Benutzeranleitung / Produktwartung PVS 305SA des Produzenten Extron electronic
Zur Seite of 46
PoleV ault ® Systems (featuring the PVS 305SA) Installation Guide 68-1691-01 Rev . A 08 09 ALSO AV AILABLE: The P oleV ault ® System Installation Video.
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
1-1 PoleV ault Systems Installation • Introduction Intr oduction Overview This guide covers the installation of the Extron PoleV ault ® System in a drop ceiling r oom with a wood or concrete structural ceiling.
PoleV ault Systems Installation • Introduction 1-2 Intr oduction, cont'd PVS 305SA POLEV AU LT SWITCHER INPUT SELECTION 1 2 PEAK NORMAL SI GN AL CONFIG 3 4 5 AUX AUDIO AUDIO LEVEL ADJUST PA GIN.
1-3 PoleV ault Systems Installation • Introduction — Planning Befor e you Begin Installation - Planning Before installation is started, several major factors must be consider ed to ensure that the.
PoleV ault Systems Installation • Introduction — Planning 1-4 Intr oduction — Planning, cont’d • Lighting T ype and contr ol (important for projector image viewing) Ambient light fro.
1-5 PoleV ault Systems Installation • Introduction — Planning c. Location of MediaLink ® Contr oller and W all Plates • Forward and side r each (for full details refer to a copy of "ADA Standards for Accessible Design", "Section 4-2", "Space Allowance and Reach Ranges" ) 30" (76 cm) 10" (25.
PoleV ault Systems Installation • Introduction — Inventory Overview 1-6 Intr oduction — Inventory Overview UPB 25 White 60-773-03 UPB 25 Universal Projector Bra cke t (4)T ur nbuc kles (5) Lag ey e bolts (5) Concrete anchors (2) Cable clamps , Gal Steel (1) Safety wire (15 ft .
1-7 PoleV ault Systems Installation • Introduction — Inventory Overview P oleV ault System 42-108-03 (or 42-109-03*, or 42-110-03*) MLC 104 IP Plus MediaLink Controller MLC 104 IP Plus White 60-81.
Intr oduction — Inventory Overview , cont’d 1-8 PoleV ault Systems Installation • Introduction — Inventory Overview 1-8 b. Items not included The following items are not included. However , input and display devices are essential parts of the system, and at any installation they may vary depending on their use.
1-9 PoleV ault Systems Installation • Introduction — Inventory Overview 1-9 d. Installation tools T o aid the professional installer , this checklist gives the tools recommended to complete the installation.
PoleV ault Systems Installation • Installation 2-1 Installation Overview This overview outlines the basic steps for installing the PoleV ault System. Detailed description of these steps is given in five sections, Stages One though Five. N Additional installation hardware is needed and should be supplied by the installer .
PoleV ault Systems Installation • Installation — Stage 1 2-2 Stage One — Install the Scr een and Pr ojector Stage 1 This stage involves installing the three pieces of har dwar e shown below . Slotted Pipe Slotted Pipe (supplied with PCM 340) Where it goes: Attaches to structural ceiling, rests on suspended ceiling.
PoleV ault Systems Installation • Installation — Stage 1 2-3 Installation — Stage One, cont’d 1. Mark screen location a. Mark the center line and the outer edges of the screen.
2-4 PoleV ault Systems Installation • Installation — Stage 1 e. Using suitable screws, mount the pr ojector onto the projector bracket, i.e., the lower portion of the UPB 25 as shown in step 2e ’s image. Align it so the security flange is at the rear .
PoleV ault Systems Installation • Installation — Stage 1 2-5 Installation — Stage One, cont’d 4. Cut the ceiling tile a. Mark the location of the PCM 340 on the T -frame. This aids putting it back in the correct location when the tile is replaced.
2-6 PoleV ault Systems Installation • Installation — Stage 1 6. Finish Projector Dr op Ceiling Mount installation a. Detach the projector bracket/pr ojector from the adjuster plate. Do not remove the pr ojector bracket from the projector . b. Unscrew the UPB 25 adapter plate fr om the mounting pole.
PoleV ault Systems Installation • Installation — Stage 1 2-7 Installation — Stage One, cont’d 8. Install the electrical box (if requir ed) W All electrical installation should be performed by qualified personnel in accordance with local and national building codes, fire and safety codes, and local and national electrical codes.
2-8 Stage T wo — Install the W all Plates and MLC 104 IP Plus Stage 2 This stage involves installing the devices shown below . A udio and Video Output Po rt (at rear) PVT CV D PVT RGB D Plus AUDIO I.
PoleV ault Systems Installation • Installation — Stage 2 2-9 Installation — Stage T wo, cont’d PVT transmitter installation • CA T 5 T568A signal transmission cables (connects PVT input wall.
2-10 PoleV ault Systems Installation • Installation — Stage 2 N The installation must conform to national and local building and electrical codes, and UL requir ements. Refer to the devices’ user manuals for details. 1. Install the mud rings N These devices can be installed using the supplied mud ring or a wall box.
PoleV ault Systems Installation • Installation — Stage 2 2-11 Installation — Stage T wo, cont’d 2. Pull the cables (at the input locations) The following cables need to be installed: • CA T .
2-12 PoleV ault Systems Installation • Installation — Stage 2 3. Install wall plates a. Connect the CA T 5 cables to the rear of the input devices (for RGB devices, connect cable labeled A to port A and cable B to port B).
PoleV ault Systems Installation • Installation — Stage 2 2-13 Installation — Stage T wo, cont’d 4. Install MediaLink Controller T Before cabling and installing the MLC 104 IP Plus, locate and write down the MAC address of the device for configuring the IP address.
