Benutzeranleitung / Produktwartung 400 des Produzenten Extron electronic
Zur Seite of 50
PoleV ault Systems Installation Guide for the PVS 200, 300, and 400 68-1390-01 Rev . D 03 09.
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
1-1 PoleV ault Systems Installation • Introduction Intr oduction Overview This manual covers the installation of the Extron PoleV ault ™ System in a drop ceiling r oom with a wood or concrete structural ceiling above.
PoleV ault Systems Installation • Introduction 1-2 Intr oduction, cont'd L R AU X/MIX IN DO NO T GROU ND OR SHORT SPEAKER OUT PUTS ! 1B 1A I N P U T S O U T P U T S 2B 2A 3B 3A RS-232 MLC/IR DC.
1-3 PoleV ault Systems Installation • Introduction — Planning Befor e you Begin Installation - Planning Before installation is started, you must consider several major factors to ensur e that the .
PoleV ault Systems Installation • Introduction — Planning 1-4 Intr oduction — Planning, cont’d • Lighting T ype and contr ol (important for projector image viewing) Ambient light fro.
1-5 PoleV ault Systems Installation • Introduction — Planning • V iewing obstructions Pillars, furniture etc., window locations for glar e reduction, obstructions between pr ojector and screen c.
PoleV ault Systems Installation • Introduction — Inventory Overview 1-6 Intr oduction — Inventory Overview 2. Inventory a. Included items The PoleV ault System (PVS xxx) ships in two boxes. The larger box (42-1xx-xx) contain the devices and hardwar e, individually boxed and labeled.
1-7 PoleV ault Systems Installation • Introduction — Inventory Overview PVT CV D W allplate PVT CV D White 60-819-13 (1) Mud ring (2) Dog legs (2) Dog leg screws (2) PVT mounting screws (1) Decora ® F aceplate (2) F aceplate screws *P ar t #’ s 42-109-03 and 42-110-03 contain 3 or 4 P oleV ault W allplates, according to type ordered.
Intr oduction — Inventory Overview , cont’d 1-8 PoleV ault Systems Installation • Introduction — Inventory Overview 1-8 N If any items in the PoleV ault System boxes are damaged or missing, contact the Extr on T echnical Hotline (see rear cover for contact numbers).
1-9 PoleV ault Systems Installation • Introduction — Inventory Overview 1-9 b. Items not included The following items are not included. However , input and display devices are essential parts of the system, and at any installation they may vary depending on their use.
PoleV ault Systems Installation • Introduction — Inventory Overview 1-10 Intr oduction — Inventory Overview , cont’d d. Installation tools T o aid the professional installer , this checklist gives the tools recommended to complete the installation.
2-1 PoleV ault Systems Installation • Installation Overview Installation Overview Installation Overview This overview outlines the basic steps for installing the PoleV ault System. Detailed description of these steps is given in five sections, Stages One though Five.
PoleV ault Systems Installation • Installation — Stage 1 2-2 Stage One — Install the Scr een and Pr ojector Stage 1 This stage involves installing the three pieces of har dwar e shown below .
2-3 PoleV ault Systems Installation • Installation — Stage 1 1. Mark screen location a. Mark the center line and the outer edges of screen. T When marking the location of screens, devices, or site for installing transmitters and MediaLink control devices, use painters tape to avoid wall surface damage.
PoleV ault Systems Installation • Installation — Stage 1 2-4 Installation — Stage One, cont’d e. Using suitable screws, mount the pr ojector onto the lower portion of the UPB 25 (the projector bracket, as shown in step 2e ’s image). Align it so the security flange is at the rear .
2-5 PoleV ault Systems Installation • Installation — Stage 1 4. Cut the ceiling tile a. Mark the location of the PCM 240 on the T -bar , before removing it. This aids putting it back in the corr ect location when the tile is replaced. T Mark the screen dir ection on back of the tile (e.
