Benutzeranleitung / Produktwartung SEPG04002 des Produzenten Epson
Zur Seite of 565
EPSON AcuLaser C1100 A4 Full Color Laser Printer SERVICE MANUAL SEPG04002.
Notice: All rig hts reser ved. No part of th is manual may be reprodu ced, st ored in a r etrieva l system, o r transmi tted in a ny form or by a ny means, elect ronic , mechanica l, photoco pying, reco rding, or otherwi se, without the pr ior writ ten permis sion o f SEIKO EPSON CORPORATION.
PRECAUTIONS Precaut ionary not atio ns througho ut the text are categ orized re lati ve to 1)Pe rsonal in jury a nd 2) dama ge to equi pment. DANGER Signals a prec aution whic h, if igno red, co uld res ult in s erious or fatal personal inju ry. Great c autio n should be exerci sed in p erf ormi ng procedur es preced ed by DANGER Headi ngs.
About This Manual This manual descr ibes basic functio ns, theory of electrical and m echa nical operations, main tenance and repair p rocedures of the printer. The instructions and procedures included herein are intend ed for the exper ienced re pair tech nicians, and attention sho uld be giv en to the pr ecautions on the precedin g p ag e.
Abbreviations The follo wing is a rep resentat ive example of abbreviat ions (bot h origin al and commo n ones) us ed in thi s manual. ADC ............. .. Automatic Density Contro l AG ... ................. ............ .... Analog Ground APS .......
Safety Information To prevent accid ents during a m aintenance procedur e, strictly ob se rve the Warnings and Cautions and never depar t from the in str uctions given in this do cument. Do not d o anything that is dan gerous even if not specifically described i n this manual .
High T em peratu re As sembly When working with hot parts (FUSER etc.) mak e sure to turn the power off, un plug the power cable, and leave the printer until it cools down sufficiently to work with to prevent bur n inju ry.
Lase r Beam W ARNI NG Letting a laser beam get into your eye directly could res ult in loss of visi on. Never open the Cover where the Warning Label About Laser Beam is affix ed. Before disassembling or assembling, be sure to turn the power off.
W arning/C aution Labels Warning labels and caution labels are attached on the corr espond ing locatio ns on or in the printer . Caution Label About H igh-tempera ture Surface The labels are attached on the Fuser assy and the perimeter alerting the u ser to avoid b urn injur y.
Cautions relat ing to T one r cleaning To prevent ignition, ex plosion, burn, injury, etc., d o not use a g eneral vacuum cleaner for cleaning dropped ton er.
Safety Devices Use extra care when checking or servicing the safety devices (e.g., interlock switches, fuses, thermost at). The printer's cov er, control panel an d any othe r parts which are directly related to the u ser's safety should also be observed carefully.
Schematic Diagr am of Safety System Leg_Sec001_025EA.
Revision S tatus Revision Date o f Issue Descript ion A 28 Sep tember , 200 4 First release B 1 3 J U L Y , 20 0 5 <Mo d i f i ca t i o n> Chapter 1: • Tabl e 1-2 C olor m ode (U nit : se cond s or les s) (p. 23) / Modification • Supporte d paper s ize, type and orientat ion (p.
EPSON AcuLaser C110 0 Rev is io n B 14 Contents Chapter 1 PRODUC T DESCRIPTION 1.1 Overview .......... ........... ................. ............ ........... ................. ........... ........... ......... 20 1.1.1 Engine featu res ...............
EPSON AcuLaser C110 0 Rev is io n B 15 1.16.4 W arning Messages an d Troublesho oting................... ........... ........... ......... 62 1.16.5 Serv ice Call Error Mess ages ..................... ........... ................. ........... ........
EPSON AcuLaser C110 0 Rev is io n B 16 3.6.2 Printing Procedu re of Test Pr int Pattern ...................... ........... ................. . 274 Chapter 4 DISASSEMBLY AND ASSEMBLY 4.1 Overview .......... ........... ................. ............ ..
EPSON AcuLaser C110 0 Rev is io n B 17 4.6.8 LATCH ASSY AD ......... ................. ........... ........... ................. ........... ....... 372 4.6.9 BCR CLN XERO ASSY ........... ........... ................. ........... ............ .......
EPSON AcuLaser C110 0 Rev is io n B 18 4.13.14 MOTOR ASSY FEEDER...... ................. ........... ........... ............ ............ 460 4.13.15 CLUTC H ASSY FEED ......... ................. ........... ........... ................. ....... 461 4.
CHAPTER 1 PRODUCT DESCRIPTION.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Overview 20 1.1 Overview This printer is a conven tional 4-cycle color p age printer that takes advantage of laser and electropho tographic technologi es.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 21 1.2 Basic Spe cifications 1.2.1 Process Spe cificati ons & System Printing method : Semiconductor laser beam sc.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 22 PRINTING MO DE BY PAPER TYPE Table 1-1. Printing mode by pa per t ype Paper type Prin ting spee d mo de F/C B/W Plain p aper 64 to 80g/m 2 (RX-8 0/4024) Standa rd Standard Plain p aper (Bac k) For re verse side of paper when feed ing manu ally to print on both sid es.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 23 FIRST PRIN T TIME The time from r eceiving the Start command to when trailing edg e of the paper leav es the paper eject roller. Note that the time given in th e tables below does not apply when the printer is in the conditions descri bed in “1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 24 PAPER FEED REFERENCE Reference po sition to feed paper (in any size) is always center of the feede rs. PAPER FEED Note *1 : Refer to “1.3 Paper Specifications ” (p30) .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 25 SUPPORTED PAPER SIZE, TY PE AND ORIE NTATION Note *1 : Pape r su ppo rted on ly by contr oller f irmw are (ha ndled as us er de fined size by the vide o I/F) *2 : For the ori entatio n of en velope s, r efer to “Envelope orie ntation ” (p.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 26 Envelope orientation NOTE 1: Set envelo pe s with its print su rface faci ng up 2: Image qual ity and feed is not guarant eed when printing on the b ack side (flap side) of enve lopes.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 27 Dimensions and weight wit h options installed NOTE 1: Manufacturin g tolerance is ± 5 mm in dimens ions and ± 0.5 kg in weight . 2: Consumables are not includ ed in the main unit weig ht (incl uding co ntroller).
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 28 CONSUMABLE S AND PE RIODIC REPLACEM ENT UNIT NOTE: For detailed specificatio ns, refer to “1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Basic Spe cifications 29 NOISE Sound pres su re NOTE 1: The metho d of measur ing a nd ca lculatio n con forms to IS O-77 79. 2: Values ment i oned above are ac tual measurem ent value. Sound power NOTE 1: The metho d of measur ing a nd ca lculatio n con forms to IS O-77 79.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Paper Speci ficati ons 30 1.3 Paper Specifications 1.3.1 Paper T ype Standa rd paper Monochrome: RX-80 paper (monoch rome), 4024 paper (.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Paper Speci ficati ons 31 1.3.3 Avail able Paper by Feeder Note : { : Paper feed an d image quali ty is guaranteed. : Paper fe ed and pri nting is possible. However, th is is limit ed to type s of paper for gene ral applicatio ns.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Reliabil ity and Ser viceabil ity 32 1.4 Reliability a nd Serviceability 1.4.1 Reliability MECHANICAL L IFE TI ME Main unit: Color:Mo nochrome = 2:1 : 200, 000 page s or 5 years , whichever comes firs t.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Reliabil ity and Ser viceabil ity 33 SKEW HEIGHT OF CURL OF OUTPUT PAPER NOTE 1: Th e same for simpl ex and duplex printing 1.4.2 D urability PRINT VOLUME (PAGES/MONTH) Average : 3, 00 0 pages/m onth Maximum : 30, 0 00 pages/ month 1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Service Co nditions 34 1.5 Service Conditions 1.5.1 Ambient Temperature and Humidit y 1.5.2 Air Pressure (Altitude) 65 to 101kPa (0 to 3, 100 m or le ss) 1.5.3 Levelness Difference b etween fr ont and back: 5mm or l ess (at 445mm ) Difference between left and right: 10mm or less (at 445mm) 1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Conditio ns for Stor age and Tr ansport 35 1.6 Conditions for St orage and Transport 1.6.1 Ambient Temperature and Humidit y Note *1 : N on-conde nsing 1.6.2 Storage Altitude 0 to 3, 1 00 m or less For ai r t rans port, 0 to 15, 000 m.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Electric al Characte ristics 36 1.7 Elect rical Characteristics NOTE: The following sections do not incl ude any optional units. 1.7.1 Electrical Fast Transient /Bursts (AC Line Noise) Ensure t he followi ng condi tions usi ng evaluati on metho ds complian t with IEC 61000- 4-4.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Compatibl e Specificatio n 37 1.8 Compatible Specif i cat ion 1.8.1 Safety Standard 1.8.2 Safety Standard (Laser Transmi ssion) NOTE: <Reference> Laser sp ecifica tions Wavelength ( shortes t to longes t) : 770 to 7 90nm Maxim u m aver age ra diant po wer : 5 mW 1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Consumables/Pe riodic re placement un it 38 1.9 Consumables/Periodic replacement unit 1.9.1 Specificatio ns Note *1 : Appro ximate numb er of p rinted pages using A4 con tinuous prin ting at 5% im age occupa tio n rate.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Consumables/Pe riodic re placement un it 39 1.9.2 Condi tions for Storage and Transport Temperature and humidity conditions Note *1 : N on-conde nsing Note : Storage time afte r opening is 12 mont hs in the n ormal oper ating en vironmen t.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION External Appearance a nd Unit Names 40 1.10 External Appearance and Unit Na mes 1.10.1 Unit names Figure 1-8. U nit name_1 Figure 1-9. Un it name_2 Table 1- 30. Li st of u nit na mes No. Name No.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION External Appearance a nd Unit Names 41 Figur e 1-10 . Unit na me_3 Figur e 1-11 . Unit na me_4 Figu re 1-12 .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Engine Restric tions 42 1.11 Engine Restrictions FACTORS LIMITIN G PRINTI NG SPEED Image quality adjustment Note *1 : Condition to print 50 copies (p ages) contin uously: l The average of the pri n t ratio should be 60 % o r less for each color.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Engine Restric tions 43 FACTORS LIMITIN G PRINTI NG START Note *1 : When th e operati on p erforme d during the warm-up , the warm-up ti me becomes 74 seconds. *2 : The war m-up ti m e i s includ ed .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Notes When Replacing Cons umables a nd Install ing Optiona l Products 44 1.12 Notes Wh en Replacin g Consumables and Installing Optional Products 1.12.1 Consuma bles Toner Cartridge The power supply of the main uni t should b e on.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Life detail s 45 1.13 Life d etails Monochrome mod e Note : B:Monochr ome C:Colo r Note *1 : 1. The life of a Photocond uctor Unit may n ot reach the abo ve numerical value ac cording to an op erating cond ition.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Controller Sp ecificat ions 46 1.14 Con troller Specific ations 1.14.1 Controll er Basic Specifications CPU : VR430 5 (66.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Controller Sp ecificat ions 47 1.14.3 Ex ternal Interface Specifications The printer pr ovides the following ho st interfaces. Parallel (IEEE1284 compliant) interface : Standard USB (Rev.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 48 1.15 Control P anel 1.15.1 Ex ternal Appearance a nd Names Figure 1-14. Exte rnal View of Control Panel Table 1-36 . Indi cators Indicato rs Functi on LCD 1 line x 20 cha rac ters (5 x 7 dot mat rix ) Ready LED O n : P rint er is r e ady to prin t.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 49 1.15.2 Panel Settings List The printer settings are listed below. Underlined value in the Setting value column are factory default sett ings.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 50 Setup Menu Note *1 : This item exists a s the para meter, but n ot di splayed on the pane l.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 51 USB Menu Note *1 : After this item is changed , the setting value takes effect after a warm bo ot or after the power is turned o n again.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 52 PRI N T E R AD JU ST MEN U Note *1 : Display ed o nly when the Sup po rt Mode has been selected by a sp eci al operation when the power is turned on. After changing the setting s in the Printer Adjust Menu and pressing the Enter button, the printer reboots.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 53 USER SETTING IT EMS OTHER THAN IN THE SETTI NG ME NU The following is a list of user settings not included in the Setup menu . Initialization by the Initialization menu of the Panel does not clear these item s.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 54 1.15.3 Ex planation of Menu and Settings The following are items specific to this printer. Reset menu Chan ge Tone r C/Ch ange T oner M /Chan ge Tone r Y/C hange T oner K Used when rep lacing a Toner Cartridge befor e toner end occur s.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Control Panel 55 1.15.4 Specia l Operations LIST OF OPERATING FUNCTIONS The following is a list of the special operating functions sup por ted by this prin ter. Do not m ake these funct ions (except Suppor t mode and panel sett ing value initialization) available to users.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 56 1.16 Printer Stat us 1.16.1 Li st of Printer Mess ages The following is a list of messages displayed by the printer.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 57 Note *1 : W W W W W=C, D, E, F , G, DM, MP, LC *2 : Can cel Print Jo b and C ancel All P rint Job using th e ope ration pa nel. *3 : Cancel Print Job u sing the host. *4 : For de tailed information on respondi ng to c omposite erro rs, refer to th e print status area.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 58 1.16.3 Error Mess ages and Troubleshooting The following are items specific to this printer.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 59 NonGenuine To ner uuuu Explanation A non- genuine Toner C artridg e is instal led. Remed y Open cover A, install the right Toner Cartridge. The printer reco vers from th e error when the co ver is closed.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 60 Manual Feed ssss Explanation Manual feed mode is specified for the cu rrent print job. During p rinting i n the manual feed mode, t he paper ran ou t. Remed y Press the Start/ Sto p button.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 61 Invalid N/W Module Explanation The networ k progr am does not exist, o r a network program that is not fo r this printer is written. The interfaces m aintain the status befo re the error.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 62 1.16.4 Warni ng Messages a nd Troubleshooting The following are items specific to this printer. Worn Fuser Explanation The FUSER ASSY comes to near end of its life. The print quality is not guaranteed from now on.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 63 1.16.5 Servi ce Call Error Messages This section shows the service call error message of this printer. (For details, refer to Chapter3 “TROU BLESHOOTING” .) ENGINE -RELA TED SE RVICE CA LL ER RORS CONTROLLER-RELAT ED SERVICE CALL ERR ORS Table 1-40.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Printer St atus 64 1021 RAM error (slot 1) 1120 ROM checksum erro r (bit 0 to 7 ) (program) 1121 ROM checksum erro r (bit 8 to 1 5) (program) 11.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Expanding the RAM 65 1.17 Expanding t he RAM When the memory is insufficient, the printer displays the foll owing error messages. Mem Overflow Duple x Me m Overf low Image Optimum The following meth ods can be u sed to clear the errors .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Handling Prec autions 66 1.18 Handling P recautions 1.18.1 Precauti ons When Turning O ff the Power This printer includes internal, nonvolatile memory (EEPROM), which stores setting values important to operate the printer normally.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Status Shee t 67 1.19 Status Sh eet There are two kinds of status sheet, the Status Sheet (Simplified versio n) and the Status Sheet. Status Sheet (Si mplified version) : This can be p rinted us ing the prin ter operat ion panel.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Status Shee t 68 HARDWARE EN VIRONM ENT EXCEPT FOR OPTION 1. Serial No . : Serial number of the unit 2. Firm ware Revis ion : 211XX is indic ated. CONSUMABLE INFORM ATION AND PART NUMB ER NOTE: The first one is the part number of 1.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Status Shee t 69 Figure 1-16. Status Sheet (F ull version) Information Part Numbers T oner Cartridge Cyan Needed Soon E .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Engine St atus Sheet 70 1.20 En gine Status Sheet It can be output fro m the Mainte nance Menu. Fo r details , refer to Chapter6 “MAINTENANCE” for the Engine Status Sheet. C A U T I O N Do not disclose this inform atio n to the user.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Recommended Oper ating Envir onment (Host PC) 71 1.21 Recommended Operating Environment (Host PC ) Minimum req uirement s for Wi ndows OS : Wi ndow s ® 95/98/Me/20 00/XP, Win dows NT ® 4.
