Benutzeranleitung / Produktwartung GF7050VT-M5 des Produzenten ECS
Zur Seite of 64
.
.
Preface Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author .
ii Preface Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • T.
iii Chapter 3 27 Using BIOS 2 7 About the Setup Utility ................................................................ 27 The Standard Configuration..............................................27 Entering the Setup Utility .........................
iv Integrated Peripherals.......................................................34 Power Management Setup.................................................35 PCI/PNP Configuration.....................................................37 PC Health Status.
1 Introducing the Motherboard Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the GF7050VT -M5 motherboard. This motherboard is a high performance, enhanced function motherbo.
2 Introducing the Motherboard Feature Processor • Accommodates Intel ® Core TM 2 Quad*/Core TM 2 Duo /Pentium ® D*/ Pentium ® 4*/Celeron ® D processors • Supports a system bus (FSB) of 1333/10.
3 Introducing the Motherboard 1. Some hardware specifications and software items are subject to change without prior notice. 2. Due to chipset limitation, we recommend that motherboard be oper- ated in the ambiance between 0 and 50 °C .
4 Introducing the Motherboard Motherboard Components.
5 Introducing the Motherboard T able of Motherboard Components This concludes Chapter 1. The next chapter explains how to install the motherboard. L A BEL C O M P O NENT S LG A 775 s oc k et f or I ntel ® Co r e TM 2 Q uad*/C or e TM 2 D uo/P ent i um ® D */P en ti um ® 4*/C eler on ® D CP Us 2.
6 Introducing the Motherboard Memo.
7 Installing the Motherboard Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a ground.
8 Installing the Motherboard Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered.
9 Installing the Motherboard Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings 1. T o avoid the system unstability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Optimal Defaults” and then “Save Changes and Exit”.
10 Installing the Motherboard Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resis- tors with the clip of the cooling fan.
11 Installing the Motherboard A. Read and follow the instructions shown on the sticker on the CPU cap. B. Unload the cap · Use thumb & forefinger to hold the lifting tab of the cap. · Lift the cap up and remove the cap completely from the socket.
12 Installing the Motherboard Installation Procedure Refer to the following to install the memory modules. 1 This motherboard supports unbuffered DDR2 SDRAM only . 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot.
13 Installing the Motherboard T able A: DDR2 (memory module) QVL (Qualified V endor List) The following DDR2 memory modules have been tested and qualified for use with this motherboard. Typ e Si z e Ven d o r Mo d u l e Na m e A eneon A ET660U D00- 370A 98Z Infineo n HYS 64T64400H U- 3 .
14 Installing the Motherboard Expansion Slots Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities.
15 Installing the Motherboard Follow these instructions to install an add-on card: 1 Remove a blanking plate from the system case corresponding to the slot you are going to use. 2 Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
16 Installing the Motherboard Connecting Optional Devices Refer to the following for information on connecting the motherboard’ s optional devices: SA T A1~4: Serial A T A connectors These connectors are used to support the new Serial A T A devices for the highest date transfer rates (3.
17 Installing the Motherboard F_USB1~2: Front Panel USB headers The motherboard has four USB ports installed on the rear edge I/O port array . Additionally , some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
18 Installing the Motherboard LPT : Onboard p arallel port header This is a header that can be used to connect to the printer, scanner or other devices.
19 Installing the Motherboard IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLA VE. Refer to the IDE device user’ s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLA VE.
20 Installing the Motherboard Refer to the illustration below for proper installation: This motherboard supports the “Hot-Plug” function. 1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SA T A hard drive.
21 Installing the Motherboard Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Serial Port Use the COM port to connect serial devices such as mouse (COM) or fax/modems.
22 Installing the Motherboard Connecting Case Components 1 Connect the CPU cooling fan cable to CPU_F AN . 2 Connect the system cooling fan connector to SYS_F AN . 3 Connect the standard power supply connector to A TX_POWER . 4 Connect the auxiliary case power supply connector to A TX12V .
23 Installing the Motherboard A TX12V : A TX 12V Power Connector Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V . A TX_POWER: A TX 24-pin Power Connector Pin Signal Name Pin Signal Name 1 +3.3V 13 +3.
24 Installing the Motherboard 4 Speaker Signal 3 GND 2 NC 1 +5V Pin Signal Name SPK: Internal speaker header Front Panel Header The front panel header (F_P ANEL ) provides a standard set of switch and LED headers commonly found on A TX or Micro A TX cases.
25 Installing the Motherboard Power Switch Supporting the power on/off function requires connecting pins 6 and 8 to a momen- tary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off.
26 Installing the Motherboard Memo.
27 Introducing the Motherboard Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc.” BIOS with support for Windows Plug and Play . The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
28 Introducing the Motherboard BIOS Navigation Keys The BIOS navigation keys are listed below: Press the delete key to access the BIOS Setup Utility . K E Y FUNCTION Scrolls through the items on a men.
29 Introducing the Motherboard For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS.
30 Introducing the Motherboard LBA/Large Mode (Auto) Use this item to set the LAB/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time. Block (Multi-Sector Transfer) (Auto) If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer .
31 Introducing the Motherboard Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer . CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc.
32 Introducing the Motherboard 1st/2nd/3rd Boot Device (Hard Drive/CD/DVD/1st FLOPPY DRIVE) Use this item to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard.