PoleV ault Systems Installation • Installation — Stage 1 2-6 Installation — Stage One, cont’d 6. Secure the Pr ojector Ceiling Mount to the ceiling a.
2-7 PoleV ault Systems Installation • Installation — Stage 1 T Install any optional power outlets in the 2 gang opening on the mounting plate, towards the outside edge of the mount, so it does not interfere with the PMK 450 when installed.
PoleV ault Systems Installation • Installation — Stage 2 2-8 Stage T wo — Install the W all Plates and MLC 104 IP Stage 2 This stage involves installing the devices shown below .
2-9 PoleV ault Systems Installation • Installation — Stage 2 PVT transmitter installation • CA T 5 568A signal transmission cables (connects PVT’s to PVS 204SA switcher) MLC 104 IP Plus instal.
PoleV ault Systems Installation • Installation — Stage 2 2-10 Stage T wo — Install the W allplates and MLC 104 IP Plus N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the devices’ user manuals for details.
2-11 PoleV ault Systems Installation • Installation — Stage 2 2. Pull cables The following cables need to be installed: • CA T 5 cables for signal transmission from the A/V wall plates to the PVS 204SA. N For PVT RGB D wall plates, two CA T 5 signal cables for each input are needed.
PoleV ault Systems Installation • Installation — Stage 2 2-12 Installation — Stage T wo, cont’d 3. Install wall plates a. Connect the CA T 5 cables to the rear of the input devices (for RGB devices, cable labeled A to port A, cable B to port B).
2-13 PoleV ault Systems Installation • Installation — Stage 2 4. Install MediaLink Controller T Before cabling and installing the MLC 104 IP Plus, locate and write down the MAC address of the device for configuring the IP address. The 12 character alphanumeric address (e.
PoleV ault Systems Installation • Installation — Stage 2 2-14 Installation — Stage T wo, cont’d b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector contr ol. c. Connect a CA T 5, 5e, or 6 straight through cable to the MLC ‘s RJ-45 jack.
2-15 PoleV ault Systems Installation • Installation — Stage 2 Extron MLC 104 IP Plus Rotate lo ck ing ar m and insert into wa ll opening. OFF ON OFF ON Extron CONFIG DISPLAY MLC 104 IP Plus VOLUME.
PoleV ault Systems Installation • Installation — Stage 3 2-16 Stage Thr ee — Install the PV SI 3C LP Ceiling Speakers Stage 3 This stage involves installing the devices shown below . Where it goes: Installs in ceiling tiles at predetermined location for best acoustics.
2-17 PoleV ault Systems Installation • Installation — Stage 3 N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the device’ s user manual for details. 1. Cut ceiling tile If installing PV SI 3C LP speakers, do the following: a.
PoleV ault Systems Installation • Installation — Stage 3 2-18 Installation — Stage Thr ee, cont’d e. Loosen the four screws on the fr ont baffle (counter clockwise) ½ turn (see figure, A) and turn the doglegs to lock onto the C-ring. T ighten down the front screws (see gure, B).
2-19 PoleV ault Systems Installation • Installation — Stage 3 c. T o terminate the cable, strip the end of the cable 0.2" (5 mm) and secure the wir es into the supplied 4-pole captive screw connector .
PoleV ault Systems Installation • Installation — Stage 3 2-20 Installation — Stage Thr ee, cont’d 5. Finish speaker installation a. Install/replace the speaker grill on the fr ont of the speaker , using the supplied adhesive tabs (putty) to secure it in place.
2-21 PoleV ault Systems Installation • Installation — Stage 4 Stage 4 This stage covers installing the devices shown below . LR AU X/MIX IN 1B 1A I N P U T S O U T P U T S 2B 2A 4 3 RS-232 MLC/IR .
PoleV ault Systems Installation • Installation — Stage 4 2-22 Installation — Stage Four , cont’d N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the device’ s user manual for details. 1.