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Paper Handli ng Algorith m 72 1.22 Paper Handling Algorithm The relati onship betw een paper type, type and s ize is shown b elow .
EPSON AcuLaser C110 0 Rev is io n B PRODUCT DESCRIPTION Paper Handli ng Algorith m 73 Note *1 : Paper Type in Sele ct ype for each paper feed er PAPER SOURCE Note : For paper size ot h er than the abo.
CHAPTER 2 OPERATING P RINCIPLES.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 75 2.1 Pr int Pro cess 2.1.1 Print Process Overvi ew This printer is a “full color laser printer” th at uses the pr inciple of electrophoto graphic recordin g.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 76 2.1.2 Print Process Diagra m The diagram below illustrates the entire print pr ocess.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 77 2.1.3 T echnical Expl anation of Print Pro cess 2.1.3.1 Charging At the “Charging” pro cess, BCR (Bias C harge Roll) applies a un iform nega tive potential to the drum which rotates at a fixed speed .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 78 2.1.3.2 Exposure At the “Exposure” proces s, a laser beam is applied to the negatively charged surface of the drum to f orm an invisible electro static latent image onto the drum.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 79 2.1.3.3 Developing At the “Developing” proces s, toner is electri cally applied to the invisible electrostatic latent image on the d rum, to form a visivle image on it.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 80 Toner in the Dev eloper Assy is cons umed as the n umber of pr ints increases. To maintain t he approp riate developm ent densi ty, the equi valent amou nt of cons umed tone r mus t be re pleni shed to the Dev e loper Ass y f rom t he To ner C artri dge .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 81 2.1.3.4 Primary transfer (Drum → Belt) At the “Primary transf er” process, the to ner imag e formed on the drum surface is transferred to the B elt surface in Photoco nductor Unit by 1st BTR (First Bias Transfer Roll).
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 82 2.1.3.5 Cleaning (drum) At the “Cleaning (d rum)” process, r esidual toner is removed from the drum surf ace. Cleaning the drum Toner that was not transferred to the Belt at the “Primary transfer” proces s remains on the drum surface.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 83 2.1.3.6 Repeat (formation of complete t oner image) At the “Repeat (formation of complete toner image)” proces s, th e to ne.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 84 2.1.3.7 Secondary transfer (Belt → Pap er) At the “Secondary tran sfer” process, the co m plete toner image formed on the Belt surface is trans ferred to paper by the 2nd B TR (Second Bias Transfer Roll).
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Print Proces s 85 2.1.3.8 Discharging At the “Discharging” process, the charge on the paper is neutralized /removed by the Detack Saw.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES F low of Print Data 86 2.2 Flo w of Print Dat a 2.2.1 Da ta Flow Print data (electric signals) from the Printer Controller follows the flow show n below to become a pr int image.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 87 2.3 Drive Tran smissi on Pat h 2.3.1 DR IVE ASSY FEED Rotation of DRIVE ASSY FEED is tran smitted as follows: Figure 2-19 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 88 2.3.2 MO TOR ASSY P/R, DR IVE ASSY PRO Rotation of MOTOR AS SY P/R and DRIVE ASSY PRO is transm itted as follows: Figure 2-21 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 89 2.3.3 MO TOR ASSY MAG, MOTOR ASSY RO T Rotation of MOTOR ASSY MAG an d MOTOR ASSY ROT is transmitt ed as follo ws: Figure 2-23 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 90 2.3.4 MO TOR ASSY DUP Rotation of MOTOR ASSY DUP is transmitted as follows: Figure 2-25 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 91 2.3.5 MO TOR ASSY FSR Rotation of MOTOR AS SY FSR is transmitt ed as follows: Figure 2-27 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Drive Tra nsmission Pat h 92 2.3.6 MO TOR-PH Rotation of MOTOR-PH is transmitted as follows: Figure 2-29 .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 93 2.4 Paper Feed This section explains and illust rates the main functional compon ents that make up the paper feed s ection. The components are divided into four blocks as fo llows based on the basic configurati o n.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 94 2.4.1 MSI (Multi Sheet Inserter) MAIN FUNCTIONS GUIDE SIDE L/GUIDE ASSY SIDE R GUIDE SIDE L and GUIDE ASSY SIDE R move crossways of the paper feed direction, a nd tr ue up the left a nd right edges of sheets of pap er.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 95 2.4.2 Reg istration & FUSER MAIN FUNCTIONS CLUTCH ASSY PRE REGI The drive from the MOTOR-PH is transmitted to the ROLL ASSY-PRE REGI, and paper i s fed to t he registra tion section.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 96 2.4.2.1 Adjusting the leading edge of the paper If paper is fed up to the toner transf er section from the tray or cass ette without adjusting the alignment of the paper, the im age sometimes cannot be transferred at the correct position.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 97 2.4.3 5 00 Paper Feeder MAIN FUNCTIONS CONNECTOR (H ARNESS-ASSY FEED1) This is used for performing communications with the main unit and supplying power to the Paper Feeder. PWBA TRAY 500 Control s Motors and Sensors i n the 500 P aper Feed er.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 98 SOLENOID FEED The SOLENOID FEED controls rotation of the Feed Gear. When the SOLENOID FEED turns ON, the Feed Gear is un lock ed and Feed Roll rotates. T he SOLENOID FEED is repeatedly turned ON/OFF each time a sheet is fed to control the feeding timing.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Paper Feed 99 2.4.4 Dupl ex MAIN FUNCTIONS SWITCH-DUP DOOR The SWITCH-DUP DOOR detects whether the Duplex door is opened or closed. SOLENOID ASSY DUP The SELENOID ASSY DUP switches the gate inside th e Fuser.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 100 2.5 Xerogra phic This section explains and illustrates the main functional components that consist of the Xerographi c. The Xerog raphic is di vided into t he followi ng four b locks based on the bas ic configurat ion.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 101 2.5.1 RO S MAIN FUNCTIONS ROS ASSY ROS ASSY (Raster Output Scanner Assemb ly) is the exposur e unit that outputs the laser b eam to make the electros tatic latent image on the drum surface.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 102 2.5.2 P hotoconductor Unit MAIN FUNCTIONS Photoconductor Unit consists of the Belt, Belt Cleaner, Drum, Drum Cleaner, 1st BTR, and Waste Toner B oxes for each cleaner .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 103 SENSOR TNER FULL SENSOR TNER FULL detects the full s tate of the Waste To ner Box. Toner remaining on the dr um is s craped off by the Cleani ng Blade, and co llected i n the Waste Ton er Box.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 104 2.5.3 Dev elopment MAIN FUNCTIONS The Rotary Developer consists of four (f our colors) Toner Cartridges, ANTENNA CTRG, HOUSING ASSY-DEVE, and FRA ME AS SY R OTARY.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 105 Dispense Clutch (I nside the MOT ASSY MAG) The Dispense Clutch is provided to transmit the drive of MOT ASSY MAG to rotate the Augers for supplying toner. MOT ASSY MAG The MOT ASSY MAG rotates the Magnet Roll in the HOU SING ASSY-DEVE.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Xerographic 106 2.5.4 Second B TR & FUSER MAIN FUNCTIONS 2ND BTR ASSY The Second BTR (2 ND BTR ASSY) is a conductive roll. I t contacts the back of pape r (bac k of the s ide to be pr i nted o n) and a volta g e is ap plie d from t he HV PS.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Electri cal 107 2.6 Electrical This section explains and illust rates the main functional com pon ents making up the Electrical system. MAIN FUNCTIONS PWBA MCU PWBA MCU pe rforms communication with the printer co ntroller, and controls the parts to pe rfor m pri nt ing op era tions .
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Electri cal 108 PWBA E SS (P rint e r con tro l ler) PWBA ESS converts the print data is input via the network, USB, parallel ports, or other interfaces, and performs communications with the computer.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Operating Modes 109 2.7 O perating Mo des The prin ter has the following six op erating modes : WARM UP mode : The printer is warming up (until the printer is ready for printing). READY mode : The printer has finis hed the warm- up and is ready for printing.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Control 110 2.8 Control 2.8.1 Paper size control As this printer do es not hav e switche s, etc. for detecting paper size, only the pap er length is detected by S ENSOR REGI du ring paper feed. When the paper size d oes not match the print data, an error is sent to the controller.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Control 111 Execution Sequence of TC control 1. Adjustment of SENSOR ASSY ADC The SENSOR ASSY ADC has two LEDs, o ne for black and the other for color.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Control 112 Contro l of Tone r Cartri dge 1. Detect ion of Empt y stat us The judg ement of the Empty stat us of Ton er Cartri dges is mad e based o n toner patc h den sity value s (rea d by ADC senso r).
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Control 113 2.8.4 B elt position co ntrol In full color printing, positioning control of the images on the Belt is necessary so that the 4-color ton ers can be trans ferred to the same p osition to enable correct ov erlay of the 4-color ton ers.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Flying-s tart pri nting 114 2.9 Flying-start printing This pri nter improv es performan ce when prin ting full- color images by performi ng flying-start printing. Sequence 1) Th e printer starts printin g as soo n as it f inishes t o receiv e Yello w data of one pa ge.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Detecti on Mechanisms 115 2.10 Dete ction Mechanisms The follo wing shows a l ist of d etection f unctions.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Detecti on Mechanisms 116 Toner Cartridge New part detection Available CRUM Presence Det ect i on Available CRUM Color de tection Available CRUM Cannot be inco rrectly insta lled as the locatio n of t he holes are different for each color.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Principle of Electr ic Cir cuit Operat ion 117 2.11 Princ iple of Electric Circuit Operation 2.1 1.
EPSON AcuLaser C110 0 Revision B OPERATING PRINCIPLES Principle of Electr ic Cir cuit Operat ion 118 Figure 2-57 . C567MAIN Circuit B lock Diagra m Figure 2-58.
CHAPTER 3 TROUBLES HOOTING.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Procedure for t roubleshooti ng 120 3.1 Pr ocedure f or troubleshoo ting For efficient troubleshoo ting, verify the cond ition of the trouble carefully, and use FIP (Fault Isol ation Proced ures) and wiring conn ection diagr ams, and operating pri nciples.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Procedure for t roubleshooti ng 121 3.1.3 Precautio ns in Performing Troubleshooti ng Work 1. Be sure t o unplug the POWER CORD bef ore starting troubl eshooting work except whe n turning power ON is ne eded.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Procedure for t roubleshooti ng 122 3.1.4 Notes on Using FIP 1. The trouble shooti ng method describe d here assumes tha t there i s no malfunct ion in the print er contr oller (PWBA ESS).
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Procedure for t roubleshooti ng 123 3.1. 5 Warmin g- Up Flow chart at Po wer-ON The following flowchart (outline) shows the printer’s warm-up operation, fr om power-on to when the printer is ready to print.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP 124 3.2 FIP 3.2.1 Ou tline FIP is provided as the first step to identify the cause of trouble. FIP is a guide for proceeding with tr oubleshooting while check ing error codes and fo r various oth er symptoms of trou ble.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 125 3.3 FIP according to the printer message 3.3.1 List of Errors and Warnings ER ROR LIST RE LA TED TO PA PE R JA M Figure 3-3.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 126 Jam DM -- - SENSOR LOW PATH was ON at Power ON or when I/L was closed. (Sta tic Ja m) 38 (p.191) Jam C Jam D -- - SENSOR UPPER PATH was ON at Power ON or when I/L was closed.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 127 OTHER ERRORS AND WARNINGS Table 3-2. List of Errors and Warnings Class Panel Message Error LED Description See FIP Warnin g Y Toner Low --- The toner sup ply time of the Yellow toner ca rtridge has reached the preset ti me.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 128 Error TonerCart Error M ON A communication error occurred between PWBA MCU and ANTENNA CTRG (CRUM CTRIG). 14 (p.147) An error occurre d when writing da ta to ANTENNA CTRG (CRUM CTRIG).
