Benutzeranleitung / Produktwartung 17001 des Produzenten Extreme Networks
Zur Seite of 274
Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 9505 1 (888) 257-30 00 (408) 579-28 00 http://www . extremenetworks.com Summit ® Family Switches Hardware Installation Guide Summit X.
Summit Family Switches Hard ware Installation Guide 2 AccessAdapt, Alpine, Altitude, BlackDiamond, EPICe nter , ExtremeW orks Essentials, Etherne t Everywhere, Extreme Enabled, Extr eme Ethernet Every.
Summit Family Switches Hardware Installa tion Guide 3 Contents Preface............................................................... ........................................... ............................... .. 9 Conventions ........................
Contents Summit Family Switches Hard ware Installation Guide 4 Summit X450e-48p Power Supplies............................ ..................... .......................... ..... 57 Internal Power Supply ..................... ..................... ....
Contents Summit Family Switches Hardware Installa tion Guide 5 Temperature ......................... ..................... .................... .......................... .....................85 Humidity ......................... .................... .
Contents Summit Family Switches Hard ware Installation Guide 6 Chapter 5: Installing Summit Fam ily Switches .................................................. ............................. 119 Safety Information .................. ...................
Contents Summit Family Switches Hardware Installa tion Guide 7 Removing a Summit X650 AC Power Supply’ ............................... .......................... ........ 165 Removing a DC Power Supply ........... ..................... .............
Contents Summit Family Switches Hard ware Installation Guide 8 Chapter 8: Maintenance Proced ures for Summit X650 and Summit X480 Series Switches .............. 203 Replacing a Summit X650 AC PSU ............... ........... .................... ......
Summit Family Switches Hardware Installa tion Guide 9 Preface This guide pr ovides the instructi ons and supporting information needed to ins tall the following Extreme Netwo rks ® Summit ® switches.
Preface Summit Family Switches Hard ware Installation Guide 10 Related Publications The Extreme Netw orks ExtremeXOS ® switch documentation set incl udes: ● E x t r em eX O S C o n c ep t s G u i d.
1 About the Summit Family Switches.
.
Summit Family Switches Hardware Inst allation Guide 13 1 Summit Family Switches This chapter describes the Summ it family switches and includes the following secti ons: ● Overview of the Summit Swit.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 14 T able 3: Summit Switch Features—Summit X150, X250e, and 350 Series Feature Summit X150 Series Summit X250e Series Summ.
Summit Family Switches Hardware Inst allation Guide 15 Model numbers for the Summit switches ar e in the following format: <Series>-<number of front-panel I/O ports><port type><power supply type> ● The number of ports can be 24 or 48 .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 16 Refer to the following sections for specific har dware details about each Summit seri es: ● Summit X150 Series Switches.
Summit Family Switches Hardware Inst allation Guide 17 connection automatically f ails over to the second connection. T o set up a redundant link on a combination port, connect the active 1000BASE-T and fiber links to both t he RJ-45 and S FP interfaces of that port.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 18 Summit X150-24t Switch The front panel of the Summit X150-24t switch ( Figure 1 ) includes: ● T wenty-four fixed autosensing 10/100BASE-T po rts (port s 1–24) that provide 2.
Summit Family Switches Hardware Inst allation Guide 19 Summit X150-24p Switch The front panel of the Summit X150-24p switch ( Figur e 3 ) includes: ● T wenty-four fixed autosensing 1 0/100BASE-T Po E po rts (ports 1–24). In addit ion to 4 Gbps of high-density copper connectivity , these ports also provide a full 15.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 20 Summit X150-48t Switch The front panel of the Summit X150-48t switch ( Figure 5 ) includes: ● Forty-eight fixed autosensing 10/100B AS E-T ports (ports 1–48) that pr ovide 4.
Summit Family Switches Hardware Inst allation Guide 21 Summit X150 Series Switch LEDs Ta b l e 7 lists the of LEDs on the Summit X150 switches, al ong wit h their associat ed colors and meani ngs.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 22 Summit X250e Series Switches The Summit X250e series switches pr ovide 24 or 48 Ethernet ports that deliver high-density fast Ethernet connectivity using fixed 10/100 /1000BASE-T ports or installable small form pluggable (SFP) optical modules.
Summit Family Switches Hardware Inst allation Guide 23 Summit X250e-24t Switch The front panel of the Summit X250e-24t switch ( Figure 7 ) includes : ● T wenty-four fixed autosensing 10/100BASE-T po rts (port s 1–24) that provide 2.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 24 Summit X250e-24tDC Switch The front panel of the Summit X250e-24tDC switch ( Figur e 33 ) includes: ● T wenty-four fixed autosensing 10/100BASE-T po rts (port s 1–24) that provide 2.
Summit Family Switches Hardware Inst allation Guide 25 Figure 10: Summit X250e-24tDC Switch Rear Panel Summit X250e-24p Switch The front panel of the Summit X250e-24p switch ( Figure 1 1 ) includes: ● T wenty-four fixed autosensing 1 0/100BASE-T Po E po rts (ports 1–24).
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 26 The rear panel of the Summit X250e-24p switch ( Figur e 12 ) includes: ● Management port with associated LEDs ● T wo high-performance stacking ports with associated LEDs ● Redundant power input connector for use with the EPS-500 External Power Supply (Model N o.
Summit Family Switches Hardware Inst allation Guide 27 Figure 13: Summit X250e-24x Switch Front Panel The rear panel of the Summit X250e-24x switch ( Figur e 8 ) includes: ● Management port with ass.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 28 Summit X250e-24xDC Switch The front panel of the Summit X250e-24xDC switch ( Figure 7 ) includes: ● T wenty-four 100BASE-FX p orts (ports 1–24) that prov ide 2.
Summit Family Switches Hardware Inst allation Guide 29 Figure 16: Summit X250e-24xDC Switch Rear Panel Summit X250e-48t Switch The front panel of the Summit X250e-48t switch ( Figure 17 ): ● Forty-eight fixed autosensing 10/100BASE-T ports (p ort s 1–48) that provide 4.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 30 The rear panel of the Summit X250e-48t switch ( Figure 18 ) includes : ● Management port with associated LEDs ● T wo .
Summit Family Switches Hardware Inst allation Guide 31 The rear panel of the Summit X250e-48tDC switch ( Figure 18 ) includes : ● Management port with associated LEDs ● T wo high-performance stacking ports with associated LEDs ● Redundant power input connector for use with the EPS-150DC Ext ernal Power Module (Model No.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 32 Summit X250e-48p Switch The front panel of the Summit X250e-48p switch ( Figure 21 ) includes: ● Forty-eight fi xed autosensing 1 0/100BASE-T PoE po rts (ports 1–48). In addition to 4.
Summit Family Switches Hardware Inst allation Guide 33 Summit X250e-48p Power Supplies The Summit X250e-48p switch is powered by both an internal power supply and an opt ional external redundant power supply system.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 34 Summit X250e Series Switch LEDs Ta b l e 9 descri bes the LED s on the Su mmit X250e sw itches.
Summit Family Switches Hardware Inst allation Guide 35 Additional Port LED Meanin gs for PoE Switches: Summit X250e-24p & Summit X250e -48p All front-panel ports Steady green Link OK. port no t powered. Steady amber Link OK, port is powered, no traffic Blinking green Link OK, transmitting packets, port not powered.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 36 Summit X350 Series Switches The Summit X350 series switches pr ovide 24 or 48 Ethern et ports that deliver high-density fast Ethernet connectivity using fixed 10/100/1000BA SE-T ports.
