Benutzeranleitung / Produktwartung CM Version 1.0 des Produzenten Enterasys Networks
Zur Seite of 38
Enterasys Matrix ™ X Router DC Power Supply P/N 9034200 Installation Guide.
.
i Notice Enterasys Networks reserv es the right to make changes in specifications and other information contained in th is document and its web site without prior notice.
ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device com plies with Pa r t 15 of the FC C rules.
iii Electromagnetic Compatibility (EMC) This product complies with the following: 47 CF R Pa r t s 2 and 15, CSA C108.8, 2006/95/EC, EN 55022, EN 61000 ‐ 3 ‐ 2, EN 61000 ‐ 3 ‐ 3, EN 55024, AS/NZS CISPR 22, VCCI V ‐ 3.
iv ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 .
v VCCI Notice This is a class A product based on the standard of the Vo l u n t a r y Control Coun cil for Interference by Information Te c h n o l o g y Equipment (VCCI).
vi Declaration of Conformity Application of Co uncil Directiv e(s): 2004/108/EC 2006/95/EC Manufacturer ’ s Name: Enterasys Networks, Inc. Manufacturer ’ s Address: 50 Minuteman Road Andover , MA 01810 USA European Representativ e Address: Enterasys Networks, Ltd.
vii Enterasys Networks, Inc. Fi rmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“ Agreement”) betwee n the end user (“Y ou”) and Enterasys Networks, In c.
viii 4. EXPORT RESTRICTIONS. You understand that Entera sys and its Affiliates are subject to regulation by agencies of the U.
ix 8. AUDIT RIGHTS. You here by acknow ledge that the intellectual property rights associated with the Prog ram are of critical value .
x.
xi Contents Chapter 1: DC Power Supply Installation Overview of the DC Power Supply .. ................ ................ ............. ................. ................ ............... .... .. 1-2 Power Supply Redundancy Planning .............. .....
xii.
Matrix X Router DC Power Supply Installation Guide xiii About This Guide This guide describes the Enterasys Matrix ™ X Router DC power supply features .
Conventions Used in This Guide xiv About This Guide Documentation can be accessed on the Wo r l d Wide We b , at the following URL: http://www .
Getting Help Matrix X Router DC Power Supply Installation Guide xv Getting Help For additional support related to the DC pow er supply or this document, .
Getting Help xvi About This Guide.
Matrix X Router DC Power Supply Installation Guide 1-1 1 DC Power Supply Installation This chapter provides installation instructions for the Enterasys Matrix™ X Router DC power supply module (X ‐ DC ).
Overview of the DC Power Supply 1-2 DC Power Supply Installation Overview of the DC Power Supply The DC power suppl y (X ‐ DC) can be used in the Enterasy s .
Overview of the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-3 Figure 1-2 Back V iew of the DC Power Supply The DC power suppl y provides the following .
Installation Site Requirements 1-4 DC Power Supply Installation Power Supply Redundancy Planning Because chassis syste m components consume va r yi n g amounts of elect.
Pre-Installation Tasks Matrix X Router DC Power Supply Installation Guide 1-5 Pre-Inst allation T asks Complete the followin g tasks before installing the DC power .
Pre-Installation Tasks 1-6 DC Power Supply Installation 2. Use the information from the output of the show system hardware command to fill out the worksheet in Ta b l e 1 ‐ 1 for each module as follows: a.
Pre-Installation Tasks Matrix X Router DC Power Supply Installation Guide 1-7 New DC Power Matrix X System Inst allations If the system is a new Matrix X DC ‐ pow ered installation, fol low this procedure to ve ri fy DC power compliance of all modules: 1.
Pre-Installation Tasks 1-8 DC Power Supply Installation Prep are Site Wiring fo r DC Power Inst allation 1. Ensure that a branch circuit disconnect device is installed,.
Unpacking the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-9 Unp acking the DC Power Supply To unpack the DC power supply: 1. Open the box and remov e the packing material protecting the DC power supply.
Installing the DC Power Supply 1-10 DC Power Supply Installation 3. Remove the tape seal on the non ‐ conductiv e bag to remov e the module.
Installing the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-11 2. Remove the vent plate covering all powe r supply slots by loosening the top and bottom captive screws, as shown in Figure 1 ‐ 3 .
Installing the DC Power Supply 1-12 DC Power Supply Installation 5. Hold the power supply by placing one ha nd on the handle located on the front panel and using you r other hand to support the power supply .
Installing the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-13 Figure 1-5 Removin g Blank Co verplate from Power Supply Slot 10. Connect the chassis to earth ground utilizing the earth ground connection on the back of the unit.
Removing a Power Supply 1-14 DC Power Supply Installation b. Place the lock wa s h e r s over the positive and negative studs. c. Place the nuts ov er the lock was h e r s and tighten.
Removing a Power Supply Matrix X Router DC Power Supply Installation Guide 1-15 Caution: If you want to operate the chassis with only one power supply , be sure to install the coverplate in place of the removed power supply to contain EMI radiation and ensure proper air circulation.
Removing a Power Supply 1-16 DC Power Supply Installation.
Matrix X Router DC Power Supply Installation Guide 2-1 2 DC Power Supply Specifications This chapter provides the DC power supply specifications and regulatory complianc e information. S pecifications Ta b l e 2 ‐ 1 lists the physical specifications.
Power Supply Redundancy 2-2 DC Power Supply Specifications Compression Lugs The DC power supply positive and negative bolt patterns match up to a 1/4 ‐ inch diame ter , 2 ‐ hole compression lug spaced 5/8 ‐ inch on center .
Power Supply Redundancy Matrix X Router DC Power Supply Installation Guide 2-3 T able 2-3 Modu le Power Spe cifications Module @ 48 VDC Power (W atts) Thermal Output (BTU/HR) CM 97 W atts 331.1 BTU/HR Fan tray 85 W atts 290.1 BTU/HR X4-FM 30 W atts 102.
Regulatory Compliance 2-4 DC Power Supply Specifications Regulatory Compliance The DC power suppl y meets the safety and electromagnetic compatibil ity (EMC) requirements listed in Ta b l e 2 ‐ 5 : T able 2-5 Complia nce St andards Regulatory Compliance Stan da r ds Safety UL 60950, CSA C22.
Ein wichtiger Punkt beim Kauf des Geräts Enterasys Networks CM Version 1.0 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Enterasys Networks CM Version 1.0 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Enterasys Networks CM Version 1.0 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Enterasys Networks CM Version 1.0 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Enterasys Networks CM Version 1.0 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Enterasys Networks CM Version 1.0 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Enterasys Networks CM Version 1.0 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Enterasys Networks CM Version 1.0. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Enterasys Networks CM Version 1.0 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