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 129 Eeeor G Open ON Th e Cover of Tray 1 is open. 68 (p.226) DM Open ON Dup lex Co ver is ope n. 69 (p.227) D Open ON Dupl ex is op en. 70 (p.228) B Open ON CO VER TOP is o pen.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 130 3.3.2 List of Serv ice Request Table 3-3. List of Service Request Class Panel Messae g Descript ion See FIP Engin e Rel ated ( E ) Servi ce Re q E510 ROS Motor Failure 44 (p.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 131 Engine Relat ed ( E) Servi ce Re q E527 Deve Ho me P ositi on Sen sor Error 45 (p.198) PWBA MCU coul d not re ceive signals o utput from Rotary Home P osition Sen sor within th e specifie d time afte r rotation o f Rotary Develo per.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 132 Controller Related (C) Service Req C0017 CPU error (undefined in terruption) C1 (p .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 133 Controller Related (C) Service Req C0256 CPU error (divide by 0) C1 (p .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 134 3.3.3 Error Code FIP 3.3.3.1 Engine related error FIP-1 Panel Mess age Install Y TnrCart Possi.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 135 FIP-2 Panel Mess age Install M TnrC art Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 136 FIP-3 Panel Mess age Install C TnrCart Possible parts that caused the err or Troubleshooti.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 137 FIP-4 Panel Mess age Install K TnrCart Possible parts that caused the err or Troubleshooti.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 138 FIP-5 Panel Mess age Install P hotocondctr Possible parts that caused the err or Troublesh.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 139 FIP-6 Panel Mess age Photocon dctr T rouble Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 140 FIP-7 Panel Mess age Photocon dctr T rouble Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 141 FIP-8 Panel Mess age Photocon dctr T rouble Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 142 FIP-9 Panel Mess age Wrong P hotocon dctr Possible parts that caused the err or Troublesho.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 143 FIP-10 Panel Mess age Ton e rCar t Err or Y Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 144 FIP-11 Panel Mess age Ton e rCar t Err or Y Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 145 FIP-12 Panel Mess age Ton e rCar t Err or Y Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 146 FIP-13 Panel Mess age Wrong To ner Y Possible parts that caused the err or Troubleshooting.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 147 FIP-14 Panel Mess age Ton e rCar t Err or M Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 148 FIP-15 Panel Mess age Ton e rCar t Err or M Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 149 FIP-16 Panel Mess age Ton e rCar t Err or M Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 150 FIP-17 Panel Mess age Wrong To ner M Possible parts that caused the err or Troubleshooting.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 151 FIP-18 Panel Mess age Ton e rCar t Err or C Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 152 FIP-19 Panel Mess age Ton e rCar t Err or C Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 153 FIP-20 Panel Mess age Ton e rCar t Err or C Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 154 FIP-21 Panel Mess age Wrong To ner C Possible parts that caused the err or Troubleshooting.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 155 FIP-22 Panel Mess age Ton e rCar t Err or K Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 156 FIP-23 Panel Mess age Ton e rCar t Err or K Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 157 FIP-24 Panel Mess age Ton e rCar t Err or K Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 158 FIP-25 Panel Mess age Wrong To ner K Possible parts that caused the err or Troubleshooting.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 159 FIP-26 Panel Mess age Jam LC , G Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 160 11 Conti nuity chec k of HARNESS ASSY MAIN Disconne ct P/J4 21 from PWBA MCU. Do all of th e wiring below have normal continu ity? J421-7 ↔ J608 -4 J421-8 ↔ J608 -3 J421-9 ↔ J608 -2 Replace PWBA MCU.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 161 22 Operation c heck of CLUTCH AS SY FEED Does CLUTCH ASSY FEED operate normally? Make a te st print and co nfirm by t he operating noise. Go t o S t ep [ 30 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 162 FIP-27 Panel Mess age Jam MP, E Jam D, E Possible parts that caused the err or Troubleshooting ROLL MSI HOLDER ASSY RETARD MSI CHUTE ASSY PAPER GUIDE ROLL ASSY -PRE REGI ROLL-PINCH ACTUATOR-REGI.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 163 11 Continuity check of HARNESS-ASSY P/H1 Disconne ct the P/J4 08 from PWB A MCU. Do all of th e wiring below have normal continu ity? J408-10 ↔ J603-3 J408-11 ↔ J603-2 J408-12 ↔ J603-1 Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 164 21 Continuity check of HARNESS-ASSY P/H2 Disconne ct P/J6 03. Do all of th e wiring below have normal continu ity? P603 -1 ↔ P202- 2 P603 -2 ↔ P202- 1 Go t o S t ep [ 22 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 165 FIP-28 Panel Mess age Jam E Possible parts that caused the err or Troubleshooting ROLL.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 166 11 Operation chec k of SE NSO R REGI The vol t age of P408- 1 2 ↔ P408- 11 on PWBA MCU is 0 VDC when ACTUATOR REGI enter s the s ensor sens ing are a, an d is 5 VDC when it leaves t he sen sing area? Go t o S t ep [ 17 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 167 23 Continuity check of HARNESS-ASSY P/H2 Disconne ct P/J6 03. Do all of th e wiring below have normal continu ity? P603 -1 ↔ P202- 2 P603 -2 ↔ P202- 1 Go t o S t ep [ 24 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 168 FIP-29 Panel Mess age Jam E Jam D, E Possible parts that caused the err or Troubleshoo.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 169 10 Check after replac eme nt of MOTOR-PH Replace MOTOR-PH.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 170 FIP-30 Panel Mess age Jam E, F Jam D, E, F Possible parts that caused the err or Troub.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 171 11 Continuity check of HARNESS-ASSY P/H1 Disconne ct the P/J4 08 from PWB A MCU. Do all of th e wiring below have normal continu ity? J408-3 ↔ J603 -10 J408-4 ↔ J603 -9 Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 172 22 Continuity check of HARNES S ASSY 2BTR SENS Discon n ect P/J62 0 from HARNE SS ASSY 2BTR SE NS. Do all of th e wiring below have normal continu ity? P620 -1 ↔ J111-3 P620 -2 ↔ J111-2 P620 -3 ↔ J111-1 Replace SENSOR FUSER IN.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 173 32 Continuity check of HARNES S ASSY FUSER SENS and HARNESS ASSY FUSER in FUSER ASSY Allow FUSER ASSY to cool down before perfo rming work. Remove FUSE R ASSY .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 174 FIP-31 Panel Mess age Jam C, E, F Jam D, E, F Possible parts that caused the err or Tr.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 175 11 Continuity check of HARNESS-ASSY P/H1 Disconne ct the P/J4 08 from PWB A MCU. Do all of th e wiring below have normal continu ity? J408-3 ↔ J603 -10 J408-4 ↔ J603 -9 Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 176 22 Continuity check of HARNES S ASSY 2BTR SENS Discon n ect P/J62 0 from HARNE SS ASSY 2BTR SE NS. Do all of th e wiring below have normal continu ity? P620 -1 ↔ J111-3 P620 -2 ↔ J111-2 P620 -3 ↔ J111-1 Replace SENSOR FUSER IN.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 177 32 Continuity check of HARNES S ASSY FUSER SENS and HARNESS ASSY FUSER in FUSER ASSY Allow FUSER ASSY to cool down before perfo rming work. Remove FUSE R ASSY .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 178 FIP-32 Panel Mess age Check Transparency Possible parts that caused the err or Troubleshoo.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 179 FIP-33 Panel Mess age Jam E Jam D, E Possible parts that caused the err or Troubleshoo.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 180 11 Continuity check of HARNES S ASSY ADC Disconne ct P/J418 an d P /J620 from P WBA MCU. Do all of th e wiring below have normal continu ity? J418-1 ↔ J620 -3 J418-2 ↔ J620 -2 J418-3 ↔ J620 -1 Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 181 23 Conti nuity chec k of HARNESS ASSY MAIN Disconne ct P/J410 fr om PWBA MCU an d P/ J502 from LV/HVPS . Do all of th e wiring below have normal continu ity? J410-5 ↔ J502 -5 J410-6 ↔ J502 -6 J410-7 ↔ J502 -7 J410-8 ↔ J502 -8 Replace LV/ HVPS.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 182 FIP-34 Panel Mess age Jam C Jam D Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 183 10 Continuity check of HARNES S ASSY MCU C/L Allow FUSER ASSY to cool down before perfo rming work. Remove FUSE R ASSY . (p.388) Disconne ct P/J4 17 from PWBA MCU.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 184 FIP-35 Panel Mess age Jam D, E, DM Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 185 9 Check of ROLLER ASSY DUP, ROLLER ASSY DUP OUT and ROLL PINCH DUP Open Dupl ex. Are ROLLER ASSY DUP, ROLLER ASSY DUP OUT, and ROLL PINCH DUP attached correctly? Also, do the se parts rotate smooth ly without any dirt or damage? Turn by hand to ch eck.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 186 22 5 VDC power supply check to PWBA MCU The vol t age of P410- 3 ↔ P410- 4 on PWBA MCU is 5 VDC? Replace PWBA MCU. (p.404) Go to St e p [ 23 ]. 23 Conti nuity chec k of HARNESS ASSY MAIN Disconne ct P/J410 fr om PWBA MCU an d P/ J502 from LV/HVPS .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 187 FIP-36 Panel Mess age Jam DM Possible parts that caused the err or Troubleshooting SEN.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 188 10 Check after replac ement of MOTOR ASSY DUP (Lower Roll Motor) Replace MOTOR ASSY DUP. (p.443) Does the error recur when a test print is made in the duplex m ode? Go to Step [9].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 189 FIP-37 Panel Mess age Jam C Jam D Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 190 9 5 VDC power supply check to SENSOR UPPER PASS The vol t age of P444- 8 ↔ P444- 9 on PWBA DUP-L is 5 VDC? Go t o S t ep [ 10 ]. G o to St e p [ 15 ] . 10 Conti nuit y che ck of HARNESS-A SSY DUP1 Disconne ct P/J4 44 from P WBA DUP- L.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 191 FIP-38 Panel Mess age Jam DM Jam C Jam D Jam LC , G Jam E Jam D, E Jam C, .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 192 FIP-39 Panel Mess age Service Req E5 17 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 193 FIP-40 Panel Mess age Service Req E5 16 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 194 FIP-41 Panel Mess age Service Req E5 14 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 195 FIP-43 Panel Mess age Service Req E5 11 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 196 13 Conti nuity chec k of HARNESS ASSY MAIN Disconne ct P/J502 from L V/HVPS. Do all of th e wiring below have normal continu ity? J502-9 ↔ J201 -1 J502-10 ↔ J201-2 Replace LV/ HVPS.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 197 FIP-44 Panel Mess age Service Req E5 10 Possible parts that caused the err or Troubleshooting ROS A SSY HARNESS ASSY MAIN PWBA MCU LV/HVPS Step Check Yes No 1 Check of ROS ASSY a ttachment Re- a tta c h RO S ASSY.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 198 FIP-45 Panel Mess age Service Req E5 27 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 199 FIP-46 Panel Mess age Service Req E5 26 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 200 FIP-47 Panel Mess age Service Req E5 25 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 201 11 Check after replac ement of SENSOR HUM & TEMP Replace SENSOR HUM & TEMP. (p.400) Does the error recur wh en the power is turned ON? Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 202 FIP-48 Panel Mess age Service Req E5 24 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 203 11 Check after replac ement of SENSOR HUM & TEMP Replace SENSOR HUM & TEMP. (p.400) Does the error recur wh en the power is turned ON? Go t o S t ep [ 12 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 204 FIP-49 Panel Mess age Service Req E5 23 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 205 FIP-50 Panel Mess age Irregular Density Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 206 FIP-51 Panel Mess age Service Req E5 21 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 207 10 Power supply check to PWBA M CU Are each o f the p ower voltages being supplied to the fo llowing term inals on PWB A MCU from LV/HVPS? P410 -1 ↔ P410- 2: 3.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 208 FIP-52 Panel Mess age Service Req E5 20 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 209 11 Pow e r sup p ly ch ec k to PW B A M C U Are each o f the p ower voltages being supplied to the fo llowing term inals on PWB A MCU from LV/HVPS? P410 -1 ↔ P410- 2: 3.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 210 FIP-53 Panel Mess age Service Req E5 37 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 211 FIP-54 Panel Mess age Service Req E5 33 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 212 FIP-56 Panel Mess age Service Req E5 47 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 213 10 5 VDC power supply check to PWBA TRAY 500 The vol t age of P435- 6 ↔ P435- 5 on PWBA TRAY CONT is 5 VDC? Replace PWBA TRAY 500. (p. 456) Go t o S t ep [ 11 ].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 214 FIP-57 Panel Mess age Service Req E5 46 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 215 11 Conti nuity chec k of HARNESS ASSY MAIN Disconne ct P/J410 fr om PWBA MCU an d P/ J502 from LV/HVPS .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 216 FIP-58 Panel Mess age Service Req E5 42 Possible parts that caused the err or Troubleshoot.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 217 FIP-59 Panel Mess age Replace Toner Y Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 218 FIP-60 Panel Mess age Replace Toner M Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 219 FIP-61 Panel Mess age Replace Toner C Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 220 FIP-62 Panel Mess age Replace Toner K Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 221 FIP-63 Panel Mess age Replace Photocon dctr Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 222 FIP-64 Panel Mess age A Open Possible parts that caused the err or Troubleshooting COV.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 223 FIP-65 Panel Mess age E Ope n Possible parts that caused the err or Troubleshooting CH.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 224 FIP-66 Panel Mess age F Open Possible parts that caused the err or Troubleshooting CHU.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 225 FIP-67 Panel Mess age C Open Possible parts that caused the err or Troubleshooting COV.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 226 FIP-68 Panel Mess age G Open Possible parts that caused the err or Troubleshooting CHU.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 227 FIP-69 Panel Mess age DM Open Possible parts that caused the err or Troubleshooting CO.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 228 FIP-70 Panel Mess age D Open Possible parts that caused the err or Troubleshooting COV.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 229 FIP-71 Panel Mess age B Open Possible parts that caused the err or Troubleshooting COV.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 230 8 Operation chec k of SWITCH -INLK FU SER Disconnect P/J117 from SWITCH-INLK FUSE R. Is there contin uity o n P117-1 ↔ P117 -3 w hen SWITC H - I NLK FUSE R is pr e ssed, and do es the continu ity stop when t he switch is released? Go to Step [9].