Summit Family Switches Hardware Inst allation Guide 37 Summit X350-24t Switch The front panel of the Summit X350-24t switch ( Figure 23 ) includes: ● T wenty fixed autosensing 10/100/1000BASE-T po r.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 38 Figure 24: Summit X350-24t Switch Rear Panel Summit X350-48t Switch The front panel of the Summit X350-48t switch ( Figur.
Summit Family Switches Hardware Inst allation Guide 39 The rear panel of the Summit X350-48t switch ( Figur e 40 ) includes: ● Slot for the one of the following Summit option car ds: ■ Summit XGM2-2xn option card, which allows yo u to add one or two 10 -gigabit XFP modules See “Summit XGM2-2xn Option Card” on page 197 .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 40 Summit X350 Series Switch LEDs Ta b l e 1 2 lists the LED s and their as so ciated colors and meanings.
Summit Family Switches Hardware Inst allation Guide 41 Summit X450, X450a, and X450e Series Switches The Summit X450 series, Summ it X450a series, and Summit X450 e series switches provide 24 or 48 Ethernet ports.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 42 Summit X450 Series Switches The Summit X450 series switches ar e 24-port switches without PoE options. The ports ar e implemented as fixed 10/100/1000BASE-t RJ-45 ports or as installa ble SFP modules.
Summit Family Switches Hardware Inst allation Guide 43 ● Redundant power input connector for optional co nnection to the EPS-160 External Power Module (Model No. 10907). See “EPS-160 External Power Module (with EPS-T)” on page 75 for mor e information.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 44 The rear panel of the Summit X450-24x switch ( Figur e 30 ) includes: ● Slot for the Summit XGM-2xn option card, which .
Summit Family Switches Hardware Inst allation Guide 45 Summit X450a Series Switches The Summit X450a series switches are 24-port or 48 -port switches without PoE options. The Ethernet ports are implemented as fixed 10/100/1000BASE-T RJ -45 ports or as instal lable SFP modules.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 46 Figure 31: Summit X450a-24t Switch Front Panel The rear panel of the Summit X450a-24t switch ( Figure 32 ) includes: ● .
Summit Family Switches Hardware Inst allation Guide 47 Summit X450a-24tDC Switch The front panel of the Summit X450a -24tDC switch ( Figure 33 ) includes: ● T wenty fixed autosensing 10/100/1000 BAS.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 48 NOTE For centralized DC power connection, this product is intended to be installed in a restri cted access location (such.
Summit Family Switches Hardware Inst allation Guide 49 The rear panel of the Summit X450a-24x switch ( Figure 36 ) includes: ● Slot for one of the following Summit option cards: ■ Summit XGM2-2xn .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 50 Summit X450a-24xDC Switch The front panel of the Summit X450a-24 xDC switch ( Figure 37 ) includes : ● T wenty fixed autosensing 1000BASE- X ports (ports 1-20) that provide 20 Gbps of high-density fiber (SFP) connectivity ● Four combination ports (port s 21-24).
Summit Family Switches Hardware Inst allation Guide 51 NOTE For centralized DC power connection, this product is intended to be installed in a restri cted access location (such as a dedicated equipment room, equipment closet, or central office) in accordance with Articles 110-16, 110-17, and 110-18 of the National Electric Code, ANSI/NFP A 70.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 52 The rear panel of the Summit X450a-48t switch ( Figure 40 ) includes: ● Slot for one of the following Summit option car.
Summit Family Switches Hardware Inst allation Guide 53 Figure 41: Summit X450a-48tDC Switch Front Panel The rear panel of the Summit X450a-48tDC switch ( Figure 40 ) includes: ● Slot for one of the .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 54 Summit X450e Series Switches The Summit X450e series switches ar e 24-port or 48 -port PoE-capable switches. The Etherne t ports are implemented as fixed 10/100/1000BA SE-T RJ-45 ports.
Summit Family Switches Hardware Inst allation Guide 55 The rear panel of the Summit X450e-24p switch ( Figur e 44 ) includes: ● Slot for one of the following Summit option cards: ■ Summit XGM2-2xn.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 56 Summit X450e-48p Switch The front panel of the Summit X450e-48p switch ( Figure 45 ) includes: ● Forty-four fixed autosensing 10/1 00/1000 BASE-T PoE ports (ports 1-44) that provide high-density copper connectivity and a full 15.
Summit Family Switches Hardware Inst allation Guide 57 Figure 46: Summit X450e-48p Switch Rear Panel Summit X450e-48p Power Supplies The Summit X450e-48p switch is powered by both an internal power supply and an opt ional external redundant power supply system.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 58 For more information, see “EPS-600LS External Power Module” on page 77 . Summit X450, X450a, and X450e Series Switch LEDs Ta b l e 1 2 describes the LEDs for the Summit X450, X450a, and X450e switches.
Summit Family Switches Hardware Inst allation Guide 59 PSU-E (External power supply) Steady green Normal operation Blinking amber Failure Off No external power attached Ethernet Ports 1 – 24 or 1 – 48 (21 –24 and 45 – 48 are shared ports) Steady green Link OK Blinking green Activity Off Link is not present or port is disabled.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 60 Summit X480 Series Switches The Summit X480 series switches ar e 24-port or 48-port switches th at provide Ethernet connectivity using fixed 10/100/1000BASE-T R J- 45 ports, installable SFP opti cal modules, or installable X FP optical modules.
Summit Family Switches Hardware Inst allation Guide 61 Summit X480-24x Switch The front panel of the Summit X480-24x switch ( Figure 47 ) includes: ● T welve autosensing 100/1000BASE-X ports (ports .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 62 Summit X480-48x Switch The front panel of the Summit X480-48x switch ( Figure 49 ) includes: ● Forty-eight 100/1000BASE.
Summit Family Switches Hardware Inst allation Guide 63 Summit X480-48t Switch The front panel of the Summit X480-48t switch ( Figure 51 ) includes: ● Forty-four fixed 10/100/1000BASE-T autosensing p.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 64 VIM2-SummitStack V ers atile Interface Module The VIM2-SummitStack module ( Figure 53 ) pr ovides two high-performance stacking ports that allow you to combine multiple units into a single SummitStack management entity .
Summit Family Switches Hardware Inst allation Guide 65 VIM2-SummitStack128 V ers atile Interface Module The VIM2-SummitStack128 vers a tile interface module ( Figure 55 ) provides two 64-Gbps SummitStack stacking ports. T o connect these p orts, you mu st use stacking ca bles with compatible connectors, available from Ex treme Ne tworks.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 66 Summit X480 Series Switch LEDs Ta b l e 1 4 describes the LEDs on the Summit X480 series swi tches.
Summit Family Switches Hardware Inst allation Guide 67 Summit X650 Series Switches The Summit X650 series switches pr ov ide 24 front-panel Ethernet ports that provide 10 -gigabit Ethernet connectivity using fixed 10GBASE-T RJ-45 port s or in stallable SFP+ optical modules.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 68 Summit X650-24t Switch The front panel of the Summit X450-24t switch ( Figure 56 ) includes: ● T wenty-four fixed autos.
Summit Family Switches Hardware Inst allation Guide 69 Summit X650-24x Switch The front panel of the Summit X450-24x switch ( Figure 58 ) includes: ● T w e n t y - f o u r p o r t s t h a t c a n u s e 1 0 G B A S E - X S F P + o p t i c a l m o d u l e s .
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 70 VIM1-SummitStack V ers atile Interface Module The VIM1-SummitStack versatile interface module ( Figure 60 ) pr ovides four cages for ins talled SFP optical modules. These ports (numbered 25 through 28) function the same a s the fron t-panel ports.