2-14 PoleV ault Systems Installation • Installation — Stage 2 b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector contr ol. N Some projectors r equire NULL connection wiring, which inverts the Tx and Rx connections.
PoleV ault Systems Installation • Installation — Stage 2 2-15 Installation — Stage T wo, cont’d Extron MLC 104 IP Plus Rotate lo ck ing ar m and insert into w a ll opening.
2-16 PoleV ault Systems Installation • Installation — Stage 2 Stage Thr ee — Install the FF 120 Ceiling Speakers Stage 3 This stage involves installing the devices shown below . Where it goes: Installs in ceiling tiles at predetermined location for best acoustics.
PoleV ault Systems Installation • Installation — Stage 3 2-17 Installation — Stage Thr ee, cont’d N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the device’ s user manual for details. 1.
2-18 PoleV ault Systems Installation • Installation — Stage 3 4c Wire the captive screw connector . PVS Switcher Rear P anel Speaker 1 Speaker 2 LR 4/8 Ohms AMPLIFIED OUTPUTS 4-pole Captive Screw .
PoleV ault Systems Installation • Installation — Stage 4 2-19 Stage Four — Install the PMK 550 and the PVS 305SA Stage 4 This stage covers installing the devices shown below .
2-20 PoleV ault Systems Installation • Installation — Stage 4 PVS 305SA and power supply on the PMK 550 base plate (inverted) 2d Slide the base plate up onto the pole and 2e secure with the set scr ews N The installation must conform to national and local building and electrical codes, and UL r equirements.
PoleV ault Systems Installation • Installation — Stage 4 2-21 Installation — Stage Four , cont’d 2b Gather the cables, pass them down the pipe. P oleV ault Switcher Po wer Supply Projector P ole Cable Access Slot 1 1 1 4 2 3 3 4 5 6 T o P ro jector Ca bles from A/V wall plates, MLC 1 04 IP Plus, and FF 120 speak er s.
2-22 PoleV ault Systems Installation • Installation — Stage 4 LR LR LR AU X AUDIO INPUT 5 LINE OUT VO ICELIFT RECEIVER PA GING SENSOR DO NOT GROUND OR SHORT SPEAKER OUTPUTS 1B RGB 1A RGB 2B RGB 2A.
PoleV ault Systems Installation • Installation — Stage 4 2-23 Installation — Stage Four , cont’d b. Screw the UPB 25 adjuster plate back onto the base of the pipe and tuck the cables through the back of the adapter plate.
2-24 PoleV ault Systems Installation • Installation — Stage 5 Stage Five — Congur e the Switcher and the System 1. Congure the switcher — MLS Switcher Conguration program a. Run the DVD (or download) and install on a PC or laptop the Extron MediaLink Switcher Conguration pr ogram.
PoleV ault Systems Installation • Installation — Stage 5 2-25 Installation — Stage Five, cont’d 2. Congure the system — Global Configurator a. Download and install Extron’s Global Congurator (GC) configuration program (available at www .
2-26 PoleV ault Systems Installation • Installation — Stage 5 3. T est the system a. Connect all the input devices (e.g., PC, DVD, document camera, etc.) to the transmitters and power up the input devices. Check that power and signal are pr esent at the transmitters.
PoleV ault Systems Installation • Installation — Stage 5 2-27 Installation — Stage Five, cont’d d. T est the contr oller ’s configuration with the following: • Check that the MLC is controlling the PVS 305SA switcher and projector , and output’s the correct image when switching inputs.
3-1 PoleV ault Systems Installation • Optional Accessory Installation Optional Accessory Installation — V oiceLift System The Extron V oiceLift system is an easy-to-use, low-power , voice amplication system that ensur es the speaker ’s voice can be clearly heard at a comfortable level thr oughout the classroom.
PoleV ault Systems Installation • Optional Accessory Installation 3-2 Optional Accessory Installation — Priority Page Sensor Kit The Priority Page Sensor Kit momentarily silences classroom audio whenever a page is made fr om a public address (P A) system.
3-3 PoleV ault Systems Installation • Optional Accessory Installation LR LR LR AU X A UDIO INPUT 5 LINE OUT PA GING SENSOR DO NOT GROUND OR SHO RT SPEAKER OUTPUTS RS-232 MLC/IR 2/4/8 Ohms CLASS 2 WI.
4-1 Specications For detailed specications and warranty information of the PoleV ault System components, refer to the device manuals, or the product pages at www .extron.com . Mounting hardwar e PCM 340 Mounting .................................
4-2 PoleV ault Systems Installation • Reference Information Regulatory compliance Safety ................................... CE, c-UL, UL UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60065 for safety .
PoleV ault Systems Installation • Reference Information 4-3 Refer ence Information, cont’d Powe r Supply (include d with PV S sw itcher ) w eight 0. 9 lbs (0 .4 kg ) Ext ron UP B 25 Univ ersa l Pr oj ec to r M ounting Brack et w eight 3. 7 lbs (1 .
SIS Command/Response T able Command ASCII (T elnet) (host - switcher) Response (switcher to host) Video Configuration Set the video signal type X! * X2# T yp X! = X2# ] V iew the video signal type X.
Ex tron US A - We st Headquar te rs +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - East +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .9 19 .8 63 .1 79 4 +1 .9 19 .8 63 .1 79 7 FA X Ex tron Europe +8 00 .
Ein wichtiger Punkt beim Kauf des Geräts Extron electronic PVS 305SA (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Extron electronic PVS 305SA noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Extron electronic PVS 305SA - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Extron electronic PVS 305SA reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Extron electronic PVS 305SA erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Extron electronic PVS 305SA besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Extron electronic PVS 305SA verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Extron electronic PVS 305SA. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Extron electronic PVS 305SA gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