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 231 FIP-72 Panel Mess age Y Toner Low Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 232 FIP-73 Panel Mess age M Toner Low Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 233 FIP-74 Panel Mess age C Toner Lo w Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 234 FIP-75 Panel Mess age K Toner Low Possible parts that caused the err or Troubleshooting .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 235 FIP-76 Panel Mess age Worn P hotocond uctor Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 236 FIP-77 Panel Mess age Worn P hotocond uctor Possible parts that caused the err or Troubles.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 237 FIP-78 Panel Mess age Service Req E9 98 Possible parts that caused the err or Troubleshooting FFC-AS SY E SS PWBA MC U BOARD ASSY.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 238 FIP-79 Ele ctrical Noise Possible parts that caused the err or Troubleshooting Photocond uctor.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 239 3.3.3.2 Controller related error FIP-C1 Panel Mess age Possible parts that caused the err or P.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 240 FIP-C2 Panel Mess age Possible parts that caused the err or Troubleshooting FIP-C3 Panel M.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING FIP accord ing to t he printe r messag e 241 FIP-C4 Panel Mess age Possible parts that caused the err or PWBA ESS Troubleshooting FIP-C.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 242 3.4 Printing Quality-related Trouble 3.4.1 Pri nting-quality tro ubleshootin g Entry Chart Figur e 3-4.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 243 NOTE: When hor izontal strip es and spots appear at fixed in terva ls, it is highl y possible that a specific ro ll has caused the trouble.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 244 3.4.2 Prin ting quality-related FIP FIP-P1 Printi ng is Faint (Weak Tones) Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 245 11 Check after re placement of th e MOT ASSY MAG Replace MOT ASSY MAG. (p.396) Make a te st print o f the probl em image. Is the ima ge printed n ormally? End of proced ure Go to S te p [ 1 2] .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 246 FIP-P2 Blank Pri nt Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 247 12 Check of imag e prim ary transfer pro cess Is the toner image on the drum trans f erred normally to IBT BELT?.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 248 FIP-P3 Sol id Black Prin t Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 249 FIP-P4 Vertical White Bands or Lines Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 250 FIP-P5 Horizont al White Bands o r Lines Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 251 10 Check of imag e secondary tra nsfer process Is the toner image on IBT BELT transferred normally to the pap er.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 252 FIP-P6 Vert ical Black Lines Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 253 FIP-P7 Ho rizontal Black Lines Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 254 FIP-P8 Image is Partia lly Not Pri nted Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 255 FIP-P9 Toner Smudges Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 256 FIP-P10 Resi dual Image Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 257 FIP-P11 Dark or Di rty Background Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 258 FIP-P12 Skew Print Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 259 FIP-P13 Pri nt Paper Damage Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 260 FIP-P14 Image Not Fixed Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 261 FIP-P15 Col or Shi ft Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 262 FIP-P16 Uneve n Dens ity/Thin- Spot Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 263 FIP-P17 Enti rely Faint Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 264 FIP-P18 Entirely Fogge d in Black Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 265 FIP-P19 Enti rely Thin Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Pri nting Quali ty-related Trouble 266 FIP-P20 Uneven Dens ity in Horizontal Directio n Before star ting troubleshooting, inspect the feed path of the printer pap er. Check the paper feed p ath for metal st aples, paper clips , paper scraps , and other f oreign matter.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 267 3.5 Abnormal Noise-r elated Trouble 3.5.1 Abnormal noise-rel ated troubles hooting entry chart Can you hear abnorm.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 268 3.5.2 Abnormal Noise-related FI P FIP-N1 At Powe r On Possible parts that caused the err or Troubleshootin.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 269 FIP-N2 At St andby Possible parts that caused the err or Troubleshooting MOT ASY FSR FUSE R ASSY .
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 270 FIP-N3 At Pri nting (One Side) Possible parts that caused the err or Troubleshooting 500 FEEDER ASSY O.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 271 17 Is abno rmal noise being ge nerated by M OT ASSY ROT? Re place MOT ASSY ROT. Go t o S t ep [ 18 ]. 18 Is abnormal no ise being gen erate d by FRAME ASSY-ROTARY that is driven by MOT ASSY ROT? Replace FRAME ASSY - ROTARY.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 272 FIP-N4 At Pri nting (Bot h Sides) Possible parts that caused the err or Troubleshooting 500 FEEDER ASS.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Abnormal Noise-rela ted Trou ble 273 16 Is abnormal no ise being generate d from HOUSING ASS Y-DEVE K, HO USING ASSY-DEVE Y, HOUSING ASSY-DEVE M, or HO.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Test Print 2 74 3.6 Test Print 3.6.1 Overvi ew To check th e IOT op era tion, it i s pos sible to pr in t PWBA MCU buil t-in sa mple continu ously witho ut bei ng routed t hrough the control ler.
EPSON AcuLaser C110 0 Revision B TROUBLESHOOTING Test Print 2 75 Figure 3-6. Test Print Pattern 400 dot line (400dpi) 1 dot line 127 dot 508 dot (400dpi).
CHAPTER 4 DISASSEMBLY AND ASSEMBLY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 277 4.1 Overview This secti on descri bes procedu res for disassembl ing the main component s of the product . Unless ot herwise speci fied, disas sembled units or components can be reassembled by reversing the d isassembly p rocedure.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 278 W ARNI NG Be careful not to let the developer or toner get into your eye or mouth, an d not to inha le it. And also ca re should be ta ken for people around you to prevent them from th e same thing.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 279 4.1.2 Before you s tart work This chapter describes the pr ocedu res for re movin g and attaching the main parts of the printer with the printer br oken down into 12 main com ponents accord ing to the parts list.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 280 4.1.3 List of Screws Many t ypes of screw s are us ed on this pr i nter . D o not m i stake n ly attach them at the wron g po sitions. Pay special attention when handling screws for plastic and screws for metal plates.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 281 4.1.4 Too ls Use only specified to ols to avo id damagi ng the p rinter. 6 For metal plat e Scr e w Silver Meta l plate • Silve.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY Overview 282 4.1.5 Conventions use d in descript ions of proc edures Express ions relating to directi ons in pr ocedures are d efined as f.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 283 4.2 COVER 4.2.1 COVE R ASSY TO P REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Rem ove th e 2 E-ri ng s fast ening CO VER A SSY TOP t o t h e mai n unit. 3. Open COVER ASSY TOP and si de it to th e right to remove it.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 284 4.2.2 TRAY EXTENSION , COVER TRAY REMOVAL 1. Draw out COVER TRA Y until it comes to a stop. 2. Open COVER ASSY TOP. 3. Un hook th e hook fasten ing C O VER TR AY to CO VER A SSY TOP , and re m ove COVER TRAY together with TRAY EXTENSION.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 285 4.2.3 COVER FUSER REMOVAL 1. Open COVER FUSER. 2. Draw out the COVER RH boss from the hole on COVER FUS ER while pushing COVER RH outward, a nd remov e COVER FUS ER. REINSTALLAT ION 1.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 286 4.2.4 COVE R TOP SIDE L REMOVAL 1. In the case of the DUPLEX s pecification, open DUPLEX ASSY. 2. In the case o f the standard s p ecification, open COVER FUSER. (p.285) 3. Open COVER ASSY TOP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 287 4.2.5 COVE R TOP SIDE R REMOVAL 1. In the case of the DUPLEX s pecification, open DUPLEX ASSY. 2. In the case o f the standard s p ecification, open COVER FUSER. (p.285) 3. Open COVER ASSY TOP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 288 4.2.6 SWIT CH ASSY TOP REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Unclamp the two clamps fastening th e ha rness of SWITCH A SSY TO P, and remove the harness. 3. Disc onnect conn ector (P/J11 6, blue) o f SWITCH A SSY TOP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 289 4.2.7 SWIT CH ASSY FRONT REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Unclamp the clamp f astenin g the h arne ss of SWITCH ASSY FRO NT and remove the harness. 3. Remove the screw (silver, with flange, 8 mm) fastening SWITCH ASS Y FRONT to the m ain unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 290 4.2.8 COVER RH, SLIDE BAR, COVER ROS WIND OW REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Unhook the four hooks fastening GUIDE BAR to COVER RH, an d remove GUIDE BAR. 3. Remove the screw (silver, with flange, tapping, 8 mm) fastening COVER ROS WINDOW to SLIDE BAR.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 291 4.2.9 COVE R MSI REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Slide COVER MSI in a slightl y open state to th e right to remove from the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 292 4.2.10 COV ER FRONT L , COVER FRO NT ASSY U REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Rem ove th e 3 sc rews (s ilv e r, wit h fla n ge, 8 mm) fa s teni ng COV ER FR ONT L to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 293 REINSTALLAT ION 1. Match the boss on COVER FRONT ASS Y U with the holes on COVER FR ONT L while bending down COVER FRONT ASSY U, an d attach COV ER FRONT ASSY U to COVER FRONT L.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 294 4.2.11 OP PANEL (CON TROL, PANEL ) REMOVAL 1. Open COVER ASSY TOP. 2. Open COVER FRONT ASSY U. 3. Remove the 3 screws (silver, with flange, 6 m m) fastening OP PANEL to th e main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 295 4.2.12 COV ER ASSY LH REMOVAL 1. In the case of the DUPLEX s pecification, remove DUPLEX ASSY. ( p.412) 2. In the case o f the standard s p ecification, remove COVER FUSER. (p.285) 3.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 296 REINSTALLAT ION 1. Match the squar e hole on the rear side of COVER ASSY LH with the interface connector on the rear side of the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 297 4.2.13 COV ER ESS REMOVAL 1. Loosen the screw fastening COVER ESS to the main unit. 2. Remove COVER ESS fro m the main unit. REINSTALLAT ION 1. Match the two p rotrusion s on t he botto m side of COVER ES S with t he holes on COVER LH, and attach COVER ESS.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 298 4.2.14 SWITCH ASSY FUSER, SW ITCH-FUSER DOOR REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Unclamp the clamp fastening the harnes s of SWITCH ASSY FUS ER and remove the harness. 3. Remove the screw (silver, with flange, 8 mm) fastening SWITCH ASS Y FUSER to the m ain unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 299 4.2.15 COV ER INN ER TOP REMOVAL 1. Rem ove OP PANE L. (p.294) 2. Rem ove th e 2 sc rews (s ilv e r, wit h fla n ge, 6 mm) fas teni ng COV ER IN NER TO P to the m ain unit. 3. Remove COVER INNER TOP from the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 300 4.2.16 SW ITCH-FRONT DOOR, SWIT CH-INLK FRONT REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove SWITCH ASSY FRONT. (p. 289) 3. Remove the screw (gold, 8 mm) fastening SWITCH-INLK FRONT to BRACKET INLK FRONT.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 301 4.2.17 COV ER ASSY RH REMOVAL 1. In the case of the DUPLEX s pecification, remove DUPLEX ASSY. ( p.412) 2. In the case o f the standard s p ecification, remove COVER FUSER. (p.285) 3.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 302 4.2.18 COV ER INN ER L REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY COVER 303 4.2.19 SW ITCH-INL K FUSE R REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Remo ve SWIT CH ASSY FUSE R. (p.298) 3. Remove the screw (silver, 8 mm) fastening SWITCH-INLK FUSE R to BRACKET INLK FUSER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 304 4.3 MSI 4.3.1 MSI ASSY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 305 REINSTALLAT ION 1. Gently insert HARNESS-ASS Y P/H 1 alon g the lef t side of MS I ASSY toget her with MSI ASSY from the front of the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 306 4.3.2 ROLL ASSY MSI REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 307 REINSTALLAT ION 1. Insert the left side of the shaft on ROLL ASSY MSI into the left-side bearing of MSI ASSY, and then slide ROLL ASSY M SI to the right and attach ROLL ASSY MSI.