Summit Family Switches Hardware Inst allation Guide 71 VIM1-SummitStack512 V ers atile Interface Module The VIM1-SummitStack512 versatile interface module ( Figu re 62 ) pr ovides four 128-Gbps sta cking ports that are used to cr oss-connect two Summit X650 series switches.
Summit Family Swi tches Summit Family Switches Hard ware Installation Guide 72 Summit X650 Series Switch LEDs Ta b l e 1 5 describes the LEDs on the Summit X650 series swi tches.
Summit Family Switches Hardware Inst allation Guide 73 2 Summit Power Supplies This chapter describes Extr eme Networks power su pplies available for use w ith the Summit family switches. The Summit X650 series switches have r e placeable power supplies; redundant external power supplies are available for the other Summit series.
Summit Power S upplies Summit Family Switches Hard ware Installation Guide 74 NOTE The Summit switches listed in each section of this chapter run ExtremeXOS software. For information about compatible switches running ExtremeW are ® software, refer to the Consolidated “i” and “e” Series Hardware Installation Guide .
Summit Family Switches Hardware Inst allation Guide 75 EPS-160 External Power Module (with EPS-T) The EPS-160 External Power Module (Model 10907) is a modu lar powe r supply for use with the EPS-T chassis.
Summit Power S upplies Summit Family Switches Hard ware Installation Guide 76 EPS-500 External Power Supply Unit The Extre me Networks EPS-500 External Power Supply Unit (Mod el 1091 1) provides additional power to compatible Power over Ethernet (P oE) switches and other Extr eme switches.
Summit Family Switches Hardware Inst allation Guide 77 EPS-600LS External Power Module The EPS-600LS External Power Modu le (Model 10913) is a 600-watt redundant power supply unit that can be used wit.
Summit Power S upplies Summit Family Switches Hard ware Installation Guide 78 Dual 600-LS Module C onfiguration: Full Power T wo EPS-600LS power modules provide full power at 740 W , which allows 15.
Summit Family Switches Hardware Inst allation Guide 79 Disconnecting the E PS-C/EPS-600LS. T o m a n u a l l y d i s c o n n e c t a n E P S - C o r t o r e m o v e t h e E P S - 6 0 0 L S modules, the recommend ed practice is to disconnect the EPS-600LS mo dules one at a time, pausing two seconds between each EPS-600LS disconnect.
Summit Power S upplies Summit Family Switches Hard ware Installation Guide 80 Summit X650 Power Supplies The Summit X650 series switches can be power e d by either of the following power supplies: ● Summit X650 AC PS U (Model 10914) ● Summit X650 DC PSU (M odel 10915) Either power supply provides 850 W of power to the switch.
2 Installing the Hardware.
.
Summit Family Switches Hardware Inst allation Guide 83 3 Site Preparation This chapter includes the foll owing sections: ● Planning Y our Site on page 83 ● Meeting Site Require ments on page 84 .
Site Preparation Summit Family Switches Hard ware Installation Guide 84 ● Meeting power r equire ments T o run your equipment safely , you must meet the specific power r equirements for each switch and external power supply unit installed in the syst em.
Summit Family Switches Hardware Inst allation Guide 85 the electronics industr y . The address is EIA; 2500 W ilson Boulevard; Arlington, V irginia 22201 USA.
Site Preparation Summit Family Switches Hard ware Installation Guide 86 NOTE As with all electrical equipment, Ex treme Networks product lifetimes degr ade with increased temperature. If possible, temperatures should be kept at approximately 78 ° F (25 ° C ) o r l o w e r .
Summit Family Switches Hardware Inst allation Guide 87 Mechanical Recommenda tions for the Rack Use equipment racks that meet the following mechanical recommendations: ● Use an open style, 19-inch rack to facilitate ea sy maintenance and to pr ovide proper ventilation.
Site Preparation Summit Family Switches Hard ware Installation Guide 88 Securing the Rack T h e r a c k s h o u l d b e a t t a c h e d t o t h e w i r i n g c l o s e t f l o o r w i t h 3 / 8 - i n c h ( 9 . 5 m m ) l a g s c r e w s o r e q u i v a l e n t hardwar e.
Summit Family Switches Hardware Inst allation Guide 89 Cable Labeling and Record Keeping A reli able cable labeling system is essential when planning and installing a network . Maintaining accurate recor ds helps you to: ● Relocate devices easily . ● Make changes quickly .
Site Preparation Summit Family Switches Hard ware Installation Guide 90 ● Use plenum-rated cable when it is necessary for safety and fir e rating requir ements.
Summit Family Switches Hardware Inst allation Guide 91 NOTE Kinks and sharp bends can destroy or impair the cable’ s ability to convey light pulses accurately from one end of the cable to the other .
Site Preparation Summit Family Switches Hard ware Installation Guide 92 RJ-45 Connector Jackets Use RJ-45 cable with connector jackets that are flush with the connector or that have connectors with a no-snag feature.
Summit Family Switches Hardware Inst allation Guide 93 Meeting Power Requirements This section describes power requirements, including: ● PoE Devices ● Power Supply Requir ements ● AC Power Cabl.
Site Preparation Summit Family Switches Hard ware Installation Guide 94 Uninterruptible Powe r Supply Requirements An uninterruptible power supply (UPS) is a d evice th at sits betwee n a power supply.
Summit Family Switches Hardware Inst allation Guide 95 UPS T ransition T ime T ransition time is the time that is necessa ry for the UP S to transfer from utility power to full-l oad battery power . For Extreme Networks pr oducts, a transiti on time of less than 20 mill iseconds is required for optimum performance.
Site Preparation Summit Family Switches Hard ware Installation Guide 96.
Summit Family Switches Hardware Inst allation Guide 97 4 Building a SummitStack Configuration This chapter provides inf ormation about how to buil d and connect a SummitStack configuration.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 98 all the software table s for all the switches in the st ack. A stac k of switches can have only one master switch. All switches in the stack, includ ing the m aster sw itch, are called n odes.
Summit Family Switches Hardware Inst allation Guide 99 Stack configuration, easy setup, and redundancy ar e fully described in the E x t r em eX O S C o n c ep t s G u i d e .
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 100 Placing Summit Family Switch es for Stacked Operation This section summarizes the r ecommended best pr actices for installing Summit switches for a SummitStack configuration.
Summit Family Switches Hardware Inst allation Guide 101 Switches from some Summit series have mor e memory than other Summit models and support additional featur es.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 102 Figure 70: Summ itStack Cable Co nnec tions Using Four Summit Switches with Integrated SummitStack Ports Ta b l e 2 0 lists the recommend ed orde r for connecting the stacking ports in this example.
Summit Family Switches Hardware Inst allation Guide 103 Figure 71 shows cable connections for an 8-node stac k using Summit Stack 40G cables to connect switches with integrated SummitStack ports.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 104 Figure 72: SummitStack Configuration Us ing SummitStack X650 Series Switches and SummitStack 40G Cables Mu.
Summit Family Switches Hardware Inst allation Guide 105 Figure 74 shows five sw itches installed at the tops of fi ve adjacent r acks. T o accommodate the shortest possible cables, immedi ately adjacent switches a re no t always connected together . Port 2 on one switch is connected to Port 1 on the next connected switch.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 106 Figure 75: Combining Stacki ng Port T ypes The following cables ar e used to make the stacking connections.
Summit Family Switches Hardware Inst allation Guide 107 Using the VIM1-SummitStack512 Module The VIM1-SummitStack51 2 versatile interface module allows you to connect two Summit X 650 series switches in a cross-over or back-to-back co nfiguration, using SummitStack 128 G cables ( Figure 76 ).