33 Introducing the Motherboard Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer . CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc.
34 Introducing the Motherboard Onboard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function. Onboard LAN Boot ROM (Disabled) Use this item to enable or disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed.
35 Introducing the Motherboard Power Management Setup This page sets up some parameters for system power management operation. Select the ACPI state used for System Sus- pend. Help Item CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc.
36 Introducing the Motherboard Soft-Off By PWR-BTTN (Instant Off) Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by W ake Up Alarms. This item lets you install a software power down that is con- trolled by the power button on your system.
37 Introducing the Motherboard Init Display First (PCI) Use this item to select which graphics controller to use as the primary boot devices. PCI / PnP Configuration This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability .
38 Introducing the Motherboard CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc. Smart Fan Function Help Item Smart Fan Function f Scroll to this item and press <Enter> to .
39 Introducing the Motherboard Frequency/V oltage Control This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have in- stalled in your system. CMOS Setup Utility - Copyright (C) 1985-2007, American Megatrends, Inc.
40 Introducing the Motherboard Change Supervisor Password (Press Enter) Y ou can select this option and press <Enter> to access the sub menu. Y ou can use the sub menu to change the supervisor password. Load Default Settings This option opens a dialog box to ask if you are sure to install optimized defaults or not.
41 Introducing the Motherboard Save & Exit Setup Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility . When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.
42 Introducing the Motherboard This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard. Updating the BIOS Y ou can download and install updated BIOS for this motherboard from the manufacturer ’ s W eb site.
43 Using the Motherboard Software Chapter 4 Using the Motherboard Software Auto-installing under Windows XP/V ista The support software CD-ROM disc loads automatically under W indows XP/V ista. When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen.
44 Using the Motherboard Software Setup T ab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that al- lows you to open Windows Explorer and show the contents of the support CD.
45 Using the Motherboard Software 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recom- mended. 4. Click Next run the Installation Wizard. An item installation screen appears: 5.
46 Using the Motherboard Software Method 1. Run Reboot Setup Windows V ista will block startup programs by default when installing drivers after the system restart. Y ou must select taskbar icon Run Blocked Program and run Reboot Setup to install the next driver, until you finish all drivers installation.
47 Using the Motherboard Software 2. Select Classic View . 3. Set User Account . 4. Select Turn User Account Control on or off and press Continue ..
48 Using the Motherboard Software Manual Installation Insert the CD in the CD-ROM drive and locate the P A TH.DOC file in the root directory . This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers.
49 NVIDIA RAID Configuration Chapter 5 Setting Up NVIDIA RAID Configuration Setting Up a Non-Bootable RAID Array Setting Up the BIOS Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter . The Integrated Peripherals window appears.
50 NVIDIA RAID Configuration From the Integrated Peripherals W indow , globally set SA T A Mode select to RAID Mode (see Figure 1.2). Press F10 to save the configuration and exit (F10 is the navigation key to Installing the NVIDIA RAID Software Under Windows This section describes how to run the setup application and install the RAID soft- ware.
51 NVIDIA RAID Configuration Setting Up a Bootable RAID Array This section explains how to configure a bootable NVIDIA RAID array . Setting Up the BIOS Use the arrow keys to select Integrated Peripherals (see Figure 1.4), then press Enter . The Integrated Peripherals screen (or a screen similar to it) appears.
52 NVIDIA RAID Configuration Configuring the NVIDIA RAID BIOS The NVIDIA RAID BIOS set up lets you choose the RAID type and which hard drives you want to make part of the array . Entering the RAID BIOS Setup: 1 W ait until you see the RAID software prompting you to press F10.
53 NVIDIA RAID Configuration The NVIDIA RAID Utility—Define a New Array screen appears (Figure 1.7). Figure 1.7 MediaShield BIOS By default, RAID Mode is set to Mirroring and Striping Block is set to Optimal.
54 NVIDIA RAID Configuration Figure 1.8 illustrates the Define a New Array screen after one disk have been assigned as RAID 0 array disk. Figure 1.8 MediaShield BIOS—Array Disks Assigned Completing the RAID BIOS Setup Figure 1.9 Clear Disk Data Prompt After assigning your RAID array disk, press F7.
55 NVIDIA RAID Configuration Figure 1.10 Array List Window Press Y to clear the disk data. The Array List screen appears, where you can review the RAID arrays that you have set up.
56 NVIDIA RAID Configuration 1 Copy all files in "…IDEWinXPsataraid" to a floppy disk. (For Windows 2000, substitute "Win2K" in the path.
57 NVIDIA RAID Configuration b Select “NVIDIA RAID CLASS DRIVER (required)” and then press Enter . c Press S again at the Specify Devices screen, then press Enter . d Select “NVIDIA NForce Storage Controller (required)” and then press Enter . The following Windows Setup screen appears listing both drivers:.
58 NVIDIA RAID Configuration Memo.
Ein wichtiger Punkt beim Kauf des Geräts ECS GF7050VT-M5 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ECS GF7050VT-M5 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ECS GF7050VT-M5 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ECS GF7050VT-M5 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ECS GF7050VT-M5 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ECS GF7050VT-M5 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ECS GF7050VT-M5 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ECS GF7050VT-M5. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ECS GF7050VT-M5 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