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 308 4.3.3 ROL L MSI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Unhoo k th e hook on t he righ t-side C ORE fasteni ng SH AF T ASS Y MS I, and s lid e to the rig ht.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 309 4.3.4 CHUTE MSI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Bend down CHU TE MSI, and d raw out the ri ght-si de boss o n CHUTE MSI from the right- side hole o n MSI ASSY to remo ve CHUTE MS I.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 310 4.3.5 GUI DE SIDE L, G UIDE A SSY SIDE R REMOVAL 1. Open COVER MSI. 2. Unhook the hoo ks fastening the ho les at the center of GUIDE SIDE COVER an d the hooks at the left and right of GUIDE SIDE COV ER from the holes on FRAME ASSY BOTTO M, and remove GUI DE SIDE COVER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 311 4.3.6 PLATE BOTTOM ASSY MSI REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 312 REINSTALLAT ION 1. Match the left side of PLATE BOTTOM ASSY MSI with th e attachment position on the lef t side of MS I ASSY, and insert the r ight side o f PLATE BOT TOM ASSY MSI from the notch on the right s ide of MSI ASS Y.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 313 4.3.7 HOLDER ASSY RETARD M SI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove C HUTE M SI.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 314 REINSTALLAT ION 1. Match SPRING RETARD MSI attached to HOLDER ASSY RETARD MSI with the sp ring bearing of FR AME ASSY BOTTO M, and attach the bosses o n both sides of HOLDER ASSY RETARD MSI to FRAME ASSY BOTTOM while bendin g down the bosses.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 315 4.3.8 PLATE ASSY RETARD REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove C HUTE M SI.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 316 REINSTALLAT ION 1. Match the lef t and right U gro oves of PLATE AS SY RETAR D with the boss es on the front of FRAME ASSY BOTTOM.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 317 4.3.9 OIL DA MPER REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 318 REINSTALLAT ION 1. Match the hole on OIL DAMPE R with t he boss on DAMPER BR ACKET, and attach OIL DAMPER to DAMPER BRACKET. 2. Match the hole on DAMPER BRACKET with th e boss on MSI ASSY, an d attach OIL DAMPER together with DAMPER BRAC KET.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 319 4.3.10 SO LENOID P ICK UP REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 320 REINSTALLAT ION 1. Match the hole on SOLENOID PICK UP with the boss o n MSI ASSY, and attach SOLENOID PICK UP. 2. Fasten SOLENOID PICK UP to MSI ASSY with the screw (silver, tapping, 8mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 321 4.3.11 SE NSOR PAPE R EMPTY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 322 4.3.12 ACT UATOR EMPT Y REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY MSI 323 REINSTALLAT ION 1. Slide the actuator of ACTUATOR EMPTY into the clearan ce of MSI ASSY, slide the shaft on ACTUATOR EMPTY along the notch on MSI ASSY, and attach ACTUATOR EMPTY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 324 4.4 PH ASSY 4.4.1 COVER-PH REMOVAL 1. Open COVER-PH. 2. Un hook th e hook s on bo th the l eft and righ t si des faste ni ng COV ER- PH to CHUTE ASS Y-REAR, an d remove COVER- PH. REINSTALLAT ION 1.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 325 4.4.2 CHUTE ASSY-REAR REMOVAL 1. In the case of the DUPLEX s pecification, remove DUPLEX ASSY. ( p.412) 2. In the case o f the standard specif ication, remove COVER-PH. ( p.324) 3. Open CHUTE ASSY-REAR.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 326 4.4.3 CHUTE-REAR UP, CHUTE-REAR LOW REMOVAL 1. Remove CHUTE AS SY-REAR. (p.325) 2. Remove the 2 screws (silver, with flange, tapping, 8 mm) fastening CHUTE- REAR LOW to CH UTE-R E AR UP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 327 4.4.4 FRAME ASSY-PH REMOVAL 1. In the case of the DUPLEX s pecification, remove DUPLEX ASSY. ( p.412) 2. In the case o f the standard specif ication, remove COVER-PH. ( p.324) 3. Open CHUTE ASSY-REAR.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 328 REINSTALLAT ION 1. Attach CHUTE ASSY-REAR. (p.325) 2. Turn FRAME ASSY-PH 90° in the d irection of the arrow, and conn ect connector (P/J603) and con nector (P/J604) connected to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 329 4.4.5 CLUTCH ASSY REGI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Rem o ve DRI VE ASSY- PH. (p.340) 4. Disconnect the con nector (P/J203) fro m CLUT CH ASSY R EGI, and r emove th e harness of CLUTCH ASSY REGI from the groove on FRAME ASSY-PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 330 4.4.6 ROL L-REGI ME TAL REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Rem o ve DRI VE ASSY- PH. (p.340) 4. Remo ve CLUTCH AS SY REGI. (p.329) 5. Remove the two E-rings f astening GEAR-REGI from FRAME ASSY- PH, and remove the two GEAR-REGIs.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 331 4.4.7 ROLL REGI RUBBER REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Rem o ve DRI VE ASSY- PH. (p.340) 4. Remo ve CLUTCH AS SY REGI. (p.329) 5. Remov e the E- ring fasten ing GEAR -REGI on ROLL REGI R UBBER fr om FRAME ASSY-PH, and remove GEAR-REGI.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 332 REINSTALLAT ION 1. Insert the shaft left side on ROLL REGI RUBBER into the left-side bearing on FRAME ASSY-PH, and slide ROLL REGI RU BBER to the right to attach. 2. Fas ten ROLL REGI RU BBER to FRAME AS SY-PH b y the le ft and r ight BEARING RUBBER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 333 4.4.8 ROLL ASSY-PRE REGI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Rem o ve DRI VE ASSY- PH. (p.340) 4. Remove CLUTCH ASSY PRE REGI. (p.338) 5. Remov e the E-rings fastening the right s ide of the s haft on ROLL ASSY-PRE REGI from FRAME ASSY-PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 334 4.4.9 SENSOR O HP REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Remove the screw (silver, with flange, tapping, 8 mm) fastening BRACKET- SENSOR OHP to FRAME ASSY -PH. 3. Remove BRACKET-SENSOR OHP together with SENS OR OHP from FRAME ASSY-PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 335 4.4.10 ACT UATOR-REGI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Remov e the left-s ide shaft on ACTUATOR-R EGI from th e hook on F RAME ASSY-PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 336 4.4.11 SE NSOR REG I REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Rem o ve DRI VE ASSY- PH. (p.340) 4. Unhoo k the three ho oks f astenin g SENSOR RE GI to FRAME A SSY-P H, down ACTUATOR-R EGI with yo ur finger s press and remove SENSOR REGI.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 337 4.4.12 MOT OR-PH REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Unhook the two hooks fastening COVER-HARNESS to FRAME ASSY-PH, and remove COV ER- HAR N ESS . 3. Unclamp the clamp on DRIVE ASSY-PH, and remove the harness of MOTOR- PH from the groov e on FRAME A SSY- PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 338 4.4.13 CL UTCH ASSY PRE REGI REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH .
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 339 4.4.14 SW ITCH-PH DOOR REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Disconnect connector (P/J100) from SWITCH-PH DOOR . 3. Open CHUTE ASSY-REAR. 4. Unhook the two hooks fastening SWITCH-PH DOOR to FRAME ASSY-PH, an d remove SWITCH-PH DOOR.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY PH ASSY 340 4.4.15 DRIV E ASSY-PH REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Rem ove MOT OR-PH . (p.337) 3. Unclamp the clamp on DRIVE ASSY-PH, and remove the harness. 4. Remove the 2 screws (silver, with flange, tapping, 8 mm) fastening DRIVE ASSY-PH to FRAME ASSY-PH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 341 4.5 TRANSFE R 4.5.1 CHUTE ASSY-FSR, COVER ASSY-RR 2N D REMOVAL CHUTE ASSY-FSR . 1. Open CHUTE ASSY-FSR. 2. Press t he hi ng e on CHUTE AS SY- FSR to th e inside with a flat-b lade screwdriver or a similar tool, and remove CHUTE ASSY-FSR from the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 342 COVE R ASSY -RR 2ND 1. Remove COVER ASSY LH. (p. 295) 2. Unclamp the clamp fastenin g the harnes s of COVER ASSY- RR 2N D, and remo ve the harness.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 343 REINSTALLAT ION COVE R ASSY -RR 2ND 1. Lead out the co nnector of the harn ess of COVER ASSY-RR 2ND from the hole on the main unit. 2. Match the boss on COVER ASSY-RR 2ND with the hole on the main unit, and attach COVER ASSY-RR 2ND.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 344 4.5.2 SENSOR FUSE R IN REMOVAL 1. Remove C HUTE ASSY-FSR. (p.341) 2. Remove the 2 screws (silver, with washer, tapping, 8 mm) fastening DIODE FUSER to CHUTE ASSY-FSR . 3. Remove DIODE FUSER from CHUTE ASSY-FSR.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 345 REINSTALLAT ION 1. Match the boss on SENSOR FUSER IN with the hole on CHUTE ASSY-FSR, and attach SENSOR FUSER IN. 2. Fasten SENSOR FUSER IN to CHUTE ASSY-FSR with the screw (silver, tappi ng, 6 mm ).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 346 4.5.3 FRAME ASSY-2ND REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 3. Remove 2ND BTR ASSY. (p.348) 4. Rem ove P LATE B IA S-2ND ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 347 REINSTALLAT ION 1. Attach BEARING-BRUSH C AM to the left-sid e bearing on the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 348 4.5.4 2ND B TR ASSY REMOVAL 1. Open COVER ASSY TOP. 2. Remov e Phot oconduct or Unit. 3. Turn th e levers o n both the left and right sides of 2ND B TR ASSY towards yo u, and unlock the lever lock f rom FRAME ASSY-2ND.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 349 REINSTALLAT ION 1. Insert the left-side gear on 2ND BTR ASSY into the main unit, and then fit the left and right bearings on 2ND BTR ASSY into FR AME ASSY -2ND to attach 2ND BTR ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 350 4.5.5 CAM ASSY-2ND REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 3. Remove 2ND BTR ASSY. (p.348) 4. Rem ove P LATE B IA S-2ND ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 351 REINSTALLAT ION 1. Attach BEARING to the left-side bearing on the main unit. 2. Attach BEARING to the right-side bearing on CAM AS SY-2N D.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 352 4.5.6 SWIT CH 2BTR COVE R REMOVAL 1. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 2. Disconnect the con nector (P/J113) fro m SWITCH 2BTR COVER. 3. Remove the screw (silv er, tapping, 6 mm) fastening BR ACKET-SWITCH 2ND to COVER- RR 2ND.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 353 4.5.7 SENSOR ASSY AD C REMOVAL 1. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 2. Remove the 2 screws (silver, with washer, tapping, 8 mm) fastening SENSOR ASSY ADC to th e main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 354 4.5.8 HO LDER -ADC 2ND REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 3. Remove 2ND BTR ASSY. (p.348) 4. Rem ove P LATE B IAS - 2ND.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 355 REINSTALLAT ION 1. Match the boss on SENSOR ASSY ADC with the hole on HOLDER-ADC 2ND, and attach SENSOR ASSY ADC. 2. Fasten SENSOR ASSY ADC to HOLDER-ADC 2ND with the 2 screws (silver, with washer, tapping, 8 mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 356 4.5.9 SENSOR 2BTR RETRACT REMOVAL 1. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 2. Disc onnect conn ector (P/J11 2) from SENSOR 2BTR RETRACT . 3. Remove the screw (silver, with flange, 8 mm) fastening BRAC KET-SEN SOR PHOTO to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 357 4.5.10 SE NSOR IBT R ETRACT REMOVAL 1. Rem ove OP PANE L. (p.294) 2. Remove COVER INNER TOP. (p.299) 3. Disc onnect connect or (P/J10 7) from SEN SOR IBT RETR ACT. 4. Remove the screw (silver, with flange, 6 mm) fastening BRAC KET-SEN SOR CLN to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 358 4.5.11 PLATE BIAS-2ND A SSY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 3. Remove 2ND BTR ASSY. (p.348) 4. Remove the 2 screws (silver, with flange, tapping, 6 mm) fastening PLATE BIAS- 2ND ASSY to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 359 REINSTALLAT ION 1. Attach WIRE ASSY 2BTR to PLATE BIAS-2ND ASSY. 2. Fasten the terminal of WIRE ASSY 2BTR to PLATE BIAS-2 ND ASSY with the screw (silver, tapping, 6 mm). 3. Match the boss on PLATE BIAS-2ND ASSY with the hole on the main unit, and attach PLATE BI AS-2ND ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY TRANSFER 360 4.5.12 CAM ASSY-IB T CL REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove OP PANE L. (p.294) 4. Remove COVER INNER TOP. (p.299) 5. Rem ove P WBA MC U .