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 108 Connecting Stacking Cables T o connect Summit switches in a Su mmitStack configuration, use the a ppropriate stacking cables for the specific stacking ports on the s witches.
Summit Family Switches Hardware Inst allation Guide 109 Connecting a SummitStack 128G Cable SummitStack 128G cables are used to connect the 128-Gbps stacking ports on the VIM1-SummitStack256 and VIM1-SummitStack512 modules in Summit X650 series switches.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 110 T o connect a SummitStack 128G cable: 1 Holding the cable connector with the release tab on top, align the connector with the stacking port on the VIM1 module in the Summit X650 series switch ( Figure 80 ).
Summit Family Switches Hardware Inst allation Guide 111 Connecting a SummitStack 128G/20G Stacking Cable SummitStack 128G/20G cables a re used to connect th e 128-Gbps stacking ports on Summit X650 series switches to 20-Gbps stacking ports on Summit X650 series or other Summit series switches.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 112 Figure 82: Conne cting the 20G Connector ES4K037.
Summit Family Switches Hardware Inst allation Guide 113 Connecting a SummitStack 128G/64G Stacking Cable SummitStack 128G/64G cables a re used to connect th e 128-Gbps stacking ports on Summit X650 series switches to 64-Gbps stacking ports on Summit X480 se ries switches.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 114 At the Summit X650 series switch , connect the 128G connector to the VIM1-SummitStack256 module. At the Summit X480 series switch, connect the 64G connector to the VIM2-SummitStack128 module.
Summit Family Switches Hardware Inst allation Guide 115 Connecting a SummitStack 64G Stacking Cable SummitStack 64G cables are used to connect the 64-Gbps stac king ports on the VIM2 -SummitStack128 module in Summit X480 series switches.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 116 T o connect a SummitStack 64G cable: 1 Holding the cable connector with the release tab on top, align the connector with the stacking port on the VIM2 module in the Summit X480 series switch ( Figure 88 ).
Summit Family Switches Hardware Inst allation Guide 117 Connecting a SummitStack 64G/20G Stacking Cable SummitStack 64G/20G cables are us ed to connect the 64-Gbps stacking ports on Summi t X480 series switches to 20-Gbps stacking ports on Summit X480 series, Summit X650 series, or other Summit series switches.
Building a Su mmitStack Configuration Summit Family Switches Hard ware Installation Guide 118 Figure 90: Conne cting the 20G Connector Connecting Console Ports for a Stack T o begin the software configur ation for a new stack, y o u m u s t h a v e a t l e a s t o n e console port connected.
Summit Family Switches Hardware Inst allation Guide 119 5 Installing Summit Family Switches This chapter describes how to install and r emove Summit family switche s and associated components. The chapter also includes information about conne cting network interface cables and establishing management access.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 120 Installing a Summit Family Switch (Models Other than Summit X480 and X650 Series) This section describes how .
Summit Family Switches Hardware Inst allation Guide 121 T o install the swit ch in a rack, you need t he following tools and equipment: ● Mounting brackets (provided) ● Screws (pr o vided) to secu.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 122 8 Connect the power cables. ● For AC-powered units , connect the power cable to the AC power connector on the back of the switch. Then connect the power cable to an AC power socket.
Summit Family Switches Hardware Inst allation Guide 123 NOTE For centralized DC power connection, these products are in tended to be installed in Restricted Access Locations (Dedicated Equipment Rooms, Equipmen t Closets, or the like) in accordance with Articles 11 0-16, 110-17, and 110-18 of the National Electric Code, ANSI/NFP A 70.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 124 Figure 92: Location of the Ground ing Lug 3 Insert the stripped wir e into the grounding lug (see Figure 93 and Figure 94 ).
Summit Family Switches Hardware Inst allation Guide 125 Connecting the DC Wi ring Harness to the DC Source V oltage A f t e r t h e i n t e r n a l D C p o w e r s u p p l y i s i n s t a l l e d , i t m u s t b e c o n n e c t e d t o a D C p o w e r s o u r c e .
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 126 Attaching the DC Wiring Harness to the DC Power So cket on the Switch After the DC wiring harness is connecte.
Summit Family Switches Hardware Inst allation Guide 127 CAUTION Be sure that proper ESD controls are in use before switch maintenance is performed. This incl udes but is not limited to wrist straps that are grounded to the switch chassis and earth grounds.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 128 ● Sides: For a two-post rack install ation, allow adequate space for access to the sides of the switch so that the front mounting brackets can be attached to the switch.
Summit Family Switches Hardware Inst allation Guide 129 3 From the back of the equipment rack, s lide the switch into place over the mounting brackets (see Figur e 98 ). Make sure the brackets s lide between the support pegs on both sides of the switch.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 130 5 At the front of the switch, place a fr ont mounting br acket against each side of the switch, in f ront of .
Summit Family Switches Hardware Inst allation Guide 131 Front-Mounting the Switc h in a T wo-Post Rack T o front-mount the switch in a two-post rack: 1 Place the switch upright on a secur e work surface. 2 Place a front mounting bracket over the mounting ho les on one side of the unit, with the flange at the front of the switch ( Figur e 102 ).
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 132 After the switch is secured to the rack, inst all and connect power su pplies as described on page 135 fo r AC power supplies or on page 136 for DC power supplies.
Summit Family Switches Hardware Inst allation Guide 133 Figure 105: Attaching a Fron t Mounting Bracket 5 From the fr ont of the rack, slide the switch onto the rear mounting brackets ( Figu re 106 ).
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 134 Figure 107: Securing the Switch to the Fr ont Rack Posts—Four -Post Installation After the switch is secured to the rack, inst all and connect power su pplies as described on page 135 fo r AC power supplies or on page 136 for DC power supplies.
Summit Family Switches Hardware Inst allation Guide 135 Installing a Summit X480 AC PSU WAR NI NG ! T o prevent an electrical hazard, make sure that the AC po wer cord is not connect ed to the PSU before you install the PSU in the power supply bay . CAUTION Make sure that the AC PSU ci rcuit is not overloaded.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 136 Figure 109: Installing a PSU 5 T o install an additional PS U, repeat steps 2 thr ough 4. NOTE If PSUs are not instal led in both power s upply bays, be sure to insta ll a cover over the unoccupied bay .
Summit Family Switches Hardware Inst allation Guide 137 CAUTION Make sure that the Summit X480 DC PSU circuit is not overloa ded. Use pr oper over -current protection, such as a circuit-breaker , to prevent over -curre nt conditions. Do not use a breaker rated for higher than 30 Amps.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 138 Figure 110: Attaching a T erminal to a Cable Installing the Power Supply T o install a Summit X480 DC PSU: 1 Attach an ESD-preventive wrist strap to your bar e wrist and connect the metal end to an appropriate ground point on the rack.
Summit Family Switches Hardware Inst allation Guide 139 Figure 112: Installing a DC PSU 5 T o install an additional PS U, repeat steps 2 thr ough 4. Connecting the Ground Wire WAR NI NG ! Be sure to connect the chassis ground wire before you connect any power cables.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 140 Figure 113: Connecting th e Ground Wire 5 Connect the ground wir e to the grounding point as follows: a Loosen the scr ew enough to allow the spade te rm inal to slide underneath the captive square washer ( Figure 1 14 ).