2-23 PoleV ault Systems Installation • Installation — Stage 4 3. Install the PVS 204SA switcher a. Pass two 4-40 x 3/16" screws up thr ough the PMK’s bottom plate into the holes in the base of the PVS 204SA switcher , and secure it in place at the left fr ont of the bottom plate.
PoleV ault Systems Installation • Installation — Stage 4 2-24 Installation — Stage Four , cont’d L R AU X/MIX IN 1B 1A I N P U T S O U T P U T S 2B 2A 4 3 RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIF.
2-25 PoleV ault Systems Installation • Installation — Stage 4 FRONT REAR Rear Plate 4c Attach and screw down r ear plate 4d Replace projector on the adjuster plate b. Align the bottom plate lugs with the slots in the top plate and slide up and into place.
PoleV ault Systems Installation • Installation — Stage 5 2-26 Stage Five — Congur e the System Stage 5 Items needed to help complete this stage: • Laptop (or PC) with a network connection • GC 2 conguration program (download from www .
2-27 PoleV ault Systems Installation • Installation — Stage 5 1d Select MLC 104 IP Plus/PoleV ault System from the dr op down box d. Select the MLC 104 IP Plus/PoleV ault system from the drop-down box. Follow the instructions on the help page. e. T o move to the next page shown in the yellow box, click the NEXT button (above the drop-down box).
PoleV ault Systems Installation • Installation — Stage 5 2-28 Installation — Stage Five, cont’d 2c Check that an image is present, adjust as needed. 2. T est the system a. Ensure power is supplied to the PVS 204SA switcher , and power on the MLC 104 IP Plus.
2-29 PoleV ault Systems Installation • Installation — Stage 5 2e Set MLC volume to maximum, and adjust the level on the switcher FRONT REAR F ront Plate Cable from power source Tighten F ront and Rear Plate Screws (4) and Side Screws (2) 3a Replace the front plate and 3b tighten down the screws on the mounting kit d.
PoleV ault Systems Installation • Optional Accessory Installation 2-30 Optional Accessory Installation — PPC 25 The Priority Page Controller (PPC 25) momentarily silences classr oom audio whenever a page is made from a public address (P A) system.
2-31 PoleV ault Systems Installation • Optional Accessory Installation P O WER CN O PA G IN G S ENSO R OUT T IME RELA Y S EN S ITIVITY 1 2 V 0.5 A MAX ON 1 2 L R R S -232 ML C/ IR 4 /8 O hms A MPLIF.
PoleV ault Systems Installation • Optional Accessory Installation 2-32 Optional Accessory Installation — PPC 25 POWER C NO PA GING RELAY DELAY SENSITIVITY 12V 0.
2-33 PoleV ault Systems Installation • Optional Accessory Installation T esting and Adjustment Procedure The fully installed system is shown below T o test that the classroom audio is muted when a P A system announcement (page) occurs: 1 . T urn the classroom audio on.
PoleV ault Systems Installation • Reference Information 2-34 Refer ence Information Specications For detailed specications and warranty information of the PoleV ault System components, refer to the device manuals, or the product pages at www .
2-35 PoleV ault Systems Installation • Reference Information Devices PVS 204SA External power supply ................. 100 V AC to 240 V AC, 50/60 Hz, external; to 12 VDC, 3 A, r egulated Power input requir ements ........... 12 VDC, 0.97 A (typical) T emperatur e/humidity .
PoleV ault Systems Installation • Reference Information 2-36 Installation — Refer ence Information, cont’d Ceiling mount installation diagram (with item weights) for PoleV ault System L R AU X/M.
.
Ex tron US A - We st Headquar te rs +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - East +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .9 19 .8 63 .1 79 4 +1 .9 19 .8 63 .1 79 7 FA X Ex tron Europ e +8 00 .
Ein wichtiger Punkt beim Kauf des Geräts Extron electronic 400 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Extron electronic 400 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Extron electronic 400 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Extron electronic 400 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Extron electronic 400 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Extron electronic 400 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Extron electronic 400 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Extron electronic 400. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Extron electronic 400 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