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 361 4.6 XERO 4.6.1 SENSOR T R-0 REMOVAL 1. Open COVER ASSY TOP. 2. Remov e Phot oconduct or Unit. 3. Remove the screw (silver, with flan ge, 10mm) fast ening SEN SOR TR-0 to PLATE-TR-0. 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 362 4.6.2 GUIDE CRU A SSY D REMOVAL 1. Remove 2ND BTR ASSY. (p.348) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove P WBA MC U . (p.404) 4. R emove CHAS SIS AS SY ESS. (p.4 11) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 363 8. Unclamp the clamp fas tening HARNESS-A SSY XERO on the left side of the main un it. 9. Remove the 5 screws (silver, with flange, tapping, 6 mm) fastening GUIDE CRU ASSY D to t he m ain un it.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 364 4.6.3 LATC H ASSY D REMOVAL 1. Remove 2ND BTR ASSY. (p.348) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove P WBA MC U . (p.404) 4. R emove CHAS SIS AS SY ESS. (p.4 11) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 365 4.6.4 ANTE NNA ASSY REMOVAL 1. Remove 2ND BTR ASSY. (p.348) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove P WBA MC U . (p.404) 4. R emove CHAS SIS AS SY ESS. (p.4 11) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 366 REINSTALLAT ION 1. Connect connector (P/J109) to ANTENNA ASSY. 2. Match the boss on GUIDE CRU ASSY D with the hole on ANTENNA ASSY, attach ANTENNA ASSY, and fasten with a hook.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 367 4.6.5 GUIDE CRU A SSY AD REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove 2ND BTR ASSY. (p.348) 3. Remove FRAME ASSY-PH. (p.3 27) 4. Re move BC R CLN XE RO ASS Y. (p.373) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 368 8. Rem o ve WIRE ASSY BTR , WIRE ASS Y IBT a nd WIRE AS SY BCR fro m GUIDE CRU ASSY AD. 9. Remove the screw (silver, with flange, tapping, 6 mm) fastening WIRE ASS Y DTN to GUIDE CRU ASSY AD.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 369 REINSTALLAT ION 1. Match the protrus ion and boss on GUIDE CRU ASSY AD with the hole on the main unit, and attach GUIDE CRU ASSY AD. 2. Fasten GUIDE CRU ASSY AD to the main unit with th e 7 screws (si lver, with flange, tapping, 6 mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 370 4.6.6 LEVE R-LATCH PR REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove 2ND BTR ASSY. (p.348) 3. Remove FRAME ASSY-PH. (p.3 27) 4. Re move BC R CLN XE RO ASS Y. (p.373) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 371 4.6.7 CAP-PL ATE PR, PLA TE-ASSY PR REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove 2ND BTR ASSY. (p.348) 3. Remove FRAME ASSY-PH. (p.3 27) 4. Re move BC R CLN XE RO ASS Y. (p.373) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 372 4.6.8 LATCH ASSY AD REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove 2ND BTR ASSY. (p.348) 3. Remove FRAME ASSY-PH. (p.3 27) 4. Re move BC R CLN XE RO ASS Y. (p.373) 5. Rem ove S ENSO R TR-0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 373 4.6.9 BCR CLN XERO ASSY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove FRAME ASSY-PH. (p.3 27) 3. Dis connect conn ector (P/J 617) from BCR C LN XERO ASSY on th e right si de of the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY XERO 374 4.6.10 SE NSOR TNE R FULL REMOVAL 1. Remove FRAME ASSY-PH. (p.3 27) 2. Disc onnect connect or (P/J12 6) from SENSOR TNER F ULL. 3. Unhook the two hooks fastening SENSOR TNER FULL to the main unit, and remove SENSOR TNER FULL.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ROS 375 4.7 ROS 4.7.1 ROS ASSY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ROS 376 REINSTALLAT ION 1. Match the boss on ROS AS SY with the hole on the main unit, an d attach RO S ASSY. 2. Fasten ROS ASSY to the m a in un it with the 5 screws (silver, with flange, 10mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ROS 377 4.7.2 CLEANER ASSY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove the 2 screws (silver, with flange, 10mm) fastening GUIDE-ROS CLN to the main unit. 3. Remove GUIDE-ROS CLN from the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 378 4.8 DEVE 4.8.1 LATCH ASSY-ROTARY REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Rem o ve LV/H VPS. (p.407) 3. Remove the 3 screws (silver, with flange, tapping, 8 mm) fastening LATCH ASSY-ROTARY to the main un it.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 379 4.8.2 ANTE NNA ASSY-CTRG REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Rem ove A N TENN A CT RG . (p.380) 3. Remove the 2 screws (silver, with flange, tapping, 8 mm) fastening ANTENNA ASSY - CTRG to the main un it.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 380 4.8.3 ANTENN A CTRG REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Disc onnect conn ector (P/J10 6) from ANTENNA CTRG. 3. Unhook the hook fastening ANTENNA CTRG to ANTENNA ASSY-CTRG, and remove ANTENNA ASSY -CTRG.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 381 4.8.4 HO LDER ASSY-BIAS REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove WIRE ASSY DEVE connected to HOLDER AS SY-BIAS.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 382 4.8.5 SENSOR RO TARY HOME POSI REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Rem o ve LV/H VPS. (p.407) 3. Remove the screw (silver, with flange, 6 mm) fastening BRACKET SENSOR to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 383 4.8.6 HOUSING ASSY-DEVE K, HO USING ASSY- DEVE Y, HOUSING ASSY-DEVE M, HOUSING ASSY-DEVE C REMOVAL 1. Remove the To ner Cartridge. 2. Remove COVER ASSY RH. (p.301) 3. Remove COVER ASSY TOP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 384 10. Unhook t he hook on PIVOT A D fastening the righ t side of HOUSING ASSY- DEVE to FRAME ASSY-ROTARY, and remove PIVOT AD.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 385 2. Match the hole on HOUSING ASSY-DEVE with the attachment hole on the left side of FRAME ASSY-ROTAR Y, insert the shaft on PIVOT ASS Y, and fasten the left side of HOUSING ASSY-DEVE with the screw (silver, with flange, tappi ng, 8 mm ).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 386 4.8.7 FRAME ASSY-ROTARY REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY TOP. (p.283) 3. Remove 2ND BTR ASSY. (p.348) 4. Remove COVER ASSY LH. (p. 295) 5. Rem ove C OVER M S I.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DEVE 387 24. Remove the 2 screws ( silver, with flange, 6 mm) fastening SHAFT ASSY- ROTARY on the left side of the main unit. 25. Remove SHAFT ASSY-ROTAR Y from both sides of the main unit. 26.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY FUSER 388 4.9 FUSER 4.9.1 FUSER ASSY REMOVAL 1. In the case o f the DUPLE X specification, pr ess LI NK-BUTTON upwards, release the latch, and op en DUPLEX ASSY. 2. In the case o f the standard specif ication, open COVER FUSER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY FUSER 389 REINSTALLAT ION 1. Attach Spring to Actuator. 2. With Chute on FUSER AS SY open, insert the shaft of Actuator to the main unit, and attach together with Spring.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY FUSER 390 4.9.2 FU SER LOCK SW ITCH REMOVAL 1. Rem o ve FUSE R ASSY. (p.3 88) 2. Remove COVER ASSY LH. (p. 295) 3. Remove CHUTE ASSY-FSR and COVER ASSY-RR 2ND. (p.341) 4. Disc onnect the con nector (P/ J128, blue) from FUSER LOCK SWIT CH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY FUSER 391 REINSTALLAT ION 1. Match the prot rusion and hook o n FUSE R LOCK SW ITCH with the hol e on the main unit, slide FUSE R LOCK SWITCH to the left, and attach FUSER LOCK SWITCH.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY FUSER 392 4.9.3 HARN ESS ASSY MCU C/L REMOVAL 1. Rem o ve FUSE R ASSY. (p.3 88) 2. Remove COVER ASSY LH. (p. 295) 3. R emove CHAS SIS AS SY ESS. (p.4 11) 4. Disconnect the con nector (black-and -white) from PWBA FUSER CONT.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 393 4.10 DRIVE 4.10.1 DRIV E ASSY BT R REMOVAL 1. Remove 2ND BTR ASSY. (p.348) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove P WBA MC U . (p.404) 4. R emove CHAS SIS AS SY ESS. (p.4 11) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 394 4.10.2 DRIV E ASSY PRO REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Rem ove OP PANE L. (p.294) 3. Remove COVER INNER TOP. (p.299) 4. Disc onnect conn ector (P/J41 1,P/J4 14) from t he PWBA MCU.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 395 4.10.3 MOT ASSY FSR REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disconn ect connect or (P/J40 4) from th e PWBA MCU. 3. Unclamp the clamp fas tening the harn ess on MOT ASSY FSR and remo ve the harn ess.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 396 4.10.4 MOT ASSY MAG REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. R emove CHAS SIS AS SY ESS. (p.4 11) 3. Disconn ect connect or (P/J40 5) and connecto r (P/J406) from PWB A MCU. 4. Remove the 3 screws (s ilver, with flange, 10 mm) fastenin g MOT ASSY MAG to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 397 4.10.5 MOT ASSY ROT REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 398 4.10.6 MOT ASSY P/R REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disc onnect connect or (P/J20 0) and connect or (P/J201) from MOT A SSY P/R . 3. Rem ove th e 4 sc rews (s ilve r, wit h flan ge, 1 0 mm) fa steni n g MO T A SSY P/R to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DRIVE 399 4.10.7 MOT ASSY MICRO REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Unclamp the clamp fas tening the h arness on MOT ASSY MICRO. 3. Disconn ect connect or (P/J60 0) from MOT A SSY MICRO.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 400 4.11 ELEC 4.11.1 SE NSOR HUM & TEMP REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Disc onnect connect or (P/J10 4) from SEN SOR HUM & TEMP. 3. Remove the screw (silver, with flange, tapping, 8 mm) fastening SENSOR HUM & TE MP to th e m ain uni t.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 401 4.11.2 PWBA HVPS REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 402 4.11.3 PWB ASSY ROT REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 403 4.11.4 PWBA CRUM REMOVAL 1. Remove COVER ASSY RH. (p.301) 2. Remove COVER ASSY LH. (p. 295) 3. Rem ove C OVER M S I. (p.291) 4. Remove COVER FRONT L and COVER FRONT ASS Y U. (p.292) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 404 4.11.5 PWBA MCU When usi ng the old PWBA MCU REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disconnect all connectors from the PWBA MCU. 3. Rem ove t h e 4 s c rew s (s ilv er, wi t h fl ange, 6mm) fastening PWBA MCU to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 405 When replacing PWBA MCU with a new o ne The life information of the re pl acement parts, correction p arameters, etc are stor ed in EEPROM on th e MCU board (PWB A MCU).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 406 Table 4-8. Symptoms when the connector is loo se Connector No. Panel Indication Symptom Error Caused by Co nnecto r Disconnection P/J400 --- P rinting is not possible. --- P/J401 Service Req E537 Printing is n ot possible.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 407 4.11.6 LV /HVPS REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disconnect all conn ectors from the LV/HVPS. 3. Remove the 6 screws (silver, with flange, 6 mm) fastening LV/HVPS to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 408 Table 4-9. Symptoms when the connector is loo se Connector No. Panel Indication Symptom Error Caused by Co nnecto r Disconnection P/J501 --- Co nt rol pa n el is not av ailable. --- P/J502 --- P rinting is not possible.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 409 4.11.7 PWB A ESS (BOA RD ASSY., MAIN) REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disconnect all conn ectors from the PWBA ESS. 3. Rem ove th e 4 sc rews (s ilv e r, wit h fla n ge, 6 mm) fa s teni ng PW BA ESS t o CHASSIS ESS and the screws fasten ing the interface conn ectors.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 410 4.11.8 PWBA FUSER CONT REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. R emove CHAS SIS AS SY ESS. (p.4 11) 3. Disconnect all conn ectors from the PWBA FUSER CONT. 4. Rem ove th e 2 sc rews (s ilve r, wit h flan ge, 8 mm) fas ten i ng PWBA F USER CONT to the m ain unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY ELEC 411 4.11.9 CHA SSIS ASSY E SS (REF ERENC E ONLY) REMOVAL 1. Remove COVER ASSY LH. (p. 295) 2. Disconnect all conn ectors from the PWBA ESS. 3. Remov e disc onnected connect ors f rom the ho le on CHA SSIS E SS.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 412 4.12 DUPLEX 4.12.1 DUPL EX ASSY REMOVAL 1. Press LINK-BUTTON upward to release the latch and open DUPLEX ASSY. 2. Remove COVER CONNECTOR, and disconnect connector (P/J607) connected to the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 413 4.12.2 COV ER-R DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the 3 screws (silver, with flange, tapping, 10mm) fastening COVER-R DUP to DUPLEX ASSY. 3. Remove COVER-R DUP from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 414 4.12.3 COV ER-L D UP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the 3 screws (silver, with flange, tapping, 10mm) fastening COVER-L DUP to DUPLEX ASSY. 3. Remove COVER-L DUP from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 415 4.12.4 COV ER-INV REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK LATC H and LINK-BUTTON. (p.4 16) 5. Open COVER UP-DUP TRAN S, and remove INVERTER ASSY DUP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 416 4.12.5 LI NK-LATCH, L INK-BUTTO N REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Un hook th e hook faste n ing L I NK-BU T TON to DUP LEX AS SY, and remo v e LINK-BUTTON together with LINK-LATCH and SPRING-LINK.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 417 4.12.6 INVE RTER ASSY DU P, TRANSPOR T ASSY DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 418 REINSTALLAT ION 1. Match each of the b osses and holes on INVER TER ASSY DUP with TRANSPORT ASSY DUP , and attach INVERTER ASSY DUP to TRANSPORT ASSY D UP. 2. Attach INVERTER ASSY DUP to TRANSPORT ASSY DUP with the 2 screws (silver, with flange, tapping, 10mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 419 4.12.7 SO LENOID ASSY DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON. (p.416) 5. Open COVER UP-DUP TRAN S, and remove INVERTER ASSY DUP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 420 3. Connect connector (P/J611) to SOLENOID ASSY D UP. 4. Attach COVER-INV. (p.415) 5. Attach INVERTER ASSY DUP . (p.417) 6. Attach LINK-LATCH and LINK-BUTTON. (p.41 6) 7. Attach COVER-L DUP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 421 4.12.8 ACT UATOR INV REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON. (p.416) 5. Open COVER UP-DUP TRAN S, and remove INVERTER ASSY DUP.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 422 4.12.9 SE NSOR UPPE R PASS REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON. (p.416) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 423 REINSTALLAT ION 1. Match the hook on SENSOR UP PER PASS wit h the att achment posi tion, and attach to BRACKET-SNS.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 424 4.12.10 MO TOR ASSY DUP INV REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-L DUP. (p.414) 3. Remove the 4 screws (silver, with flange, tapping, 10mm) fastening BRACKET- MOTO INV to DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 425 3. Connect connector (P/J612) of MOTOR ASSY DUP INV to BRAC KET-MO TO INV. 4. Match the hole on BRACKET-MOTO INV with the shaft on DUPLEX ASSY, and attach together with MOTOR ASSY DUP INV.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 426 4.12.11 RO LLER ASSY INVE RTER REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON. (p.416) 5.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 427 4.12.12 CH UTE ASSY-INV LOW REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the 2 screws (silver, with flange, tapping, 10mm) CHUTE ASSY-INV LOW to DUPLEX ASSY. 3. Remove CHUTE ASSY-INV LOW from DUPLEX ASSY .