Summit Family Switches Hardware Inst allation Guide 141 Figure 114: Securing the Ground Wire 6 Connect the other end of the wire to a known r e liable earth ground point at you r site.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 142 b Slide the spade terminal of the negati ve w i r e ( – 4 8 V ) u n d e r t h e c a p t i v e s q u a r e w a s h e r o n t h e negative terminal (labeled – ).
Summit Family Switches Hardware Inst allation Guide 143 Figure 116: Connecting the D C Power Cables (Part 2 ) 5 Connect the cables to the DC source voltage, using har dware appropriate to the installation site and following local and national electrical cod es.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 144 Removing a Summit X480 AC Power Supply CAUTION The PSU may be hot to the touc h; wear thermal prot ec tive gloves when handling the PSU during removal.
Summit Family Switches Hardware Inst allation Guide 145 T o remove a Summit X480 DC PSU: 1 De-energize the DC cir cuit. 2 Attach an ESD-preventive wrist strap to your bar e wrist and connect the metal end to an appropriate ground point on the rack. 3 Disconnect the DC power cables as follows: a Pull the cover off the terminal block.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 146 T o remove a mid-mounted Summit X480 series switch fr om a two-post rack: 1 Attach an ESD-preventive wrist strap to your wr ist and connect the me tal end to an appr opriate ground point on the rack.
Summit Family Switches Hardware Inst allation Guide 147 6 R e m o v e t h e r a c k - m o u n t i n g s c r e w s a n d d e t a c h t h e r e a r m o u n t i n g b r a c k e t s f r o m t h e r a c k p o s t ( Figure 121 ).
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 148 Figure 122: Removing a Front-Moun ted Switch from a T wo-Post Rack Removing a Switch from a Four -Post Rack Removing the Summit X650 switch from a cabinet or ra ck requir es two people to maneuver the switch and disconnect the mounting hard ware .
Summit Family Switches Hardware Inst allation Guide 149 Figure 123: Removing the Switch from a Four -Post Rack 5 S e t t h e s w i t c h o n a s e c u r e w o r k s u r f a c e . U s i n g a #1 Phillips screwdriver , re move the front mounting brackets from the sides of the switch.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 150 NOTE T ake care to load the rack so that it is not top-heavy . Start installing equipment at the bottom and work up. Pre-installation Requirements Installing the Summit X6 50 switch requires two peop le to maneuver the swit ch and attach mounting ha rd wa re.
Summit Family Switches Hardware Inst allation Guide 151 Figure 124: Attaching a Re ar Mounting Bracket—T wo-Post Rack Installation 3 From the back of the equipment rack, s lide the switch into place over the mounting brackets (see Figure 125 ). Make sur e the brackets slide between the support pegs on both sides of the switch.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 152 Figure 126: Fastening the Rea r Mounting Brackets—T wo-Post Rack S H_09 8.
Summit Family Switches Hardware Inst allation Guide 153 5 At the front of the switch, place a fr ont mounting br acket against each side of the switch, in f ront of the ventilation openings in the side of the switch ( Figure 127 ) Make sure ther e is space between the bracket and the ventilation openings.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 154 After the switch is secured to the rack, inst all and connect power su pplies as described in “Installing a Summit X650 AC Power Su pply” on page 157 or “Installing a Summit X650 DC Power Su pply” on page 158 .
Summit Family Switches Hardware Inst allation Guide 155 Figure 130: Attaching the Front Moun ting Brackets—Cabinet Installation 5 From the front of the cabinet, slide the switch onto the r ear mounting brackets ().
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 156 Figure 132: Securing the Sw itch to the Front Rack Po sts—Cabinet Installation 7 A t e a c h s i d e , f a s t e n t h e m o u n t i n g b r a c k e t t o t h e b a c k r a c k p o s t u s i n g s u i t a b l e s c r e w s .
Summit Family Switches Hardware Inst allation Guide 157 Installing a Summit X650 AC Power Supply CAUTION Make sure that the AC PSU ci rcuit is not overloaded. Use proper over -cu rrent protection, such as a circuit-breaker , to prevent over -current conditions.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 158 Figure 134: Installing a PSU 5 T o install a second PSU, r epeat steps 3 and 4 . NOTE If PSUs are not installed in both power supply bays, be sure to install a cover over the unoccupied bay .
Summit Family Switches Hardware Inst allation Guide 159 Required T ools and Materials Y ou need the following tools and materials to install or remove a Summit X650 DC PSU: ● T wo spade terminals (T.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 160 Figure 135: Attaching T erminals to Cables Installing the Power Supply CAUTION The handle on the Summit X650 DC PSU is not designed to be used to lift or carry the Summit X650 series switch.
Summit Family Switches Hardware Inst allation Guide 161 Figure 137: Installing a Summit X650 DC PSU 5 T o install mor e PSUs, r epeat steps 3 and 4 . Connecting the Ground Cable WAR NI NG ! Be sure to connect the chassis ground wire before you connect any power cables.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 162 Figure 138: Connecting th e Ground Wire Connecting the PSU to the DC Source V oltage The DC power connection at your facility mu s t be made by a qual ified electricia n, following the instructions in this secti on.
Summit Family Switches Hardware Inst allation Guide 163 Figure 139: Connecting the D C Power Cables (Part 1 ) d T ighten both screws on the terminal block to 1 1 inch-pounds ( Figure 140 ). 5 Slide the cover into place over the terminal block ( Figure 140 ).
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 164 Figure 140: Connecting the D C Power Cables (Part 2 ) 6 Connect the cables to the DC source voltage, using har dware appropriate to the installation site and following local and national electrical cod es.
Summit Family Switches Hardware Inst allation Guide 165 Removing a Summit X650 AC Power Supply’ T o remove an AC power supply: 1 Attach an ESD-preventive wrist strap to your wr ist and connect the me tal end to an appr opriate ground point on the rack.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 166 4 Disconnect the gr ound wire as follows: a Remove the screw that secur es the ground wir e to th e PSU.
Summit Family Switches Hardware Inst allation Guide 167 Figure 143: Removing the Front Mounting Screws from a T wo-Post Rack 4 Remove the screws holding the fr ont mounting br ackets to t he sides of the swi tch, and set t he mounting brackets aside.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 168 6 R e m o v e t h e r a c k - m o u n t i n g s c r e w s a n d d e t a c h t h e r e a r m o u n t i n g b r a c k e t s f r o m t h e r a c k p o s t ( Figure 145 ).
Summit Family Switches Hardware Inst allation Guide 169 Figure 146: Removing the Switch from a Cabinet 6 S e t t h e s w i t c h o n a s e c u r e w o r k s u r f a c e . U s i n g a #1 Phillips screwdriver , re move the front mounting brackets from the sides of the switch.
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 170 NOTE Cables used for connection to the 10GBASE-T ports on the Summit X650-24t switch must meet the minimum requirements of the IEEE 802.3an standard. W orking carefully , one port at a time: 1 V erify that you have id entified the correct cable for the port.
Summit Family Switches Hardware Inst allation Guide 171 Logging In for the First T ime After your switch has complete d all power on self-tes ts, it is operational. Y ou can log in and configur e an IP address for the default VLAN (named de f a u l t ).
Installing Summi t Family Switches Summit Family Switches Hard ware Installation Guide 172.
Summit Family Switches Hardware Inst allation Guide 173 6 Installing Summit External Power Supplies This chapter describes how to install external po wer supp lies with th e Summit fa mily switch es.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 174 When the PSU is outside the chassis (not installed), do not plug th e PSU into an electrical outlet. Plugging an uninstalled AC PSU into an electrical outlet exposes you to a hazardous ener gy and is a potential fire hazard.
