Benutzeranleitung / Produktwartung ES-1200C Pro des Produzenten Epson
Zur Seite of 30
.
EPSON ® ES-1200C Pro PC Getting Started @ Tl& mumal is printed on 50% recycled paper, 10% post-consumer content..
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
Introduction This package contains all the hardware and software you need for professional quality color scanning. Here are the contents of your scanner package, described in the order you’ll need t.
System and Memory Requirements For the scanner hardware and software to work properly, your system must have at least the following configuration: ci cl cl ci Li P D cl cl A 386-based or higher PC or an IBM ® PS/2 ® machine MS-DOS ® 5.0 or higher Microsoft ® Windows 3.
Installing the Interface Card Use this procedure to install a SCSI interface card. For more detailed installation instructions, see the manual that came with your card. 1. Turn off the computer and any peripheral devices. 2. Disconnect the computer’s power cable from the electrical outlet and from the back panel.
10. Replace the cover and reconnect any cables you disconnected. Plug the power cord into an electrical outlet. Setting Up the Scanner Follow these steps to set up the scanner: 1. Take the scanner out of the box and place it on a flat, stable surface with its rear panel facing you.
4. Firmly connect the power cable to the power inlet on the rear of the scanner and the other end into an appropriately grounded outlet as shown below. If the scanner comes on when you plug it in, turn it off by pressing the OPERATE button. Warning: Whenever you turn off the scanner, wait at least 10 seconds before turning it back on.
Connecting the Scanner to the Computer Use this procedure to connect the scanner directly to the SCSI port on your computer using the cable included in the scanner package.
3. Switch on the internal SCSI terminator, as shown. 4. Set the SCSI ID switch to 2, as shown. 5. Turn on the scanner, then the computer. (Always turn on the scanner before the computer.
Installing EZ-SCSI Software If you are running Windows NT, you do not need to install EZ-SCSI software. Skip to the “Installing Adobe Photoshop” procedure. Follow these steps to install the Adaptec EZ-SCSI software: 1. Start Windows. 2. Insert the Adaptec EZ-SCSI Disk 1 in a diskette drive.
10. Remove the final installation disk from the drive and choose Continue. The installation program creates an Adaptec SCSI program group containing Adaptec icons. Installing the EPSON Scanning Utilities The EPSON Scanner Utility program includes EPSON Scan! II and EPSON TWAIN.
6. The next screen prompts you for the path name of the Windows directory. If the displayed path is where your Windows program resides, choose OK. 7. When the Scanner Setup dialog box opens, select SCSI as the interface type. The program supplies the port ID, as shown below.
9. Choose the Test button. If the scanner and EPSON Scanner Utility software are set up correctly, the scanner scans the image; after a few moments, the scanned image appears in the Scanner Setup dialog box, as shown below. Interface SCSI f 10. Choose OK to close the Scanner Setup dialog box.
Installing the ATM program Follow these steps to install Adobe Type Manager: 1. 2. 3. 4. 5. 6. Start Windows. Insert the ATM program disk into a diskette drive. From the Program Manager, open the File menu and choose Run. The Run dialog box appears. Type A:INSTALL (or B:INSTALL) in the Command Line text box and choose OK.
4. Type A:SETUP.EXE (or B:SETUP.EXE) in the Command Line text box and choose OK. The Adobe Photoshop Installer dialog box appears, as shown below. 51951: WJiJK 2841; 5441: 1500 K Space Required: 8412K Space Availabb: 833881: 5. Leave the Installation Options selected.
Selecting the Acquire Device Before you can scan an image from Photoshop, you need to select the scanner as the acquire device. Follow these steps: 1. From the Program Manager, open Photoshop by double-clicking on its icon in the Adobe program group. 2.
lnstalling Kai’s Power Tools Before you install Kai’s Power Tools, make sure that you have installed Adobe Photoshop. Then follow these steps: 1. Insert Disk 1 of Kai’s Power Tools into a diskette drive. 2. From the Program Manager, open the File menu and choose Run.
7. Remove the final installation disk from the drive. You can access Kai’s Power Tools filters from Adobe Photoshop by choosing KPT filters or KPT Extensions from the Filters menu in the Photoshop Menu Bar. For more information on Photoshop or the installation options, consult the Kai’s Power Tools for Windows Explorer‘s Guide.
3. Carefully close the document cover so that you do not disturb the position of the photograph on the glass. Choose Acquire in the File menu; then choose TWAIN.
5. In the scroll bar next to the Image Type button, select the image type appropriate for your scan. If you are scanning a color photograph, select Color Photo. 6. Click on the full-page Preview icon, , at the bottom of the dialog box. This does a fast preview scan so you can see the scan area.
When you have defined the portion of the image you want to scan, choose the Scan button. In a few moments, the scanned image is imported into the Photoshop window. To see the scanned image, close the EPSON TWAIN dialog box. Once you have your images and text, you can put them together in reports, newsletters, brochures, or business presentations.
Calibrating Your System Calibration allows you to match your scanner and your output device so that you can reproduce images that are very close to the original. Monitors use a different technology than printers, so images look different on the monitor than when they are printed.
2. Choose Screen Calibration from the Calibrate menu. You see the screen shown below: I I Adjust the slider below until the gray areas appear the same. I I I &, I I & 3. Look at the display from a distance and adjust the slide bar until the separate rows have the same basic color intensity.
Note: If you change your display monitor, you will need to create a new screen calibration profile. Do this by selecting Calibration Profile in the Configuration dialog box. The new screen calibration profile overrides the old one. Exporting a calibration chart Follow these steps to export a calibration chart from Scan! to your application: 1.
7. Open the file for the calibration chart file you exported. The chart contains nine blocks of color gradations surrounded by a black border on three sides and a gray border with some grayscale gradations on top. 8. Save the calibration chart file within Photoshop by selecting Save from the File menu.
5. In the File Name field, type the filename of the calibration file you want to create. Make sure you assign a CAL extension to this file. 6. In the Description field, type a short description of the printer you use to print the calibration chart. 7.
The scanner scans the image using information from the calibration profile to produce the best possible image for your printer. Selecting the Right Resolution Selecting the best resolution for scanning your image hinges on two factors: the final output device you plan to print the image on, and the acceptable file size.
Copyrighted Materials Like photocopiers, scanners can be misused by improper copying of copyrighted material. Although Section 107 of the U.S. Copyright Act of 1976 (Title 17, United States Code), the “fair use” doctrine, permits limited copying in certain circumstances, those circumstances may not be as broad as some people assume.
Epson America, Inc. 20770 Madrona Avenue Torrance, California 90503 CPD20838/94.
Ein wichtiger Punkt beim Kauf des Geräts Epson ES-1200C Pro (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Epson ES-1200C Pro noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Epson ES-1200C Pro - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Epson ES-1200C Pro reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Epson ES-1200C Pro erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Epson ES-1200C Pro besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Epson ES-1200C Pro verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Epson ES-1200C Pro. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Epson ES-1200C Pro gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