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 428 4.12.13 L ATCH DUP R , LATCH DUP L REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove LINK-LATC H and LINK-BUTT ON. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 429 REINSTALLAT ION 1. Match the protrus ions on LATCH DU P R and LA TCH DUP L wi th th e notches o f hole on DUPLEX ASSY, attach to SHAFT LATCH, turn LATCH DUP R and LATCH DUP L, and faste n LATCH DUP R and LATCH DUP L to DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 430 4.12.14 SWI TCH-DUP DOO R REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remov e the sc rew (s ilv er, with flang e, tapp ing, 10 mm ) fast ening C OVER R EAR from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 431 4.12.15 ACT UATOR DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the screw (silver, with flange, tapping, 10mm) fastening COVER R EAR from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 432 4.12.16 SEN SOR LO W PASS REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the screw (silver, with flange, tapping, 10mm) fastening COVER R EAR from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 433 4.12.17 SUPPO RT DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the KL ring fastening SUPPORT DUP to the sh aft on DUPLEX AS SY. 3. Remove S UPPORT DUP from the shaft on DU PLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 434 4.12.18 H INGE ASSY L REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-L DUP. (p.414) 3. Remove the E- ring fasten ing HINGE ASSY L to DUPLEX AS SY. 4. Remove HINGE ASSY L from DUPLEX ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 435 4.12.19 H INGE ASSY R REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove the E- ring fasten ing HINGE ASSY R to DUPLEX ASSY. 4. Remove HINGE ASSY R from DUPLEX ASSY together with HINGE-R.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 436 4.12.20 CO VER LOW-DUP TRANS REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove the 2 screws (silver, with flange, tapping, 10mm) fastenin g COVER LOW-DUP TRANS to DUPLEX ASSY. 3. Remove COVER LOW-DUP TRANS from DUPLEX ASS Y.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 437 4.12.21 CO VER UP-DUP TRAN S REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER LOW-DUP TRANS.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 438 4.12.22 PAD DAMPER L REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-L DUP. (p.414) 3. Remove HINGE ASSY L. (p.434) 4. Remove the screw (silver, with flange, 6 mm) fastening BRACKET PAD L to HINGE-L.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 439 4.12.23 PAD DAMPER R REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove HINGE ASSY R. (p.435) 4. Remove the screw (silver, with flange, 6 mm) fastening BRACKET PAD R LOWER to BRACKET AS SY R.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 440 4.12.24 RO LLER ASSY DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove COVER LOW-DUP TRANS. (p .436 ) 5. Remove COVER UP-DUP TRAN S.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 441 REINSTALLAT ION 1. Insert the shaft left side on ROLLER AS SY DUP into the left-side bearin g on DUPLEX ASSY, and slide RO LLER ASSY DUP to the right to attach.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 442 4.12.25 PW BA DUP-L REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-L DUP. (p.414) 3. Disc onnect connect or (P/J44 2), connecto r (P/J443 ) and connector (P/J444) from PWBA DUP-L.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 443 4.12.26 MO TOR ASSY DUP REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-L DUP. (p.414) 3. Unclamp the clamp on BKT MOTOR DUP TRANS, and remo ve the harness. 4. Dis connect conn ector (P/J 444) from PWBA DU P-L.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 444 REINSTALLAT ION 1. Match th e harness si de of MOTOR ASSY DUP with the mark on BKT MOTOR DUP TRANS, and attach to MOTOR ASSY DUP . 2. Fasten MOT OR ASSY DUP to BKT MOT OR DUP TRANS with the 4 screws (silver, 5mm).
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY DUPLEX 445 4.12.27 RO LLER ASSY DUP O UT REMOVAL 1. Rem o ve DUP LEX ASSY . (p.412) 2. Remove COVER-R DUP. (p.413) 3. Remove COVER-L DUP. (p.414) 4. Remove COVER LOW-DUP TRANS. (p .436 ) 5. Remove COVER UP-DUP TRAN S.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 446 4.13 500 PAPER CASSETTE & 500 PAPER FEEDER 4.13.1 500 PAPER CASSETTE ASSY REMOVAL 1. Draw out 500 PAPER CASSETTE ASSY until it comes to a stop, then slightly lift up the fron t side, and remove 500 P APER CASSETTE ASSY from 5 00 PAPER FEEDER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 447 4.13.2 GUI DE END ASSY REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 448 4.13.3 PL ATE ASSY BOTT OM 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Slide LOCK LIFT R and L OCK LIFT L, and unlock the locks . 3.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 449 REINSTALLAT ION 1. Match the boss on the rear of PLATE ASSY BOTTOM 500 with SPRING NF.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 450 4.13.4 GUI DE PAPER L ASSY 500, GUID E PAPER R ASSY 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Rem ove P LATE AS SY BO TTOM 500. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 451 4.13.5 COV ER FRONT CST 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove the 2 screws (silver, with flange, tapping, 8 mm) fastening COVER FRONT CST 500 to 500 PAPER CASS ETTE ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 452 4.13.6 500 PAPER FEEDER ASSY (REFERE NCE ONLY) REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Turn L OCK MC TO FDR on bot h the left and rig ht sides CW by 90° to unlock from the main unit.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 453 4.13.7 COV ER LEF T 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Rem ove t h e 5 sc rew s (s ilv e r, wit h fla nge, 8 mm) fa ste ni ng CO VER L EFT 50 0 to 500 PAPER FE EDER ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 454 4.13.8 CHU TE FDR ASSY 5 00 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove COVER RIGHT 500. (p.455) 3. Remove the screw (silver, with flange, tapping, 8 mm) fastening CHUTE FDR ASSY 500 .
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 455 4.13.9 COV ER RIGH T 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove the 5 screws (silver, with flange, 8 m m) fastening COVER RIGHT 500 to 500 PAPER FE EDER ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 456 4.13.10 PW BA TRAY 500 REMOVAL 1. Remov e COVER LEFT 50 0. (p.4 53) 2. Disc onnect connect or (P/J43 5), connecto r (P/J436 ) and connector (P/J437) from PWBA TRAY 500.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 457 4.13.11 PW BA MOT REMOVAL 1. Remov e COVER LEFT 50 0.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 458 4.13.12 DRI VE ASSY FEED REMOVAL 1. Remov e COVER LEFT 50 0. (p.4 53) 2. Remove CLUTC H ASSY FEED. (p.461) 3. Disc onnect conn ector (P/J44 6) from PWBA MOT an d connector (P/J610) from SOLENOID FEED.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 459 4.13.13 SOL ENOID FEED REMOVAL 1. Remov e COVER LEFT 50 0. (p.4 53) 2. Remove CLUTC H ASSY FEED. (p.461) 3. Rem o ve DRI VE ASSY F EED. (p.458 ) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 460 4.13.14 MO TOR ASSY FEEDER REMOVAL 1. Remov e COVER LEFT 50 0. (p.4 53) 2. Unclamp the clamp on DRIVE ASSY F EED, and remove t he harn ess on MOT OR ASSY FEEDER.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 461 4.13.15 CL UTCH ASSY FEED REMOVAL 1. Remov e COVER LEFT 50 0. (p.4 53) 2. Unclamp the clamp on DRIVE ASSY FEED, and remove th e harness on CLUTCH ASSY FEED.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 462 4.13.16 H ARNESS-ASSY FEED 1 REMOVAL 1. Remove 5 00 PAPER FEE DE R ASSY. (p.452) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Unclamp the clamp fas tening the h arness of HARNES S-ASSY FEED 1.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 463 4.13.17 RO LL ASSY TURN 500 REMOVAL 1. Remove C HUTE FDR ASSY 500. (p.4 54) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 464 4.13.18 SWI TCH FE EDER DO OR REMOVAL 1. Remove C HUTE FDR ASSY 500. (p.4 54) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remov e the screw (si lver, tapp ing, 8 mm) fasten ing CAP FE EDER to 500 PAP ER FEEDER ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 465 4.13.19 H ARNESS-ASSY FEED 2 REMOVAL 1. Remove 5 00 PAPER FEE DE R ASSY. (p.452) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Unclamp the clamp fas tening the h arness of HARNES S-ASSY FEED 2.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 466 4.13.20 CH UTE ASSY 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 467 REINSTALLAT ION 1. Insert the left-side shaft o n CHUTE ASSY 500 into the bearing o n GUIDE CST L. 2. Inser t the right -side shaft o n CHUTE ASSY 500 in to the bearing on GUIDE CST R, and attach CHU T E AS SY 5 00 to 500 PAPER FEE DER ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 468 4.13.21 H OLDER A SSY RETARD 50 0 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 469 REINSTALLAT ION 1. Match SPRING RETARD with the boss o n CHUTE ASS Y 500, and at tach HOLDER ASSY RE TARD 500 to CHUTE AS SY 500 while ben ding dow n the bosses on both s ides of HOLDER A SSY RETARD 500.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 470 4.13.22 FIL M ASSY FDR REMOVAL 1. Open CHUTE FDR ASSY 500. 2. Rem ove th e 4 sc rews (s ilv e r, tap ping , 8 mm) faste ni ng FI LM AS SY FDR t o CHUTE ASSY 500.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 471 4.13.23 STO PPER CST R REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 472 4.13.24 G UIDE CST R REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 473 4.13.25 G UIDE CST L REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 474 REINSTALLAT ION 1. Attach STOPPER CST L. (p.475) 2. Match the boss on GUIDE C ST L with t he hole on 500 PAPE R FEEDER ASSY while inserting SWITCH FEEDER DOOR into the hole on the rear of GUIDE CST L, and attach GUIDE C ST L.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 475 4.13.26 STO PPER CST L REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remove C HUTE FDR ASSY 500. (p.4 54) 3. Remove COVER RIGHT 500. (p.455) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 476 4.13.27 H OUSING ASSY FEE D REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 477 REINSTALLAT ION 1. Match the 4 hooks on HOUSING ASSY FEED with the attachment positions, and attach to 500 PAPER FEE DE R ASSY.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 478 4.13.28 SEN SOR NO PAPER REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED. (p.461) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 479 4.13.29 ACT UATOR NO P APER CST REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 480 REINSTALLAT ION 1. Insert the shaft on ACTUATOR NO PAPER C ST from the notch on HOUSING ASSY FE E D .
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 481 4.13.30 ACT UATOR T/R REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED. (p.461) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 482 4.13.31 SEN SOR T/ R REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED. (p.461) 4.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 483 4.13.32 RO LL ASSY FEED 500 REMOVAL 1. Remov e 500 PAPER CASSETTE ASSY. (p.446) 2. Remov e COVER LEFT 50 0. (p.4 53) 3. Remove CLUTC H ASSY FEED. (p.
EPSON AcuLaser C110 0 Revision B DISASSEMBLY AND ASSEMBLY 500 PAPER CASSETTE & 500 PAPER FEEDER 484 REINSTALLAT ION 1. Attach ROLL ASSY FEED 5 00 to SHAFT FEED s o that the hook on ROLL ASSY FEED 500 is facing the righ t side, and fas ten the hook on ROLL ASSY FEED 500 to the groo ve on SHAFT FEED .
CHAPTER 5 ADJUSTMENT.
EPSON AcuLaser C110 0 Rev is io n B ADJUSTMENT Overvie w 486 5.1 Overview This chapter explains the adjustment necessary to maintain the functions an d perform ance of the AcuLaser C1 100. 5.1.1 Ins tructions Before starting yo ur adjus tment wor k, always check the CAUTION on the r ight.
EPSON AcuLaser C110 0 Rev is io n B ADJUSTMENT Overvie w 487 5.1.3 Wr iting USB ID AcuLaser C1100 is equipp ed with a USB interface as a s tandard feature. The PC connected to the printer via the USB interface id entifies the printer by referring to the USB ID information specific to each prin ter.
EPSON AcuLaser C110 0 Rev is io n B ADJUSTMENT Overvie w 488 5.1.3.2 Writing Method The method of writing USB ID differs according to the condition of the main board. Referr ing to the following table, figure out what to d o dependi ng on th e conditions .
EPSON AcuLaser C110 0 Rev is io n B ADJUSTMENT Overvie w 489 5.1.4 Controll er Firmware Update This secti on explains a Contr oller firm ware update. NOTE: The computer shoul d be able to send binar y data under DOS via a parallel i nterface. 1. Prin t a status sheet, and check the current firmware version.
EPSON AcuLaser C110 0 Rev is io n B ADJUSTMENT Overvie w 490 5.1.5 MCU Fi rmware Update This secti on explains an MCU fi rm ware (engine fi rmware) update. NOTE: The computer shoul d be able to send binar y data under DOS via a parallel i nterface. 1.
CHAPTER 6 MAINTENANCE.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Overview 492 6.1 Overview This section gives information necessar y for maintaining the prin ter in its optimum condition. In maintenance an d checks, never fail to observe the fo llowing precautions. W ARNI NG To prevent an electric shock, bu rn, injury, etc.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Overview 493 C A U T I O N Since th is printer has many meta l parts , bewa re of the f rame edges and similar portions and be sure to we ar gloves to wo rk. Do not disassemble the Toner Cartridge and the Photocond uctor Unit.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE About On-sit e Servici ng 494 6.2 About On-site Servicing This secti on explai ns th e maintenan ce work to be done when you actually v isit the us er site. To prev ent possible accidents durin g maintenance work, strictly o bserve the servicin g warnin gs and cauti ons.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE About On-sit e Servici ng 495 6.2.2 Details of O n-site Servicing This secti on explains the detai ls of on-s ite servicin g.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE About On-sit e Servici ng 496 Preventive Maintenance (Co nsuma ble s/C ompo nent s n eeding periodic replacement) Do preventive maintenance work to mainta in the printer perfor mance and p revent failures fro m occurring .