Summit Family Switches Hardware Inst allation Guide 175 Rack-Mounting the EPS-T CAUTION Do not use the rack-mount brackets to suspen d the EPS-T fro m under a table or desk, or to attach the EPS-T to a wall. T o rack mount the EPS-T : 1 Place the EPS-T upright on a stable surface, with the fr ont facing you.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 176 Connecting the EPS-160 Po wer Supply to the Switch One end of the EPS-160 redundant power cord has a keyed connector to ensur e correct alignment of the connector ( Figur e 148 ).
Summit Family Switches Hardware Inst allation Guide 177 3 Connect an appropriate AC power cor d to the AC connector on each unit. NOTE An AC power cord is not provi d ed with the EPS-160 unit. See “Selecting Power Supply Cords” on page 218 for information about selecting a power cord.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 178 Rack-mounting the EPS-LD Power Supply NOTE When installing an EPS-LD in a rack, make sure air vent s are not restricted. Allow for elevated ambient operating temperatures when the EPS-LD is inst alled adjacent to other equipment.
Summit Family Switches Hardware Inst allation Guide 179 Connecting the EPS-LD to the Switch CAUTION Do not attach the AC power cord to the EPS-LD unit until th e unit is properly grounded at the electrical outlet and the redundant power supply cord is connected.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 180 Connecting the EPS-LD to Power An AC input power cord is not pr ovided with the EPS-LD. For information about power cor d requir ements, see “Selecting Power Supply Cords” on page 218 .
Summit Family Switches Hardware Inst allation Guide 181 NOTE An AC power cord is not provided with the EPS-500 unit. See “Selecting Power Supply Cor ds” on page 218 for information about selecting a power cord.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 182 Connecting the EPS- 500 Power Supply CAUTION Do not attach the AC power cord to the EPS-500 unit until the unit is properly grounded at the electrical outlet and the redundant power cord is connected.
Summit Family Switches Hardware Inst allation Guide 183 3 Connect an appropriate AC input power cor d to the AC connector on the EPS-500 unit. NOTE An AC power cord is not provi d ed with the EPS-500 unit. See “Selecting Power Supply Cords” on page 218 for information about selecting a power cord.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 184 NOTE For centralized DC power connection, th is product is intended to be inst alled in restricted a.
Summit Family Switches Hardware Inst allation Guide 185 Installing an EPS-15 0DC Power Supply NOTE Install the EPS-T2 before you b egin installing the EPS-150DC.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 186 Figure 157: Three-wire Cable Harness NOTE Each wire on the harness has been pr operly marked for proper attachment to the DC power source. Leave these labels on each lead wire for future reference.
Summit Family Switches Hardware Inst allation Guide 187 Figure 158: Connecting the Inpu t Cable to the EPS-150DC Unit 3 T ighten the retainer nut on the connector until it is finger tight.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 188 Figure 160: Connecting an EPS-150DC Unit to a Switch 7 Energize the DC circuit. The Power LED on the front of the EPS-150DC unit tu rns solid green to indicate that it is ready .
Summit Family Switches Hardware Inst allation Guide 189 T o disconnect and remove an EPS-150DC unit: 1 Attach the ESD strap t o your wrist and connect th e metal end to the gr ound receptacle on the top- right corner of the switch fr ont panel. 2 De-energize the DC cir cuit.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 190 Installing an EPS-C Chassis CAUTION Do not use the rack mount brackets to suspend the EPS-C fro m under a table top or desk, or to attach the EPS-C unit to a wall.
Summit Family Switches Hardware Inst allation Guide 191 c Repeat steps a and b for the other side of the EPS-C. 4 Slide the EPS-C into a 19-inch rack and secu re it using appropriate rack-mount screws. 5 Connect the keyed end of the redundant power cor d to the EPS-C (see Figur e 163 ).
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 192 Figure 164: Installing the EPS-600LS Unit in the EPS-C Chassis 3 Slide the unit completely into the chassis until the front of the EPS-600LS is flush with the surfa ce of the EPS-C (see Figure 165 ).
Summit Family Switches Hardware Inst allation Guide 193 NOTE An AC power cord is not provi ded with the EPS-600LS un it. See “Selecting Power Supply Cords” on page 218 for information about selecting a power cord. CAUTION The EPS-600LS uni t does not have a sw itch for turning the unit on and off.
Installing Summi t External Power Su pplies Summit Family Switches Hard ware Installation Guide 194.
Summit Family Switches Hardware Inst allation Guide 195 7 Summit Option Cards This chapter describes Summit option cards availabl e for use with Summit X350 series, X450 series, X450a series, and X450e series switches.
Summit Option Cards Summit Family Switches Hard ware Installation Guide 196 Safety Information CAUTION Pluggable optical modules may become very hot after prol onged use.
Summit Family Switches Hardware Inst allation Guide 197 Mixing ZR XENP AKs with Other T ypes Ta b l e 3 1 lists the supported combinations of XENP AK types using ZR XENP AKs in a Summit X450 series switch.
Summit Option Cards Summit Family Switches Hard ware Installation Guide 198 Figure 167: Summit XGM2-2xn Option Card NOTE Refer to the Extreme Networks Pluggable Inte rface Module s Installation Guide for more information about XENP AK modules.
Summit Family Switches Hardware Inst allation Guide 199 Figure 168: Summit XGM2-2xf Option Card NOTE Refer to the Extreme Networks Pluggable Inte rface Module s Installation Guide for more information about XFP modules.
Summit Option Cards Summit Family Switches Hard ware Installation Guide 200 Installing a Summit Port Option Card CAUTION Summit port option cards are not hot-swappable. Disconnect power to the switch bef ore installing or removing a Summit option card.
Summit Family Switches Hardware Inst allation Guide 201 Figure 170: Installing a Summit Port Option Card (XGM-2xn Shown) 5 Using the scr ews fr om the cover plate, secure th e option card to the back panel of the switch.
Summit Option Cards Summit Family Switches Hard ware Installation Guide 202.
Summit Family Switches Hardware Inst allation Guide 203 8 Maintenance Procedures for Summit X650 and Summit X480 Series Switches This chapter describes how to r eplace components in a S ummit X650 series switch.
Maintenance Proce dures for Summit X650 and Summi t X480 Series Switches Summit Family Switches Hard ware Installation Guide 204 Figure 171: Removing an AC PSU 4 Carefully slide the PSU the rest of the way out of the switch. CAUTION Power supplies may become very hot during operation.
Summit Family Switches Hardware Inst allation Guide 205 Replacing a Summit X650 DC Power Supply In a redundant power configuration, you can re place one Summit X650 DC PSU without powering down the switch.
Maintenance Proce dures for Summit X650 and Summi t X480 Series Switches Summit Family Switches Hard ware Installation Guide 206 Installing the Replacement PSU T o install a replacement Summit X650 DC PSU: 1 V erify that the PSU is right side up (see Figure 174 ) 2 Carefully slide the PSU all the wa y into the power supply bay (see Fi gure 174 ).
Summit Family Switches Hardware Inst allation Guide 207 Figure 175: Connecting th e Ground Wire Connecting the DC Power Cables T o connect the DC power cables to the Summit X650 DC PSU: 1 V erify that the DC circuit is de-energized.
Maintenance Proce dures for Summit X650 and Summi t X480 Series Switches Summit Family Switches Hard ware Installation Guide 208 Figure 176: Connecting the D C Power Cables (Part 1 ) d T ighten both screws on the terminal block to 1 1 inch-pounds ( Figure 178 ).
Summit Family Switches Hardware Inst allation Guide 209 Figure 177: Connecting the D C Power Cables (Part 2 ) 6 Energize the DC circuit. SH_1 12 (+) (–) RTN -48V.
