S. ONL Y) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to Ford Motor Company .
Index 236 A Page Accessory position on the ignition . . . . . . . . . . . . . . . . . .52 Additives, engine oil . . . . . . . . .165 Air bag supplemental restraint system and child safety seats . . . . . . . .84 description . . . . . . . . . . . . . .
237 Index C Page Child safety restraints built-in child seat . . . . . . . . . . .93 child safety seats . . . . . . . . . . . .99 children and safety belts . . .89, 91 Child safety seats and air bags . . . . . . . . . . . . . . . .84 attaching with tether straps .
Index 238 E Page Engine oil changing oil and filter . . . . . . .165 checking and adding . . . . . . . .165 dipstick . . . . . . . . . . . . . . . . . .163 disposal . . . . . . . . . . . . . . . . . .167 engine oil pressure warning light . . . . . . .
Index 239 H Page High-mount brakelamp . . . . . . .204 Hood latch location . . . . . . . . . . . . . .162 release lever . . . . . . . . . . . . . .162 Horn . . . . . . . . . . . . . . . . . . . . . . .54 I Identification Number , V ehicle (VIN) . . . .
Index 240 M Page Maintenance (see Servicing) Manual transaxle backing up (reverse) . . . . . . . .125 clutch . . . . . . . . . . . . . . . . . . . .123 fluid, capacity . . . . . . . . . . . . .218 shift speeds . . . . . . . . . . . . . . .124 Mileage, calculating fuel economy .
Index 241 S Page Safety belts (see Safety restraints) Safety chains, when towing a trailer . . . . . . . . . . . . . . . . . . . .134 Safety Compliance Certification Label . . . . . . . . . . . . . . . . . . . . . .132 Safety defects, reporting . . . .
Index 242 T Page T ires changing . . . . . . . . . . . . . . . . .146 checking tire pressure . . . . . .185 cleaning . . . . . . . . . . . . . . . . . .212 inspection and maintenance . .185 replacing . . . . . . . . . . . . . . . . .149 rotating . . .
Index 243 4CInden 3/25/99 3:55 PM Page 243.
244 Filling station information UNLEADED FUEL ONL Y Octane 87 58.5 litres (15.4 gallons) Use Motorcraft 5W -30 Formula E Fuel Economy Motor Oil, Ford specification WSS-M2C153-G.
Ein wichtiger Punkt beim Kauf des Geräts Ford 1999 Contour (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ford 1999 Contour noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ford 1999 Contour - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ford 1999 Contour reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ford 1999 Contour erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ford 1999 Contour besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ford 1999 Contour verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ford 1999 Contour. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ford 1999 Contour gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