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Maintenance Menu 4 97 6.3 Maintenance Me nu This menu i s displa yed and select able onl y when a special oper ation perfor med at power-on to enter the maintenance mode. Basically, this menu is provided to be used by a service personnel for mainten ance.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Maintenance Menu 4 98 6.3.2 Entry into Maintenance Mode 1. Wh ile ho ldi ng down the [Back ], [U p], [Dow n] an d [Ent er] b utto ns, t urn th e prin ter on. When the printer is turned o n, all LEDs and LCD light and the following message is then displayed.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 499 6.4 Shee t for Servicing 6.4.1 Engi ne Status Sheet 6.4.1.1 Engine Status Sheet Items Total Counts Total Pag es : Total number of pages print ed to date. Color Pages : Total number of pages p rinted in color to date.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 500 2nd BTR Offset Normal : Settin g value of the transfer voltage for plain paper. SemiThk : Settin g value of the transfer voltage for High q uality paper. Thick : Setting value of t he transfer voltage for thick paper.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 501 Paper size: Indicated same as the panel display. Paper t ype: Indicated as the specified value set for each media to control the engine. Note *1 : The date and ti me are ind icated in th e local tim e when generate d.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 502 6.4.1.2 List of information managed and methods of management Table 6-3. Li st of info rma tion managed a nd methods of ma nage.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 503 2nd BT R 2nd BTR Change En gine Controller 0 to 0 to 255 pages Times Duri ng p rinti ng Cou nt er cl ear Cou nt er c lea r (EEP.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 504 6.4.2 Pri nt Log Report 6.4.2.1 Print Log Report Items S/N : Serial number of mai n unit Date : yyyy/mm/ dd hh:mm (Local time) Not displayed when it is in asynchronous state.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Sheet fo r Servicing 505 6.4.2.2 List of information managed and methods of management Note *1 Va lues in parentheses in the Clear Condition c olumn ar e cleared as a result. *2 If a va lue exceeds its ran ge, it is not guar anteed if it is cont ro lled by the con t roller.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Co nsumables and Co mponents needi ng Periodi c Replacement 506 6.5 Consumables and Components needing Periodic Replac ement 6.5.1 Consumables C A U T I O N The print page-based service life values of the Consumables and Periodical Replacement Parts a re guidelines.
EPSON AcuLaser C110 0 Rev is io n B MAINTENANCE Co nsumables and Co mponents needi ng Periodi c Replacement 507 6.5.2 Regular Replac ement Parts *1:The s ame functi on is also available i n the rese t menu.
EPSON AcuLaser C110 0 Rev is io n B MAINT ENANCE G lueing /Lubric ation 508 6.6 Glueing/Lubrication This secti on explains the part req uired gluein g and lub rication when per forming the service wor k, or repl acing the un it or part s. 6.6.1 Glueing There is no relevant glueing part for this unit.
EPSON AcuLaser C110 0 Rev is io n B MAINT ENANCE G lueing /Lubric ation 509 6.6.2 Lubri cation The part requires lubrication for this unit is as below Parts Nam e CHUTE ASSY FSR Lubr icati on Part S p.
CHAPTER 7 APPENDIX.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 511 7.1 Connector s This section shows the con nector locations of EPSON AcuLaser C1100. [P] an d [J] represent “p lug” and “jack”, respectively. 7.1.1 The L ist of Plugs and Jacks IOT Table 7-1 .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 512 DUP 430 E-1 09 Conne cts PWB ASSY ROT and HARNESS ASS Y MAIN 431 F-1 38 Connects SENS OR ASSY ADC and HARNESS ASSY ADC 432 D-109 Conne cts .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 513 500 F EEDER 7.1.2 P/J Layout Diagram Figure 7-1. I OT P/J L ayout Diagra m (1) Table 7- 3.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 514 Figure 7- 2. IOT P/J L ayout D iagram (2) Figure 7-3. I OT P/J L ayout Diagra m (3) 604 603 605 103 100 202 101 102 203 A 11 7 11 8 11 9 12.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 515 Figure 7- 4. IOT P/J L ayout D iagram (4) Figure 7-5. DUP P/J L ayout D iagram 501 515 504 503 508 509 502 500 608 3 2 1 CN501 CN405 CN601 .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Connector s 516 Figure 7-6. 500 FE EDER P/ J Layout Diagram 121 608 618 120 1 19 446 609 610 4358 436 435 437 440 A 302 303 304 305 306 307 308 309 310 31 .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connect ion Diag rams 517 7.2 Wiring Connection D iagrams 7.2.1 Marks used in the Overall Wiring Connection Diagram The table below shows how to interpret the Overall Wiring Connection Diagrams. Table 7-4.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connect ion Diag rams 518 7.2.2 Overall W iring Connection Diagrams Figure 7-7. Overa ll Wi ring Connect ion Diagrams PWBA FUSER CONT PL12.2.12 P/J1 P/J2 P/J3 P/J4 PWBA MCU PL12.2.1 P/J401 PWBA ESS PL12.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 519 7.3 Wiri ng Conn ection Diagram between Parts 7.3.1 Marks used in the D iagram and Ins tructions for Use The table below shows how to interpret the Wiring Co nnection Diagram between Parts.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 520 7.3.2 Composi tion of the Wiring Connection Diagram between Parts The Overall Wiring Connection Diagram is divided into 11 sections as shown below to indicate the detailed conn ection between parts.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 521 7. DEVELOPER (p 528) Connection between PWBA MCU and SWITCH FRONT-DOOR Connection between PWBA MCU and.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 522 1. DC POWER SUPPLY Overcurrent Protection All outputs (+24VDC, +5VDC, +3.3VDC) from LV/HVPS are stopped when short-circuiting on the way to the earth or ground.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 523 2. MSI& REGI Figure 7-9. M SI®I Connection and Wiring Diagram Name of sign al line Remar ks PAPER EMPTY SENSED (H) +5VDC Paper detection signal fo r MSI generated by Sens or Ph oto (No Pap er Se nsor) P/H MOTER ON (H)+3.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 524 3. FEED ER (500 ) Figure 7-10. FEEDER (500 ) Connection and Wiring Diagram Name of sign al line Remar ks TRAY SENSOR RXD TXD PWBA TRAY CONT.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 525 4. RO S Figure 7-11. ROS Co nnect ion and Wiring Diag ram Name of sign al line Remar ks ESS DAT A- ESS DAT A+ .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 526 5. XEROGRAPHIC Figure 7-12. XEROGRAPHIC Connection and Wiring Diagram Name of sign al line Remar ks IBT BRUSH .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 527 6. HIGH VOL TAGE Figure 7-13. HIGH VOLTAGE Connection and Wiring Diagram Name of sign al line Remar ks 1st BTR.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 528 7. DEVELOPER Figure 7-14. DEVELOPE R Connectio n and W iring Di agram Name of sign al line Remar ks MAG ROLL MOT ON MAG ROLL MOT PWM MAG ROLL MOT TG MAG ROLL MOT CW/CCW Magnet Roll Motor drive contro l signal TEM P.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 529 8. 2ND BTR Figure 7-15. 2nd BTR Connecti o n an d Wiri n g Diagr am Name of sign al line Remar ks FUSER IN SEN.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 530 9. FUSE R Figure 7-16. FUSE R Connection an d Wiri ng Diagram Name of sign al line Remar ks FUSER MOT ON (H)+ 3.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 531 10. CONTROLLER Figure 7-17. CONTROLLER Con nectio n an d Wirin g Diag ram PWBA ESS PL12.2.7 CN601 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CN501 1 2 3 4 5 6 P/J400 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 P/J501 1 2 3 4 5 6 CN405 CN1 PWBA MCU PL12.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Wiring Connection Diagram be tween Parts 532 11. DUPLEX Figure 7-18. DUPLEX Connection and Wiring Diagram Name of sign al line Remar ks DUPLEX START DUPLEX.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Unpackin g the Print er 533 7.4 Unpa cking the P rinter After unpacking , make sure that there is no missing component, and check the appearance.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Parts Lis t 534 7.5 Part s L is t MAIN UNIT Table 7- 6. MAIN UN IT No. Part Name 01-01-02 TRAY EXTENS ION 01-01-03 COVER TOP 01-01-04 COVER HUSER 01-01-05 .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Parts Lis t 535 04-01-23 SOLENOID PICK UP 04-01-24 SENSOR UPPER PASS 04-01-25 ACUTUATOR EMPTY 04-01-26 H ARN ESS- ASS Y P/ H1 05-01-01 COVER-PH 05-01-02 CH.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Parts Lis t 536 09-01-01 LATCH ASSY-ROTARY 09-01-04 LEVER LATCH 09-01-10 ANTENNA ASSY-CTRG 09-01-15 LEVER CTR G SET 09-01-17 HOLD ER ASS Y-B IAS 09-01-18 S.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Parts Lis t 537 DUPLEX UNIT Table 7-7. DUPLEX UNIT No. Part Name 01-01-02 COVER-R DUP 01-01-03 COVER-L DUP 01-01-04 SCREW THUMB 01-01-06 COVER CONNECTOR 01.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Parts Lis t 538 500-S HEET P APER C ASSETTE UNIT Table 7-8. 500-SHEET PAPER CASSETTE UNI T No. Part Name 01-01- 01 500 P APER C ASSETTE ASSY 01-01 -02 GUID.
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Exploded Di agrams 5 39 7.6 E xplode d Diagram s.
01-01-100 Rev.01 C567 FOR EPSON AcuLaserC1100 NO.1-1 The parts to which no reference number is assigned will not be available as after-sale service parts.
Rev.01 C567 FOR EPSON AcuLaserC1100 NO.12-2 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-ELEC-001 C C B B A A Front 12-02-01 12-02-09 (Onl.
B B A Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.4-1 The parts to which no reference number is assigned will not be available as after-sale service parts.
Front FOR EPSON AcuLaserC1100 NO.5-1 Rev.01 C567 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-002 Leg_Sec005_003EB [Ref PL5.
D D A A C C B B Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.5-2 The parts to which no reference number is assigned will not be available as after-sale service parts.
C Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.6-1 The parts to which no reference number is assigned will not be available as after-sale service parts.
Front F E D D A C C B B Rev.01 C567 FOR EPSON AcuLaserC1100 NO.7-1 The parts to which no reference number is assigned will not be available as after-sale service parts.
Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.8-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-006 08-01-02 08-01-05 Leg_Sec005_007EB .
Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.9-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-007 Leg_Sec005_008EB 09-01-18 09-01-15 .
Front Rev.01 C567 FOR EPSON AcuLaserC1100 NO.9-2 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-008 09-02-13 09-02-10 09-02-13 09-02-10.
Rev.01 C567 FOR EPSON AcuLaserC1100 NO.10-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-009 Leg_Sec005_010EB 10-01-06 10-01-02 10-01.
Front 11-01-09 Rev.01 C567 FOR EPSON AcuLaserC1100 NO.11-1 The parts to which no reference number is assigned will not be available as after-sale service parts.
Rev.01 C567 FOR EPSON AcuLaserC1100 NO.12-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C567-MECH-011 Leg_Sec005_012EB 12-01-06 12-01-09 12-01.
Front Rev.01 FOR DUPLEX UNIT NO.1-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-049A Leg_Sec005_014EB 01-01-03 01-01-04 01-01-04 01-01-06 01-01-02 [Ref PL1.
Rev.01 FOR DUPLEX UNIT NO.1-2 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-050A Leg_Sec005_015EA 01-02-28 01-02-23 01-02-29 01-02-29 .
Rev.01 FOR DUPLEX UNIT NO.1-3 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-051A 01-03-03 01-03-32 01-03-30 01-03-30 Leg_Sec005_016EB (with RING KL) 01-03-99 (with RING KL) 01-03-99 01-03-24 01-03-01 01-03-25 01-03-25 01-03-22 01-03-23 [Ref PL1.
Front Rev.01 FOR DUPLEX UNIT NO.1-4 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-052A Leg_Sec005_017EA 01-04-07 01-04-07 01-04-14 01-.
Rev.01 FOR 500-Sheet Paper Cassette Unit NO.1-1 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-053A Leg_Sec005_018EA All this page incl.
Rev.01 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-054A Leg_Sec005_019EA [Ref PL1.1.
Rev.01 FOR 500-Sheet Paper Cassette Unit NO.1-3 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-055A Leg_Sec005_020EA 01-03-34 01-03-32 [Ref PL1.
Rev.01 FOR 500-Sheet Paper Cassette Unit NO.1-4 The parts to which no reference number is assigned will not be available as after-sale service parts. C802-OPTI-056A Leg_Sec005_021EB 01-04-15 01-04-14 .
EPSON AcuLaser C110 0 Rev is io n B APPENDIX Circuit Dia grams 561 7.7 Circ uit Diag rams C567M AIN ( Tota l: 4 pa ge s).
Model : AcuLaser C1 100/LP-V500 Board : C567MAIN Sheet : 1 of 4 Rev . : A.
Model : AcuLaser C1 100/LP-V500 Board : C567MAIN Sheet : 2 of 4 Rev . : A.
Model : AcuLaser C1 100/LP-V500 Board : C567MAIN Sheet : 3 of 4 Rev . : A.
Model : AcuLaser C1 100/LP-V500 Board : C567MAIN Sheet : 4 of 4 Rev . : A.
Ein wichtiger Punkt beim Kauf des Geräts Epson SEPG04002 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Epson SEPG04002 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Epson SEPG04002 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Epson SEPG04002 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Epson SEPG04002 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Epson SEPG04002 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Epson SEPG04002 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Epson SEPG04002. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Epson SEPG04002 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