Maintenance Proce dures for Summit X650 and Summi t X480 Series Switches Summit Family Switches Hard ware Installation Guide 210 Replacing a Summit X480/X650 Fan Module The procedur e for replacing a fan module is the sa m e f o r e i t h e r a S u m m i t X 4 8 0 s e r i e s s w i t c h o r a Summit X650 series switch.
Summit Family Switches Hardware Inst allation Guide 211 Replacing a V ersatile Interface Module (VIM) The procedur e for replacing a VIM is the same for both the VIM1 module in the Summit X650 serie s switch and the VIM2 module in the Summit X480 series switch.
Maintenance Proce dures for Summit X650 and Summi t X480 Series Switches Summit Family Switches Hard ware Installation Guide 212 5 Install the replacement VIM in the sw itch ( Figure 181 ): a Make sure the inserter/ejector le vers are r otated down.
3 Appendices.
.
Summit Family Switches Hardware Inst allation Guide 215 A Safety Information WAR NI NG ! Read the following safety information th oroughly before installing Extreme Netw orks products. Failure to follow this safety information can lead to personal injury or damage to the equipment.
Safety Infor mation Summit Family Switches Hard ware Installation Guide 216 Installing External Power Supply Units For the ratings and power r equiremen ts of each power supply un it, see Appendix B, “T echnical Specifications” or the da ta sheet for the power s upply at http://www .
Summit Family Switches Hardware Inst allation Guide 217 Maintenance Safety When you perform maintenance procedur es on Extreme Networks equipment, follow these recommendations: ● Use only original accessories or components approv ed for use with this system.
Safety Infor mation Summit Family Switches Hard ware Installation Guide 218 This equipment can be connected between buildings if any one of the followi ng conditions is true: ● Cable runs between buildings are less then 140 feet long. ● Cable runs between buildings ar e directly buried.
Summit Family Switches Hardware Inst allation Guide 219 WAR NI NG ! When using multiple power supplies, make sure that each power supply is attached to an independent circuit breaker . See the installation instructions for the po wer supply for proper si zing of circuit breaker .
Safety Infor mation Summit Family Switches Hard ware Installation Guide 220 WAR NI NG ! When working with laser optic modules , always take the following prec auti ons to avoid exposure to hazardous radiation. ● Never look at the transmit LED/laser through a magnifying device while it is powered on.
Summit Family Switches Hardware Inst allation Guide 221 Sicherheitshinweise WARNU NG! V or der Installation der Produkte von Extreme Networks sind die nachfolgenden Sicher heitshinweise aufmerksam zu lesen. Die Nichtbeachtung dieser Sich erheitshinweise kann zu V erletzungen od er Schäden an der Ausrü stung führen.
Safety Infor mation Summit Family Switches Hard ware Installation Guide 222 jede empfangene Interfer enz zulassen, einschließlich einer Interfer enz, die einen unerwünschten Betrieb verursachen kann.
Summit Family Switches Hardware Inst allation Guide 223 325 W AC Netzteil wird durch das Ziehen des Netzkabels unterbrochen. Es ist sicherzustellen das diese V erbindung leicht zugänglich ist.
Safety Infor mation Summit Family Switches Hard ware Installation Guide 224 ● V erlegen von Kabeln: Kabel so verlegen, d ass kein e Schäden entstehen oder Unfälle, z.
Summit Family Switches Hardware Inst allation Guide 225 ● Japan: ■ V ersorgungssteckdose, 15 A, JIS 8303 für 1 1 0/220-V AC-Net zteile. ■ Das mit dem Netzteil, dem Switch oder der Gr un dplatte.
Safety Infor mation Summit Family Switches Hard ware Installation Guide 226 Einhaltung behördlicher V orschriften durch SFP (Mini-GBIC), XENP AK und XFP ● Laserprodukt der Kl asse 1 ● EN60825-1+A.
Summit Family Switches Hardware Inst allation Guide 227 B T echnical Specifications This appendix include s the following specific ations for Summit switch series and related components: ● Summit X1.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 228 Packaged Dimensions Summit X150-24t switch Summit X150-24p switch Height: 12.6 inches (32 cm) Width: 23.6 inches (60 cm) Depth: 18.5 inches (47 cm) Summit X150-48t switch Heig ht: 12.
Summit Family Switches Hardware Inst allation Guide 229 Power consumption (Watts) 500 Summit X150-48t Power Operational voltage range 90 to 264 V Nominal input ratings 100 to 240 V , 50/60 Hz, 1.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 230 Country-specific VCCI Cla ss A (Japan Emissions) AS/NZS 3548 ACA (Austral ia Emissions) CNS 13438:1997 Clas s A (BSMI-.
Summit Family Switches Hardware Inst allation Guide 231 Summit X250e Series Switches The Summit X250e series includes the following switches: ● Summit X250e-24t switch ● Summit X250e-24tDC switch .
Technical Specific ations Summit Family Switches Hard ware Installation Guide 232 Summit X250e-24p switc h 14.9 lb (6.8 kg) Summit X250e-48t switch 15.
Summit Family Switches Hardware Inst allation Guide 233 Input current 0.6 A @ 115 V (low-line) 0.3 A @ 23 0 V (hig h-line) Line frequency ra nge 47 to 63 Hz Inrush current 30 A @ 115 V, 60 A @ 230 V P.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 234 Efficiency 78% Heat dissipation (Watt s) 31 Heat dissipation (BTU/hr) 105.8 Power consumption (Watts) 31 Power consumpti on (BTU/hr) 105.8 Summit X250e-48t Power Operational voltage range 90 to 264 V Nominal input ratings 100 to 240 V , 50/60 Hz, 1.
Summit Family Switches Hardware Inst allation Guide 235 Summit X250e-48tDC Power Operational voltage range -40 to -57.6 V Nominal input ratings -48 V , 2.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 236 Country-specific VCCI Class A (Japan Emissions) AS/NZS 3548 ACA (Austral ia Emissions) CNS 13438:1997 Clas s A (BSMI-T.
Summit Family Switches Hardware Inst allation Guide 237 Summit X350 Series Switches The Summit X350 series includes the following switches: ● Summit X350-24t ● Summit X350-48t T able 35: Summit X350 Series Sw itch T echnical Specifications Physical Dimensions Summit X350-24t switch Height : 1.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 238 Input current 1.45 A @ 115 V (low-line) 0.65 A @ 230 V (high-line) Line frequency ra nge 47 to 63 Hz Inrush current 30.
Summit Family Switches Hardware Inst allation Guide 239 IEEE 802.3 Media Access Standards IEEE 802.3ab 10 00BASE-T Environmental Data Environmental Standards EN/ETSI 300 019-2-1 v 2.1.2 - Class 1.2 Storage EN/ETSI 300 019-2-2 v2.1 .2 - Class 2.3 Transportation EN/ETSI 300 019-2-3 v 2.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 240 Summit X450 Series Switches The Summit X450 series includes the following switches: ● Summit X450-24t switch ● Sum.
Summit Family Switches Hardware Inst allation Guide 241 Country-specific VCCI Clas s A (Japan Emissions) AS/NZS 3548 ACA (A ustralia Emissions) CNS 13438:19 97 Class A (BSMI-Taiwan) MIC Mark, EMC Appr.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 242 Summit X450a Series Switches The Summit X450a series includ es the following switches: ● Summit X450a-24t swit ch .
Summit Family Switches Hardware Inst allation Guide 243 Power supply inpu t socket IEC 320 C14 Power cord input plug IEC 320 C13 Power cord wall plug Refer to “Selecting Power Supply Cords” on page 218 . Power supply cord gauge 18 AWG (0.75 mm 2 ) up to 6 feet or 2 meters or 16 AWG (1.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 244 Power supply input socket TYCO PN 206061-1 Summit X450a-24x Power & Acoustic Sound Operational voltage range 90 to 264 V Nominal input ratings 100 to 240 V , 50/60 Hz, 1.
Summit Family Switches Hardware Inst allation Guide 245 International EMC certific ations CISPR 22 :1997 Class A (International Emissions) CISPR 24:1997 Cl ass A (International Immunity) IEC/EN 61000-.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 246 Summit X450e Series Switches The Summit X450e series includes the following switches: ● Summit X450e-24p switch ● Summit X450e-48p switch T able 38: Summit X450e Series Switch T echnical Specifications Physical Dimensions Summit X450e-24p switch Height : 1.
Summit Family Switches Hardware Inst allation Guide 247 Power supply cord type AC Power supply inpu t socket IEC 320 C14 Power cord input plug IEC 320 C13 Power cord wall plug Refer to “Selecting Power Supply Cords” on page 218 . Power supply cord gauge 18 AWG (0.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 248 Operating conditions Temperature range: 0° C to 40° C (32° F to 104° F) Humidity: 10% to 93% relati ve humidity, non-condensing Altitude: 0 to 3,000 meters (9,850 feet) Shock (half sine): 30 m/s 2 (3 g), 11 ms, 60 shocks Random vibration: 3 to 500 Hz @ 1.
Summit Family Switches Hardware Inst allation Guide 249 Summit X480 Series Switches The Summit X480 series includes the following switches: ● Summit X480-24x switch ● Summit X480-48x switch ● Su.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 250 Summit X480-24x with VIM2-Summi tStack Module (AC Power Supply) Nominal input ratings 100 to 240 V , 50/60 Hz, 3.
Summit Family Switches Hardware Inst allation Guide 251 Input current 2.3 A @ 100 V (low-line) 1.0 A @ 240 V (high-line) Heat dissipation, Watts, BTU 227 W, 774 BTU/hr Power consumption, Watts, BTU 227 W, 774 BTU/hr Summit X480-48x with No Installed VIM (DC Power Supply) Nominal input ratings 48 V , 8.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 252 Power consumption, Watts, BTU 148 W, 503 BTU/hr Summit X480-48t with VIM2-Summi tStack Module (DC Power Supply) Nominal input ratings 48 V , 7.0 A Input current 3.24 A @ 48 V (low-line) 2.
Summit Family Switches Hardware Inst allation Guide 253 Summit X480 Power Supplies The following two Summit X480 power supplies are available for use in the Summit X480 s eries switches: ● Summit X480 AC PS U ● Summit X480 DC PSU Environmental Data Environmental standards EN/ETSI 300 019-2-1 v2.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 254 Power supply cord gauge 18 AWG (0.75 mm 2 ) up to 6 feet or 2 meters or 16 AWG (1.
Summit Family Switches Hardware Inst allation Guide 255 Summit X650 Series Switches The Summit X650 series includes the following switches: ● Summit X650-24t switch ● Summit X650-24x switch T able 42: Summit X650 Series Sw itch T echnical Specifications Physical Dimensions Summit X650-24t switch Summit X650-24x switch Height: 1.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 256 Heat dissipation, Watts, BTU 617 W, 2,105 BTU/hr Power consumption, Watts, BTU 617 W, 2,10 5 BTU/hr Summit X650-24t with VIM1-1 0G8X Module (DC Power Supply) Nominal input ratings 48 to 60 V , 24 A Input current 14.
Summit Family Switches Hardware Inst allation Guide 257 Summit X650-24t with VIM1-SummitS tack512 Module (DC Power Supply) Nominal input ratings 48 to 60 V , 24 A Input current 10.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 258 Safety Standards North American Safety of ITE UL 6095 0-1:2003 1st Ed., Listed Device (US) CSA 22.2#609 50-1-03 1st Ed.(Canada) Complies with FCC 21CFR 10 40.10 (US Laser Safe ty) CDRH Letter of Approval (US FDA Approval) IEEE 802.
Summit Family Switches Hardware Inst allation Guide 259 Storage & transportation conditions (packaged) Transportation temperature: -40° C to 70° C (-40° F to 158° F) Storage and transportation.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 260 Summit X650 Power Supplies The Summit X650 power supplies can be used in th e Summit X650-24t switch and the Su mmit X650-24x switch.
Summit Family Switches Hardware Inst allation Guide 261 Summit External Power Supplies The following external power supplies are available fo r use with Summit X159 se ries, X250e series, X450 series,.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 262 Ta b l e 4 7 shows the wire-to-pin connections for the conne ctor on the r ear panel of the EPS-160 power supply .
Summit Family Switches Hardware Inst allation Guide 263 Heat dissipation, W atts, BTU/hr 158 W, 539.1 BTU/hr Power consumption, Watts , BTU/hr 659 W, 2248.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 264 T able 49: EPS-600LS External Power Module (Model 10913) For use with the Summit X450 e-48p and X250e-48p switches Mus.
Summit Family Switches Hardware Inst allation Guide 265 Ta b l e 5 1 provides the wire-to-pin connection specificatio ns for the DC wiring harness shipped with the EPS-150DC power supply .
Technical Specific ations Summit Family Switches Hard ware Installation Guide 266 Console Connector Pinouts This section provides conne ctor pinouts fo r the console port and associated cables. Ta b l e 5 2 describes the pinouts for a DB-9 console plug connector .
Summit Family Switches Hardware Inst allation Guide 267 Figure 184 shows the pinouts for a 9-pin to 9- pin (PC-A T) null-modem serial cable. Figure 184: PC-A T Serial Null-modem Cable Pinouts Screen T.
Technical Specific ations Summit Family Switches Hard ware Installation Guide 268.
Summit Family Switches Hardware Installa tion Guide 269 Index Numerics 10GBASE-T ports, 169 A amperage, calculating for UPS, 94 ANSI standards, 95 automatic failover, setting up, 16 B bend radius, 89 , 90 BICSI standards, 88 building cod es, 84 Building Industry Cons ulting Service Internation al.
Index Summit Family Switches Hard ware Installation Guide 270 features , 76 installing, 183 specifications, 265 with Summit X250e-24tDC switch, 24 with Summit X450a-24tDC switch, 47 with Summit X450a-.
Index Summit Family Switches Hardware Installa tion Guide 271 M management port in a stacked configuration, 118 Summit X150 series swit ches, 17 Summit X250e seri es switches, 22 Summit X350 series sw.
Index Summit Family Switches Hard ware Installation Guide 272 signal quality and RF interference, 92 site planning process, 83 slack in cable, 89 slot number in a stack, 98 space requirements, rack, 8.
Index Summit Family Switches Hardware Installa tion Guide 273 Summit X450e-24p switch, 54 Summit X450e-48p switch, 56 Summit X480 AC power supply specifications, 253 Summit X480 power supp ly features.
Index Summit Family Switches Hard ware Installation Guide 274 XGM2-2xn optio n card, 197 XGM-2xn op tion card, 196.
Ein wichtiger Punkt beim Kauf des Geräts Extreme Networks 17001 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Extreme Networks 17001 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Extreme Networks 17001 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Extreme Networks 17001 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Extreme Networks 17001 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Extreme Networks 17001 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Extreme Networks 17001 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Extreme Networks 17001. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Extreme Networks 17001 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
